For z/VM NICs, qeth needs to consider which of the three CCW devices in
an MPC group it uses for requesting a managed MAC address.

On the Base device, the hypervisor returns a default MAC which is
pre-assigned when creating the NIC (this MAC is also returned by the
READ MAC primitive). Querying any other device results in the allocation
of an additional MAC address.

For consistency with READ MAC and to avoid using up more addresses than
necessary, it is preferable to use the NIC's default MAC. So switch the
the diag26c over to using a NIC's Read device, which should always be
identical to the Base device.

Fixes: ec61bd2f ("s390/qeth: use diag26c to get MAC address on L2")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Submitting a cmd IO request (usually on the WRITE device, but for IDX
also on the READ device) is currently done with ccw_device_start()
and a manual timeout in the caller.
On timeout, the caller cleans up the related resources (eg. IO buffer).
But 1) the IO might still be active and utilize those resources, and
    2) when the IO completes, qeth_irq() will attempt to clean up the
       same resources again.

Instead of introducing additional resource locking, switch to
ccw_device_start_timeout() to ensure IO termination after timeout, and
let the IRQ handler alone deal with cleaning up after a request.

This also removes a stray write->irq_pending reset from
clear_ipacmd_list(). The routine doesn't terminate any pending IO on
the WRITE device, so this should be handled properly via IO timeout
in the IRQ handler.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When changing the MAC address on a L2 qeth device, current code first
unregisters the old address, then registers the new one.
If HW rejects the new address (or the IO fails), the device ends up with
no operable address at all.

Re-order the code flow so that the old address only gets dropped if the
new address was registered successfully. While at it, add logic to catch
some corner-cases.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Creating the global workqueue during driver init may fail, deal with it.
Also, destroy the created workqueue on any subsequent error.

Fixes: 0f54761d ("qeth: Support VEPA mode")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For control IO, qeth currently tracks the index of the buffer that it
expects to complete the next IO on each qeth_channel. If the channel
presents an IRQ while this buffer has not yet completed, no completion
processing for _any_ completed buffer takes place.
So if the 'next buffer' is skipped for any sort of reason* (eg. when it
is released due to error conditions, before the IO is started), the
buffer obviously won't switch to PROCESSED until it is eventually
allocated for a _different_ IO and completes.
Until this happens, all completion processing on that channel stalls
and pending requests possibly time out.

As a fix, remove the whole 'next buffer' logic and simply process any
IO buffer right when it completes. A channel will never have more than
one IO pending, so there's no risk of processing out-of-sequence.

*Note: currently just one location in the code really handles this problem,
       by advancing the 'next' index manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to check both return code fields before(!) processing the
command response. Otherwise we risk operating on invalid data.

This matches an earlier fix for SETASSPARMS commands, see
commit ad3cbf61 ("s390/qeth: fix error handling in checksum cmd callback").
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull thermal fixes from Eduardo Valentin:
 "A couple of fixes for the thermal subsystem"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  dt-bindings: thermal: Remove "cooling-{min|max}-level" properties
  dt-bindings: thermal: remove no longer needed samsung thermal properties

Pull MMC fixes from Ulf Hansson:
 "A couple of MMC host fixes:

   - sdhci-pci: Fixup tuning for AMD for eMMC HS200 mode

   - renesas_sdhi_internal_dmac: Avoid data corruption by limiting
     DMA RX"

* tag 'mmc-v4.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs
  mmc: sdhci-pci: Only do AMD tuning for HS200

Pull MD fixes from Shaohua Li:
 "Three small fixes for MD:

   - md-cluster fix for faulty device from Guoqing

   - writehint fix for writebehind IO for raid1 from Mariusz

   - a live lock fix for interrupted recovery from Yufen"

* tag 'md/4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  raid1: copy write hint from master bio to behind bio
  md/raid1: exit sync request if MD_RECOVERY_INTR is set
  md-cluster: don't update recovery_offset for faulty device

In do_mount() when the MS_* flags are being converted to MNT_* flags,
MS_RDONLY got accidentally convered to SB_RDONLY.

Undo this change.

Fixes: e462ec50 ("VFS: Differentiate mount flags (MS_*) from internal superblock flags")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

AFS server records get removed from the net->fs_servers tree when
they're deleted, but not from the net->fs_addresses{4,6} lists, which
can lead to an oops in afs_find_server() when a server record has been
removed, for instance during rmmod.

