- 16 Feb, 2022 8 commits
-
-
Vladimir Oltean authored
The major user of replayed switchdev objects is DSA, and so far it hasn't needed information about anything other than bridge port VLANs, so this is all that br_switchdev_vlan_replay() knows to handle. DSA has managed to get by through replicating every VLAN addition on a user port such that the same VLAN is also added on all DSA and CPU ports, but there is a corner case where this does not work. The mv88e6xxx DSA driver currently prints this error message as soon as the first port of a switch joins a bridge: mv88e6085 0x0000000008b96000:00: port 0 failed to add a6:ef:77:c8:5f:3d vid 1 to fdb: -95 where a6:ef:77:c8:5f:3d vid 1 is a local FDB entry corresponding to the bridge MAC address in the default_pvid. The -EOPNOTSUPP is returned by mv88e6xxx_port_db_load_purge() because it tries to map VID 1 to a FID (the ATU is indexed by FID not VID), but fails to do so. This is because ->port_fdb_add() is called before ->port_vlan_add() for VID 1. The abridged timeline of the calls is: br_add_if -> netdev_master_upper_dev_link -> dsa_port_bridge_join -> switchdev_bridge_port_offload -> br_switchdev_vlan_replay (*) -> br_switchdev_fdb_replay -> mv88e6xxx_port_fdb_add -> nbp_vlan_init -> nbp_vlan_add -> mv88e6xxx_port_vlan_add and the issue is that at the time of (*), the bridge port isn't in VID 1 (nbp_vlan_init hasn't been called), therefore br_switchdev_vlan_replay() won't have anything to replay, therefore VID 1 won't be in the VTU by the time mv88e6xxx_port_fdb_add() is called. This happens only when the first port of a switch joins. For further ports, the initial mv88e6xxx_port_vlan_add() is sufficient for VID 1 to be loaded in the VTU (which is switch-wide, not per port). The problem is somewhat unique to mv88e6xxx by chance, because most other drivers offload an FDB entry by VID, so FDBs and VLANs can be added asynchronously with respect to each other, but addressing the issue at the bridge layer makes sense, since what mv88e6xxx requires isn't absurd. To fix this problem, we need to recognize that it isn't the VLAN group of the port that we're interested in, but the VLAN group of the bridge itself (so it isn't a timing issue, but rather insufficient information being passed from switchdev to drivers). As mentioned, currently nbp_switchdev_sync_objs() only calls br_switchdev_vlan_replay() for VLANs corresponding to the port, but the VLANs corresponding to the bridge itself, for local termination, also need to be replayed. In this case, VID 1 is not (yet) present in the port's VLAN group but is present in the bridge's VLAN group. So to fix this bug, DSA is now obligated to explicitly handle VLANs pointing towards the bridge in order to "close this race" (which isn't really a race). As Tobias Waldekranz notices, this also implies that it must explicitly handle port VLANs on foreign interfaces, something that worked implicitly before: https://patchwork.kernel.org/project/netdevbpf/patch/20220209213044.2353153-6-vladimir.oltean@nxp.com/#24735260 So in the end, br_switchdev_vlan_replay() must replay all VLANs from all VLAN groups: all the ports, and the bridge itself. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
There may be switchdev drivers that can add/remove a FDB or MDB entry only as long as the VLAN it's in has been notified and offloaded first. The nbp_switchdev_sync_objs() method satisfies this requirement on addition, but nbp_switchdev_unsync_objs() first deletes VLANs, then deletes MDBs and FDBs. Reverse the order of the function calls to cater to this requirement. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
br_switchdev_port_vlan_add() currently emits a SWITCHDEV_PORT_OBJ_ADD event with a SWITCHDEV_OBJ_ID_PORT_VLAN for 2 distinct cases: - a struct net_bridge_vlan got created - an existing struct net_bridge_vlan was modified This makes it impossible for switchdev drivers to properly balance PORT_OBJ_ADD with PORT_OBJ_DEL events, so if we want to allow that to happen, we must provide a way for drivers to distinguish between a VLAN with changed flags and a new one. Annotate struct switchdev_obj_port_vlan with a "bool changed" that distinguishes the 2 cases above. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
Currently, when a VLAN entry is added multiple times in a row to a bridge port, nbp_vlan_add() calls br_switchdev_port_vlan_add() each time, even if the VLAN already exists and nothing about it has changed: bridge vlan add dev lan12 vid 100 master static Similarly, when a VLAN is added multiple times in a row to a bridge, br_vlan_add_existing() doesn't filter at all the calls to br_switchdev_port_vlan_add(): bridge vlan add dev br0 vid 100 self This behavior makes driver-level accounting of VLANs impossible, since it is enough for a single deletion event to remove a VLAN, but the addition event can be emitted an unlimited number of times. The cause for this can be identified as follows: we rely on __vlan_add_flags() to retroactively tell us whether it has changed anything about the VLAN flags or VLAN group pvid. So we'd first have