- 30 Nov, 2017 40 commits
-
-
Ryan Hsu authored
[ Upstream commit d2e202c0 ] With command to get board_id from otp, in the case of following boot get otp board id result 0x00000000 board_id 0 chip_id 0 boot using board name 'bus=pci,bmi-chip-id=0,bmi-board-id=0" ... failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=0 from ath10k/QCA6174/hw3.0/board-2.bin The invalid board_id=0 will be used as index to search in the board-2.bin. Ignore the case with board_id=0, as it means the otp is not carrying the board id information. Signed-off-by:
Ryan Hsu <ryanhsu@qca.qualcomm.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ryan Hsu authored
[ Upstream commit 88407beb ] Ath10k reports the phy capability that supports P2P_DEVICE interface. When we use the P2P supported wpa_supplicant to start connection, it'll create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE p2p-dev-wlan0 which is for p2p control channel (vdev_id=1). ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0 ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0 ... ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1 ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0 And the txpower in per vif bss_conf will only be set to valid tx power when the interface is assigned with channel_ctx. But this P2P_DEVICE interface will never be used for any connection, so that the uninitialized bss_conf.txpower=0 is assinged to the arvif->txpower when interface created. Since the txpower configuration is firmware per physical interface. So the smallest txpower of all vifs will be the one limit the tx power of the physical device, that causing the low txpower issue on other active interfaces. wlan0: Limiting TX power to 21 (24 - 3) dBm ath10k_pci mac vdev_id 0 txpower 21 ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0 ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21 ath10k_pci mac txpower 0 This issue only happens when we use the wpa_supplicant that supports P2P or if we use the iw tool to create the control P2P_DEVICE interface. Signed-off-by:
-
Daniel Vetter authored
[ Upstream commit 7357f899 ] I reported the include issue for tracepoints a while ago, but nothing seems to have happened. Now it bit us, since the drm_mm_print conversion was broken for armada. Fix it, so I can re-enable armada in the drm-misc build configs. v2: Rebase just the compile fix on top of Chris' build fix. Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Chris Wilson <chris@chris-wilson.co.uk> Acked: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1483115932-19584-1-git-send-email-daniel.vetter@ffwll.chSigned-off-by:
-
Thomas Preisner authored
[ Upstream commit 107fded7 ] In a few cases the err-variable is not set to a negative error code if a function call in typhoon_init_one() fails and thus 0 is returned instead. It may be better to set err to the appropriate negative error code before returning. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188841Reported-by:
Pan Bian <bianpan2016@163.com> Signed-off-by:
Thomas Preisner <thomas.preisner+linux@fau.de> Signed-off-by:
Milan Stephan <milan.stephan+linux@fau.de> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Thomas Preisner authored
[ Upstream commit 6b6bbb59 ] In some cases the return value of a failing function is not being used and the function typhoon_init_one() returns another negative error code instead. Signed-off-by:
-
David Ahern authored
[ Upstream commit 7bb387c5 ] IP_MULTICAST_IF fails if sk_bound_dev_if is already set and the new index does not match it. e.g., ntpd[15381]: setsockopt IP_MULTICAST_IF 192.168.1.23 fails: Invalid argument Relax the check in setsockopt to allow setting mc_index to an L3 slave if sk_bound_dev_if points to an L3 master. Make a similar change for IPv6. In this case change the device lookup to take the rcu_read_lock avoiding a refcnt. The rcu lock is also needed for the lookup of a potential L3 master device. This really only silences a setsockopt failure since uses of mc_index are secondary to sk_bound_dev_if if it is set. In both cases, if either index is an L3 slave or master, lookups are directed to the same FIB table so relaxing the check at setsockopt time causes no harm. Patch is based on a suggested change by Darwin for a problem noted in their code base. Suggested-by:
