- 21 Feb, 2007 40 commits
-
-
Marcel Siegert authored
Arjan van de Ven <arjan@infradead.org> reported an illegal re-usage of the fileoperations struct if more than one dvb device (e.g. frontend) is present. This patch fixes this issue. It allocates a new fileoperations struct each time a device is registered and copies the default template fileops. Signed-off-by:
Marcel Siegert <mws@linuxtv.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@infradead.org>
-
Chris Rankin authored
The work item function is dvb_usb_read_remote_control(): INIT_WORK(&d->rc_query_work, dvb_usb_read_remote_control, d); and the last piece of work it does is: schedule_delayed_work(&d->rc_query_work,msecs_to_jiffies(d->props.rc_interval)); Hence you need to call "cancel_rearming_delayed_work()" and not "cancel_delayed_work()", correct? I certainly haven't seen this oops reoccur since I applied this patch. Signed-off-by:Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Antti Palosaari authored
This patch adds calls to i2c_gate_ctrl in the qt1010 dvb tuner module, while removing the temporary hack in au6610 and gl861. Tested successfully against fi-Oulu frequencies with MSI Megasky 580 GL861 and Sigmatek DVB-110 AU6610. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Antti Palosaari authored
gl861: (MSI Megasky) - hack for enable ZL10353 / QT1010 I2C gate - use new QT1010 module instead of old code au6610: (Sigmatek DVB-110) - hack for enable ZL10353 / QT1010 I2C gate - use new QT1010 module instead of old code Tested successfully with au6610 and gl861 devices against fi-Yllas frequencies. Now it locks perfectly with both devices. There is a "hack" to enable probable i2c gate in zl10535 demodulator. QT1010 doesn't respond to any i2c messages before we write 0x1a to demodulator register 0x62. In my understanding this should be fixed to demodulator code. Signed-off-by:
-
Antti Palosaari authored
This patch adds driver for Sigmatek DVB-110 USB DVB-T stick. Stick has based on hardware of Qtuantek QT1010 tuner, Zarlink ZL10353 (Intel CE 6353) demodulator and Alcor Micro AU6610 DVB-T USB controller. HW is rather similar as used in MSI Megasky GL861. Currently, the driver works only in USB 2.0. In my understanding USB 1.1 is also supported by hw but I cannot test it due to lack of USB 1.1 port. Device supports only isochronous mode transfers. There is also eeprom in usb controller(at least in address range 0x80 - 0xbf) for storing data, eg. firmware. Anyway, firmware loading is not used / required by the device. There seems to be at least one unknown I2C device in address 0xa0, probably remote control or GPIO. Windows drivers reads registers from 0x00 to 0x07 from this unknown address. Driver is based on gl861 module. Tuner has a lot of problems to lock with megasky qt1010 module with this hardware with some broadcasting standards. Signed-off-by:
-
Carl Lundqvist authored
- use parallel_ts - Now this driver works. - correct typo in MODULE_VERSION Signed-off-by:
Carl Lundqvist <comabug@gmail.com> Signed-off-by:
-
Michael Krufky authored
remove unneeded declaration of .generic_bulk_ctrl_endpoint generic_bulk_ctrl_endpoint isn't being used in this device, so this is not needed here. Signed-off-by:
-
Jan Nijs authored
The megasky 580 based on gl861 has three endpoints: - 0x81 BULK/ISOC IN MPEG2 TS - 0x83 INT IN remote control receiver - 0x02 BULK OUT bulk control endpoint It doesn't look like the bulk endpoint is used, but better to have the correct one in the config. Signed-off-by:
Jan Nijs <jan.nijs@scarlet.be> Signed-off-by:
-
Jan Nijs authored
This patch moves the DVB_USB_IS_AN_I2C_ADAPTER flag from the adapter properties to the device properties. Without this patch I get an OOPS when the gl861 driver tries to access any registers. Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
The gl861_tuner_attach function is not specific to this device. This patch removes gl861_tuner_attach, and replaces it with qt1010_tuner_attach from the qt1010 header file. Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
enclose disabled code inside an #if 0 block, instead of /* comments */ Signed-off-by:
-
Michael Krufky authored
Rename driver_name from "gl861" to "dvb_usb_gl861" Signed-off-by:
-
Michael Krufky authored
The author's email address is already in the MODULE_AUTHOR field. This patch adds his name as well. Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Carl Lundqvist authored
