As Jungyeon reported in bugzilla:

https://bugzilla.kernel.org/show_bug.cgi?id=203221

- Overview
When mounting the attached crafted image and running program, this error is reported.

The image is intentionally fuzzed from a normal f2fs image for testing and I enabled option CONFIG_F2FS_CHECK_FS on.

- Reproduces
cc poc_07.c
mkdir test
mount -t f2fs tmp.img test
cp a.out test
cd test
sudo ./a.out

- Messages
 kernel BUG at fs/f2fs/node.c:1279!
 RIP: 0010:read_node_page+0xcf/0xf0
 Call Trace:
  __get_node_page+0x6b/0x2f0
  f2fs_iget+0x8f/0xdf0
  f2fs_lookup+0x136/0x320
  __lookup_slow+0x92/0x140
  lookup_slow+0x30/0x50
  walk_component+0x1c1/0x350
  path_lookupat+0x62/0x200
  filename_lookup+0xb3/0x1a0
  do_fchmodat+0x3e/0xa0
  __x64_sys_chmod+0x12/0x20
  do_syscall_64+0x43/0xf0
  entry_SYSCALL_64_after_hwframe+0x44/0xa9

On below paths, we can have opportunity to readahead inode page
- gc_node_segment -> f2fs_ra_node_page
- gc_data_segment -> f2fs_ra_node_page
- f2fs_fill_dentries -> f2fs_ra_node_page

Unlike synchronized read, on readahead path, we can set page uptodate
before verifying page's checksum, then read_node_page() will trigger
kernel panic once it encounters a uptodated page w/ incorrect checksum.

So considering readahead scenario, we have to do checksum each time
when loading inode page even if it is uptodated.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

As Jungyeon reported in bugzilla:

https://bugzilla.kernel.org/show_bug.cgi?id=203219

- Overview
When mounting the attached crafted image and running program, I got this error.
Additionally, it hangs on sync after running the program.

The image is intentionally fuzzed from a normal f2fs image for testing and I enabled option CONFIG_F2FS_CHECK_FS on.

- Reproduces
cc poc_06.c
mkdir test
mount -t f2fs tmp.img test
cp a.out test
cd test
sudo ./a.out
sync

- Messages
 kernel BUG at fs/f2fs/node.c:1183!
 RIP: 0010:f2fs_remove_inode_page+0x294/0x2d0
 Call Trace:
  f2fs_evict_inode+0x2a3/0x3a0
  evict+0xba/0x180
  __dentry_kill+0xbe/0x160
  dentry_kill+0x46/0x180
  dput+0xbb/0x100
  do_renameat2+0x3c9/0x550
  __x64_sys_rename+0x17/0x20
  do_syscall_64+0x43/0xf0
  entry_SYSCALL_64_after_hwframe+0x44/0xa9

The reason is f2fs_remove_inode_page() will trigger kernel panic due to
inconsistent i_blocks value of inode.

To avoid panic, let's just print debug message and set SBI_NEED_FSCK to
give a hint to fsck for latter repairing of potential image corruption.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
[Jaegeuk Kim: fix build warning and add unlikely]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

As Jungyeon reported in bugzilla:

https://bugzilla.kernel.org/show_bug.cgi?id=203217

- Overview
When mounting the attached crafted image and running program, I got this error.
Additionally, it hangs on sync after running the program.

The image is intentionally fuzzed from a normal f2fs image for testing and I enabled option CONFIG_F2FS_CHECK_FS on.

- Reproduces
cc poc_test_05.c
mkdir test
mount -t f2fs tmp.img test
sudo ./a.out
sync

- Messages
 kernel BUG at fs/f2fs/inode.c:707!
 RIP: 0010:f2fs_evict_inode+0x33f/0x3a0
 Call Trace:
  evict+0xba/0x180
  f2fs_iget+0x598/0xdf0
  f2fs_lookup+0x136/0x320
  __lookup_slow+0x92/0x140
  lookup_slow+0x30/0x50
  walk_component+0x1c1/0x350
  path_lookupat+0x62/0x200
  filename_lookup+0xb3/0x1a0
  do_readlinkat+0x56/0x110
  __x64_sys_readlink+0x16/0x20
  do_syscall_64+0x43/0xf0
  entry_SYSCALL_64_after_hwframe+0x44/0xa9

During inode loading, __recover_inline_status() can recovery inode status
and set inode dirty, once we failed in following process, it will fail
the check in f2fs_evict_inode, result in trigger BUG_ON().

