- 21 Dec, 2020 4 commits
-
-
Stephen Boyd authored
- Add some trace points for clk_set_rate() "range" functions - DVFS support for AT91 clk driver * clk-ti: clk: ti: omap5: Fix reboot DPLL lock failure when using ABE TIMERs clk: ti: Fix memleak in ti_fapll_synth_setup * clk-analog: clk: axi-clkgen: move the OF table at the bottom of the file clk: axi-clkgen: wrap limits in a struct and keep copy on the state object dt-bindings: clock: adi,axi-clkgen: convert old binding to yaml format * clk-trace: clk: Trace clk_set_rate() "range" functions * clk-at91: clk: at91: sam9x60: remove atmel,osc-bypass support clk: at91: sama7g5: register cpu clock clk: at91: clk-master: re-factor master clock clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz clk: at91: sama7g5: decrease lower limit for MCK0 rate clk: at91: sama7g5: remove mck0 from parent list of other clocks clk: at91: clk-sam9x60-pll: allow runtime changes for pll clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics clk: at91: clk-master: add 5th divisor for mck master clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT dt-bindings: clock: at91: add sama7g5 pll defines clk: at91: sama7g5: fix compilation error * clk-silabs: clk: si5351: Wait for bit clear after PLL reset
-
Stephen Boyd authored
- Support for SiFive FU740 PRCI - Add hardware enable information to clk_summary debugfs * clk-tegra: clk: tegra: Fix duplicated SE clock entry clk: tegra: bpmp: Clamp clock rates on requests clk: tegra: Do not return 0 on failure * clk-imx: (24 commits) clk: imx: scu: remove the calling of device_is_bound clk: imx: scu: Make pd_np with static keyword clk: imx8mq: drop of_match_ptr from of_device_id table clk: imx8mp: drop of_match_ptr from of_device_id table clk: imx8mn: drop of_match_ptr from of_device_id table clk: imx8mm: drop of_match_ptr from of_device_id table clk: imx: gate2: Remove unused variable ret clk: imx: gate2: Add locking in is_enabled op clk: imx: gate2: Add cgr_mask for more flexible number of control bits clk: imx: gate2: Check if clock is enabled against cgr_val clk: imx: gate2: Keep the register writing in on place clk: imx: gate2: Remove the IMX_CLK_GATE2_SINGLE_BIT special case clk: imx: scu: fix build break when compiled as modules clk: imx: remove redundant assignment to pointer np clk: imx: remove unneeded semicolon clk: imx: lpcg: add suspend/resume support clk: imx: clk-imx8qxp-lpcg: add runtime pm support clk: imx: lpcg: allow lpcg clk to take device pointer clk: imx: imx8qxp-lpcg: add parsing clocks from device tree clk: imx: scu: add suspend/resume support ... * clk-sifive: clk: sifive: Add clock enable and disable ops clk: sifive: Fix the wrong bit field shift clk: sifive: Add a driver for the SiFive FU740 PRCI IP block clk: sifive: Use common name for prci configuration clk: sifive: Extract prci core to common base dt-bindings: fu740: prci: add YAML documentation for the FU740 PRCI * clk-mediatek: clk: mediatek: Make mtk_clk_register_mux() a static function * clk-summary: clk: Add hardware-enable column to clk summary
-
Stephen Boyd authored
Merge branches 'clk-amlogic', 'clk-rockchip', 'clk-of', 'clk-freescale' and 'clk-unused' into clk-next - Replace clk-provider.h with of_clk.h when possible * clk-amlogic: clk: meson: g12a: add MIPI DSI Host Pixel Clock dt-bindings: clk: g12a-clkc: add DSI Pixel clock bindings clk: meson: enable building as modules clk: meson: Kconfig: fix dependency for G12A clk: meson: axg: add MIPI DSI Host clock clk: meson: axg: add Video Clocks dt-bindings: clk: axg-clkc: add MIPI DSI Host clock binding dt-bindings: clk: axg-clkc: add Video Clocks * clk-rockchip: clk: rockchip: fix i2s gate bits on rk3066 and rk3188 clk: rockchip: add CLK_SET_RATE_PARENT to sclk for rk3066a i2s and uart clocks clk: rockchip: Remove redundant null check before clk_prepare_enable clk: rockchip: Add appropriate arch dependencies * clk-of: xtensa: Replace <linux/clk-provider.h> by <linux/of_clk.h> sh: boards: Replace <linux/clk-provider.h> by <linux/of_clk.h> * clk-freescale: clk: fsl-flexspi: new driver dt-bindings: clock: document the fsl-flexspi-clk device clk: divider: add devm_clk_hw_register_divider_table() clk: qoriq: provide constants for the type clk: fsl-sai: use devm_clk_hw_register_composite_pdata() clk: composite: add devm_clk_hw_register_composite_pdata() clk: fsl-sai: fix memory leak clk: qoriq: Add platform dependencies * clk-unused: clk: scpi: mark scpi_clk_match as maybe unused clk: pwm: drop of_match_ptr from of_device_id table
