- 16 Jan, 2023 25 commits
-
-
Bitterblue Smith authored
The wifi + bluetooth combo chip RTL8723BU can leak memory (especially?) when it's connected to a bluetooth audio device. The busy bluetooth traffic generates lots of C2H (card to host) messages, which are not freed correctly. To fix this, move the dev_kfree_skb() call in rtl8xxxu_c2hcmd_callback() inside the loop where skb_dequeue() is called. The RTL8192EU leaks memory because the C2H messages are added to the queue and left there forever. (This was fine in the past because it probably wasn't sending any C2H messages until commit e542e66b ("wifi: rtl8xxxu: gen2: Turn on the rate control"). Since that commit it sends a C2H message when the TX rate changes.) To fix this, delete the check for rf_paths > 1 and the goto. Let the function process the C2H messages from RTL8192EU like the ones from the other chips. Theoretically the RTL8188FU could also leak like RTL8723BU, but it most likely doesn't send C2H messages frequently enough. This change was tested with RTL8723BU by Erhard F. I tested it with RTL8188FU and RTL8192EU. Reported-by:
Erhard F. <erhard_f@mailbox.org> Tested-by:
Bitterblue Smith <rtl8821cerfe2@gmail.com> Reviewed-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/03b099c1-c671-d252-36f4-57b70d721f9d@gmail.com
-
Zong-Zhe Yang authored
The configurations, wde_qempty_acq_num and wde_qempty_mgq_sel, are used when MAC checks if TX queues are empty. Fill the corresponding setting for 8852B. Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
-
Zong-Zhe Yang authored
TX BD's RAM table describes how HW allocates usable buffer section for each TX channel at fetch time. The total RAM size for TX BD is chip-dependent. For 8852BE, it has only half size (32) for TX channels of single band. Original table arrange total size (64) for dual band. It will overflow on 8852BE circuit and cause section conflicts between different TX channels. So, we do the changes below. * add another table for single band chip and export both kind of tables * point to the expected one in rtw89_pci_info by chip Signed-off-by:
-
Chih-Kang Chang authored
Some hardware modules don't have good RF characteristic as regular. It could get ADC abnormal in low temperature, and it causes bad RX performance and affects calibration result of DPK. Signed-off-by:
Chih-Kang Chang <gary.chang@realtek.com> Signed-off-by:
-
Eric Huang authored
This change fixes the precision of CFO and TX EVM, and it could imporve performance in some cases. Also, use the correctted definition for 8852A. Signed-off-by:
Eric Huang <echuang@realtek.com> Signed-off-by:
-
Kuan-Chung Chen authored
The mac_id of management frames should follow rtwvif->mac_id or rtwsta->mac_id. Add this patch to set the correct mac_id and prevent unexpected behavior. Signed-off-by:
Kuan-Chung Chen <damon.chen@realtek.com> Signed-off-by:
-
Kuan-Chung Chen authored
When transmitting a packet that gets from ieee80211_nullfunc_get(), the vif in tx_info->control was no assigned, which will cause dereferencing a null pointer. Signed-off-by:
-
Ching-Te Ku authored
The Wi-Fi role info structure will need to H2C to firmware, firmware need these information to do some multi-role operation. v1 add DBCC and NOA information in the structure. And driver side also need to put/get values at the corresponding version of structure. Signed-off-by:
Ching-Te Ku <ku920601@realtek.com> Signed-off-by:
-
Ching-Te Ku authored
RTL8852B support the new features like TDMA instant (Change TDMA mechanism immediately), Co-RX feature (Wi-Fi/Bluetooth can RX in the same time) and so on. The v1 TDMA policy will enable those newer mechanism. It will have a better coexistence performance. Signed-off-by:
-
Ching-Te Ku authored
Because the difference of the hardware design, RTL8852C can not get the PTA owner by the same method with RTL8852B, RTL8852A. Modify the get owner API and related logic. Signed-off-by:
-
Ching-Te Ku authored
Slot list is to list the WiFi/Bluetooth PTA hardware priority setting. Move the list parser to its function, not to append together with TDMA parser. Signed-off-by:
-
Ching-Te Ku authored
The report records the slots/events and their time cost about the code call flow at firmware, ver 3 assign a reserved variable to recognize the report is enabled or not. And add corresponding function to parsing the report. Signed-off-by:
-
Ching-Te Ku authored
Coexistence need to send Null data to stop AP keeps TX packet to DUT before DUT coexistence switch to Bluetooth time slot, or it will be an interference to DUT BT and because DUT will not RX packet from AP the packet retry may harmful to WL TP. Compare to v1 version, the newer firmware report will also report Null TX data counter. Signed-off-by:
-
Ching-Te Ku authored
The newer Wi-Fi firmware are all changed to "Not to send H2C to mention firmware how many call flow step should firmware trace". The structure had removed the member, and define the steps number at newer version firmware. Signed-off-by:
-
Jiasheng Jiang authored
Add check for the return value of alloc_workqueue since it may return NULL pointer. Moreover, add destroy_workqueue when rtw89_load_firmware fails. Fixes: e3ec7017 ("rtw89: add Realtek 802.11ax driver") Signed-off-by:
Jiasheng Jiang <jiasheng@iscas.ac.cn> Acked-by:
Leon Romanovsky <leonro@nvidia.com> Signed-off-by:
-
Zong-Zhe Yang authored
Do `kfree_skb(new)` before `goto out` to prevent potential leak. Fixes: 89590777 ("rtw89: 8852a: add ieee80211_ops::hw_scan") Signed-off-by:
-
Ching-Te Ku authored
Change style to feature version separate. And because there are different WiFi roles number in the firmware, it will make structure length longer or shorter, so update the length calculator to cover the difference. Signed-off-by:
-
Ching-Te Ku authored
Only when firmware control report version is 1, need to get the counter by reading the register. The other version will monitor the counter at firmware. And upstream branch only RTL8852A has this old version. Signed-off-by:
-
Ching-Te Ku authored
Comparing v5 control report to v4 version, v5 reduce some of variable's size to reduce firmware code size. And change the grant signal report format. Signed-off-by:
-
Ching-Te Ku authored
The rtw89 driver may support more than 1 version of Wi-Fi firmware for certain chips. In order to support all the firmware, change to select logic by firmware feature version code. Type control version 4 will monitor Bluetooth PTA hardware counters at firmware and C2H to driver, but version 1 will not do this. Signed-off-by:
-
Ching-Te Ku authored
To support v4 version firmware cycle report, apply the related structure and functions. v4 cycle report add a group of status to show how the free-run/TDMA training goes to. It is a firmware mechanism that can auto adjust coexistence mode between TDMA and free run mechanism at 3 antenna solution. Signed-off-by:
-
Ching-Te Ku authored
Because there are new report format in the upcoming patches, to make the logic more readable, rename the related structure by their version number. And to support the several version at the same time, add union definition to include all the versions. Signed-off-by:
-
Ching-Te Ku authored
There are at least 2 version of cycle report format. If the code keep translating the report to local variable, the numbers of variable in check btc report function will out of maximum variable numbers. And most of these variable are using only one time, it is not necessary to store at memory. Signed-off-by:
-
Masanari Iida authored
This patch fixes a spelling typo in debug message. Signed-off-by:
Masanari Iida <standby24x7@gmail.com> Acked-by:
-
Jisoo Jang authored
Fix a stack-out-of-bounds read in brcmfmac that occurs when 'buf' that is not null-terminated is passed as an argument of strreplace() in brcmf_c_preinit_dcmds(). This buffer is filled with a CLM version string by memcpy() in brcmf_fil_iovar_data_get(). Ensure buf is null-terminated. Found by a modified version of syzkaller. [ 33.004414][ T1896] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available [ 33.013486][ T1896] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43236/3 wl0: Nov 30 2011 17:33:42 version 5.90.188.22 [ 33.021554][ T1896] ================================================================== [ 33.022379][ T1896] BUG: KASAN: stack-out-of-bounds in strreplace+0xf2/0x110 [ 33.023122][ T1896] Read of size 1 at addr ffffc90001d6efc8 by task kworker/0:2/1896 [ 33.023852][ T1896] [ 33.024096][ T1896] CPU: 0 PID: 1896 Comm: kworker/0:2 Tainted: G O 5.14.0+ #132 [ 33.024927][ T1896] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 33.026065][ T1896] Workqueue: usb_hub_wq hub_event [ 33.026581][ T1896] Call Trace: [ 33.026896][ T1896] dump_stack_lvl+0x57/0x7d [ 33.027372][ T1896] print_address_description.constprop.0.cold+0xf/0x334 [ 33.028037][ T1896] ? strreplace+0xf2/0x110 [ 33.028403][ T1896] ? strreplace+0xf2/0x110 [ 33.028807][ T1896] kasan_report.cold+0x83/0xdf [ 33.029283][ T1896] ? strreplace+0xf2/0x110 [ 33.029666][ T1896] strreplace+0xf2/0x110 [ 33.029966][ T1896] brcmf_c_preinit_dcmds+0xab1/0xc40 [ 33.030351][ T1896] ? brcmf_c_set_joinpref_default+0x100/0x100 [ 33.030787][ T1896] ? rcu_read_lock_sched_held+0xa1/0xd0 [ 33.031223][ T1896] ? rcu_read_lock_bh_held+0xb0/0xb0 [ 33.031661][ T1896] ? lock_acquire+0x19d/0x4e0 [ 33.032091][ T1896] ? find_held_lock+0x2d/0x110 [ 33.032605][ T1896] ? brcmf_usb_deq+0x1a7/0x260 [ 33.033087][ T1896] ? brcmf_usb_rx_fill_all+0x5a/0xf0 [ 33.033582][ T1896] brcmf_attach+0x246/0xd40 [ 33.034022][ T1896] ? wiphy_new_nm+0x1476/0x1d50 [ 33.034383][ T1896] ? kmemdup+0x30/0x40 [ 33.034722][ T1896] brcmf_usb_probe+0x12de/0x1690 [ 33.035223][ T1896] ? brcmf_usbdev_qinit.constprop.0+0x470/0x470 [ 33.035833][ T1896] usb_probe_interface+0x25f/0x710 [ 33.036315][ T1896] really_probe+0x1be/0xa90 [ 33.036656][ T1896] __driver_probe_device+0x2ab/0x460 [ 33.037026][ T1896] ? usb_match_id.part.0+0x88/0xc0 [ 33.037383][ T1896] driver_probe_device+0x49/0x120 [ 33.037790][ T1896] __device_attach_driver+0x18a/0x250 [ 33.038300][ T1896] ? driver_allows_async_probing+0x120/0x120 [ 33.038986][ T1896] bus_for_each_drv+0x123/0x1a0 [ 33.039906][ T1896] ? bus_rescan_devices+0x20/0x20 [ 33.041412][ T1896] ? lockdep_hardirqs_on_prepare+0x273/0x3e0 [ 33.041861][ T1896] ? trace_hardirqs_on+0x1c/0x120 [ 33.042330][ T1896] __device_attach+0x207/0x330 [ 33.042664][ T1896] ? device_bind_driver+0xb0/0xb0 [ 33.043026][ T1896] ? kobject_uevent_env+0x230/0x12c0 [ 33.043515][ T1896] bus_probe_device+0x1a2/0x260 [ 33.043914][ T1896] device_add+0xa61/0x1ce0 [ 33.044227][ T1896] ? __mutex_unlock_slowpath+0xe7/0x660 [ 33.044891][ T1896] ? __fw_devlink_link_to_suppliers+0x550/0x550 [ 33.045531][ T1896] usb_set_configuration+0x984/0x1770 [ 33.046051][ T1896] ? kernfs_create_link+0x175/0x230 [ 33.046548][ T1896] usb_generic_driver_probe+0x69/0x90 [ 33.046931][ T1896] usb_probe_device+0x9c/0x220 [ 33.047434][ T1896] really_probe+0x1be/0xa90 [ 33.047760][ T1896] __driver_probe_device+0x2ab/0x460 [ 33.048134][ T1896] driver_probe_device+0x49/0x120 [ 33.048516][ T1896] __device_attach_driver+0x18a/0x250 [ 33.048910][ T1896] ? driver_allows_async_probing+0x120/0x120 [ 33.049437][ T1896] bus_for_each_drv+0x123/0x1a0 [ 33.049814][ T1896] ? bus_rescan_devices+0x20/0x20 [ 33.050164][ T1896] ? lockdep_hardirqs_on_prepare+0x273/0x3e0 [ 33.050579][ T1896] ? trace_hardirqs_on+0x1c/0x120 [ 33.050936][ T1896] __device_attach+0x207/0x330 [ 33.051399][ T1896] ? device_bind_driver+0xb0/0xb0 [ 33.051888][ T1896] ? kobject_uevent_env+0x230/0x12c0 [ 33.052314][ T1896] bus_probe_device+0x1a2/0x260 [ 33.052688][ T1896] device_add+0xa61/0x1ce0 [ 33.053121][ T1896] ? __fw_devlink_link_to_suppliers+0x550/0x550 [ 33.053568][ T1896] usb_new_device.cold+0x463/0xf66 [ 33.053953][ T1896] ? hub_disconnect+0x400/0x400 [ 33.054313][ T1896] ? rwlock_bug.part.0+0x90/0x90 [ 33.054661][ T1896] ? lockdep_hardirqs_on_prepare+0x273/0x3e0 [ 33.055094][ T1896] hub_event+0x10d5/0x3330 [ 33.055530][ T1896] ? hub_port_debounce+0x280/0x280 [ 33.055934][ T1896] ? __lock_acquire+0x1671/0x5790 [ 33.056387][ T1896] ? wq_calc_node_cpumask+0x170/0x2a0 [ 33.056924][ T1896] ? lock_release+0x640/0x640 [ 33.057383][ T1896] ? rcu_read_lock_sched_held+0xa1/0xd0 [ 33.057916][ T1896] ? rcu_read_lock_bh_held+0xb0/0xb0 [ 33.058402][ T1896] ? lockdep_hardirqs_on_prepare+0x273/0x3e0 [ 33.059019][ T1896] process_one_work+0x873/0x13e0 [ 33.059488][ T1896] ? lock_release+0x640/0x640 [ 33.059932][ T1896] ? pwq_dec_nr_in_flight+0x320/0x320 [ 33.060446][ T1896] ? rwlock_bug.part.0+0x90/0x90 [ 33.060898][ T1896] worker_thread+0x8b/0xd10 [ 33.061348][ T1896] ? __kthread_parkme+0xd9/0x1d0 [ 33.061810][ T1896] ? process_one_work+0x13e0/0x13e0 [ 33.062288][ T1896] kthread+0x379/0x450 [ 33.062660][ T1896] ? _raw_spin_unlock_irq+0x24/0x30 [ 33.063148][ T1896] ? set_kthread_struct+0x100/0x100 [ 33.063606][ T1896] ret_from_fork+0x1f/0x30 [ 33.064070][ T1896] [ 33.064313][ T1896] [ 33.064545][ T1896] addr ffffc90001d6efc8 is