Fix this by deleting the record from the by-address lists before posting
it for RCU destruction.

The reason this hasn't been noticed before is that the fileserver keeps
probing the local cache manager, thereby keeping the service record
alive, so the oops would only happen when a fileserver eventually gets
bored and stops pinging or if the module gets rmmod'd and a call comes
in from the fileserver during the window between the server records
being destroyed and the socket being closed.

The oops looks something like:

  BUG: unable to handle kernel NULL pointer dereference at 000000000000001c
  ...
  Workqueue: kafsd afs_process_async_call [kafs]
  RIP: 0010:afs_find_server+0x271/0x36f [kafs]
  ...
  Call Trace:
   afs_deliver_cb_init_call_back_state3+0x1f2/0x21f [kafs]
   afs_deliver_to_call+0x1ee/0x5e8 [kafs]
   afs_process_async_call+0x5b/0xd0 [kafs]
   process_one_work+0x2c2/0x504
   worker_thread+0x1d4/0x2ac
   kthread+0x11f/0x127
   ret_from_fork+0x24/0x30

Fixes: d2ddc776 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Unbalanced refcounting in TIPC, from Jon Maloy.

 2) Only allow TCP_MD5SIG to be set on sockets in close or listen state.
    Once the connection is established it makes no sense to change this.
    From Eric Dumazet.

 3) Missing attribute validation in neigh_dump_table(), also from Eric
    Dumazet.

 4) Fix address comparisons in SCTP, from Xin Long.

 5) Neigh proxy table clearing can deadlock, from Wolfgang Bumiller.

 6) Fix tunnel refcounting in l2tp, from Guillaume Nault.

 7) Fix double list insert in team driver, from Paolo Abeni.

 8) af_vsock.ko module was accidently made unremovable, from Stefan
    Hajnoczi.

 9) Fix reference to freed llc_sap object in llc stack, from Cong Wang.

10) Don't assume netdevice struct is DMA'able memory in virtio_net
    driver, from Michael S. Tsirkin.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
  net/smc: fix shutdown in state SMC_LISTEN
  bnxt_en: Fix memory fault in bnxt_ethtool_init()
  virtio_net: sparse annotation fix
  virtio_net: fix adding vids on big-endian
  virtio_net: split out ctrl buffer
  net: hns: Avoid action name truncation
  docs: ip-sysctl.txt: fix name of some ipv6 variables
  vmxnet3: fix incorrect dereference when rxvlan is disabled
  llc: hold llc_sap before release_sock()
  MAINTAINERS: Direct networking documentation changes to netdev
  atm: iphase: fix spelling mistake: "Tansmit" -> "Transmit"
  net: qmi_wwan: add Wistron Neweb D19Q1
  net: caif: fix spelling mistake "UKNOWN" -> "UNKNOWN"
  net: stmmac: Disable ACS Feature for GMAC >= 4
  net: mvpp2: Fix DMA address mask size
  net: change the comment of dev_mc_init
  net: qualcomm: rmnet: Fix warning seen with fill_info
  tun: fix vlan packet truncation
  tipc: fix infinite loop when dumping link monitor summary
  tipc: fix use-after-free in tipc_nametbl_stop
  ...

Pull vfs fixes from Al Viro:
 "Assorted fixes.

  Some of that is only a matter with fault injection (broken handling of
  small allocation failure in various mount-related places), but the
  last one is a root-triggerable stack overflow, and combined with
  userns it gets really nasty ;-/"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  Don't leak MNT_INTERNAL away from internal mounts
  mm,vmscan: Allow preallocating memory for register_shrinker().
  rpc_pipefs: fix double-dput()
  orangefs_kill_sb(): deal with allocation failures
  jffs2_kill_sb(): deal with failed allocations
  hypfs_kill_super(): deal with failed allocations

Merge tag 'ecryptfs-4.17-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull eCryptfs fixes from Tyler Hicks:
 "Minor cleanups and a bug fix to completely ignore unencrypted
  filenames in the lower filesystem when filename encryption is enabled
  at the eCryptfs layer"