Darwin Dingel <darwin.dingel@alliedtelesis.co.nz> Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
-
Shawn Guo authored
[ Upstream commit fc318d64 ] The zx_dma driver supports cyclic transfer mode. Let's set DMA_CYCLIC cap_mask bit to make that clear, and avoid unnecessary failure when clients request channel via dma_request_chan_by_mask() with DMA_CYCLIC bit set in mask. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Reviewed-by:
Jun Nie <jun.nie@linaro.org> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Bjorn Helgaas authored
[ Upstream commit 977509f7 ] Previously we didn't check the type of device before trying to apply Type 1 (PCI-X) or Type 2 (PCIe) Setting Records from _HPX. We don't support PCI-X Setting Records, so this was harmless, but the warning was useless. We do support PCIe Setting Records, and we didn't check whether a device was PCIe before applying settings. I don't think anything bad happened on non-PCIe devices because pcie_capability_clear_and_set_word(), pcie_cap_has_lnkctl(), etc., would fail before doing any harm. But it's ugly to depend on those internals. Check the device type before attempting to apply Type 1 and Type 2 Setting Records (Type 0 records are applicable to PCI, PCI-X, and PCIe devices). A side benefit is that this prevents useless "not supported" warnings when a BIOS supplies a Type 1 (PCI-X) Setting Record and we try to apply it to every single device: pci 0000:00:00.0: PCI-X settings not supported After this patch, we'll get the warning only when a BIOS supplies a Type 1 record and we have a PCI-X device to which it should be applied. Link: https://bugzilla.kernel.org/show_bug.cgi?id=187731Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Santosh Shilimkar authored
[ Upstream commit 584a8279 ] The first message to a remote node should prompt a new connection even if it is RDMA operation. For RDMA operation the MR mapping can fail because connections is not yet up. Since the connection establishment is asynchronous, we make sure the map failure because of unavailable connection reach to the user by appropriate error code. Before returning to the user, lets trigger the connection so that its ready for the next retry. Signed-off-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
-
Benjamin Poirier authored
commit 19110cfb upstream. Lennart reported the following race condition: \ e1000_watchdog_task \ e1000e_has_link \ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link /* link is up */ mac->get_link_status = false; /* interrupt */ \ e1000_msix_other hw->mac.get_link_status = true; link_active = !hw->mac.get_link_status /* link_active is false, wrongly */ This problem arises because the single flag get_link_status is used to signal two different states: link status needs checking and link status is down. Avoid the problem by using the return value of .check_for_link to signal the link status to e1000e_has_link(). Reported-by:
Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by:
Benjamin Poirier <bpoirier@suse.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
Amit Pundir <amit.pundir@linaro.org> Signed-off-by:
-
Benjamin Poirier authored
commit d3509f8b upstream. All the helpers return -E1000_ERR_PHY. Signed-off-by:
-
Benjamin Poirier authored
commit c4c40e51 upstream. In case of error from e1e_rphy(), the loop will exit early and "success" will be set to true erroneously. Signed-off-by:
-
Tobias Jordan authored
commit 7978db34 upstream. The for_each_available_child_of_node() loop in _of_add_opp_table_v2() doesn't drop the reference to "np" on errors. Fix that. Fixes: 27465902 (PM / OPP: Add support to parse "operating-points-v2" bindings) Signed-off-by:
Tobias Jordan <Tobias.Jordan@elektrobit.com> [ VK: Improved commit log. ] Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Tuomas Tynkkynen authored
commit 9523feac upstream. Because userspace gets Very Unhappy when calls like stat() and execve() return -EINTR on 9p filesystem mounts. For instance, when bash is looking in PATH for things to execute and some SIGCHLD interrupts stat(), bash can throw a spurious 'command not found' since it doesn't retry the stat(). In practice, hitting the problem is rare and needs a really slow/bogged down 9p server. Signed-off-by:
Tuomas Tynkkynen <tuomas@tuxera.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Eric Biggers authored
commit a0b3bc85 upstream. fscrypt_initialize(), which allocates the global bounce page pool when an encrypted file is first accessed, uses "double-checked locking" to try to avoid locking fscrypt_init_mutex. However, it doesn't use any memory barriers, so it's theoretically possible for a thread to observe a bounce page pool which has not been fully initialized. This is a classic bug with "double-checked locking". While "only a theoretical issue" in the latest kernel, in pre-4.8 kernels the pointer that was checked was not even the last to be initialized, so it was easily possible for a crash (NULL pointer dereference) to happen. This was changed only incidentally by the large refactor to use fs/crypto/. Solve both problems in a trivial way that can easily be backported: just always take the mutex. It's theoretically less efficient, but it shouldn't be noticeable in practice as the mutex is only acquired very briefly once per encrypted file. Later I'd like to make this use a helper macro like DO_ONCE(). However, DO_ONCE() runs in atomic context, so we'd need to add a new macro that allows blocking. Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 4bdced5c upstream. When a CPU lowers its priority (schedules out a high priority task for a lower priority one), a check is made to see if any other CPU has overloaded RT tasks (more than one). It checks the rto_mask to determine this and if so it will request to pull one of those tasks to itself if the non running RT task is of higher priority than the new priority of the next task to run on the current CPU. When we deal with large number of CPUs, the original pull logic suffered from large lock contention on a single CPU run queue, which caused a huge latency across all CPUs. This was caused by only having one CPU having overloaded RT tasks and a bunch of other CPUs lowering their priority. To solve this issue, commit: b6366f04 ("sched/rt: Use IPI to trigger RT task push migration instead of pulling") changed the way to request a pull. Instead of grabbing the lock of the overloaded CPU's runqueue, it simply sent an IPI to that CPU to do the work. Although the IPI logic worked very well in removing the large latency build up, it still could suffer from a large number of IPIs being sent to a single CPU. On a 80 CPU box, I measured over 200us of processing IPIs. Worse yet, when I tested this on a 120 CPU box, with a stress test that had lots of RT tasks scheduling on all CPUs, it actually triggered the hard lockup detector! One CPU had so many IPIs sent to it, and due to the restart mechanism that is triggered when the source run queue has a priority status change, the CPU spent minutes! processing the IPIs. Thinking about this further, I realized there's no reason for each run queue to send its own IPI. As all CPUs with overloaded tasks must be scanned regardless if there's one or many CPUs lowering their priority, because there's no current way to find the CPU with the highest priority task that can schedule to one of these CPUs, there really only needs to be one IPI being sent around at a time. This greatly simplifies the code! The new approach is to have each root domain have its own irq work, as the rto_mask is per root domain. The root domain has the following fields attached to it: rto_push_work - the irq work to process each CPU set in rto_mask rto_lock - the lock to protect some of the other rto fields rto_loop_start - an atomic that keeps contention down on rto_lock the first CPU scheduling in a lower priority task is the one to kick off the process. rto_loop_next - an atomic that gets incremented for each CPU that schedules in a lower priority task. rto_loop - a variable protected by rto_lock that is used to compare against rto_loop_next rto_cpu - The cpu to send the next IPI to, also protected by the rto_lock. When a CPU schedules in a lower priority task and wants to make sure overloaded CPUs know about it. It increments the rto_loop_next. Then it atomically sets rto_loop_start with a cmpxchg. If the old value is not "0", then it is done, as another CPU is kicking off the IPI loop. If the old value is "0", then it will take the rto_lock