to call __vlan_add_flags() before calling br_switchdev_port_vlan_add(), in order to have access to the "bool *changed" information. But we don't want to change the event ordering, because we'd have to revert the struct net_bridge_vlan changes we've made if switchdev returns an error. So to solve this, we need another function that tells us whether any change is going to occur in the VLAN or VLAN group, _prior_ to calling __vlan_add_flags(). Split __vlan_add_flags() into a precommit and a commit stage, and rename it to __vlan_flags_update(). The precommit stage, __vlan_flags_would_change(), will determine whether there is any reason to notify switchdev due to a change of flags (note: the BRENTRY flag transition from false to true is treated separately: as a new switchdev entry, because we skipped notifying the master VLAN when it wasn't a brentry yet, and therefore not as a change of flags). With this lookahead/precommit function in place, we can avoid notifying switchdev if nothing changed for the VLAN and VLAN group. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
Currently there is a very subtle aspect to the behavior of __vlan_add_flags(): it changes the struct net_bridge_vlan flags and pvid, yet it returns true ("changed") even if none of those changed, just a transition of br_vlan_is_brentry(v) took place from false to true. This can be seen in br_vlan_add_existing(), however we do not actually rely on this subtle behavior, since the "if" condition that checks that the vlan wasn't a brentry before had a useless (until now) assignment: *changed = true; Make things more obvious by actually making __vlan_add_flags() do what's written on the box, and be more specific about what is actually written on the box. This is needed because further transformations will be done to __vlan_add_flags(). Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
When a VLAN is added to a bridge port and it doesn't exist on the bridge device yet, it gets created for the multicast context, but it is 'hidden', since it doesn't have the BRENTRY flag yet: ip link add br0 type bridge && ip link set swp0 master br0 bridge vlan add dev swp0 vid 100 # the master VLAN 100 gets created bridge vlan add dev br0 vid 100 self # that VLAN becomes brentry just now All switchdev drivers ignore switchdev notifiers for VLAN entries which have the BRENTRY unset, and for good reason: these are merely private data structures used by the bridge driver. So we might just as well not notify those at all. Cleanup in the switchdev drivers that check for the BRENTRY flag is now possible, and will be handled separately, since those checks just became dead code. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
When a VLAN is added to a bridge port, a master VLAN gets created on the bridge for context, but it doesn't have the BRENTRY flag. Then, when the same VLAN is added to the bridge itself, that enters through the br_vlan_add_existing() code path and gains the BRENTRY flag, thus it becomes "existing". It seems natural to check for this condition early, because the current code flow is to notify switchdev of the addition of a VLAN that isn't a brentry, just to delete it immediately afterwards. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Haiyue Wang authored
The commit a5886ef4 ("gve: Introduce per netdev `enum gve_queue_format`") introduces three queue format type, only GVE_GQI_QPL_FORMAT queue has page list. So it should use the queue page list number to detect the zero size queue page list. Correct the design logic. Using the 'queue_format == GVE_GQI_RDA_FORMAT' may lead to request zero sized memory allocation, like if the queue format is GVE_DQO_RDA_FORMAT. The kernel memory subsystem will return ZERO_SIZE_PTR, which is not NULL address, so the driver can run successfully. Also the code still checks the queue page list number firstly, then accesses the allocated memory, so zero number queue page list allocation will not lead to access fault. Signed-off-by: Haiyue Wang <haiyue.wang@intel.com> Reviewed-by: Bailey Forrest <bcf@google.com> Link: https://lore.kernel.org/r/20220215051751.260866-1-haiyue.wang@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
- 15 Feb, 2022 22 commits
-
-
Colin Ian King authored
There are spelling mistakes in debug messages. Fix them. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yang Li authored
Fix the following coccicheck warnings: ./drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:1199:42-47: WARNING: conversion to bool not needed here ./drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:1218:54-59: WARNING: conversion to bool not needed here Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
If the following call path returns an error from switchdev: nbp_vlan_flush -> __vlan_del -> __vlan_vid_del -> br_switchdev_port_vlan_del -> __vlan_group_free -> WARN_ON(!list_empty(&vg->vlan_list)); then the deletion of the net_bridge_vlan is silently halted, which will trigger the WARN_ON from __vlan_group_free(). The WARN_ON is rather unhelpful, because nothing about the source of the error is printed. Add a print to catch errors from __vlan_del. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christophe JAILLET authored