* tag 'ecryptfs-4.17-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: don't pass up plaintext names when using filename encryption
  ecryptfs: fix spelling mistake: "cadidate" -> "candidate"
  ecryptfs: lookup: Don't check if mount_crypt_stat is NULL

 - isofs memory leak fix

 - two fsnotify fixes of event mask handling

 - udf fix of UTF-16 handling

 - couple other smaller cleanups

* tag 'for_v4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  udf: Fix leak of UTF-16 surrogates into encoded strings
  fs: ext2: Adding new return type vm_fault_t
  isofs: fix potential memory leak in mount option parsing
  MAINTAINERS: add an entry for FSNOTIFY infrastructure
  fsnotify: fix typo in a comment about mark->g_list
  fsnotify: fix ignore mask logic in send_to_group()
  isofs compress: Remove VLA usage
  fs: quota: Replace GFP_ATOMIC with GFP_KERNEL in dquot_init
  fanotify: fix logic of events on child

Pull HID updates from Jiri Kosina:

 - suspend/resume handling fix for Raydium I2C-connected touchscreen
   from Aaron Ma

 - protocol fixup for certain BT-connected Wacoms from Aaron Armstrong
   Skomra

 - battery level reporting fix on BT-connected mice from Dmitry Torokhov

 - hidraw race condition fix from Rodrigo Rivas Costa

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: i2c-hid: fix inverted return value from i2c_hid_command()
  HID: i2c-hid: Fix resume issue on Raydium touchscreen device
  HID: wacom: bluetooth: send exit report for recent Bluetooth devices
  HID: hidraw: Fix crash on HIDIOCGFEATURE with a destroyed device
  HID: input: fix battery level reporting on BT mice

Pull livepatching fix from Jiri Kosina:
 "Shadow variable API list_head initialization fix from Petr Mladek"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
  livepatch: Allow to call a custom callback when freeing shadow variables
  livepatch: Initialize shadow variables safely by a custom callback

Pull xen fixes from Juergen Gross:

 - some fixes of kmalloc() flags

 - one fix of the xenbus driver

 - an update of the pv sound driver interface needed for a driver which
   will go through the sound tree

* tag 'for-linus-4.17-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen: xenbus_dev_frontend: Really return response string
  xen/sndif: Sync up with the canonical definition in Xen
  xen: xen-pciback: Replace GFP_ATOMIC with GFP_KERNEL in pcistub_reg_add
  xen: xen-pciback: Replace GFP_ATOMIC with GFP_KERNEL in xen_pcibk_config_quirks_init
  xen: xen-pciback: Replace GFP_ATOMIC with GFP_KERNEL in pcistub_device_alloc
  xen: xen-pciback: Replace GFP_ATOMIC with GFP_KERNEL in pcistub_init_device
  xen: xen-pciback: Replace GFP_ATOMIC with GFP_KERNEL in pcistub_probe

Pull MIPS fixes from James Hogan:

 - io: Add barriers to read*() & write*()

 - dts: Fix boston PCI bus DTC warnings (4.17)

 - memset: Several corner case fixes (one 3.10, others longer)

* tag 'mips_fixes_4.17_1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
  MIPS: uaccess: Add micromips clobbers to bzero invocation
  MIPS: memset.S: Fix clobber of v1 in last_fixup
  MIPS: memset.S: Fix return of __clear_user from Lpartial_fixup
  MIPS: memset.S: EVA & fault support for small_memset
  MIPS: dts: Boston: Fix PCI bus dtc warnings:
  MIPS: io: Add barrier after register read in readX()
  MIPS: io: Prevent compiler reordering writeX()

Pull powerpc fixes from Michael Ellerman:

 - Fix an off-by-one bug in our alternative asm patching which leads to
   incorrectly patched code. This bug lay dormant for nearly 10 years
   but we finally hit it due to a recent change.

 - Fix lockups when running KVM guests on Power8 due to a missing check
   when a thread that's running KVM comes out of idle.

 - Fix an out-of-spec behaviour in the XIVE code (P9 interrupt
   controller).

 - Fix EEH handling of bridge MMIO windows.

 - Prevent crashes in our RFI fallback flush handler if firmware didn't
   tell us the size of the L1 cache (only seen on simulators).

Thanks to: Benjamin Herrenschmidt, Madhavan Srinivasan, Michael Neuling.