to synchronize with a possible IPI being sent around to the overloaded CPUs. If rto_cpu is greater than or equal to nr_cpu_ids, then there's either no IPI being sent around, or one is about to finish. Then rto_cpu is set to the first CPU in rto_mask and an IPI is sent to that CPU. If there's no CPUs set in rto_mask, then there's nothing to be done. When the CPU receives the IPI, it will first try to push any RT tasks that is queued on the CPU but can't run because a higher priority RT task is currently running on that CPU. Then it takes the rto_lock and looks for the next CPU in the rto_mask. If it finds one, it simply sends an IPI to that CPU and the process continues. If there's no more CPUs in the rto_mask, then rto_loop is compared with rto_loop_next. If they match, everything is done and the process is over. If they do not match, then a CPU scheduled in a lower priority task as the IPI was being passed around, and the process needs to start again. The first CPU in rto_mask is sent the IPI. This change removes this duplication of work in the IPI logic, and greatly lowers the latency caused by the IPIs. This removed the lockup happening on the 120 CPU machine. It also simplifies the code tremendously. What else could anyone ask for? Thanks to Peter Zijlstra for simplifying the rto_loop_start atomic logic and supplying me with the rto_start_trylock() and rto_start_unlock() helper functions. Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Clark Williams <williams@redhat.com> Cc: Daniel Bristot de Oliveira <bristot@redhat.com> Cc: John Kacur <jkacur@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Scott Wood <swood@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20170424114732.1aac6dc4@gandalf.local.homeSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Ricardo Ribalda Delgado authored
commit 9cac9d2f upstream. VIDIOC_DQEVENT and VIDIOC_QUERY_EXT_CTRL should give the same output for the control flags field. This patch creates a new function user_flags(), that calculates the user exported flags value (which is different than the kernel internal flags structure). This function is then used by all the code that exports the internal flags to userspace. Reported-by:
Dimitrios Katsaros <patcherwork@gmail.com> Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Johan Hovold authored
commit 6c3b047f upstream. Make sure to check that we actually have an Interface Association Descriptor before dereferencing it during probe to avoid dereferencing a NULL-pointer. Fixes: e0d3bafd ("V4L/DVB (10954): Add cx231xx USB driver") Reported-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Tested-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Sean Young authored
commit 3e45067f upstream. The ioctl LIRC_SET_REC_TIMEOUT would set a timeout of 704ns if called with a timeout of 4294968us. Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Michele Baldessari authored
commit b3120d2c upstream. Firmware load on AS102 is using the stack which is not allowed any longer. We currently fail with: kernel: transfer buffer not dma capable kernel: ------------[ cut here ]------------ kernel: WARNING: CPU: 0 PID: 598 at drivers/usb/core/hcd.c:1595 usb_hcd_map_urb_for_dma+0x41d/0x620 kernel: Modules linked in: amd64_edac_mod(-) edac_mce_amd as102_fe dvb_as102(+) kvm_amd kvm snd_hda_codec_realtek dvb_core snd_hda_codec_generic snd_hda_codec_hdmi snd_hda_intel snd_hda_codec irqbypass crct10dif_pclmul crc32_pclmul snd_hda_core snd_hwdep snd_seq ghash_clmulni_intel sp5100_tco fam15h_power wmi k10temp i2c_piix4 snd_seq_device snd_pcm snd_timer parport_pc parport tpm_infineon snd tpm_tis soundcore tpm_tis_core tpm shpchp acpi_cpufreq xfs libcrc32c amdgpu amdkfd amd_iommu_v2 radeon hid_logitech_hidpp i2c_algo_bit drm_kms_helper crc32c_intel ttm drm r8169 mii hid_logitech_dj kernel: CPU: 0 PID: 598 Comm: systemd-udevd Not tainted 4.13.10-200.fc26.x86_64 #1 kernel: Hardware name: ASUS All Series/AM1I-A, BIOS 0505 03/13/2014 kernel: task: ffff979933b24c80 task.stack: ffffaf83413a4000 kernel: RIP: 0010:usb_hcd_map_urb_for_dma+0x41d/0x620 systemd-fsck[659]: /dev/sda2: clean, 49/128016 files, 268609/512000 blocks kernel: RSP: 0018:ffffaf83413a7728 EFLAGS: 00010282 systemd-udevd[604]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. kernel: RAX: 000000000000001f RBX: ffff979930bce780 RCX: 0000000000000000 kernel: RDX: 0000000000000000 RSI: ffff97993ec0e118 RDI: ffff97993ec0e118 kernel: RBP: ffffaf83413a7768 R08: 000000000000039a R09: 0000000000000000 kernel: R10: 0000000000000001 R11: 00000000ffffffff R12: 00000000fffffff5 kernel: R13: 0000000001400000 R14: 0000000000000001 R15: ffff979930806800 kernel: FS: 00007effaca5c8c0(0000) GS:ffff97993ec00000(0000) knlGS:0000000000000000 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: 00007effa9fca962 CR3: 0000000233089000 CR4: 00000000000406f0 kernel: Call Trace: kernel: usb_hcd_submit_urb+0x493/0xb40 kernel: ? page_cache_tree_insert+0x100/0x100 kernel: ? xfs_iunlock+0xd5/0x100 [xfs] kernel: ? xfs_file_buffered_aio_read+0x57/0xc0 [xfs] kernel: usb_submit_urb+0x22d/0x560 kernel: usb_start_wait_urb+0x6e/0x180 kernel: usb_bulk_msg+0xb8/0x160 kernel: as102_send_ep1+0x49/0xe0 [dvb_as102] kernel: ? devres_add+0x3f/0x50 kernel: as102_firmware_upload.isra.0+0x1dc/0x210 [dvb_as102] kernel: as102_fw_upload+0xb6/0x1f0 [dvb_as102] kernel: as102_dvb_register+0x2af/0x2d0 [dvb_as102] kernel: as102_usb_probe+0x1f3/0x260 [dvb_as102] kernel: usb_probe_interface+0x124/0x300 kernel: driver_probe_device+0x2ff/0x450 kernel: __driver_attach+0xa4/0xe0 kernel: ? driver_probe_device+0x450/0x450 kernel: bus_for_each_dev+0x6e/0xb0 kernel: driver_attach+0x1e/0x20 kernel: bus_add_driver+0x1c7/0x270 kernel: driver_register+0x60/0xe0 kernel: usb_register_driver+0x81/0x150 kernel: ? 0xffffffffc0807000 kernel: as102_usb_driver_init+0x1e/0x1000 [dvb_as102] kernel: do_one_initcall+0x50/0x190 kernel: ? __vunmap+0x81/0xb0 kernel: ? kfree+0x154/0x170 kernel: ? kmem_cache_alloc_trace+0x15f/0x1c0 kernel: ? do_init_module+0x27/0x1e9 kernel: do_init_module+0x5f/0x1e9 kernel: load_module+0x2602/0x2c30 kernel: SYSC_init_module+0x170/0x1a0 kernel: ? SYSC_init_module+0x170/0x1a0 kernel: SyS_init_module+0xe/0x10 kernel: do_syscall_64+0x67/0x140 kernel: entry_SYSCALL64_slow_path+0x25/0x25 kernel: RIP: 0033:0x7effab6cf3ea kernel: RSP: 002b:00007fff5cfcbbc8 EFLAGS: 00000246 ORIG_RAX: 00000000000000af kernel: RAX: ffffffffffffffda RBX: 00005569e0b83760 RCX: 00007effab6cf3ea kernel: RDX: 00007effac2099c5 RSI: 0000000000009a13 RDI: 00005569e0b98c50 kernel: RBP: 00007effac2099c5 R08: 00005569e0b83ed0 R09: 0000000000001d80 kernel: R10: 00007effab98db00 R11: 0000000000000246 R12: 00005569e0b98c50 kernel: R13: 00005569e0b81c60 R14: 0000000000020000 R15: 00005569dfadfdf7 kernel: Code: 48 39 c8 73 30 80 3d 59 60 9d 00 00 41 bc f5 ff ff ff 0f 85 26 ff ff ff 48 c7 c7 b8 6b d0 92 c6 05 3f 60 9d 00 01 e8 24 3d ad ff <0f> ff 8b 53 64 e9 09 ff ff ff 65 48 8b 0c 25 00 d3 00 00 48 8b kernel: ---[ end trace c4cae366180e70ec ]--- kernel: as10x_usb: error during firmware upload part1 Let's allocate the the structure dynamically so we can get the firmware loaded correctly: [ 14.243057] as10x_usb: firmware: as102_data1_st.hex loaded with success [ 14.500777] as10x_usb: firmware: as102_data2_st.hex loaded with success Signed-off-by:
Michele Baldessari <michele@acksyn.org> Signed-off-by:
-
Naveen N. Rao authored
commit 46725b17 upstream. When a uprobe is installed on an instruction that we currently do not emulate, we copy the instruction into a xol buffer and single step that instruction. If that instruction generates a fault, we abort the single stepping before invoking the signal handler. Once the signal handler is done, the uprobe trap is hit again since the instruction is retried and the process repeats. We use uprobe_deny_signal() to detect if the xol instruction triggered a signal. If so, we clear TIF_SIGPENDING and set TIF_UPROBE so that the signal is not handled until after the single stepping is aborted. In this case, uprobe_deny_signal() returns true and get_signal() ends up returning 0. However, in do_signal(), we are not looking at the return value, but depending on ksig.sig for further action, all with an uninitialized ksig that is not touched in this scenario. Fix the same by initializing ksig.sig to 0. Fixes: 129b69df ("powerpc: Use get_signal() signal_setup_done()") Reported-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
John David Anglin authored