Let's clear dirty inode in error path of f2fs_iget() to avoid panic.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

Just removing '\n' in f2fs_msg(, "\n") to avoid redundant new blank line.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

This patch changes codes as below:
- don't use is_read_io() as a condition to judge the meta IO.
- use .is_por to replace .is_meta to indicate IO is from recovery explicitly.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

As Jungyeon reported in bugzilla:

https://bugzilla.kernel.org/show_bug.cgi?id=203213

- Overview
When mounting the attached crafted image and running program, I got this error.
Additionally, it hangs on sync after running the this script.

The image is intentionally fuzzed from a normal f2fs image for testing and I enabled option CONFIG_F2FS_CHECK_FS on.

- Reproduces
mkdir test
mount -t f2fs tmp.img test
cp a.out test
cd test
sudo ./a.out
sync

 kernel BUG at fs/f2fs/f2fs.h:2012!
 RIP: 0010:truncate_node+0x2c9/0x2e0
 Call Trace:
  f2fs_truncate_xattr_node+0xa1/0x130
  f2fs_remove_inode_page+0x82/0x2d0
  f2fs_evict_inode+0x2a3/0x3a0
  evict+0xba/0x180
  __dentry_kill+0xbe/0x160
  dentry_kill+0x46/0x180
  dput+0xbb/0x100
  do_renameat2+0x3c9/0x550
  __x64_sys_rename+0x17/0x20
  do_syscall_64+0x43/0xf0
  entry_SYSCALL_64_after_hwframe+0x44/0xa9

The reason is dec_valid_node_count() will trigger kernel panic due to
inconsistent count in between inode.i_blocks and actual block.

To avoid panic, let's just print debug message and set SBI_NEED_FSCK to
give a hint to fsck for latter repairing.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
[Jaegeuk Kim: fix build warning and add unlikely]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

As Jungyeon reported in bugzilla:

https://bugzilla.kernel.org/show_bug.cgi?id=203209

- Overview
When mounting the attached crafted image and running program, I got this error.
Additionally, it hangs on sync after the this script.

The image is intentionally fuzzed from a normal f2fs image for testing and I enabled option CONFIG_F2FS_CHECK_FS on.

- Reproduces
cc poc_01.c
./run.sh f2fs
sync

 kernel BUG at fs/f2fs/f2fs.h:1788!
 RIP: 0010:f2fs_truncate_data_blocks_range+0x342/0x350
 Call Trace:
  f2fs_truncate_blocks+0x36d/0x3c0
  f2fs_truncate+0x88/0x110
  f2fs_setattr+0x3e1/0x460
  notify_change+0x2da/0x400
  do_truncate+0x6d/0xb0
  do_sys_ftruncate+0xf1/0x160
  do_syscall_64+0x43/0xf0
  entry_SYSCALL_64_after_hwframe+0x44/0xa9

The reason is dec_valid_block_count() will trigger kernel panic due to
inconsistent count in between inode.i_blocks and actual block.

To avoid panic, let's just print debug message and set SBI_NEED_FSCK to
give a hint to fsck for latter repairing.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
[Jaegeuk Kim: fix build warning and add unlikely]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

With below mkfs and mount option:

MKFS_OPTIONS  -- -O extra_attr -O project_quota -O inode_checksum -O flexible_inline_xattr -O inode_crtime -f
MOUNT_OPTIONS -- -o noinline_xattr

We may miss xattr data with below testcase:
- mkdir dir
- setfattr -n "user.name" -v 0 dir
- for ((i = 0; i < 190; i++)) do touch dir/$i; done
- umount
- mount
- getfattr -n "user.name" dir

user.name: No such attribute

The root cause is that we persist xattr data into reserved inline xattr
space, even if inline_xattr is not enable in inline directory inode, after
inline dentry conversion, reserved space no longer exists, so that xattr
data missed.