hso_create_device() is only called from function that already use GFP_KERNEL. And all the callers are called from the probe function. So there is no need here to explicitly require a GFP_ATOMIC when allocating memory. Use GFP_KERNEL instead. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Catanzaro authored
This patch fixes the checkpatch.pl warning: ERROR: code indent should use tabs where possible #3453: FILE: drivers/net/virtio_net.c:3453: ret = register_virtio_driver(&virtio_net_driver);$ Uneccessary newline was also removed making line 3453 now 3452. Signed-off-by: Michael Catanzaro <mcatanzaro.kernel@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5-updates-2022-02-14 mlx5 TX routines improvements 1) From Aya and Tariq, first 3 patches, Use the Max size of the TX descriptor as advertised by the device and not the fixed value of 16 that the driver always assumed, this is not a bug fix as all existing devices have Max value larger than 16, but the series is necessary for future proofing the driver. 2) TX Synchronization improvements from Maxim, last 12 patches Maxim Mikityanskiy Says: ======================= mlx5e: Synchronize ndo_select_queue with configuration changes The kernel can call ndo_select_queue at any time, and there is no direct way to block it. The implementation of ndo_select_queue in mlx5e expects the parameters to be consistent and may crash (invalid pointer, division by zero) if they aren't. There were attempts to partially fix some of the most frequent crashes, see commit 846d6da1 ("net/mlx5e: Fix division by 0 in mlx5e_select_queue") and commit 84c8a874 ("net/mlx5e: Fix division by 0 in mlx5e_select_queue for representors"). However, they don't address the issue completely. This series introduces the proper synchronization mechanism between mlx5e configuration and TX data path: 1. txq2sq updates are synchronized properly with ndo_start_xmit (mlx5e_xmit). The TX queue is stopped when it configuration is being updated, and memory barriers ensure the changes are visible before restarting. 2. The set of parameters needed for mlx5e_select_queue is reduced, and synchronization using RCU is implemented. This way, changes are atomic, and the state in mlx5e_select_queue is always consistent. 3. A few optimizations are applied to the new implementation of mlx5e_select_queue. ======================= ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Maxim Mikityanskiy authored
Check all booleans for special queues at once, when deciding whether to go to the fast path in mlx5e_select_queue. Pack them into bitfields to have some room for extensibility. Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Maxim Mikityanskiy authored
To improve the performance of the modulo operation (%), it's replaced by a subtracting the divisor in a loop. The modulo is used to fix up an out-of-bounds value that might be returned by netdev_pick_tx or to convert the queue number to the channel number when num_tcs > 1. Both situations are unlikely, because XPS is configured not to pick higher queues (qid >= num_channels) by default, so under normal circumstances the flow won't go inside the loop, and it will be faster than %. num_tcs == 8 adds at most 7 iterations to the loop. PTP adds at most 1 iteration to the loop. HTB would add at most 256 iterations (when num_channels == 1), so there is an additional boundary check in the HTB flow, which falls back to % if more than 7 iterations are expected. Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Maxim Mikityanskiy authored
This commit optimizes mlx5e_select_queue for HTB and PTP cases by short-cutting some checks, without sacrificing performance of the common non-HTB non-PTP flow. 1. The HTB flow uses the fact that num_tcs == 1 to drop these checks (it's not possible to attach both mqprio and htb as the root qdisc). It's also enough to calculate `txq_ix % num_channels` only once, instead of twice. 2. The PTP flow drops the check for HTB and the second calculation of `txq_ix % num_channels`. Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Maxim Mikityanskiy authored
trust_state can be written while mlx5e_select_queue() is reading it. To avoid inconsistencies, use READ_ONCE and WRITE_ONCE for access and updates, and touch the variable only once per operation. Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Maxim Mikityanskiy authored
Both mlx5e_select_queue and mlx5e_select_ptpsq contain the same logic to get user priority of a packet, according to the current trust state settings. This commit moves this repeating code to its own function. Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Maxim Mikityanskiy authored