located in stack of task kworker/0:2/1896 at offset 512 in frame: [ 33.065478][ T1896] brcmf_c_preinit_dcmds+0x0/0xc40 [ 33.065973][ T1896] [ 33.066191][ T1896] this frame has 4 objects: [ 33.066614][ T1896] [48, 56) 'ptr' [ 33.066618][ T1896] [80, 148) 'revinfo' [ 33.066957][ T1896] [192, 210) 'eventmask' [ 33.067338][ T1896] [256, 512) 'buf' [ 33.067742][ T1896] [ 33.068304][ T1896] Memory state around the buggy address: [ 33.068838][ T1896] ffffc90001d6ee80: f2 00 00 02 f2 f2 f2 f2 f2 00 00 00 00 00 00 00 [ 33.069545][ T1896] ffffc90001d6ef00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 33.070626][ T1896] >ffffc90001d6ef80: 00 00 00 00 00 00 00 00 00 f3 f3 f3 f3 f3 f3 f3 [ 33.072052][ T1896] ^ [ 33.073043][ T1896] ffffc90001d6f000: f3 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 33.074230][ T1896] ffffc90001d6f080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 33.074914][ T1896] ================================================================== [ 33.075713][ T1896] Disabling lock debugging due to kernel taint Reviewed-by: Arend van Spriel<arend.vanspriel@broadcom.com> Signed-off-by:
Jisoo Jang <jisoo.jang@yonsei.ac.kr> Signed-off-by:
-
- 12 Jan, 2023 4 commits
-
-
Philipp Zabel authored
Allow probing rfkill-gpio via device tree. This hooks up the already existing support that was started in commit 262c91ee ("net: rfkill: gpio: prepare for DT and ACPI support") via the "rfkill-gpio" compatible, with the "name" and "type" properties renamed to "label" and "radio-type", respectively, in the device tree case. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Link: https://lore.kernel.org/r/20230102-rfkill-gpio-dt-v2-2-d1b83758c16d@pengutronix.deSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Philipp Zabel authored
Add a device tree binding document for GPIO controlled rfkill switches. The label and radio-type properties correspond to the name and type properties used for ACPI, respectively. The shutdown-gpios property is the same as defined for ACPI. Signed-off-by:
Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20230102-rfkill-gpio-dt-v2-1-d1b83758c16d@pengutronix.deSigned-off-by:
-
Nick Hainke authored
Remove a space in "the frames". Signed-off-by:
Nick Hainke <vincent@systemli.org> Link: https://lore.kernel.org/r/20221222092957.870790-1-vincent@systemli.orgSigned-off-by:
-
Martin Blumenstingl authored
This reverts commit acb99b9b ("mac80211: Add stations iterator where the iterator function may sleep"). A different approach was found for the rtw88 driver where most of the problematic locks were converted to a driver-local mutex. Drop ieee80211_iterate_stations() because there are no users of that function. Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20221226191609.2934234-1-martin.blumenstingl@googlemail.comSigned-off-by:
-
- 22 Dec, 2022 11 commits
-
-
Yang Yingliang authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile tested only. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Signed-off-by:
-
Yang Yingliang authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile tested only. Fixes: f52b041a ("libertas: Add spinlock to avoid race condition") Signed-off-by:
-