commit 05f016d2 upstream. As noted by Christoph Biedl, passing a pointer size of 4 in the new CAS implementation causes a kernel crash. The attached patch corrects the off by one error in the argument validity check. In reviewing the code, I noticed that we only perform word operations with the pointer size argument. The subi instruction intentionally uses a word condition on 64-bit kernels. Nullification was used instead of a cmpib instruction as the branch should never be taken. The shlw pseudo-operation generates a depw,z instruction and it clears the target before doing a shift left word deposit. Thus, we don't need to clip the upper 32 bits of this argument on 64-bit kernels. Tested with a gcc testsuite run with a 64-bit kernel. The gcc atomic code in libgcc is the only direct user of the new CAS implementation that I am aware of. Signed-off-by:
John David Anglin <dave.anglin@bell.net> Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Brian King authored
commit 0a9a17e3 upstream. This patch fixes an issue seen on Power systems with ixgbe which results in skb list corruption and an eventual kernel oops. The following is what was observed: CPU 1 CPU2 ============================ ============================ 1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq 2: first->skb = skb eop_desc = tx_buffer->next_to_watch 3: ixgbe_tx_map read_barrier_depends() 4: wmb check adapter written status bit 5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..); 6: writel(i, tx_ring->tail); The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not get loaded prior to tx_buffer->next_to_watch, which then results in loading a stale skb pointer. This patch replaces the read_barrier_depends with smp_rmb to ensure loads are ordered with respect to the load of tx_buffer->next_to_watch. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Acked-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
-
Brian King authored
commit 7b8edcc6 upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with fm10k as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by:
-
Brian King authored
commit f72271e2 upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with i40evf as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by:
-
Brian King authored
commit ae0c585d upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with ixgbevf as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by:
-
Brian King authored
commit 1e1f9ca5 upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with igbvf as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by:
-
Brian King authored
commit c4cb9918 upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with igb as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by:
-
Brian King authored
commit 52c6912f upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with i40e as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by:
-
Johan Hovold authored
commit c45e3e4c upstream. A recent change fixing NFC device allocation itself introduced an error-handling bug by returning an error pointer in case device-id allocation failed. This is clearly broken as the callers still expected NULL to be returned on errors as detected by Dan's static checker. Fix this up by returning NULL in the event that we've run out of memory when allocating a new device id. Note that the offending commit is marked for stable (3.8) so this fix needs to be backported along with it. Fixes: 20777bc5 ("NFC: fix broken device allocation") Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
-
Bart Van Assche authored
commit 8a0d18c6 upstream. This patch fixes the following kernel crash: general protection fault: 0000 [#1] PREEMPT SMP Workqueue: ib_mad2 timeout_sends [ib_core] Call Trace: ib_sa_path_rec_callback+0x1c4/0x1d0 [ib_core] send_handler+0xb2/0xd0 [ib_core] timeout_sends+0x14d/0x220 [ib_core] process_one_work+0x200/0x630 worker_thread+0x4e/0x3b0 kthread+0x113/0x150 Fixes: commit aef9ec39 ("IB: Add SCSI RDMA Protocol (SRP) initiator") Signed-off-by:
Bart Van Assche <bart.vanassche@wdc.com> Reviewed-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Bart Van Assche authored
commit c70ca389 upstream. Make srpt_parse_i_port_id() return a negative value if hex2bin() fails. Fixes: commit a42d985b ("ib_srpt: Initial SRP Target merge for v3.3-rc1") Signed-off-by:
-
Dan Williams authored