-
Stephen Boyd authored
Merge branches 'clk-doc', 'clk-qcom', 'clk-simplify', 'clk-hw', 'clk-renesas' and 'clk-samsung' into clk-next - Camera clks on Qualcomm SC7180 SoCs - GCC and RPMh clks on Qualcomm SDX55 SoCs - RPMh clks on Qualcomm SM8350 SoCs - LPASS clks on Qualcomm SM8250 SoCs - Add devm variant of clk_notifier_register() - Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw * clk-doc: clk: fix a kernel-doc markup * clk-qcom: (27 commits) clk: qcom: rpmh: add support for SM8350 rpmh clocks dt-bindings: clock: Add RPMHCC bindings for SM8350 clk: qcom: lpasscc: Introduce pm autosuspend for SC7180 clk: qcom: gcc-sc7180: Add 50 MHz clock rate for SDC2 clk: qcom: gcc-sc7180: Use floor ops for sdcc clks clk: qcom: Add GDSC support for SDX55 GCC dt-bindings: clock: Add GDSC in SDX55 GCC clk: qcom: Add support for SDX55 RPMh clocks dt-bindings: clock: Introduce RPMHCC bindings for SDX55 clk: qcom: Add SDX55 GCC support dt-bindings: clock: Add SDX55 GCC clock bindings clk: qcom: Kconfig: Fix spelling mistake "dyanmic" -> "dynamic" clk: qcom: rpmh: Add CE clock on sdm845. dt-bindings: clock: Add entry for crypto engine RPMH clock resource clk: qcom: dispcc-sm8250: handle MMCX power domain clk: qcom: camcc-sc7180: Use runtime PM ops instead of clk ones clk: qcom: lpass-sc7180: Clean up on error in lpass_sc7180_init() clk: qcom: Add support to LPASS AON_CC Glitch Free Mux clocks clk: qcom: Add support to LPASS AUDIO_CC Glitch Free Mux clocks dt-bindings: clock: Add support for LPASS Always ON Controller ... * clk-simplify: clk: remove unneeded dead-store initialization * clk-hw: clk: meson: g12: use devm variant to register notifiers clk: add devm variant of clk_notifier_register clk: meson: g12: drop use of __clk_lookup() clk: add api to get clk consumer from clk_hw clk: avoid devm_clk_release name clash * clk-renesas: dt-bindings: clock: renesas: rcar-usb2-clock-sel: Convert bindings to json-schema clk: renesas: sh73a0: Stop using __raw_*() I/O accessors clk: renesas: r8a774c0: Add RPC clocks clk: renesas: r8a779a0: Fix R and OSC clocks clk: renesas: cpg-mssr: fix kerneldoc of cpg_mssr_priv clk: renesas: rcar-usb2-clock-sel: Replace devm_reset_control_array_get() clk: renesas: r8a774b1: Add RPC clocks clk: renesas: r8a774a1: Add RPC clocks clk: renesas: r8a779a0: Add VIN clocks clk: renesas: r8a779a0: Add CSI4[0-3] clocks MAINTAINERS: Update git repo for Renesas clock drivers clk: renesas: r8a779a0: Make rcar_r8a779a0_cpg_clk_register() static clk: renesas: rcar-gen3: Remove stp_ck handling for SDHI * clk-samsung: clk: samsung: Prevent potential endless loop in the PLL ops clk: samsung: Allow compile testing of Exynos, S3C64xx and S5Pv210
-
- 19 Dec, 2020 13 commits
-
-
Sascha Hauer authored
Documentation states that SI5351_PLL_RESET_B and SI5351_PLL_RESET_A bits are self clearing bits, so wait until they are cleared before continuing. This fixes a case when the clock doesn't come up properly after a PLL reset. It worked properly when the frequency was below 900MHz, but with 900MHz it only works when we are waiting for the bit to clear. Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Link: https://lore.kernel.org/r/20201130091033.1687-1-s.hauer@pengutronix.deSigned-off-by:
Stephen Boyd <sboyd@kernel.org>
-
Alexandre Belloni authored
The sam9x60 doesn't have the MOSCXTBY bit to enable the crystal oscillator bypass. Fixes: 01e2113d ("clk: at91: add sam9x60 pmc driver") Reported-by:
Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201202125816.168618-1-alexandre.belloni@bootlin.comReviewed-by:
-
Claudiu Beznea authored
Register CPU clock as being the master clock prescaler. This would be used by DVFS. The block schema of SAMA7G5's PMC contains also a divider between master clock prescaler and CPU (PMC_CPU_RATIO.RATIO) but the frequencies supported by SAMA7G5 could be directly received from CPUPLL + master clock prescaler and the extra divider would do no work in case it would be enabled. Signed-off-by:
-
Claudiu Beznea authored
Re-factor master clock driver by splitting it into 2 clocks: prescaller and divider clocks. Based on registered clock flags the prescaler's rate could be changed at runtime. This is necessary for platforms supporting DVFS (e.g. SAMA7G5) where master clock could be changed at run-time. Signed-off-by:
-
Claudiu Beznea authored
Since CPU PLL feeds both CPU clock and MCK0, MCK0 cannot go higher than 200MHz and MCK0 maximum prescaller is 5 limit the CPU PLL at 1GHz to avoid MCK0 overclocking while CPU PLL is changed by DVFS. Signed-off-by:
-
Claudiu Beznea authored
On SAMA7G5 CPU clock is changed at run-time by DVFS. Since MCK0 and CPU clock shares the same parent clock (CPUPLL clock) the MCK0 is also changed by DVFS to avoid over/under clocking of MCK0 consumers. The lower limit is changed to be able to set MCK0 accordingly by DVFS. Signed-off-by:
-
Claudiu Beznea authored
MCK0 is changed at runtime by DVFS. Due to this, since not all IPs are glitch free aware at MCK0 changes, remove MCK0 from parent list of other clocks (e.g. generic clock, programmable/system clock, MCKX). Signed-off-by:
-
Claudiu Beznea authored
Allow runtime frequency changes for PLLs registered with proper flags. This is necessary for CPU PLL on SAMA7G5 which is used by DVFS. Signed-off-by:
-
Eugen Hristev authored
This SoC has the 5th divisor for the mck0 master clock. Adapt the characteristics accordingly. Reported-by:
Mihai Sain <mihai.sain@microchip.com> Signed-off-by:
Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by:
-
Eugen Hristev authored
clk-master can have 5 divisors with a field width of 3 bits on some products. Change the mask and number of divisors accordingly. Reported-by:
-
Eugen Hristev authored
Allow SYSPLL and CPUPLL to be referenced as a PMC_TYPE_CORE clock from phandle in DT. Suggested-by:
-
Eugen Hristev authored
Add SAMA7G5 specific PLL defines to be referenced in a phandle as a PMC_TYPE_CORE clock. Suggested-by:
-
Claudiu Beznea authored
pmc_data_allocate() has been changed. pmc_data_free() was removed. Adapt the code taking this into consideration. With this the programmable clocks were also saved in sama7g5_pmc so that they could be later referenced. Fixes: cb783bbb ("clk: at91: sama7g5: add clock support for sama7g5") Signed-off-by:
Tudor Ambarus <tudor.ambarus@microchip.com> Tested-by:
-
- 17 Dec, 2020 8 commits
-
-
Maxime Ripard authored
The clk_set_rate "range" functions don't have any tracepoints even though it might be useful. Add some. Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20201207105050.2096917-1-maxime@cerno.tech [sboyd@kernel.org: Reword commit text] Signed-off-by:
-
Alexandru Ardelean authored
The change is mostly cosmetic. No functional changes. Since the driver now uses of_device_get_match_data() to obtain some driver specific info, there is no need to define the OF table before the probe function. Signed-off-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Link: https://lore.kernel.org/r/20201203074037.26940-2-alexandru.ardelean@analog.comSigned-off-by:
-
Alexandru Ardelean authored