Let's use inline xattr space only if inline_xattr flag is set on inode
to fix this iusse.

Fixes: 6afc662e ("f2fs: support flexible inline xattr size")
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

With below mkfs and mount option, generic/339 of fstest will report that
scratch image becomes corrupted.

MKFS_OPTIONS  -- -O extra_attr -O project_quota -O inode_checksum -O flexible_inline_xattr -O inode_crtime -f /dev/zram1
MOUNT_OPTIONS -- -o acl,user_xattr -o discard,noinline_xattr /dev/zram1 /mnt/scratch_f2fs

[ASSERT] (f2fs_check_dirent_position:1315)  --> Wrong position of dirent pino:1970, name: (...)
level:8, dir_level:0, pgofs:951, correct range:[900, 901]

In old kernel, inline data and directory always reserved 200 bytes in
inode layout, even if inline_xattr is disabled, then new kernel tries
to retrieve that space for non-inline xattr inode, but for inline dentry,
its layout size should be fixed, so we just keep that reserved space.

But the problem here is that, after inline dentry conversion, inline
dentry layout no longer exists, if we still reserve inline xattr space,
after dents updates, there will be a hole in inline xattr space, which
can break hierarchy hash directory structure.

This patch fixes this issue by retrieving inline xattr space after
inline dentry conversion.

Fixes: 6afc662e ("f2fs: support flexible inline xattr size")
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

There are some places in where we missed to unlock page or unlock page
incorrectly, fix them.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

As Jungyeon reported in bugzilla:

https://bugzilla.kernel.org/show_bug.cgi?id=203211

- Overview
When mounting the attached crafted image and making a new file, I got this error and the error messages keep repeating.

The image is intentionally fuzzed from a normal f2fs image for testing and I run with option CONFIG_F2FS_CHECK_FS on.

- Reproduces
mkdir test
mount -t f2fs tmp.img test
cd test
touch t

- Messages
[   58.820451] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.821485] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.822530] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.823571] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.824616] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.825640] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.826663] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.827698] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.828719] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.829759] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.830783] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.831828] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.832869] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.833888] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.834945] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.835996] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.837028] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.838051] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.839072] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.840100] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.841147] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.842186] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.843214] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.844267] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.845282] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.846305] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
[   58.847341] F2FS-fs (sdb): Inconsistent segment (1) type [1, 0] in SSA and SIT
... (repeating)

During GC, if segment type stored in SSA and SIT is inconsistent, we just
skip migrating current segment directly, since we need to know the exact
type to decide the migration function we use.

So in foreground GC, we will easily run into a infinite loop as we may
select the same victim segment which has inconsistent type due to greedy
policy. In order to end up this, we choose to shutdown filesystem. For
backgrond GC, we need to do that as well, so that we can avoid latter
potential infinite looped foreground GC.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

changed passing function argument "0 to NULL" to fix below sparse
warning

fs/f2fs/data.c:426:47: warning: Using plain integer as NULL pointer
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

This patch adds tracepoint for f2fs_file_write_iter().
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

Commit af033b2a ("f2fs: guarantee journalled quota data by checkpoint")
added function is_journalled_quota() in f2fs.h, but it located outside of
_LINUX_F2FS_H macro coverage, it has been fixed with commit 0af725fc
("f2fs: fix wrong #endif").

But anyway, in order to avoid making same mistake latter, let's add single
line comment to notice which #if the last #endif is corresponding to.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
[Jaegeuk Kim: Remove unnecessary empty EOL]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

As Hagbard Celine reported:

Hi, this is a long standing bug that I've hit before on older kernels,
but I was not able to get the syslog saved because of the nature of
the bug. This time I had booted form a pen-drive, and was able to save
the log to it's efi-partition.
What i did to trigger it was to create a partition and format it f2fs,
then mount it with options:
"rw,relatime,lazytime,background_gc=on,disable_ext_identify,discard,heap,user_xattr,inline_xattr,acl,inline_data,inline_dentry,flush_merge,data_flush,extent_cache,mode=adaptive,active_logs=6,whint_mode=fs-based,alloc_mode=default,fsync_mode=strict".
Then I unpacked a big .tar.xz to the partition (I used a
gentoo-stage3-tarball as I was in process of installing Gentoo).

