The PCI shutdown handler is invoked in response
to system reboot or shutdown. A data transfer
might still be in flight when this happens. So
the very first action we take here is to send
a link down notification, so that any pending
data transfer is terminated. Rest of the actions
are same as that of PCI remove handler.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

When the driver on the local side is loaded, it sets
SIDE_READY bit in SIDE_INFO register. Likewise, when
it is un-loaded, it clears the bit.

Also just after being loaded, the driver polls for
peer SIDE_READY bit to be set. Since that bit is set
when the peer side driver has loaded, the polling on
local side breaks as soon as this condition is met.

But the situation is different when the driver is
un-loaded. Since the polling has already been stopped
as mentioned before, if the peer side driver gets
un-loaded, the driver on the local side is not notified
implicitly.

So, we improvise using existing doorbell mechanism.
We reserve the highest order bit of the DB register to
send a notification to peer when the driver on local
side is un-loaded. This also means that now we are one
short of 16 DB events and that is taken care of in the
valid DB mask.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

db_valid_mask is set at two places, once within
amd_init_ntb(), and again within amd_init_dev().
Since amd_init_ntb() is actually called from
amd_init_dev(), setting db_valid_mask from
former does not really make sense. So remove it.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Since NTB connects two physically separate systems,
there can be scenarios where one system goes down
while the other one remains active. In case of NTB
primary, if the NTB secondary goes down, a Link-Down
event is received. For the NTB secondary, if the
NTB primary goes down, the PCIe hotplug mechanism
ensures that the driver on the secondary side is also
unloaded.

But there are other scenarios to consider as well,
when suppose the physical link remains active, but
the driver on primary or secondary side is loaded
or un-loaded.

When the driver is loaded, on either side, it sets
SIDE_READY bit(bit-1) of SIDE_INFO register. Similarly,
when the driver is un-loaded, it resets the same bit.

We consider the NTB link to be up and operational
only when the driver on both sides of link are loaded
and ready. But we also need to take account of
Link Up and Down events which signify the physical
link status. So amd_link_is_up() is modified to take
care of the above scenarios.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

We define two new helper functions to set and clear
sideinfo registers respectively. These functions
take an additional boolean parameter which signifies
whether we want to set/clear the sideinfo register
of the peer(true) or local host(false).
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

It does not really make sense to enable or disable
the bits of NTB_CTRL register only during enable
and disable link callbacks. They should be done
independent of these callbacks. The correct placement
for that is during the amd_init_side_info() and
amd_deinit_side_info() functions, which are invoked
during probe and remove respectively.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Just like for Link-Down event, Link-Up and D3 events
are also mutually exclusive to Link-Down and D0 events
respectively. So we clear the bitmasks in peer_sta
depending on event type.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Link-Up and Link-Down are mutually exclusive events.
So when we receive a Link-Down event, we should also
clear the bitmask for Link-Up event in peer_sta.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

amd_link_is_up() is a callback to inquire whether
the NTB link is up or not. So it should not indulge
itself into clearing the bitmasks of peer_sta.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

amd_ack_smu() should only set the corresponding
bits into SMUACK register. Setting the bitmask
of peer_sta should be done within the event handler.
They are two different things, and so should be
handled differently and at different places.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Bit 1 of SIDE_INFO register is an indication that
the driver on the other side of link is ready. We
set this bit during driver initialization sequence.
So rather than having separate macros to return the
status, we can simply return the status of this bit
from amd_poll_link(). So a return of 1 or 0 from
this function will indicate to the caller whether
the driver on the other side of link is ready or not,
respectively.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Since getting the status of link is a logically separate
operation, we simply create a new function which will
store the link status to be used later.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Link-Up and Link-Down events can occur irrespective
of whether a data transfer is in progress or not.
So we need to enable the interrupt delivery for
these events early during driver load.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

The interrupt status register should be cleared
by driver once the particular event is handled.
The patch fixes this.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

The design of AMD NTB implementation is such that
NTB primary acts as an endpoint device and NTB
secondary is an endpoint device behind a combination
of Switch Upstream and Switch Downstream. Considering
that, the link status and control register needs to
be accessed differently based on the NTB topology.

So in the case of NTB secondary, we first get the
pointer to the Switch Downstream device for the NTB
device. Then we get the pointer to the Switch Upstream
device. Once we have that, we read the Link Status
and Control register to get the correct status of
link at the secondary.

In the case of NTB primary, simply reading the Link
Status and Control register of the NTB device itself
will suffice.
Suggested-by: Jiasen Lin <linjiasen@hygon.cn>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

updating with my email address.
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit.  Fix it by replacing with scnprintf().

