When calling start/stop_ap(), mac80211 already has a protected
link_conf pointer. Pass it to the driver, so it shouldn't
handle RCU protection.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Refactor the element parsing into a version that has
a parameter struct so we can add more parameters more
easily in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Extend the cfg80211_rx_assoc_resp() to cover multiple
BSSes, the AP MLD address and local link addresses
for MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For MLO we'll need a lot more arguments, including all the
BSS pointers and link addresses, so move the data to a struct
to be able to extend it more easily later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

We only report the BSSID to userspace, so change the
argument from BSS struct pointer to AP address, which
we'll use to carry either the BSSID or AP MLD address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There are a few cases where we send an event to cfg80211
manually, but ieee80211_destroy_assoc_data() also handles
the case of abandoning; some cases don't need an event
and success is handled yet differently.

Unify this by providing a single status argument to the
ieee80211_destroy_assoc_data() function and then handling
all the different cases of events (or no events) there.

This will help simplify the code when MLO support is
added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For MLO, we need the ability to report back multiple BSS
structures to release, as well as the AP MLD address (if
attempting to make an MLO connection).

Unify cfg80211_assoc_timeout() and cfg80211_abandon_assoc()
into a new cfg80211_assoc_failure() that gets a structure
parameter with the necessary data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The race described by the comment in mac80211 hasn't existed
since the locking rework to use the same lock and for MLO we
need to pass the AP MLD address, so just pass the BSSID or
AP MLD address instead of the BSS struct pointer, and adjust
all the code accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For station capabilities, e.g. TWT, we need to use the correct
link station instead of deflink. Switch the code to do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The argument is unused except for NULL checking, but we already
do that anyway, so it's not needed. Remove the argument.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This requires a few more changes.

While at it, also add a warning to ieee80211_get_sband()
to avoid it being used when there are multiple links.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If we decide to stop tracking QoS/WMM parameters, then
this should be a per-link decision. Move the flag to
the link instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Do the first adjustments in the client-side code to pass
the link pointer (instead of sdata) to most places etc.

This is just preparation, so the real MLO patches become
smaller.

Note that this isn't complete, notably there are still
quite a few references to sta->deflink and sta->sta.deflink.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Remove the IEEE80211_STA_RESET_SIGNAL_AVE flag and use
a bool instead, but invert the polarity (now calling it
tracking_signal_avg) so we don't have to initialize it,
and put that into the link instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

To prepare a bit more for MLO in the client code,
track the AP's address (for now only the BSSID, but
will track the AP MLD's address later) separately
from the per-link BSSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This variable is only written to, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Take the link into account in the QoS settings (EDCA parameters)
APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In MLO, expect the driver fully handles powersave handling,
including tracking whether or not a beacon was received,
the DTIM period, etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This really shouldn't be in a per-link config, we don't want
to let anyone control it that way (if anything, link powersave
could be forced through APIs to activate/deactivate a link),
and we don't support powersave in software with devices that
can do MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

It might be useful to drivers to be able to pass only the
link_conf pointer, rather than both the pointer and the
link_id; add the link_id to the link_conf to facility that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In station/client mode, the link data needs a bit more
initialization and destruction than just zero-init and
kfree() respectively, implement that.

This required some shuffling of the link data handling
in general, as we should set it up in setup and do the
teardown in teardown, otherwise we're asymmetric in
case of interface type changes.

Also stop using kfree_rcu(), we cannot guarantee that
nothing is scheduling things that live within the link
(e.g. the u.mgd.request_smps_work) until we're sure it
cannot be referenced anymore, therefore synchronize
instead. This isn't very efficient, but we can always
optimize it later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This function can be static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

At least the quantenna driver calls wdev_chandef() here
which now requires the lock, so acquire it.

Fixes: 7b0a0e3c ("wifi: cfg80211: do some rework towards MLO link APIs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

With the split into keys[]/deflink.gtk[] arrays, WEP keys are
still installed into the keys[] array, but we didn't look them
up there. This meant they weren't deleted correctly.

Fix this by looking up the key there even if it's not pairwise
so we can be sure we don't have it.

Fixes: bfd8403a ("wifi: mac80211: reorg some iface data structs for MLD")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Separate out the connection downgrade flags from the ifmgd->flags
and put them into the link information instead. While at it, make
them a separate sparse type so we don't get confused about where
they belong and have static checking on correct handling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Align the mac80211 implementation with P802.11be_D2.0.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Align the mac80211 implementation with P802.11be_D1.5.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There are a few places that check ps_sdata and/or the dynamic
PS timeout, but they're erroneous in case SUPPORTS_DYNAMIC_PS
is set by the driver.

Skip the entire recalculation in this case so we cannot get
into those paths elsewhere, and so we simplify this for the
purpose of implementing MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If we don't really have multiple links, omit the link ID from
link debug prints, otherwise we change the format for all of
the existing drivers (most of which might never support MLO),
and also have extra noise in the logs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Do address matching with link addresses as well.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For multi-link operation, this cannot work as the req->bss pointer
will be NULL, and we'll need to do more work on this to really add
tracing for the MLO case here. Drop the BSS elements for now as
they're not the most useful thing, and it's hard to size things
correctly for the MLO case (without adding a lot of code that's
also executed when tracing isn't enabled.)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

We might assign -1 to it in some cases when key is NULL,
which means the key_idx isn't used but can lead to a
warning from static checkers such as smatch.

Make the struct member signed simply to avoid that, we
only need a range of -1..3 anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since for an MLD station the default link is added together
with the add station command, allow also setting the link
MAC address.
Otherwise, it is needed to use the modify link API only
for setting the link MAC address.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since links can be added and removed dynamically, we need to
somehow protect the sdata->link[] and vif->link_conf[] array
pointers from disappearing when accessing them without locks.
RCU-ify the pointers to achieve this, which requires quite a
bit of rework.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since this will need to refer - at least in part - to the link
stations of an MLD, hold the wdev mutex for driver convenience.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since we deal with links in an MLD here, hold the wdev
mutex now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since we deal with links, and that requires looking at wdev links,
we should hold the wdev mutex for driver convenience.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Implement callbacks for cfg80211 add_link_station, mod_link_station,
and del_link_station API.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Put the link_station_parameters structure in the station_parameters
structure (and remove the station_parameters fields already existing
in link_station_parameters).
Now, for an MLD station, the default link is added together with
the station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add an API for adding/modifying/removing a link of a station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>