Start using the select queue parameters introduced in the previous commit to have proper synchronization with changing the configuration (such as number of channels and queues). It ensures that the state that mlx5e_select_queue() sees is always consistent and stays the same while the function is running. Also it allows mlx5e_select_queue to stop using data structures that weren't synchronized properly: txq2sq, channel_tc2realtxq, port_ptp_tc2realtxq. The last two are removed completely, as they were used only in mlx5e_select_queue. Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Maxim Mikityanskiy authored
This commit moves mlx5e_select_queue and all stuff related to ndo_select_queue to en/selq.c to put all stuff working with selq into a separate file. Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Maxim Mikityanskiy authored
ndo_select_queue can be called at any time, and there is no way to stop the kernel from calling it to synchronize with configuration changes (real_num_tx_queues, num_tc). This commit introduces an internal way in mlx5e to sync mlx5e_select_queue() with these changes. The configuration needed by this function is stored in a struct mlx5e_selq_params, which is modified and accessed in an atomic way using RCU methods. The whole ndo_select_queue is called under an RCU lock, providing the necessary guarantees. The parameters stored in the new struct mlx5e_selq_params should only be used from inside mlx5e_select_queue. It's the minimal set of parameters needed for mlx5e_select_queue to do its job efficiently, derived from parameters stored elsewhere. That means that when the configuration change, mlx5e_selq_params may need to be updated. In such cases, the mlx5e_selq_prepare/mlx5e_selq_apply API should be used. struct mlx5e_selq contains two slots for the params: active and standby. mlx5e_selq_prepare updates the standby slot, and mlx5e_selq_apply swaps the slots in a safe atomic way using the RCU API. It integrates well with the open/activate stages of the configuration change flow. Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Maxim Mikityanskiy authored
This commit makes necessary changes to guarantee that txq2sq remains stable while mlx5e_xmit is running. Proper synchronization is added for HTB TX queues. All updates to txq2sq are performed while the corresponding queue is disabled (i.e. mlx5e_xmit doesn't run on that queue). smp_wmb after each change guarantees that mlx5e_xmit can see the updated value after the queue is enabled. Comments explaining this mechanism are added to mlx5e_xmit. When an HTB SQ can be deleted (after deleting an HTB node), synchronize with RCU to wait for mlx5e_select_queue to finish and stop selecting that queue, before we re-enable it to avoid TX timeout watchdog alarms. Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Maxim Mikityanskiy authored
mlx5e_build_txq_maps updates txq2sq while TX queues are stopped. Add a barrier to ensure that these changes are visible before the queues are started and mlx5e_xmit reads from txq2sq. This commit handles regular TX queues. Synchronization between HTB TX queues and mlx5e_xmit is handled in the following commit. Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Maxim Mikityanskiy authored
Normally, the queues are disabled when the channels are deactivated, and enabled when the channels are activated. However, on register, the channels are not active, but the queues are enabled by default. This change fixes it, preventing mlx5e_xmit from running when the channels are deactivated in the beginning. Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Maxim Mikityanskiy authored
mlx5e_activate_priv_channels() and mlx5e_deactivate_priv_channels() start and stop all netdev TX queues. This commit removes the unneeded call to netif_tx_stop_all_queues and adds explanatory comments why these operations are needed. netif_tx_disable() does the same thing that netif_tx_stop_all_queues(), but taking the TX lock, thus guaranteeing that ndo_start_xmit is not running after return. That means that the netif_tx_stop_all_queues() call is not really necessary. The comments are improved: the TX watchdog timeout explanation is moved to the start stage where it really belongs (it used to be in both places, but was lost during some old refactoring) and rephrased in more details; the explanation for stopping all TX queues is added. Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Aya Levin authored
Calculate maximal count of MPW WQEBBs on SQ's creation and store it there. Remove MLX5E_TX_MPW_MAX_NUM_DS and MLX5E_TX_MPW_MAX_WQEBBS. Update mlx5e_tx_mpwqe_is_full() and mlx5e_xdp_mpqwe_is_full() . Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Aya Levin authored
Prior to this patch the maximal value for max WQEBBs (WQE Basic Blocks, where WQE is a Work Queue Element) on the TX side was assumed to be 16 (fixed value). All firmware versions till today comply to this. In order to be more flexible and resilient, read from FW the corresponding: max_wqe_sz_sq. This value describes the maximum WQE size given in bytes, thus max WQEBBs is given by the division in WQEBB's byte size. The driver uses the top between 16 and the division result. This ensures synchronization between driver and firmware and avoids unexpected behavior. Store this value on the different SQs (Send Queues) for easy access. Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Tariq Toukan authored