* tag 'powerpc-4.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/kvm: Fix lockups when running KVM guests on Power8
  powerpc/eeh: Fix enabling bridge MMIO windows
  powerpc/xive: Fix trying to "push" an already active pool VP
  powerpc/64s: Default l1d_size to 64K in RFI fallback flush
  powerpc/lib: Fix off-by-one in alternate feature patching

Pull s390 fixes and kexec-file-load from Martin Schwidefsky:
 "After the common code kexec patches went in via Andrew we can now push
  the architecture parts to implement the kexec-file-load system call.

  Plus a few more bug fixes and cleanups, this includes an update to the
  default configurations"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/signal: cleanup uapi struct sigaction
  s390: rename default_defconfig to debug_defconfig
  s390: remove gcov defconfig
  s390: update defconfig
  s390: add support for IBM z14 Model ZR1
  s390: remove couple of duplicate includes
  s390/boot: remove unused COMPILE_VERSION and ccflags-y
  s390/nospec: include cpu.h
  s390/decompressor: Ignore file vmlinux.bin.full
  s390/kexec_file: add generated files to .gitignore
  s390/Kconfig: Move kexec config options to "Processor type and features"
  s390/kexec_file: Add ELF loader
  s390/kexec_file: Add crash support to image loader
  s390/kexec_file: Add image loader
  s390/kexec_file: Add kexec_file_load system call
  s390/kexec_file: Add purgatory
  s390/kexec_file: Prepare setup.h for kexec_file_load
  s390/smsgiucv: disable SMSG on module unload
  s390/sclp: avoid potential usage of uninitialized value

We want it only for the stuff created by SB_KERNMOUNT mounts, *not* for
their copies.  As it is, creating a deep stack of bindings of /proc/*/ns/*
somewhere in a new namespace and exiting yields a stack overflow.

Cc: stable@kernel.org
Reported-by: Alexander Aring <aring@mojatatu.com>
Bisected-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Tested-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Tested-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Calling shutdown with SHUT_RD and SHUT_RDWR for a listening SMC socket
crashes, because
   commit 127f4970 ("net/smc: release clcsock from tcp_listen_worker")
releases the internal clcsock in smc_close_active() and sets smc->clcsock
to NULL.
For SHUT_RD the smc_close_active() call is removed.
For SHUT_RDWR the kernel_sock_shutdown() call is omitted, since the
clcsock is already released.

Fixes: 127f4970 ("net/smc: release clcsock from tcp_listen_worker")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some firmware images, the length of BNX_DIR_TYPE_PKG_LOG nvram type
could be greater than the fixed buffer length of 4096 bytes allocated by
the driver.  This was causing HWRM_NVM_READ to copy more data to the buffer
than the allocated size, causing general protection fault.

Fix the issue by allocating the exact buffer length returned by
HWRM_NVM_FIND_DIR_ENTRY, instead of 4096.  Move the kzalloc() call
into the bnxt_get_pkgver() function.

Fixes: 3ebf6f0a ("bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael S. Tsirkin says:

====================
virtio: ctrl buffer fixes

Here are a couple of fixes related to the virtio control buffer.
Lightly tested on x86 only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

offloads is a buffer in virtio format, should use
the __virtio64 tag.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Programming vids (adding or removing them) still passes
guest-endian values in the DMA buffer. That's wrong
if guest is big-endian and when virtio 1 is enabled.

Note: this is on top of a previous patch:
	virtio_net: split out ctrl buffer

Fixes: 9465a7a6 ("virtio_net: enable v1.0 support")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When sending control commands, virtio net sets up several buffers for
DMA. The buffers are all part of the net device which means it's
actually allocated by kvmalloc so it's in theory (on extreme memory
pressure) possible to get a vmalloc'ed buffer which on some platforms
means we can't DMA there.

