- 27 Jun, 2019 40 commits
-
-
Vladimir Oltean authored
A FDB entry means that "frames that match this VID and DMAC must be forwarded to this port". In the case of dsa_8021q however, the VID is not a single one (and neither two, as my previous patch assumed). The VID can be set either by the CPU port (1 tx_vid), or by any of the other front-panel port (n-1 rx_vid's). Fixes: 93647594 ("net: dsa: sja1105: Hide the dsa_8021q VLANs from the bridge fdb command") Signed-off-by:
Vladimir Oltean <olteanv@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
The reason why this wasn't tackled earlier is that I had hoped I understood the user manual wrong. But unfortunately hacks are required in order to retrieve the static/dynamic nature of FDB entries on SJA1105 P/Q/R/S, since this info is stored in the writeback buffer of the dynamic config command. Signed-off-by:
-
Vladimir Oltean authored
When trying to add support for LOCKEDS (static FDB entries) on SJA1105 P/Q/R/S, at first I didn't remember how the abstraction I created worked, and actually thought it works by mistake. To avoid other people staring at the code and not making much sense out of it, add some comments at the top of the file. Signed-off-by:
-
Vladimir Oltean authored
After commit 8456721d ("net: dsa: sja1105: Add support for configuring address ageing time"), we started to reset the switch rather often (each time the bridge core changes the ageing time on a switch port). The unfortunate reality is that SJA1105 doesn't have any {cold, warm, whatever} reset mode in which it accepts a new configuration stream without flushing the FDB. Instead, in its world, the FDB *is* an optional part of the static configuration. So we play its game, and do what we also do for VLANs: for each 'bridge fdb' command, we add the FDB entry through the dynamic interface, and we append the in-kernel static config memory with info that we're going to use later, when the next reset command is going to be issued. The result is that 'bridge fdb' commands are now persistent (dynamically learned entries are lost, but that's ok). Signed-off-by:
-
Vladimir Oltean authored
At the end of the commit 1da73821 ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series") message, I said that: At the moment only FDB entries installed statically through 'bridge fdb' are visible in the dump callback - the dynamically learned ones are still under investigation. It looks like the reason why they were not visible in 'bridge fdb' was that they were never learned - always flooded. SJA1105 P/Q/R/S manual says about the MAXADDRP[port] field: Specify the maximum number of MAC address dynamically learned from the respective port. It is used to limit the number of learned MAC addresses per port. It looks like not providing a value in the static config (aka providing zeroes) is enough for it to not store the learned addresses in the FDB. For now we divide the 1024 entry FDB "equally" amongst the 5 ports. This may be revisited if the situation calls for that - for now I'm happy that learning works. Signed-off-by:
-
Vladimir Oltean authored
In commit 1da73821 ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series"), these bits were set in the static config, but apparently they did not do anything. The reason is that the packing accessors for them were part of a patch I forgot to send. Signed-off-by:
-
Vladimir Oltean authored
In SJA1105 there is no concept of 'default values' per se, everything needs to be driver-supplied through the static configuration tables. The issue is that the hardware manual says that 'at least the default untagging VLAN' is mandatory to be provided through the static config. But VLAN 0 isn't a very good initial pvid - its use is reserved for priority-tagged frames, and the layers of the stack that care about those already make sure that this VLAN is installed, as can be seen in the message below: 8021q: adding VLAN 0 to HW filter on device swp2 So change the pvid provided through the static configuration to 1, which matches the bridge core's defaults. Signed-off-by:
-
Vladimir Oltean authored
Currently when the driver unloads and PTP is enabled, the delayed work that prevents the timecounter from expiring becomes a ticking time bomb. The kernel will schedule the work thread within 60 seconds of driver removal, but the work handler is no longer there, leading to this strange and inconclusive stack trace: [ 64.473112] Unable to handle kernel paging request at virtual address 79746970 [ 64.480340] pgd = 008c4af9 [ 64.483042] [79746970] *pgd=00000000 [ 64.486620] Internal error: Oops: 80000005 [#1] SMP ARM [ 64.491820] Modules linked in: [ 64.494871] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.2.0-rc5-01634-ge3a2773ba9e5 #1246 [ 64.503007] Hardware name: Freescale LS1021A [ 64.507259] PC is at 0x79746970 [ 64.510393] LR is at call_timer_fn+0x3c/0x18c [ 64.514729] pc : [<79746970>] lr : [<c03bd734>] psr: 60010113 [ 64.520965] sp : c1901de0 ip : 00000000 fp : c1903080 [ 64.526163] r10: c1901e38 r9 : ffffe000 r8 : c19064ac [ 64.531363] r7 : 79746972 r6 : e98dd260 r5 : 00000100 r4 : c1a9e4a0 [ 64.537859] r3 : c1900000 r2 : ffffa400 r1 : 79746972 r0 : e98dd260 [ 64.544359] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none [ 64.551460] Control: 10c5387d Table: a8a2806a DAC: 00000051 [ 64.557176] Process swapper/0 (pid: 0, stack limit = 0x1ddb27f0) [ 64.563147] Stack: (0xc1901de0 to 0xc1902000) [ 64.567481] 1de0: eb6a4918 3d60d7c3 c1a9e554 e98dd260 eb6a34c0 c1a9e4a0 ffffa400 c19064ac [ 64.575616] 1e00: ffffe000 c03bd95c c1901e34 c1901e34 eb6a34c0 c1901e30 c1903d00 c186f4c0 [ 64.583751] 1e20: c1906488 29e34000 c1903080 c03bdca4 00000000 eaa6f218 00000000 eb6a45c0 [ 64.591886] 1e40: eb6a45c0 20010193 00000003 c03c0a68 20010193 3f7231be c1903084 00000002 [ 64.600022] 1e60: 00000082 00000001 ffffe000 c1a9e0a4 00000100 c0302298 02b64722 0000000f [ 64.608157] 1e80: c186b3c8 c1877540 c19064ac 0000000a c186b350 ffffa401 c1903d00 c1107348 [ 64.616292] 1ea0: 00200102 c0d87a14 ea823c00 ffffe000 00000012 00000000 00000000 ea810800 [ 64.624427] 1ec0: f0803000 c1876ba8 00000000 c034c784 c18774b8 c039fb50 c1906c90 c1978aac [ 64.632562] 1ee0: f080200c f0802000 c1901f10 c0709ca8 c03091a0 60010013 ffffffff c1901f44 [ 64.640697] 1f00: 00000000 c1900000 c1876ba8 c0301a8c 00000000 000070a0 eb6ac1a0 c031da60 [ 64.648832] 1f20: ffffe000 c19064ac c19064f0 00000001 00000000 c1906488 c1876ba8 00000000 [ 64.656967] 1f40: ffffffff c1901f60 c030919c c03091a0 60010013 ffffffff 00000051 00000000 [ 64.665102] 1f60: ffffe000 c0376aa4 c1a9da37 ffffffff 00000037 3f7231be c1ab20c0 000000cc [ 64.673238] 1f80: c1906488 c1906480 ffffffff 00000037 c1ab20c0 c1ab20c0 00000001 c0376e1c [ 64.681373] 1fa0: c1ab2118 c1700ea8 ffffffff ffffffff 00000000 c1700754 c17dfa40 ebfffd80 [ 64.689509] 1fc0: 00000000 c17dfa40 3f7733be 00000000 00000000 c1700330 00000051 10c0387d [ 64.697644] 1fe0: 00000000 8f000000 410fc075 10c5387d 00000000 00000000 00000000 00000000 [ 64.705788] [<c03bd734>] (call_timer_fn) from [<c03bd95c>] (expire_timers+0xd8/0x144) [ 64.713579] [<c03bd95c>] (expire_timers) from [<c03bdca4>] (run_timer_softirq+0xe4/0x1dc) [ 64.721716] [<c03bdca4>] (run_timer_softirq) from [<c0302298>] (__do_softirq+0x130/0x3c8) [ 64.729854] [<c0302298>] (__do_softirq) from [<c034c784>] (irq_exit+0xbc/0xd8) [ 64.737040] [<c034c784>] (irq_exit) from [<c039fb50>] (__handle_domain_irq+0x60/0xb4) [ 64.744833] [<c039fb50>] (__handle_domain_irq) from [<c0709ca8>] (gic_handle_irq+0x58/0x9c) [ 64.753143] [<c0709ca8>] (gic_handle_irq) from [<c0301a8c>] (__irq_svc+0x6c/0x90) [ 64.760583] Exception stack(0xc1901f10 to 0xc1901f58) [ 64.765605] 1f00: 00000000 000070a0 eb6ac1a0 c031da60 [ 64.773740] 1f20: ffffe000 c19064ac c19064f0 00000001 00000000 c1906488 c1876ba8 00000000 [ 64.781873] 1f40: ffffffff c1901f60 c030919c c03091a0 60010013 ffffffff [ 64.788456] [<c0301a8c>] (__irq_svc) from [<c03091a0>] (arch_cpu_idle+0x38/0x3c) [ 64.795816] [<c03091a0>] (arch_cpu_idle) from [<c0376aa4>] (do_idle+0x1bc/0x298) [ 64.803175] [<c0376aa4>] (do_idle) from [<c0376e1c>] (cpu_startup_entry+0x18/0x1c) [ 64.810707] [<c0376e1c>] (cpu_startup_entry) from [<c1700ea8>] (start_kernel+0x480/0x4ac) [ 64.818839] Code: bad PC value [ 64.821890] ---[ end trace e226ed97b1c584cd ]--- [ 64.826482] Kernel panic - not syncing: Fatal exception in interrupt [ 64.832807] CPU1: stopping [ 64.835501] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G D 5.2.0-rc5-01634-ge3a2773ba9e5 #1246 [ 64.845013] Hardware name: Freescale LS1021A [ 64.849266] [<c0312394>] (unwind_backtrace) from [<c030cc74>] (show_stack+0x10/0x14) [ 64.856972] [<c030cc74>] (show_stack) from [<c0ff4138>] (dump_stack+0xb4/0xc8) [ 64.864159] [<c0ff4138>] (dump_stack) from [<c0310854>] (handle_IPI+0x3bc/0x3dc) [ 64.871519] [<c0310854>] (handle_IPI) from [<c0709ce8>] (gic_handle_irq+0x98/0x9c) [ 64.879050] [<c0709ce8>] (gic_handle_irq) from [<c0301a8c>] (__irq_svc+0x6c/0x90) [ 64.886489] Exception stack(0xea8cbf60 to 0xea8cbfa8) [ 64.891514] bf60: 00000000 0000307c eb6c11a0 c031da60 ffffe000 c19064ac c19064f0 00000002 [ 64.899649] bf80: 00000000 c1906488 c1876ba8 00000000 00000000 ea8cbfb0 c030919c c03091a0 [ 64.907780] bfa0: 600d0013 ffffffff [ 64.911250] [<c0301a8c>] (__irq_svc) from [<c03091a0>] (arch_cpu_idle+0x38/0x3c) [ 64.918609] [<c03091a0>] (arch_cpu_idle) from [<c0376aa4>] (do_idle+0x1bc/0x298) [ 64.925967] [<c0376aa4>] (do_idle) from [<c0376e1c>] (cpu_startup_entry+0x18/0x1c) [ 64.933496] [<c0376e1c>] (cpu_startup_entry) from [<803025cc>] (0x803025cc) [ 64.940422] Rebooting in 3 seconds.. In this case, what happened is that the DSA driver failed to probe at boot time due to a PHY issue during phylink_connect_phy: [ 2.245607] fsl-gianfar soc:ethernet@2d90000 eth2: error -19 setting up slave phy [ 2.258051] sja1105 spi0.1: failed to create slave for port 0.0 Fixes: bb77f36a ("net: dsa: sja1105: Add support for the PTP clock") Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Vladimir Oltean authored
As Arnd Bergmann pointed out in commit 78fe8a28 ("net: dsa: sja1105: fix ptp link error"), there is no point in having PTP support as a separate loadable kernel module. So remove the exported symbols and make sja1105.ko contain PTP support or not based on CONFIG_NET_DSA_SJA1105_PTP. Signed-off-by:
-
David S. Miller authored
Marek Vasut says: ==================== net: dsa: microchip: Convert to regmap This patchset converts KSZ9477 switch driver to regmap. This was tested with extra patches on KSZ8795. This was also tested on KSZ9477 on Microchip KSZ9477EVB board, which I now have. ==================== Signed-off-by:Marek Vasut <marex@denx.de>
-
Marek Vasut authored
Regmap provides bit manipulation functions to set/clear bits, use those insted of reimplementing them. Signed-off-by:
-
Marek Vasut authored
The regmap config tables are rather similar for various generations of the KSZ8xxx/KSZ9xxx switches. Introduce a macro which allows generating those tables without duplication. Note that $regalign parameter is not used right now, but will be used in KSZ87xx series switches. Signed-off-by:
-
Marek Vasut authored
Since the driver now uses regmap , get rid of ad-hoc ksz_io_ops abstraction, which no longer has any meaning. Moreover, since regmap has it's own locking, get rid of the register access mutex. Signed-off-by:
-
Marek Vasut authored
Add basic SPI regmap support into the driver. Previous patches unconver that ksz_spi_write() is always ever called with len = 1, 2 or 4. We can thus drop the if (len > SPI_TX_BUF_LEN) check and we can also drop the allocation of the txbuf which is part of the driver data and wastes 256 bytes for no reason. Regmap covers the whole thing now. Signed-off-by:
-
Marek Vasut authored
Factor out the code which sends out the register read/write opcodes to the switch, since the code differs in single bit between read and write. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Marek Vasut authored
The indirect function call to dev->dev_ops->get_port_addr() is expensive especially if called for every single register access, and only returns the value of PORT_CTRL_ADDR() macro. Use PORT_CTRL_ADDR() macro directly instead. Signed-off-by:
-
Marek Vasut authored
These functions are only used by the KSZ9477 code, move them from the header into that code. Note that these functions will be soon replaced by regmap equivalents. Signed-off-by:
-
Marek Vasut authored
The functions in the header file are static, and the header file is included from single C file, just inline the code into the C file. The bonus is that it's easier to spot further content to clean up. Signed-off-by:
-
Marek Vasut authored
These functions and callbacks are never used, remove them. Signed-off-by:
-
Marek Vasut authored
These functions and callbacks are never used, remove them. Signed-off-by:
-
David S. Miller authored
Igor Russkikh says: ==================== net: aquantia: implement vlan offloads This patchset introduces hardware VLAN offload support and also does some maintenance: we replace driver version with uts version string, add documentation file for atlantic driver, and update maintainers adding Igor as a maintainer. v3: shuffle doc sections, per Andrew's comments v2: updates in doc, gpl spdx tag cleanup ==================== Signed-off-by: -
Igor Russkikh authored
set_features should update flags and reinit hardware if vlan offload settings were changed. Signed-off-by:
Igor Russkikh <igor.russkikh@aquantia.com> Tested-by:
Nikita Danilov <ndanilov@aquantia.com> Signed-off-by:
-
Igor Russkikh authored
Update datapath by adding logic related to hardware assisted vlan strip/insert behaviour. Tested-by:
-
Igor Russkikh authored
Updating features and vlan_features with vlan HW offload. Added vlan_tag fields to rx/tx ring_buff to track vlan related data. Tested-by:
-
Igor Russkikh authored
Register declaration macros required to work with vlan offload mode. Tested-by:
-
Igor Russkikh authored
It was noticed some files had -or-later, however overall driver has -only license. Clean this up. Signed-off-by:
-
Igor Russkikh authored
Aquantia is resposible now for all new features and bugfixes. Reflect that in MAINTAINERS. Signed-off-by:
-
Igor Russkikh authored
Document contains configuration options description, details and examples of driver various settings. Signed-off-by:
-
Igor Russkikh authored
As it was discussed some time previously, driver is better to report kernel version string, as it in a best way identifies the codebase. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2019-06-26 This series contains updates to ixgbe and i40e only. Mauro S. M. Rodrigues update the ixgbe driver to handle transceivers who comply with SFF-8472 but do not implement the Digital Diagnostic Monitoring (DOM) interface. Update the driver to check the necessary bits to see if DOM is implemented before trying to read the additional 256 bytes in the EEPROM for DOM data. Young Xiao fixes a potential divide by zero issue in ixgbe driver. Aleksandr fixes i40e to recognize 2.5 and 5.0 GbE link speeds so that it is not reported as "Unknown bps". Fixes the driver to read the firmware LLDP agent status during DCB initialization, and to properly log the LLDP agent status to help with debugging when DCB fails to initialize. Martyna fixes i40e for the missing supported and advertised link modes information in ethtool. Jake fixes a function header comment that was incorrect for a PTP function in i40e. Maciej fixes an issue for i40e when a XDP program is loaded the descriptor count gets reset to the default value, resolve the issue by making the current descriptor count persistent across resets. Alice corrects a copyright date which she found to be incorrect. Piotr adds a log entry when the traffic class 0 is added or deleted, which was not being logged previously. Gustavo A. R. Silva updates i40e to use struct_size() where possible. ==================== Signed-off-by: -