Fixes: fce8a7bb (PCI-Express Non-Transparent Bridge Support)
Fixes: 282a2fee (NTB: Use DMA Engine to Transmit and Receive)
Fixes: a754a8fc (NTB: allocate number transport entries depending on size of ring size)
Fixes: d98ef99e (NTB: Clean up QP stats info)
Fixes: e74bfeed (NTB: Add flow control to the ntb_netdev)
Fixes: 569410ca (NTB: Use unique DMA channels for TX and RX)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

ntb_mw_set_trans() should work as ntb_mw_clear_trans() when size == 0 and/or
addr == 0. But error in xlate_pos checking condition prevents this.
Fix the condition to make ntb_mw_clear_trans() working.

Fixes: 87d11e64 (NTB: switchtec_ntb: Add memory window support)
Signed-off-by: Alexander Fomichev <fomichev.ru@gmail.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

The correct printk format is %pa or %pap, but not %pa[p].

Fixes: 7f46c8b3 ("NTB: ntb_tool: Add full multi-port NTB API support")
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

peer->outbuf is a virtual address which is get by ioremap, it can not
be converted to a physical address by virt_to_page and page_to_phys.
This conversion will result in DMA error, because the destination address
which is converted by page_to_phys is invalid.

This patch save the MMIO address of NTB BARx in perf_setup_peer_mw,
and map the BAR space to DMA address after we assign the DMA channel.
Then fill the destination address of DMA descriptor with this DMA address
to guarantee that the address of memory write requests fall into
memory window of NBT BARx with IOMMU enabled and disabled.

Fixes: 5648e56d ("NTB: ntb_perf: Add full multi-port NTB API support")
Signed-off-by: Jiasen Lin <linjiasen@hygon.cn>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

The offset of PCIe Capability Header for AMD and HYGON NTB is 0x64,
but the macro which named "AMD_LINK_STATUS_OFFSET" is defined as 0x68.
It is offset of Device Capabilities Reg rather than Link Control Reg.

This code trigger an error in get link statsus:

	cat /sys/kernel/debug/ntb_hw_amd/0000:43:00.1/info
		LNK STA -               0x8fa1
		Link Status -           Up
		Link Speed -            PCI-E Gen 0
		Link Width -            x0

This patch use pcie_capability_read_dword to get link status.
After fix this issue, we can get link status accurately:

	cat /sys/kernel/debug/ntb_hw_amd/0000:43:00.1/info
		LNK STA -               0x11030042
		Link Status -           Up
		Link Speed -            PCI-E Gen 3
		Link Width -            x16

Fixes: a1b36958 ("NTB: Add support for AMD PCI-Express Non-Transparent Bridge")
Signed-off-by: Jiasen Lin <linjiasen@hygon.cn>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Pull more Kbuild updates from Masahiro Yamada:

 - fix randconfig to generate a sane .config

 - rename hostprogs-y / always to hostprogs / always-y, which are more
   natual syntax.

 - optimize scripts/kallsyms

 - fix yes2modconfig and mod2yesconfig

 - make multiple directory targets ('make foo/ bar/') work

* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: make multiple directory targets work
  kconfig: Invalidate all symbols after changing to y or m.
  kallsyms: fix type of kallsyms_token_table[]
  scripts/kallsyms: change table to store (strcut sym_entry *)
  scripts/kallsyms: rename local variables in read_symbol()
  kbuild: rename hostprogs-y/always to hostprogs/always-y
  kbuild: fix the document to use extra-y for vmlinux.lds
  kconfig: fix broken dependency in randconfig-generated .config

Pull new zonefs file system from Damien Le Moal:
 "Zonefs is a very simple file system exposing each zone of a zoned
  block device as a file.

  Unlike a regular file system with native zoned block device support
  (e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
  sequential write constraint of zoned block devices to the user. As a
  result, zonefs is not a POSIX compliant file system. Its goal is to
  simplify the implementation of zoned block devices support in
  applications by replacing raw block device file accesses with a richer
  file based API, avoiding relying on direct block device file ioctls
  which may be more obscure to developers.

  One example of this approach is the implementation of LSM
  (log-structured merge) tree structures (such as used in RocksDB and
  LevelDB) on zoned block devices by allowing SSTables to be stored in a
  zone file similarly to a regular file system rather than as a range of
  sectors of a zoned device. The introduction of the higher level
  construct "one file is one zone" can help reducing the amount of
  changes needed in the application while at the same time allowing the
  use of zoned block devices with various programming languages other
  than C.