Same options just without data_flush gives no problems.

Mar 20 20:54:01 usbgentoo kernel: FAT-fs (nvme0n1p4): Volume was not
properly unmounted. Some data may be corrupt. Please run fsck.
Mar 20 21:05:23 usbgentoo kernel: kworker/dying (1588) used greatest
stack depth: 12064 bytes left
Mar 20 21:06:40 usbgentoo kernel: BUG: stack guard page was hit at
00000000a4b0733c (stack is 0000000056016422..0000000096e7463f)
Mar 20 21:06:40 usbgentoo kernel: kernel stack overflow

......

Mar 20 21:06:40 usbgentoo kernel: Call Trace:
Mar 20 21:06:40 usbgentoo kernel:  read_node_page+0x71/0xf0
Mar 20 21:06:40 usbgentoo kernel:  ? xas_load+0x8/0x50
Mar 20 21:06:40 usbgentoo kernel:  __get_node_page+0x73/0x2a0
Mar 20 21:06:40 usbgentoo kernel:  f2fs_get_dnode_of_data+0x34e/0x580
Mar 20 21:06:40 usbgentoo kernel:  f2fs_write_inline_data+0x5e/0x2a0
Mar 20 21:06:40 usbgentoo kernel:  __write_data_page+0x421/0x690
Mar 20 21:06:40 usbgentoo kernel:  f2fs_write_cache_pages+0x1cf/0x460
Mar 20 21:06:40 usbgentoo kernel:  f2fs_write_data_pages+0x2b3/0x2e0
Mar 20 21:06:40 usbgentoo kernel:  ? f2fs_inode_chksum_verify+0x1d/0xc0
Mar 20 21:06:40 usbgentoo kernel:  ? read_node_page+0x71/0xf0
Mar 20 21:06:40 usbgentoo kernel:  do_writepages+0x3c/0xd0
Mar 20 21:06:40 usbgentoo kernel:  __filemap_fdatawrite_range+0x7c/0xb0
Mar 20 21:06:40 usbgentoo kernel:  f2fs_sync_dirty_inodes+0xf2/0x200
Mar 20 21:06:40 usbgentoo kernel:  f2fs_balance_fs_bg+0x2a3/0x2c0
Mar 20 21:06:40 usbgentoo kernel:  ? f2fs_inode_dirtied+0x21/0xc0
Mar 20 21:06:40 usbgentoo kernel:  f2fs_balance_fs+0xd6/0x2b0
Mar 20 21:06:40 usbgentoo kernel:  __write_data_page+0x4fb/0x690

......

Mar 20 21:06:40 usbgentoo kernel:  __writeback_single_inode+0x2a1/0x340
Mar 20 21:06:40 usbgentoo kernel:  ? soft_cursor+0x1b4/0x220
Mar 20 21:06:40 usbgentoo kernel:  writeback_sb_inodes+0x1d5/0x3e0
Mar 20 21:06:40 usbgentoo kernel:  __writeback_inodes_wb+0x58/0xa0
Mar 20 21:06:40 usbgentoo kernel:  wb_writeback+0x250/0x2e0
Mar 20 21:06:40 usbgentoo kernel:  ? 0xffffffff8c000000
Mar 20 21:06:40 usbgentoo kernel:  ? cpumask_next+0x16/0x20
Mar 20 21:06:40 usbgentoo kernel:  wb_workfn+0x2f6/0x3b0
Mar 20 21:06:40 usbgentoo kernel:  ? __switch_to_asm+0x40/0x70
Mar 20 21:06:40 usbgentoo kernel:  process_one_work+0x1f5/0x3f0
Mar 20 21:06:40 usbgentoo kernel:  worker_thread+0x28/0x3c0
Mar 20 21:06:40 usbgentoo kernel:  ? rescuer_thread+0x330/0x330
Mar 20 21:06:40 usbgentoo kernel:  kthread+0x10e/0x130
Mar 20 21:06:40 usbgentoo kernel:  ? kthread_create_on_node+0x60/0x60
Mar 20 21:06:40 usbgentoo kernel:  ret_from_fork+0x35/0x40