Up until the these limits were global/hard-coded, since they are typically limits of the fabric. However, since this is an FPGA generated clock, this may run on setups where one clock is on a fabric, and another one synthesized on another fabric connected via PCIe (or some other inter-connect, and then these limits need to be adjusted for each instance of the AXI CLKGEN. This change wraps the current constants in 'axi_clkgen_limits' struct and the 'axi_clkgen' instance keeps a copy of these limits, which is initialized at probe from the default limits. The limits are stored on the device-tree OF table, so that we can adjust them via the compatible string. Signed-off-by:
-
Alexandru Ardelean authored
This change converts the old binding for the AXI clkgen driver to a yaml format. As maintainers, added: - Lars-Peter Clausen <lars@metafoo.de> - as original author of driver & binding - Michael Hennerich <michael.hennerich@analog.com> - as supporter of Analog Devices drivers Acked-by:
Michael Hennerich <michael.hennerich@analog.com> Acked-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
David Shah authored
Having the ABE DPLL ref and bypass muxes set to different inputs was causing the DPLL not to lock when TIMER8 was used, as it is in the Pyra for the backlight. This patch fixes this by setting abe_dpll_bypass_clk_mux to sys_32k_ck in omap5xxx_dt_clk_init. A similar patch may also be needed for OMAP44xx which has similar code in omap4xxx_dt_clk_init, but I have not added this as I have no hardware to test on. Signed-off-by:
David Shah <dave@ds0.me> Signed-off-by:
H. Nikolaus Schaller <hns@goldelico.com> Link: https://lore.kernel.org/r/1d3abe2512054866cc2ea7b2592238f4fa06502a.1607253531.git.hns@goldelico.comAcked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Zhang Qilong authored
If clk_register fails, we should goto free branch before function returns to prevent memleak. Fixes: 163152cb ("clk: ti: Add support for FAPLL on dm816x") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Zhang Qilong <zhangqilong3@huawei.com> Link: https://lore.kernel.org/r/20201113131623.2098222-1-zhangqilong3@huawei.comAcked-by:
-
Dmitry Osipenko authored
Add "hardware enable" column to the clk summary in order to show actual hardware enable-state of all clocks. The possible states are "Y/N/?", where question mark means that state is unknown, i.e. clock isn't a mux and clk-driver doesn't support is_enabled() callback for this clock. In conjunction with clk_ignore_unused, this tells us what unused clocks are left enabled after bootloader. This is also a useful aid for debugging interactions with firmware which changes clock states without notifying kernel. Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Link: https://lore.kernel.org/r/20201115203432.13934-1-digetx@gmail.comSigned-off-by:
-
Weiyi Lu authored
mtk_clk_register_mux() should be a static function Fixes: a3ae5499 ("clk: mediatek: Add new clkmux register API") Signed-off-by:
Weiyi Lu <weiyi.lu@mediatek.com> Link: https://lore.kernel.org/r/1605256192-31307-1-git-send-email-weiyi.lu@mediatek.comSigned-off-by:
-
- 16 Dec, 2020 6 commits
-
-
Pragnesh Patel authored
Add new functions "sifive_prci_clock_enable(), sifive_prci_clock_disable() and sifive_clk_is_enabled()" to enable or disable the PRCI clock Signed-off-by:
Pragnesh Patel <pragnesh.patel@sifive.com> Tested-by:
Zong Li <zong.li@sifive.com> Link: https://lore.kernel.org/r/20201209094916.17383-6-zong.li@sifive.comSigned-off-by:
-
Zong Li authored
The clk enable bit should be 31 instead of 24. Signed-off-by:
-
Zong Li authored
Add driver code for the SiFive FU740 PRCI IP block. This IP block handles reset and clock control for the SiFive FU740 device and implements SoC-level clock tree controls and dividers. The link of unmatched as follow, and the U740-C000 manual would be present in the same page as soon. https://www.sifive.com/boards/hifive-unmatched This driver contains bug fixes and contributions from Henry Styles <hes@sifive.com> Erik Danie <erik.danie@sifive.com> Pragnesh Patel <pragnesh.patel@sifive.com> Signed-off-by:
Palmer Dabbelt <palmerdabbelt@google.com> Cc: Henry Styles <hes@sifive.com> Cc: Erik Danie <erik.danie@sifive.com> Cc: Pragnesh Patel <pragnesh.patel@sifive.com> Link: https://lore.kernel.org/r/20201209094916.17383-4-zong.li@sifive.com [sboyd@kernel.org: Include header to silence sparse] Signed-off-by:
-
Zong Li authored
Use generic name CLK_SIFIVE_PRCI instead of CLK_SIFIVE_FU540_PRCI. This patch is prepared for fu740 support. Signed-off-by:
-
Zong Li authored
Extract common core of prci driver to an independent file, it could allow other chips to reuse it. Separate SoCs-dependent code 'fu540' from prci core, then we can easily add 'fu740' later. Almost these changes are code movement. The different is adding the private data for each SoC use, so it needs to get match data in probe callback function, then use the data for initialization. Signed-off-by:
-
Zong Li authored
Add YAML DT binding documentation for the SiFive FU740 PRCI. The link of unmatched board as follow, the U740-C000 manual would be present in the same page later. https://www.sifive.com/boards/hifive-unmatched Passes dt_binding_check. Signed-off-by:
-
- 10 Dec, 2020 9 commits
-
-
Stephen Boyd authored
Merge tag 'renesas-clk-for-v5.11-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-renesas Pull Renesas clk driver updates from Geert Uytterhoeven: - Update git repo branch for Renesas clock drivers - Add camera (CSI) and video-in (VIN) clocks on R-Car V3U - Add RPC (QSPI/HyperFLASH) clocks on RZ/G2M, RZ/G2N, and RZ/G2E - Stop using __raw_*() I/O accessors - One more conversion of DT bindings to json-schema - Minor fixes and improvements * tag 'renesas-clk-for-v5.11-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers: dt-bindings: clock: renesas: rcar-usb2-clock-sel: Convert bindings to json-schema clk: renesas: sh73a0: Stop using __raw_*() I/O accessors clk: renesas: r8a774c0: Add RPC clocks clk: renesas: r8a779a0: Fix R and OSC clocks clk: renesas: cpg-mssr: fix kerneldoc of cpg_mssr_priv clk: renesas: rcar-usb2-clock-sel: Replace devm_reset_control_array_get() clk: renesas: r8a774b1: Add RPC clocks clk: renesas: r8a774a1: Add RPC clocks clk: renesas: r8a779a0: Add VIN clocks clk: renesas: r8a779a0: Add CSI4[0-3] clocks MAINTAINERS: Update git repo for Renesas clock drivers clk: renesas: r8a779a0: Make rcar_r8a779a0_cpg_clk_register() static clk: renesas: rcar-gen3: Remove stp_ck handling for SDHI
-
Stephen Boyd authored
Merge tag 'clk-imx-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-imx Pull i.MX clk driver updates from Shawn Guo: - A series from Abel Vesa to improve clk-gate2 driver and make it more flexible. - A patch set from Dong Aisheng to add a new two cells binding for SCU clocks, so that IMX SCU based platforms like MX8QM and MX8QXP can be supported with SS (Subsystems). - Drop of_match_ptr from of_device_id table for i.MX8 clock drivers, as they can only be probed from device tree. - Other small cosmetic changes. * tag 'clk-imx-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (24 commits) clk: imx: scu: remove the calling of device_is_bound clk: imx: scu: Make pd_np with static keyword clk: imx8mq: drop of_match_ptr from of_device_id table clk: imx8mp: drop of_match_ptr from of_device_id table clk: imx8mn: drop of_match_ptr from of_device_id table clk: imx8mm: drop of_match_ptr from of_device_id table clk: imx: gate2: Remove unused variable ret clk: imx: gate2: Add locking in is_enabled op clk: imx: gate2: Add cgr_mask for more flexible number of control bits clk: imx: gate2: Check if clock is enabled against cgr_val clk: imx: gate2: Keep the register writing in on place clk: imx: gate2: Remove the IMX_CLK_GATE2_SINGLE_BIT special case clk: imx: scu: fix build break when compiled as modules clk: imx: remove redundant assignment to pointer np clk: imx: remove unneeded semicolon clk: imx: lpcg: add suspend/resume support clk: imx: clk-imx8qxp-lpcg: add runtime pm support clk: imx: lpcg: allow lpcg clk to take device pointer clk: imx: imx8qxp-lpcg: add parsing clocks from device tree clk: imx: scu: add suspend/resume support ...