David S. Miller authored
Julian Wiedmann says: ==================== s390/qeth: updates 2019-06-27 please apply another round of qeth updates for net-next. This completes the conversion of the control path to use dynamically allocated cmd buffers, along with some fine-tuning for the route validation fix that recently went into -net. ==================== Signed-off-by: -
Julian Wiedmann authored
The cast type currently gets selected in .ndo_start_xmit, and is then piped through several layers until it's stored into the HW header. Push the selection down into qeth_l?_fill_header() to (1) reduce the number of xmit-wide parameters, and (2) merge the two route validation checks into just one. Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
-
Julian Wiedmann authored
As follow-up to commit 0cd6783d ("s390/qeth: check dst entry before use"), consolidate the dst_check() logic into a single helper and add a wrapper around the cast type selection. Signed-off-by:
-
Julian Wiedmann authored
Use napi_gro_receive() to pass up all types of packets that a L3 device may receive. 1) For proper L2 packets received by the IQD sniffer, this is the obvious thing to do. 2) For af_iucv (which doesn't provide a GRO assist), the GRO code will transparently fall back to netif_receive_skb(). So there's no need to special-case this traffic in our code. Signed-off-by:
-
Julian Wiedmann authored
De-duplicate the pm callback implementations from the two sub-drivers, replacing them with core helpers that delegate to the .set_online and .set_offline callbacks. Signed-off-by:
-
Julian Wiedmann authored
Apply some cleanups to qeth_snmp_command() and its callback: 1. when accessing the user data, use the proper struct instead of hard-coded offsets. Also copy the request data straight into the allocated cmd, skipping the extra memdup_user() to a tmp buffer. 2. capping the request length is no longer needed, the same check gets applied at a base level in qeth_alloc_cmd(). 3. clean up some duplicated (and misindented) trace statements. Signed-off-by:
-
Julian Wiedmann authored
Now that all cmds are dynamically allocated, the code for static cmd buffers can go away entirely. Resulting in a nice reduction of code/data size & complexity, while removing the risk that qeth_clear_cmd_buffers() releases cmds that are still in-flight. Signed-off-by:
-
Julian Wiedmann authored
The base MPC cmds are the last remaining user of the static cmd buffers. Port them over to use dynamic allocation, and stop backing the write channel's cmd buffers with pages. Signed-off-by:
-
Julian Wiedmann authored
The VNICC code is somewhat quirky in that it defers the whole cmd setup to a common helper qeth_l2_vnicc_request(). Some of the cmd specifics are then passed in via parameter, while others are simply hard-coded. Split the whole machinery up into the usual format: one helper that allocates the cmd & fills in the common fields, while all the cmd originators take care of their sub-cmd type specific work. This makes it much easier to calculate the cmd's precise length, and reduces code complexity. Signed-off-by:
Alexandra Winter <wintera@linux.ibm.com> Signed-off-by:
-
Julian Wiedmann authored
Add a new wrapper that allocates DIAG cmds of the right size, and fills in the common fields. Signed-off-by:
-