  Zonefs IO management implementation uses the new iomap generic code.
  Zonefs has been successfully tested using a functional test suite
  (available with zonefs userland format tool on github) and a prototype
  implementation of LevelDB on top of zonefs"

* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
  zonefs: Add documentation
  fs: New zonefs file system

In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.

Fixes: 4e6437f1 ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull cifs fixes from Steve French:
 "13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:

   - Important fix for multichannel and for modefromsid mounts.

   - Two reconnect fixes

   - Addition of SMB3 change notify support

   - Backup tools fix

   - A few additional minor debug improvements (tracepoints and
     additional logging found useful during testing this week)"

* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: Add defines for new information level, FileIdInformation
  smb3: print warning once if posix context returned on open
  smb3: add one more dynamic tracepoint missing from strict fsync path
  cifs: fix mode bits from dir listing when mounted with modefromsid
  cifs: fix channel signing
  cifs: add SMB3 change notification support
  cifs: make multichannel warning more visible
  cifs: fix soft mounts hanging in the reconnect code
  cifs: Add tracepoints for errors on flush or fsync
  cifs: log warning message (once) if out of disk space
  cifs: fail i/o on soft mounts if sessionsetup errors out
  smb3: fix problem with null cifs super block with previous patch
  SMB3: Backup intent flag missing from some more ops

Pull vboxfs from Al Viro:
 "This is the VirtualBox guest shared folder support by Hans de Goede,
  with fixups for fs_parse folded in to avoid bisection hazards from
  those API changes..."

* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: Add VirtualBox guest shared folder (vboxsf) support

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes for X86:

   - Ensure that the PIT is set up when the local APIC is disable or
     configured in legacy mode. This is caused by an ordering issue
     introduced in the recent changes which skip PIT initialization when
     the TSC and APIC frequencies are already known.

   - Handle malformed SRAT tables during early ACPI parsing which caused
     an infinite loop anda boot hang.

   - Fix a long standing race in the affinity setting code which affects
     PCI devices with non-maskable MSI interrupts. The problem is caused
     by the non-atomic writes of the MSI address (destination APIC id)
     and data (vector) fields which the device uses to construct the MSI
     message. The non-atomic writes are mandated by PCI.

     If both fields change and the device raises an interrupt after
     writing address and before writing data, then the MSI block
     constructs a inconsistent message which causes interrupts to be
     lost and subsequent malfunction of the device.

     The fix is to redirect the interrupt to the new vector on the
     current CPU first and then switch it over to the new target CPU.
     This allows to observe an eventually raised interrupt in the
     transitional stage (old CPU, new vector) to be observed in the APIC
     IRR and retriggered on the new target CPU and the new vector.

     The potential spurious interrupts caused by this are harmless and
     can in the worst case expose a buggy driver (all handlers have to
     be able to deal with spurious interrupts as they can and do happen
     for various reasons).

   - Add the missing suspend/resume mechanism for the HYPERV hypercall
     page which prevents resume hibernation on HYPERV guests. This
     change got lost before the merge window.

   - Mask the IOAPIC before disabling the local APIC to prevent
     potentially stale IOAPIC remote IRR bits which cause stale
     interrupt lines after resume"

* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic: Mask IOAPIC entries when disabling the local APIC
  x86/hyperv: Suspend/resume the hypercall page for hibernation
  x86/apic/msi: Plug non-maskable MSI affinity race
  x86/boot: Handle malformed SRAT tables during early ACPI parsing
  x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode

Pull SMP fixes from Thomas Gleixner:
 "Two fixes for the SMP related functionality:

   - Make the UP version of smp_call_function_single() match SMP
     semantics when called for a not available CPU. Instead of emitting
     a warning and assuming that the function call target is CPU0,
     return a proper error code like the SMP version does.

   - Remove a superfluous check in smp_call_function_many_cond()"

* tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  smp/up: Make smp_call_function_single() match SMP semantics
  smp: Remove superfluous cond_func check in smp_call_function_many_cond()

Pull perf fixes from Thomas Gleixner:
 "A set of fixes and improvements for the perf subsystem:

  Kernel fixes:

   - Install cgroup events to the correct CPU context to prevent a
     potential list double add

   - Prevent an integer underflow in the perf mlock accounting

   - Add a missing prototype for arch_perf_update_userpage()

  Tooling:

   - Add a missing unlock in the error path of maps__insert() in perf
     maps.

   - Fix the build with the latest libbfd

   - Fix the perf parser so it does not delete parse event terms, which
     caused a regression for using perf with the ARM CoreSight as the
     sink configuration was missing due to the deletion.