Fix up by moving the DMA buffers into a separate structure.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When longer interface names are used, the action names exposed in
/proc/interrupts and /proc/irq/* maybe truncated. For example, when
using the predictable name algorithm in systemd on a HiSilicon D05,
I see:

  ubuntu@d05-3:~$  grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
  enahisic2i0-tx0
  enahisic2i0-tx1
  [...]
  enahisic2i0-tx8
  enahisic2i0-tx9
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1

Increase the max ring name length to allow for an interface name
of IFNAMSIZE. After this change, I now see:

  $ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
  enahisic2i0-tx0
  enahisic2i0-tx1
  enahisic2i0-tx2
  [...]
  enahisic2i0-tx8
  enahisic2i0-tx9
  enahisic2i0-tx10
  enahisic2i0-tx11
  enahisic2i0-tx12
  enahisic2i0-tx13
  enahisic2i0-tx14
  enahisic2i0-tx15
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The name of the following proc/sysctl entries were incorrectly
documented:

    /proc/sys/net/ipv6/conf/<interface>/max_dst_opts_number
    /proc/sys/net/ipv6/conf/<interface>/max_hbt_opts_number
    /proc/sys/net/ipv6/conf/<interface>/max_dst_opts_length
    /proc/sys/net/ipv6/conf/<interface>/max_hbt_length

Their name was set to the name of the symbol in the .data field of the
control table instead of their .proc name.
Signed-off-by: Olivier Gayot <olivier.gayot@sigexec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3_get_hdr_len() is used to calculate the header length which in
turn is used to calculate the gso_size for skb. When rxvlan offload is
disabled, vlan tag is present in the header and the function references
ip header from sizeof(ethhdr) and leads to incorrect pointer reference.

This patch fixes this issue by taking sizeof(vlan_ethhdr) into account
if vlan tag is present and correctly references the ip hdr.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Acked-by: Louis Luo <llouis@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot reported we still access llc->sap in llc_backlog_rcv()
after it is freed in llc_sap_remove_socket():

Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1b9/0x294 lib/dump_stack.c:113
 print_address_description+0x6c/0x20b mm/kasan/report.c:256
 kasan_report_error mm/kasan/report.c:354 [inline]
 kasan_report.cold.7+0x242/0x2fe mm/kasan/report.c:412
 __asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:430
 llc_conn_ac_send_sabme_cmd_p_set_x+0x3a8/0x460 net/llc/llc_c_ac.c:785
 llc_exec_conn_trans_actions net/llc/llc_conn.c:475 [inline]
 llc_conn_service net/llc/llc_conn.c:400 [inline]
 llc_conn_state_process+0x4e1/0x13a0 net/llc/llc_conn.c:75
 llc_backlog_rcv+0x195/0x1e0 net/llc/llc_conn.c:891
 sk_backlog_rcv include/net/sock.h:909 [inline]
 __release_sock+0x12f/0x3a0 net/core/sock.c:2335
 release_sock+0xa4/0x2b0 net/core/sock.c:2850
 llc_ui_release+0xc8/0x220 net/llc/af_llc.c:204

llc->sap is refcount'ed and llc_sap_remove_socket() is paired
with llc_sap_add_socket(). This can be amended by holding its refcount
before llc_sap_remove_socket() and releasing it after release_sock().

Reported-by: <syzbot+6e181fc95081c2cf9051@syzkaller.appspotmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Networking docs changes go through the networking tree, so patch the
MAINTAINERS file to direct authors to the right place.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This modem is embedded on dlink dwr-960 router.
The oem configuration states:

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1435 ProdID=d191 Rev=ff.ff
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Tested on openwrt distribution
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ACS Feature is currently enabled for GMAC >= 4 but the llc_snap status
is never checked in descriptor rx_status callback. This will cause
stmmac to always strip packets even that ACS feature is already
stripping them.

Lets be safe and disable the ACS feature for GMAC >= 4 and always strip
the packets for this GMAC version.

Fixes: 477286b5 ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PPv2 TX/RX descriptors uses 40bits DMA addresses, but 41 bits masks were
used (GENMASK_ULL(40, 0)).

This commit fixes that by using the correct mask.

Fixes: e7c5359f ("net: mvpp2: introduce PPv2.2 HW descriptors and adapt accessors")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The comment of dev_mc_init() is wrong. which use dev_mc_flush
instead of dev_mc_init.

Signed-off-by: Lianwen Sun <sunlw.fnst@cn.fujitsu.com
Signed-off-by: David S. Miller <davem@davemloft.net>

Early revisions of certain SoCs cannot do multiple DMA RX streams in
parallel. To avoid data corruption, only allow one DMA RX channel and
fall back to PIO, if needed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>