Yang Yingliang authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile tested only. Fixes: d2e7b342 ("libertas: disable functionality when interface is down") Signed-off-by:
-
Yang Yingliang authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile tested only. Fixes: a3128fee ("libertas: use irqsave() in USB's complete callback") Signed-off-by:
-
Yang Yingliang authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile tested only. Fixes: fc75122f ("libertas_tf: use irqsave() in USB's complete callback") Signed-off-by:
-
Zhengchao Shao authored
After the DMA buffer is mapped to a physical address, address is stored in pktids in brcmf_msgbuf_alloc_pktid(). Then, pktids is parsed in brcmf_msgbuf_get_pktid()/brcmf_msgbuf_release_array() to obtain physaddr and later unmap the DMA buffer. But when count is always equal to pktids->array_size, physaddr isn't stored in pktids and the DMA buffer will not be unmapped anyway. Fixes: 9a1bb602 ("brcmfmac: Adding msgbuf protocol.") Signed-off-by:
Zhengchao Shao <shaozhengchao@huawei.com> Reviewed-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
Zhang Changzhong authored
The brcmf_netdev_start_xmit() returns NETDEV_TX_OK without freeing skb in case of pskb_expand_head() fails, add dev_kfree_skb() to fix it. Compile tested only. Fixes: 270a6c1f ("brcmfmac: rework headroom check in .start_xmit()") Signed-off-by:
Zhang Changzhong <zhangchangzhong@huawei.com> Reviewed-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
-
Jisoo Jang authored
This patch fixes a stack-out-of-bounds read in brcmfmac that occurs when 'buf' that is not null-terminated is passed as an argument of strsep() in brcmf_c_preinit_dcmds(). This buffer is filled with a firmware version string by memcpy() in brcmf_fil_iovar_data_get(). The patch ensures buf is null-terminated. Found by a modified version of syzkaller. [ 47.569679][ T1897] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43236b for chip BCM43236/3 [ 47.582839][ T1897] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available [ 47.601565][ T1897] ================================================================== [ 47.602574][ T1897] BUG: KASAN: stack-out-of-bounds in strsep+0x1b2/0x1f0 [ 47.603447][ T1897] Read of size 1 at addr ffffc90001f6f000 by task kworker/0:2/1897 [ 47.604336][ T1897] [ 47.604621][ T1897] CPU: 0 PID: 1897 Comm: kworker/0:2 Tainted: G O 5.14.0+ #131 [ 47.605617][ T1897] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 47.606907][ T1897] Workqueue: usb_hub_wq hub_event [ 47.607453][ T1897] Call Trace: [ 47.607801][ T1897] dump_stack_lvl+0x8e/0xd1 [ 47.608295][ T1897] print_address_description.constprop.0.cold+0xf/0x334 [ 47.609009][ T1897] ? strsep+0x1b2/0x1f0 [ 47.609434][ T1897] ? strsep+0x1b2/0x1f0 [ 47.609863][ T1897] kasan_report.cold+0x83/0xdf [ 47.610366][ T1897] ? strsep+0x1b2/0x1f0 [ 47.610882][ T1897] strsep+0x1b2/0x1f0 [ 47.611300][ T1897] ? brcmf_fil_iovar_data_get+0x3a/0xf0 [ 47.611883][ T1897] brcmf_c_preinit_dcmds+0x995/0xc40 [ 47.612434][ T1897] ? brcmf_c_set_joinpref_default+0x100/0x100 [ 47.613078][ T1897] ? rcu_read_lock_sched_held+0xa1/0xd0 [ 47.613662][ T1897] ? rcu_read_lock_bh_held+0xb0/0xb0 [ 47.614208][ T1897] ? lock_acquire+0x19d/0x4e0 [ 47.614704][ T1897] ? find_held_lock+0x2d/0x110 [ 47.615236][ T1897] ? brcmf_usb_deq+0x1a7/0x260 [ 