   - Fix the double free in the perf CPU map merging test case

   - Add the missing ustring support for the perf probe command"

* tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf maps: Add missing unlock to maps__insert() error case
  perf probe: Add ustring support for perf probe command
  perf: Make perf able to build with latest libbfd
  perf test: Fix test case Merge cpu map
  perf parse: Copy string to perf_evsel_config_term
  perf parse: Refactor 'struct perf_evsel_config_term'
  kernel/events: Add a missing prototype for arch_perf_update_userpage()
  perf/cgroups: Install cgroup events to correct cpuctx
  perf/core: Fix mlock accounting in perf_mmap()

Pull timer fixes from Thomas Gleixner:
 "Two small fixes for the time(r) subsystem:

   - Handle a subtle race between the clocksource watchdog and a
     concurrent clocksource watchdog stop/start sequence correctly to
     prevent a timer double add bug.

   - Fix the file path for the core time namespace file"

* tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: Prevent double add_timer_on() for watchdog_timer
  MAINTAINERS: Correct path to time namespace source file

Pull interrupt fixes from Thomas Gleixner:
 "A set of fixes for the interrupt subsystem:

   - Provision only ACPI enabled redistributors on GICv3

   - Use the proper command colums when building the INVALL command for
     the GICv3-ITS

   - Ensure the allocation of the L2 vPE table for GICv4.1

   - Correct the GICv4.1 VPROBASER programming so it uses the proper
     size

   - A set of small GICv4.1 tidy up patches

   - Configuration cleanup for C-SKY interrupt chip

   - Clarify the function documentation for irq_set_wake() to document
     that the wakeup functionality is orthogonal to the irq
     disable/enable mechanism"

* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
  irqchip/gic-v3-its: Remove superfluous WARN_ON
  irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
  irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
  irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
  irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
  genirq: Clarify that irq wake state is orthogonal to enable/disable
  irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
  irqchip: Some Kconfig cleanup for C-SKY
  irqchip/gic-v3: Only provision redistributors that are enabled in ACPI

Pull EFI fix from Thomas Gleixner:
 "A single fix for a EFI boot regression on X86 which was caused by the
  recent rework of the EFI memory map parsing. On systems with invalid
  memmap entries the cleanup function uses an value which cannot be
  relied on in this stage. Use the actual EFI memmap entry instead"

* tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/x86: Fix boot regression on systems with invalid memmap entries

Pull misc SCSI fixes from James Bottomley:
 "Five small patches, all in drivers or doc, which missed the initial
  pull request.

  The qla2xxx and megaraid_sas are actual fixes and the rest are
  spelling and doc changes"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: fix spelling mistake "initilized" -> "initialized"
  scsi: pm80xx: fix spelling mistake "to" -> "too"
  scsi: MAINTAINERS: ufs: remove pedrom.sousa@synopsys.com
  scsi: megaraid_sas: fixup MSIx interrupt setup during resume
  scsi: qla2xxx: Fix unbound NVME response length

Pull networking fixes from David Miller:

 1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.

 2) Fix thermal zone registration in iwlwifi, from Andrei
    Otcheretianski.

 3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.

 4) Use after free in mptcp, from Florian Westphal.

 5) Use after free in wireguard's root_remove_peer_lists, from Eric
    Dumazet.

 6) Properly access packets heads in bonding alb code, from Eric
    Dumazet.

 7) Fix data race in skb_queue_len(), from Qian Cai.

 8) Fix regression in r8169 on some chips, from Heiner Kallweit.

 9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.

10) Certain kinds of set link netlink operations can cause a NULL deref
    in the ipv6 addrconf code. Fix from Eric Dumazet.

11) Don't cancel uninitialized work queue in drop monitor, from Ido
    Schimmel.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  net: thunderx: use proper interface type for RGMII
  mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
  bpf: Improve bucket_log calculation logic
  selftests/bpf: Test freeing sockmap/sockhash with a socket in it
  bpf, sockhash: Synchronize_rcu before free'ing map
  bpf, sockmap: Don't sleep while holding RCU lock on tear-down
  bpftool: Don't crash on missing xlated program instructions
  bpf, sockmap: Check update requirements after locking
  drop_monitor: Do not cancel uninitialized work item
  mlxsw: spectrum_dpipe: Add missing error path
  mlxsw: core: Add validation of hardware device types for MGPIR register
  mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
  selftests: mlxsw: Add test cases for local table route replacement
  mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
  net: dsa: microchip: enable module autoprobe
  ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
  dpaa_eth: support all modes with rate adapting PHYs
  net: stmmac: update pci platform data to use phy_interface
  net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
  net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
  ...