The root cause is that we run into an infinite recursive calling in
between f2fs_balance_fs_bg and writepage() as described below:

- f2fs_write_data_pages		--- A
 - __write_data_page
  - f2fs_balance_fs
   - f2fs_balance_fs_bg		--- B
    - f2fs_sync_dirty_inodes
     - filemap_fdatawrite
      - f2fs_write_data_pages	--- A
...
          - f2fs_balance_fs_bg	--- B
...

In order to fix this issue, let's detect such condition in __write_data_page()
and just skip calling f2fs_balance_fs() recursively.
Reported-by: Hagbard Celine <hagbardcelin@gmail.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

f2fs_hw_support_discard() only tests if the super block device supports
discard. However, for a multi-device volume, not all disks used may
support discard. Improve the check performed to test all devices of
the volume and report discard as supported if at least one device of
the volume supports discard. To implement this, introduce the helper
function f2fs_bdev_support_discard(), which returns true for zoned block
devices (where discard is processed as a zone reset) and for regular
disks supporting the discard command.

f2fs_bdev_support_discard() is also used in __queue_discard_cmd() to
handle discard command issuing for a particular device of the volume.
That is, prevent issuing a discard command for block devices that do
not support it.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

For zoned block devices, an array of zone types for each device is
allocated and initialized in order to determine if a section is stored
on a sequential zone (zone reset needed) or a conventional zone (no
zone reset needed and regular discard applies). Considering this usage,
the zone types stored in memory can be replaced with a bitmap to
indicate an equivalent information, that is, if a zone is sequential or
not. This reduces the memory usage for each zoned device by roughly 8:
on a 14TB disk with zones of 256 MB, the zone type array consumes
13x4KB pages while the bitmap uses only 2x4KB pages.

This patch changes the f2fs_dev_info structure blkz_type field to the
bitmap blkz_seq. Access to this bitmap is done using the helper
function f2fs_blkz_is_seq(), which is a rewrite of the function
get_blkz_type().
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

For a single device mount using a zoned block device, the zone
information for the device is stored in the sbi->devs single entry
array and sbi->s_ndevs is set to 1. This differs from a single device
mount using a regular block device which does not allocate sbi->devs
and sets sbi->s_ndevs to 0.

However, sbi->s_devs == 0 condition is used throughout the code to
differentiate a single device mount from a multi-device mount where
sbi->s_ndevs is always larger than 1. This results in problems with
single zoned block device volumes as these are treated as multi-device
mounts but do not have the start_blk and end_blk information set. One
of the problem observed is skipping of zone discard issuing resulting in
write commands being issued to full zones or unaligned to a zone write
pointer.

Fix this problem by simply treating the cases sbi->s_ndevs == 0 (single
regular block device mount) and sbi->s_ndevs == 1 (single zoned block
device mount) in the same manner. This is done by introducing the
helper function f2fs_is_multi_device() and using this helper in place
of direct tests of sbi->s_ndevs value, improving code readability.

Fixes: 7bb3a371 ("f2fs: Fix zoned block device support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

Pull HID fixes from Jiri Kosina:

 - build dependency fix for hid-asus from Arnd Bergmann

 - addition of omitted mapping of _ASSISTANT key from Dmitry Torokhov

 - race condition fix in hid-debug inftastructure from He, Bo

 - fixed support for devices with big maximum report size from Kai-Heng
   Feng

 - deadlock fix in hid-steam from Rodrigo Rivas Costa

 - quite a few device-specific quirks

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
  HID: input: add mapping for Assistant key
  HID: i2c-hid: Disable runtime PM on Synaptics touchpad
  HID: quirks: Fix keyboard + touchpad on Lenovo Miix 630
  HID: logitech: Handle 0 scroll events for the m560
  HID: debug: fix race condition with between rdesc_show() and device removal
  HID: logitech: check the return value of create_singlethread_workqueue
  HID: Increase maximum report size allowed by hid_field_extract()
  HID: steam: fix deadlock with input devices.
  HID: uclogic: remove redudant duplicated null check on ver_ptr
  HID: quirks: Drop misused kernel-doc annotation
  HID: hid-asus: select CONFIG_POWER_SUPPLY
  HID: quirks: use correct format chars in dbg_hid