Remove tstamp pointer in mlx5e_txqsq as it's no longer used after commit 7c39afb3 ("net/mlx5: PTP code migration to driver core section"). Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Aya Levin <ayal@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-
Tobias Waldekranz authored
These chips have 8 built-in FE PHYs and 3 SERDES interfaces that can run at 1G. With the blamed commit, the built-in PHYs could no longer be connected to, using an MII PHY interface mode. Create a separate .phylink_get_caps callback for these chips, which takes the FE/GE split into consideration. Fixes: 2ee84cfe ("net: dsa: mv88e6xxx: convert to phylink_generic_validate()") Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20220213185154.3262207-1-tobias@waldekranz.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
- 14 Feb, 2022 10 commits
-
-
Colin Ian King authored
There is a spelling mistake in an error message. Fix it. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Volodymyr Mytnyk authored
Add support of rule offloading added to the non-zero index chain, which was previously forbidden. Also, goto action is offloaded allowing to jump for processing of desired chain. Note that only implicit chain 0 is bound to the device port(s) for processing. The rest of chains have to be jumped by actions. Signed-off-by: Volodymyr Mytnyk <vmytnyk@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
M Chetan Kumar says: ==================== net: wwan: debugfs dev reference not dropped This patch series contains WWAN subsystem & IOSM Driver changes to drop dev reference obtained as part of wwan debugfs dir entry retrieval. PATCH1: A new debugfs interface is introduced in wwan subsystem so that wwan driver can drop the obtained dev reference post debugfs use. PATCH2: IOSM Driver uses new debugfs interface to drop dev reference. Please refer to commit messages for details. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
M Chetan Kumar authored
Post debugfs use call wwan_put_debugfs_dir()to drop debugfs dev reference. Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
M Chetan Kumar authored
WWAN driver call's wwan_get_debugfs_dir() to obtain WWAN debugfs dir entry. As part of this procedure it returns a reference to a found device. Since there is no debugfs interface available at WWAN subsystem, it is not possible to drop dev reference post debugfs use. This leads to side effects like post wwan driver load and reload the wwan instance gets increment from wwanX to wwanX+1. A new debugfs interface is added in wwan subsystem so that wwan driver can drop the obtained dev reference post debugfs use. void wwan_put_debugfs_dir(struct dentry *dir) Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Luiz Angelo Daros de Luca says: ==================== net: dsa: realtek: realtek-mdio: reset before setup This patch series cleans the realtek-smi reset code and copy that to the realtek-mdio. v1-v2) - do not run reset code block if GPIO is missing. It was printing "RESET deasserted" even when there is no GPIO configured. - reset switch after dsa_unregister_switch() - demote reset messages to debug v2-v3) - do not assert the reset on gpiod_get. Do it explicitly aferwards. - split the commit into two (one for each module) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Luiz Angelo Daros de Luca authored
Some devices, like the switch in Banana Pi BPI R64 only starts to answer after a HW reset. It is the same reset code from realtek-smi. Reported-by: Frank Wunderlich <frank-w@public-files.de> Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Tested-by: Frank Wunderlich <frank-w@public-files.de> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Luiz Angelo Daros de Luca authored
When reset GPIO was missing, the driver was still printing an info message and still trying to assert the reset. Although gpiod_set_value() will silently ignore calls with NULL gpio_desc, it is better to make it clear the driver might allow gpio_desc to be NULL. The initial value for the reset pin was changed to GPIOD_OUT_LOW, followed by a gpiod_set_value() asserting the reset. This way, it will be easier to spot if and where the reset really happens. A new "asserted RESET" message was added just after the reset is asserted, similar to the existing "deasserted RESET" message. Both messages were demoted to dbg. The code comment is not needed anymore. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Whenever rt6_uncached_list_flush_dev() swaps rt->rt6_idev to the blackhole device, parts of IPv6 stack might still need to increment one SNMP counter. Root cause, patch from Ido, changelog from Eric :) This bug suggests that we need to audit rt->rt6_idev usages and make sure they are properly using RCU protection. Fixes: e5f80fcf ("ipv6: give an IPv6 dev to blackhole_netdev") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Luiz Angelo Daros de Luca authored
The macro was missed while renaming realtek-smi.h to realtek.h. Fixes: f5f11907 (net: dsa: realtek: rename realtek_smi to) Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-