VirtualBox hosts can share folders with guests, this commit adds a
VFS driver implementing the Linux-guest side of this, allowing folders
exported by the host to be mounted under Linux.

This driver depends on the guest <-> host IPC functions exported by
the vboxguest driver.
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull powerpc fixes from Michael Ellerman:

 - Fix an existing bug in our user access handling, exposed by one of
   the bug fixes we merged this cycle.

 - A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the
   recently added CONFIG_VMAP_STACK.

Thanks to: Christophe Leroy, Guenter Roeck.

* tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
  powerpc/futex: Fix incorrect user access blocking

This is a merge error on my part - the driver was merged into mainline
by commit c5951e7c ("Merge tag 'mips_5.6' of git://../mips/linux")
over a week ago, but nobody apparently noticed that it didn't actually
build due to still having a reference to the devm_ioremap_nocache()
function, removed a few days earlier through commit 6a1000bd ("Merge
tag 'ioremap-5.6' of git://../ioremap").

Apparently this didn't get any build testing anywhere.  Not perhaps all
that surprising: it's restricted to 64-bit MIPS only, and only with the
new SGI_MFD_IOC3 support enabled.

I only noticed because the ioremap conflicts in the ARM SoC driver
update made me check there weren't any others hiding, and I found this
one.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC late updates from Olof Johansson:
 "This is some material that we picked up into our tree late, or that
  had more complex dependencies on more than one topic branch that makes
  sense to keep separately.

   - TI support for secure accelerators and hwrng on OMAP4/5

   - TI camera changes for dra7 and am437x and SGX improvement due to
     better reset control support on am335x, am437x and dra7

   - Davinci moves to proper clocksource on DM365, and regulator/audio
     improvements for DM365 and DM644x eval boards"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
  ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
  ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
  ARM: dts: Configure interconnect target module for am437x sgx
  ARM: dts: Configure sgx for dra7
  ARM: dts: Configure rstctrl reset for am335x SGX
  ARM: dts: dra7: Add ti-sysc node for VPE
  ARM: dts: dra7: add vpe clkctrl node
  ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
  ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
  ARM: dts: am43xx: add support for clkout1 clock
  arm: dts: dra76-evm: Add CAL and OV5640 nodes
  arm: dtsi: dra76x: Add CAL dtsi node
  arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
  ARM: dts: DRA72: Add CAL dtsi node
  ARM: dts: dra7-l4: Add ti-sysc node for CAM
  ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
  ARM: dts: dra7: add cam clkctrl node
  ARM: OMAP2+: Drop legacy platform data for omap4 des
  ARM: OMAP2+: Drop legacy platform data for omap4 sham
  ARM: OMAP2+: Drop legacy platform data for omap4 aes
  ...

Pull ARM SoC defconfig updates from Olof Johansson:
 "We keep this in a separate branch to avoid cross-branch conflicts, but
  most of the material here is fairly boring -- some new drivers turned
  on for hardware since they were merged, and some refreshed files due
  to time having moved a lot of entries around"

* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
  ARM: configs: at91: enable MMC_SDHCI_OF_AT91 and MICROCHIP_PIT64B
  arm64: defconfig: Enable Broadcom's GENET Ethernet controller
  ARM: multi_v7_defconfig: Enable devfreq thermal integration
  ARM: exynos_defconfig: Enable devfreq thermal integration
  ARM: multi_v7_defconfig: Enable NFS v4.1 and v4.2
  ARM: exynos_defconfig: Enable NFS v4.1 and v4.2
  arm64: defconfig: Enable Actions Semi specific drivers
  arm64: defconfig: Enable Broadcom's STB PCIe controller
  arm64: defconfig: Enable CONFIG_CLK_IMX8MP by default
  ARM: configs: at91: enable config flags for sam9x60 SoC
  ARM: configs: at91: use savedefconfig
  arm64: defconfig: Enable tegra XUDC support
  ARM: defconfig: gemini: Update defconfig
  arm64: defconfig: enable CONFIG_ARM_QCOM_CPUFREQ_NVMEM
  arm64: defconfig: enable CONFIG_QCOM_CPR
  arm64: defconfig: Enable HFPLL
  arm64: defconfig: Enable CRYPTO_DEV_FSL_CAAM
  ARM: imx_v6_v7_defconfig: Select the TFP410 driver
  ARM: imx_v6_v7_defconfig: Enable NFS_V4_1 and NFS_V4_2 support
  arm64: defconfig: Enable ATH10K_SNOC
  ...