According to HUTRR89 usage 0x1cb from the consumer page was assigned to
allow launching desktop-aware assistant application, so let's add the
mapping.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Pull pidfd fix from Christian Brauner:
 "This should be an uncontroversial fix for pidfd_send_signal() by Jann
  to better align it's behavior with other signal sending functions:

  In one of the early versions of the patchset it was suggested to not
  unconditionally error out when a signal with SI_USER is sent to a
  non-current task (cf. [1]).

  Instead, pidfd_send_signal() currently silently changes this to a
  regular kill signal. While this is technically fine, the semantics are
  weird since the kernel just silently converts a user's request behind
  their back and also no other signal sending function allows to do
  this. It gets more hairy when we introduce sending signals to a
  specific thread soon.

  So let's align pidfd_send_signal() with all the other signal sending
  functions and error out when SI_USER signals are sent to a non-current
  task"

* tag 'pidfd-fixes-v5.1-rc3' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux:
  signal: don't silently convert SI_USER signals to non-current pidfd

Merge tag 'hwmon-for-v5.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "Couple of minor hwmon fixes"

* tag 'hwmon-for-v5.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  dt-bindings: hwmon: (adc128d818) Specify ti,mode property size
  hwmon: (ntc_thermistor) Fix temperature type reporting
  hwmon: (occ) Fix power sensor indexing
  hwmon: (w83773g) Select REGMAP_I2C to fix build error

The @linaro version won't be valid much longer.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The current sys_pidfd_send_signal() silently turns signals with explicit
SI_USER context that are sent to non-current tasks into signals with
kernel-generated siginfo.
This is unlike do_rt_sigqueueinfo(), which returns -EPERM in this case.
If a user actually wants to send a signal with kernel-provided siginfo,
they can do that with pidfd_send_signal(pidfd, sig, NULL, 0); so allowing
this case is unnecessary.

Instead of silently replacing the siginfo, just bail out with an error;
this is consistent with other interfaces and avoids special-casing behavior
based on security checks.

Fixes: 3eb39f47 ("signal: add pidfd_send_signal() syscall")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Christian Brauner <christian@brauner.io>

Pull aio race fixes and cleanups from Al Viro.

The aio code had more issues with error handling and races with the aio
completing at just the right (wrong) time along with freeing the file
descriptor when another thread closes the file.

Just a couple of these commits are the actual fixes: the others are
cleanups to either make the fixes simpler, or to make the code legible
and understandable enough that we hope there's no more fundamental races
hiding.

* 'work.aio' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  aio: move sanity checks and request allocation to io_submit_one()
  deal with get_reqs_available() in aio_get_req() itself
  aio: move dropping ->ki_eventfd into iocb_destroy()
  make aio_read()/aio_write() return int
  Fix aio_poll() races
  aio: store event at final iocb_put()
  aio: keep io_event in aio_kiocb
  aio: fold lookup_kiocb() into its sole caller
  pin iocb through aio.

Pull symlink fixes from Al Viro:
 "The ceph fix is already in mainline, Daniel's bpf fix is in bpf tree
  (1da6c4d9 "bpf: fix use after free in bpf_evict_inode"), the rest
  is in here"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  debugfs: fix use-after-free on symlink traversal
  ubifs: fix use-after-free on symlink traversal
  jffs2: fix use-after-free on symlink traversal

We have a new Dell laptop which has the synaptics I2C touchpad
(06cb:7e7e) on it. After booting up the Linux, the touchpad doesn't
work, there is no interrupt when touching the touchpad, after
disable the runtime PM, everything works well.