This patch adds support for MSI Mega Sky 580 / GL861 DVB-T USB2.0 Except for the 2 lines added to zl10353.c, zl10353_reset_attach needs to be changed. If I read the code correctly setting parallel_ts will take care of the 3rd byte, but the 2nd byte needs to be 0x0b instead of 0x03 too. I guess these changes needs to be done only for this device, not sure how to do that. The zl10353 changes have been split apart from this patch, into the next patch, soon to follow. Signed-off-by:
-
Chris Pascoe authored
Update the descriptions of "discovered" registers on the zl10353, using the equivalaent mt352 register names. Signed-off-by:
Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by:
-
Antti Palosaari authored
Implement trl nominal rate calculation to Zarlink ZL10353 demod, based on calculation used in Zarlink MT352. This adds support for 6 and 8MHz bandwidth transponders. Signed-off-by:
-
Antti Palosaari authored
Implement I2C gate control for Megasky GL861 and SigmaTek AU6610 support. Signed-off-by:
-
Chris Pascoe authored
After studying many hours worth of register dumps of MT352 and ZL10353 fed with identically damaged RF signals I have made an educated guess at which registers contain the AGC level, bit error rate and uncorrectable error count values. Implement the IOCTLs that return these values to userspace. Signed-off-by:
-
Mike Isely authored
The pvrusb2 driver previously rejected encoder firmware whose size was not a multiple of 8192. But this is a false check because it's possible to find cx23416 firmware whose size doesn't conform to this limit. So change the firmware loader implementation to be more forgiving of the image size. Signed-off-by:
Mike Isely <isely@pobox.com> Signed-off-by:
-
Mike Isely authored
Signed-off-by:
-
akpm@linux-foundation.org authored
avoid double-up(), pointed out by Oliver. Signed-off-by:
Oliver Endriss <o.endriss@gmx.de> Signed-off-by:
-
Herbert Poetzl authored
dvb kernel_thread to kthread API port. It is running fine here, including module load/unload and software suspend (which doesn't work as expected with or without this patch :). I didn't convert the dvb_ca_en50221 as I do not have such an interface, but if the conversion process is fine with the v4l-dvb maintainers, it should not be a problem to send a patch for that too ... Acked-by:
Herbert Poetzl <herbert@13thfloor.at> Signed-off-by:
-
Thierry MERLE authored
- usb alternate selection modified to get the biggest endpoint packet size. - fix sysfs get values for brightness/contrast/hue/saturation Signed-off-by:
Thierry MERLE <thierry.merle@free.fr> Signed-off-by:
-
Thierry MERLE authored
- fix decoder route output - dynamic frame buffer allocation Signed-off-by:
-
Adrian Bunk authored
Signed-off-by:
Adrian Bunk <bunk@stusta.de> Signed-off-by:
-
Michael Schimek authored
videodev2.h contains just the V4L2 API structs and defines. By allowing this header file to be dual GPL/BSD will enable sharing userspace apps between Linux and *BSD systems. It will also allow developing newer BSD licensed drivers that can be shared on Linux and *BSD. It should be noticed that most of the current V4L drivers, and v4l core itself are GPL only. This won't be changed by this patch. Signed-off-by:
Michael H. Schimek <mschimek@gmx.at> Signed-off-by:
Gerd Hoffmann <kraxel@suse.de> Signed-off-by:
Bill Dirks <bill@thedirks.org> Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
Martin Rubli <mrubli@gmx.net> Signed-off-by:
-
Ahmed S. Darwish authored
Use ARRAY_SIZE macro already defined in kernel.h Signed-off-by:
Ahmed S. Darwish <darwish.07@gmail.com> Acked-by:
Manu Abraham <manu@linuxtv.org> Signed-off-by:
-
Richard Knutsson authored
Signed-off-by:
Richard Knutsson <ricknu-0@student.ltu.se> Signed-off-by:
-
Adrian Bunk authored
This patch removes the unused struct radionorms. Signed-off-by:
-
Jonathan Corbet authored
Quiet a spurious gcc warning. Signed-off-by:
Jonathan Corbet <corbet@lwn.net> Signed-off-by:
-
Richard Knutsson authored
Signed-off-by:
-
Andrew Morton authored
m68k allmodconfig: drivers/media/video/video-buf.c: In function 'videobuf_queue_pci': drivers/media/video/video-buf.c:396: error: 'pci_map_sg' undeclared (first use in this function) drivers/media/video/video-buf.c:396: error: (Each undeclared identifier is reported only once drivers/media/video/video-buf.c:396: error: for each function it appears in.) drivers/media/video/video-buf.c:399: error: 'pci_dma_sync_sg_for_cpu' undeclared (first use in this function) drivers/media/video/video-buf.c:401: error: 'pci_unmap_sg' undeclared (first use in this function) drivers/media/video/video-buf.c: In function 'videobuf_pci_dma_map': Acked-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Adrian Bunk authored
This patch makes four needlessly global functions static. Signed-off-by:
-