-
Dmitry Osipenko authored
The periph_clks[] array contains duplicated entry for Security Engine clock which was meant to be defined for T210, but it wasn't added properly. This patch corrects the T210 SE entry and fixes the following error message on T114/T124: "Tegra clk 127: register failed with -17". Fixes: dc37fec4 ("clk: tegra: periph: Add new periph clks and muxes for Tegra210") Tested-by Nicolas Chauvet <kwizart@gmail.com> Reported-by Nicolas Chauvet <kwizart@gmail.com> Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Vinod Koul authored
This adds the RPMH clocks present in SM8350 SoC Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20201208064702.3654324-3-vkoul@kernel.org [sboyd@kernel.org: Move sdx55 to the right place] Signed-off-by:
-
Vinod Koul authored
Add bindings and update documentation for clock rpmh driver on SM8350. Reviewed-by:
-
Taniya Das authored
The LPASSCC driver's suspend/resume is invoked multiple number of times and thus allow the device to autosuspend for 500ms. Signed-off-by:
Taniya Das <tdas@codeaurora.org> Link: https://lore.kernel.org/r/1605890417-721-1-git-send-email-tdas@codeaurora.orgSigned-off-by:
-
Douglas Anderson authored
50 MHz is an incredibly common clock rate for SD cards to run at. It's "high speed" mode in SD (not very fast these days, but it used to be) or: #define HIGH_SPEED_MAX_DTR 50000000 If we don't support this then older "high speed" cards can only run at 25 MHz or at half their normal speed. There doesn't seem to be any reason to skip this clock rate, so add it. Fixes: 17269568 ("clk: qcom: Add Global Clock controller (GCC) driver for SC7180") Signed-off-by:
Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20201210102234.2.I26dcc0cee374f5571d9929c9985f463773167e68@changeidReviewed-by:
-
Douglas Anderson authored
I would repeat the same commit message that was in commit 5e4b7e82 ("clk: qcom: gcc-sdm845: Use floor ops for sdcc clks") but it seems silly to do so when you could just go read that commit. NOTE: this is actually extra terrible because we're missing the 50 MHz rate in the table (see the next patch AKA ("clk: qcom: gcc-sc7180: Add 50 MHz clock rate for SDC2")). That means then when you run an older SD card it'll try to clock it at 100 MHz when it's only specced to run at 50 MHz max. As you can probably guess that doesn't work super well. Signed-off-by:
-
Krzysztof Kozlowski authored
The scpi_clk_match (struct of_device_id) is referenced only with CONFIG_OF builds thus mark it as __maybe_unused: drivers/clk/clk-scpi.c:132:34: warning: ‘scpi_clk_match’ defined but not used [-Wunused-const-variable=] Signed-off-by:Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20201103162435.13689-8-krzk@kernel.orgAcked-by:
Sudeep Holla <sudeep.holla@arm.com> Signed-off-by:
-