I also tried the quirk of I2C_HID_QUIRK_DELAY_AFTER_SLEEP, it is
better after applied this quirk, there are interrupts but data it
reports is invalid.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

symlink body shouldn't be freed without an RCU delay.  Switch debugfs to
->destroy_inode() and use of call_rcu(); free both the inode and symlink
body in the callback.  Similar to solution for bpf, only here it's even
more obvious that ->evict_inode() can be dropped.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

free the symlink body after the same RCU delay we have for freeing the
struct inode itself, so that traversal during RCU pathwalk wouldn't step
into freed memory.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

free the symlink body after the same RCU delay we have for freeing the
struct inode itself, so that traversal during RCU pathwalk wouldn't step
into freed memory.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull KVM fixes from Paolo Bonzini:
 "A collection of x86 and ARM bugfixes, and some improvements to
  documentation.

  On top of this, a cleanup of kvm_para.h headers, which were exported
  by some architectures even though they not support KVM at all. This is
  responsible for all the Kbuild changes in the diffstat"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
  Documentation: kvm: clarify KVM_SET_USER_MEMORY_REGION
  KVM: doc: Document the life cycle of a VM and its resources
  KVM: selftests: complete IO before migrating guest state
  KVM: selftests: disable stack protector for all KVM tests
  KVM: selftests: explicitly disable PIE for tests
  KVM: selftests: assert on exit reason in CR4/cpuid sync test
  KVM: x86: update %rip after emulating IO
  x86/kvm/hyper-v: avoid spurious pending stimer on vCPU init
  kvm/x86: Move MSR_IA32_ARCH_CAPABILITIES to array emulated_msrs
  KVM: x86: Emulate MSR_IA32_ARCH_CAPABILITIES on AMD hosts
  kvm: don't redefine flags as something else
  kvm: mmu: Used range based flushing in slot_handle_level_range
  KVM: export <linux/kvm_para.h> and <asm/kvm_para.h> iif KVM is supported
  KVM: x86: remove check on nr_mmu_pages in kvm_arch_commit_memory_region()
  kvm: nVMX: Add a vmentry check for HOST_SYSENTER_ESP and HOST_SYSENTER_EIP fields
  KVM: SVM: Workaround errata#1096 (insn_len maybe zero on SMAP violation)
  KVM: Reject device ioctls from processes other than the VM's creator
  KVM: doc: Fix incorrect word ordering regarding supported use of APIs
  KVM: x86: fix handling of role.cr4_pae and rename it to 'gpte_size'
  KVM: nVMX: Do not inherit quadrant and invalid for the root shadow EPT
  ...

Pull x86 fixes from Thomas Gleixner:
 "A pile of x86 updates:

   - Prevent exceeding he valid physical address space in the /dev/mem
     limit checks.

   - Move all header content inside the header guard to prevent compile
     failures.

   - Fix the bogus __percpu annotation in this_cpu_has() which makes
     sparse very noisy.

   - Disable switch jump tables completely when retpolines are enabled.

   - Prevent leaking the trampoline address"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/realmode: Make set_real_mode_mem() static inline
  x86/cpufeature: Fix __percpu annotation in this_cpu_has()
  x86/mm: Don't exceed the valid physical address space
  x86/retpolines: Disable switch jump tables when retpolines are enabled
  x86/realmode: Don't leak the trampoline kernel address
  x86/boot: Fix incorrect ifdeffery scope
  x86/resctrl: Remove unused variable

Pull perf tooling fixes from Thomas Gleixner:
 "Core libraries:
   - Fix max perf_event_attr.precise_ip detection.
   - Fix parser error for uncore event alias
   - Fixup ordering of kernel maps after obtaining the main kernel map
     address.

  Intel PT:
   - Fix TSC slip where A TSC packet can slip past MTC packets so that
     the timestamp appears to go backwards.
   - Fixes for exported-sql-viewer GUI conversion to python3.