47.615741][ T1897] ? brcmf_usb_rx_fill_all+0x5a/0xf0 [ 47.616288][ T1897] brcmf_attach+0x246/0xd40 [ 47.616758][ T1897] ? wiphy_new_nm+0x1703/0x1dd0 [ 47.617280][ T1897] ? kmemdup+0x43/0x50 [ 47.617720][ T1897] brcmf_usb_probe+0x12de/0x1690 [ 47.618244][ T1897] ? brcmf_usbdev_qinit.constprop.0+0x470/0x470 [ 47.618901][ T1897] usb_probe_interface+0x2aa/0x760 [ 47.619429][ T1897] ? usb_probe_device+0x250/0x250 [ 47.619950][ T1897] really_probe+0x205/0xb70 [ 47.620435][ T1897] ? driver_allows_async_probing+0x130/0x130 [ 47.621048][ T1897] __driver_probe_device+0x311/0x4b0 [ 47.621595][ T1897] ? driver_allows_async_probing+0x130/0x130 [ 47.622209][ T1897] driver_probe_device+0x4e/0x150 [ 47.622739][ T1897] __device_attach_driver+0x1cc/0x2a0 [ 47.623287][ T1897] bus_for_each_drv+0x156/0x1d0 [ 47.623796][ T1897] ? bus_rescan_devices+0x30/0x30 [ 47.624309][ T1897] ? lockdep_hardirqs_on_prepare+0x273/0x3e0 [ 47.624907][ T1897] ? trace_hardirqs_on+0x46/0x160 [ 47.625437][ T1897] __device_attach+0x23f/0x3a0 [ 47.625924][ T1897] ? device_bind_driver+0xd0/0xd0 [ 47.626433][ T1897] ? kobject_uevent_env+0x287/0x14b0 [ 47.627057][ T1897] bus_probe_device+0x1da/0x290 [ 47.627557][ T1897] device_add+0xb7b/0x1eb0 [ 47.628027][ T1897] ? wait_for_completion+0x290/0x290 [ 47.628593][ T1897] ? __fw_devlink_link_to_suppliers+0x5a0/0x5a0 [ 47.629249][ T1897] usb_set_configuration+0xf59/0x16f0 [ 47.629829][ T1897] usb_generic_driver_probe+0x82/0xa0 [ 47.630385][ T1897] usb_probe_device+0xbb/0x250 [ 47.630927][ T1897] ? usb_suspend+0x590/0x590 [ 47.631397][ T1897] really_probe+0x205/0xb70 [ 47.631855][ T1897] ? driver_allows_async_probing+0x130/0x130 [ 47.632469][ T1897] __driver_probe_device+0x311/0x4b0 [ 47.633002][ T1897] ? usb_generic_driver_match+0x75/0x90 [ 47.633573][ T1897] ? driver_allows_async_probing+0x130/0x130 [ 47.634170][ T1897] driver_probe_device+0x4e/0x150 [ 47.634703][ T1897] __device_attach_driver+0x1cc/0x2a0 [ 47.635248][ T1897] bus_for_each_drv+0x156/0x1d0 [ 47.635748][ T1897] ? bus_rescan_devices+0x30/0x30 [ 47.636271][ T1897] ? lockdep_hardirqs_on_prepare+0x273/0x3e0 [ 47.636881][ T1897] ? trace_hardirqs_on+0x46/0x160 [ 47.637396][ T1897] __device_attach+0x23f/0x3a0 [ 47.637904][ T1897] ? device_bind_driver+0xd0/0xd0 [ 47.638426][ T1897] ? kobject_uevent_env+0x287/0x14b0 [ 47.638985][ T1897] bus_probe_device+0x1da/0x290 [ 47.639512][ T1897] device_add+0xb7b/0x1eb0 [ 47.639977][ T1897] ? __fw_devlink_link_to_suppliers+0x5a0/0x5a0 [ 47.640612][ T1897] ? kfree+0x14a/0x6b0 [ 47.641055][ T1897] ? __usb_get_extra_descriptor+0x116/0x160 [ 47.641679][ T1897] usb_new_device.cold+0x49c/0x1029 [ 47.642245][ T1897] ? hub_disconnect+0x450/0x450 [ 47.642756][ T1897] ? rwlock_bug.part.0+0x90/0x90 [ 47.643273][ T1897] ? _raw_spin_unlock_irq+0x24/0x30 [ 47.643822][ T1897] ? lockdep_hardirqs_on_prepare+0x273/0x3e0 [ 47.644445][ T1897] hub_event+0x1c98/0x3950 [ 47.644939][ T1897] ? hub_port_debounce+0x2e0/0x2e0 [ 47.645467][ T1897] ? check_irq_usage+0x861/0xf20 [ 47.645975][ T1897] ? drain_workqueue+0x280/0x360 [ 47.646506][ T1897] ? lock_release+0x640/0x640 [ 47.646994][ T1897] ? rcu_read_lock_sched_held+0xa1/0xd0 [ 47.647572][ T1897] ? rcu_read_lock_bh_held+0xb0/0xb0 [ 47.648111][ T1897] ? lockdep_hardirqs_on_prepare+0x273/0x3e0 [ 47.648735][ T1897] process_one_work+0x92b/0x1460 [ 47.649262][ T1897] ? pwq_dec_nr_in_flight+0x330/0x330 [ 47.649816][ T1897] ? rwlock_bug.part.0+0x90/0x90 [ 47.650336][ T1897] worker_thread+0x95/0xe00 [ 47.650830][ T1897] ? __kthread_parkme+0x115/0x1e0 [ 47.651361][ T1897] ? process_one_work+0x1460/0x1460 [ 47.651904][ T1897] kthread+0x3a1/0x480 [ 47.652329][ T1897] ? set_kthread_struct+0x120/0x120 [ 47.652878][ T1897] ret_from_fork+0x1f/0x30 [ 47.653370][ T1897] [ 47.653608][ T1897] [ 47.653848][ T1897] addr ffffc90001f6f000 is located in stack of task kworker/0:2/1897 at offset 512 in frame: [ 47.654891][ T1897] brcmf_c_preinit_dcmds+0x0/0xc40 [ 47.655442][ T1897] [ 47.655690][ T1897] this frame has 4 objects: [ 47.656151][ T1897] [48, 56) 'ptr' [ 47.656159][ T1897] [80, 148) 'revinfo' [ 47.656534][ T1897] [192, 210) 'eventmask' [ 47.656953][ T1897] [256, 512) 'buf' [ 47.657410][ T1897] [ 47.658035][ T1897] Memory state around the buggy address: [ 47.658743][ T1897] ffffc90001f6ef00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 47.659577][ T1897] ffffc90001f6ef80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 47.660394][ T1897] >ffffc90001f6f000: f3 f3 f3 f3 f3 f3 f3 f3 00 00 00 00 00 00 00 00 [ 47.661199][ T1897] ^ [ 47.661625][ T1897] ffffc90001f6f080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 47.662455][ T1897] ffffc90001f6f100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1 [ 47.663318][ T1897] ================================================================== [ 47.664147][ T1897] Disabling lock debugging due to kernel taint Reported-by:
Dokyung Song <dokyungs@yonsei.ac.kr> Reported-by:
Minsuk Kang <linuxlovemin@yonsei.ac.kr> Signed-off-by:
-
Wang Yufen authored
Fault injection test reports this issue: kernel BUG at net/core/dev.c:10731! invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI Call Trace: <TASK> wilc_netdev_ifc_init+0x19f/0x220 [wilc1000 884bf126e9e98af6a708f266a8dffd53f99e4bf5] wilc_cfg80211_init+0x30c/0x380 [wilc1000 884bf126e9e98af6a708f266a8dffd53f99e4bf5] wilc_bus_probe+0xad/0x2b0 [wilc1000_spi 1520a7539b6589cc6cde2ae826a523a33f8bacff] spi_probe+0xe4/0x140 really_probe+0x17e/0x3f0 __driver_probe_device+0xe3/0x170 driver_probe_device+0x49/0x120 The root case here is alloc_ordered_workqueue() fails, but cfg80211_unregister_netdevice() or unregister_netdev() not be called in error handling path. To fix add unregister_netdev goto lable to add the unregister operation in error handling path. Fixes: 09ed8bfc ("wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"") Signed-off-by:
Wang Yufen <wangyufen@huawei.com> Signed-off-by:
-
Zhang Changzhong authored
The wilc_mac_xmit() returns NETDEV_TX_OK without freeing skb, add dev_kfree_skb() to fix it. Compile tested only. Fixes: c5c77ba1 ("staging: wilc1000: Add SDIO/SPI 802.11 driver") Signed-off-by:
-
Zhengchao Shao authored
In the error path of ipw_wdev_init(), exception value is returned, and the memory applied for in the function is not released. Also the memory is not released in ipw_pci_probe(). As a result, memory leakage occurs. So memory release needs to be added to the error path of ipw_wdev_init(). Fixes: a3caa99e ("libipw: initiate cfg80211 API conversion (v2)") Signed-off-by:
-