commit c1fb3542 upstream. For the same reason that /proc/iomem returns 0's for non-root readers and acpi tables are root-only, make the 'resource' attribute for namespace devices only readable by root. Otherwise we disclose physical address information. Fixes: bf9bccc1 ("libnvdimm: pmem label sets and namespace instantiation") Reported-by:
Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Dan Williams authored
commit b18d4b8a upstream. The set of valid sequence numbers is {1,2,3}. The specification indicates that an implementation should consider 0 a sign of a critical error: UEFI 2.7: 13.19 NVDIMM Label Protocol Software never writes the sequence number 00, so a correctly check-summed Index Block with this sequence number probably indicates a critical error. When software discovers this case it treats it as an invalid Index Block indication. While the expectation is that the invalid block is just thrown away, the Robustness Principle says we should fix this to make both sequence numbers valid. Fixes: f524bf27 ("libnvdimm: write pmem label set") Reported-by:
Juston Li <juston.li@intel.com> Signed-off-by:
-
Johan Hovold authored
commit 33ec6dbc upstream. Fix child node-lookup during probe, which ended up searching the whole device tree depth-first starting at parent rather than just matching on its children. Note that the original premature free of the parent node has already been fixed separately, but that fix was apparently never backported to stable. Fixes: 9ac33b0c ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)") Fixes: 660e1551 ("clk: ti: dra7-atl-clock: Fix of_node reference counting") Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
-
Peter Ujfalusi authored
commit 660e1551 upstream. of_find_node_by_name() will call of_node_put() on the node so we need to get it first to avoid warnings. The cfg_node needs to be put after we have finished processing the properties. Signed-off-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
-
Trond Myklebust authored
commit e9d4bf21 upstream. There is no guarantee that either the request or the svc_xprt exist by the time we get round to printing the trace message. Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Paolo Bonzini authored
commit 15038e14 upstream. For many years some users of assigned devices have reported worse performance on AMD processors with NPT than on AMD without NPT, Intel or bare metal. The reason turned out to be that SVM is discarding the guest PAT setting and uses the default (PA0=PA4=WB, PA1=PA5=WT, PA2=PA6=UC-, PA3=UC). The guest might be using a different setting, and especially might want write combining but isn't getting it (instead getting slow UC or UC- accesses). Thanks a lot to geoff@hostfission.com for noticing the relation to the g_pat setting. The patch has been tested also by a bunch of people on VFIO users forums. Fixes: 709ddebf Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196409Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Reviewed-by:
David Hildenbrand <david@redhat.com> Tested-by:
Nick Sarnie <commendsarnex@gmail.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Ladi Prosek authored
commit 21f2d551 upstream. Intel SDM 27.5.2 Loading Host Segment and Descriptor-Table Registers: "The GDTR and IDTR limits are each set to FFFFH." Signed-off-by:
Ladi Prosek <lprosek@redhat.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 1c79df1f upstream. This patch fixes a bug during QUEUE_FULL where transport_complete_qf() calls transport_complete_task_attr() after it's already been invoked by target_complete_ok_work() or transport_generic_request_failure() during initial completion, preceeding QUEUE_FULL. This will result in se_device->simple_cmds, se_device->dev_cur_ordered_id and/or se_device->dev_ordered_sync being updated multiple times for a single se_cmd. To address this bug, clear SCF_TASK_ATTR_SET after the first call to transport_complete_task_attr(), and avoid updating SCSI task attribute related counters for any subsequent calls. Also, when a se_cmd is deferred due to ordered tags and executed via target_restart_delayed_cmds(), set CMD_T_SENT before execution matching what target_execute_cmd() does. Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com> Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