  ARM coresight:
   - Fix the build by adding a missing case value for enumeration value
     introduced in newer library, that now is the required one.

  tool headers:
   - Syncronize kernel headers with the kernel, getting new io_uring and
     pidfd_send_signal syscalls so that 'perf trace' can handle them"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf pmu: Fix parser error for uncore event alias
  perf scripts python: exported-sql-viewer.py: Fix python3 support
  perf scripts python: exported-sql-viewer.py: Fix never-ending loop
  perf machine: Update kernel map address and re-order properly
  tools headers uapi: Sync powerpc's asm/kvm.h copy with the kernel sources
  tools headers: Update x86's syscall_64.tbl and uapi/asm-generic/unistd
  tools headers uapi: Update drm/i915_drm.h
  tools arch x86: Sync asm/cpufeatures.h with the kernel sources
  tools headers uapi: Sync linux/fcntl.h to get the F_SEAL_FUTURE_WRITE addition
  tools headers uapi: Sync asm-generic/mman-common.h and linux/mman.h
  perf evsel: Fix max perf_event_attr.precise_ip detection
  perf intel-pt: Fix TSC slip
  perf cs-etm: Add missing case value

Pull CPU hotplug fixes from Thomas Gleixner:
 "Two SMT/hotplug related fixes:

   - Prevent crash when HOTPLUG_CPU is disabled and the CPU bringup
     aborts. This is triggered with the 'nosmt' command line option, but
     can happen by any abort condition. As the real unplug code is not
     compiled in, prevent the fail by keeping the CPU in zombie state.

   - Enforce HOTPLUG_CPU for SMP on x86 to avoid the above situation
     completely. With 'nosmt' being a popular option it's required to
     unplug the half brought up sibling CPUs (due to the MCE wreckage)
     completely"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/smp: Enforce CONFIG_HOTPLUG_CPU when SMP=y
  cpu/hotplug: Prevent crash when CPU bringup fails on CONFIG_HOTPLUG_CPU=n

Pull locking fixlet from Thomas Gleixner:
 "Trivial update to the maintainers file"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  MAINTAINERS: Remove deleted file from futex file pattern

Pull core fixes from Thomas Gleixner:
 "A small set of core updates:

   - Make the watchdog respect the selected CPU mask again. That was
     broken by the rework of the watchdog thread management and caused
     inconsistent state and NMI watchdog being unstoppable.

   - Ensure that the objtool build can find the libelf location.

   - Remove dead kcore stub code"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  watchdog: Respect watchdog cpumask on CPU hotplug
  objtool: Query pkg-config for libelf location
  proc/kcore: Remove unused kclist_add_remap()

Pull powerpc fixes from Michael Ellerman:
 "Three non-regression fixes.

   - Our optimised memcmp could read past the end of one of the buffers
     and potentially trigger a page fault leading to an oops.

   - Some of our code to read energy management data on PowerVM had an
     endian bug leading to bogus results.

   - When reporting a machine check exception we incorrectly reported
     TLB multihits as D-Cache multhits due to a missing entry in the
     array of causes.

  Thanks to: Chandan Rajendra, Gautham R. Shenoy, Mahesh Salgaonkar,
  Segher Boessenkool, Vaidyanathan Srinivasan"

* tag 'powerpc-5.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/pseries/mce: Fix misleading print for TLB mutlihit
  powerpc/pseries/energy: Use OF accessor functions to read ibm,drc-indexes
  powerpc/64: Fix memcmp reading past the end of src/dest

Pull dmaengine fixes from Vinod Koul:

 - Revert "dmaengine: stm32-mdma: Add a check on read_u32_array" as that
   caused regression

 - Fix MAINTAINER file uniphier-mdmac.c file path

* tag 'dmaengine-fix-5.1-rc3' of git://git.infradead.org/users/vkoul/slave-dma:
  MAINTAINERS: Fix uniphier-mdmac.c file path
  dmaengine: stm32-mdma: Revert "dmaengine: stm32-mdma: Add a check on read_u32_array"

Merge tag 'led-fixes-for-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED fixes from Jacek Anaszewski:

 - fix refcnt leak on interface rename

 - use memcpy in device_name_store() to avoid including garbage from a
   previous, longer value in the device_name

 - fix a potential NULL pointer dereference in case of_match_device()
   cannot find a match

* tag 'led-fixes-for-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  leds: trigger: netdev: use memcpy in device_name_store
  leds: pca9532: fix a potential NULL pointer dereference
  leds: trigger: netdev: fix refcnt leak on interface rename