- 03 Aug, 2015 38 commits
-
-
Eryu Guan authored
commit 8974fec7 upstream. Currently ext4_ind_migrate() doesn't correctly handle a file which contains a hole at the beginning of the file. This caused the migration to be done incorrectly, and then if there is a subsequent following delayed allocation write to the "hole", this would reclaim the same data blocks again and results in fs corruption. # assmuing 4k block size ext4, with delalloc enabled # skip the first block and write to the second block xfs_io -fc "pwrite 4k 4k" -c "fsync" /mnt/ext4/testfile # converting to indirect-mapped file, which would move the data blocks # to the beginning of the file, but extent status cache still marks # that region as a hole chattr -e /mnt/ext4/testfile # delayed allocation writes to the "hole", reclaim the same data block # again, results in i_blocks corruption xfs_io -c "pwrite 0 4k" /mnt/ext4/testfile umount /mnt/ext4 e2fsck -nf /dev/sda6 ... Inode 53, i_blocks is 16, should be 8. Fix? no ... Signed-off-by:
Eryu Guan <guaneryu@gmail.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eryu Guan authored
commit d6f123a9 upstream. Currently the check in ext4_ind_migrate() is not enough before doing the real conversion: a) delayed allocated extents could bypass the check on eh->eh_entries and eh->eh_depth This can be demonstrated by this script xfs_io -fc "pwrite 0 4k" -c "pwrite 8k 4k" /mnt/ext4/testfile chattr -e /mnt/ext4/testfile where testfile has two extents but still be converted to non-extent based file format. b) only extent length is checked but not the offset, which would result in data lose (delalloc) or fs corruption (nodelalloc), because non-extent based file only supports at most (12 + 2^10 + 2^20 + 2^30) blocks This can be demostrated by xfs_io -fc "pwrite 5T 4k" /mnt/ext4/testfile chattr -e /mnt/ext4/testfile sync If delalloc is enabled, dmesg prints EXT4-fs warning (device dm-4): ext4_block_to_path:105: block 1342177280 > max in inode 53 EXT4-fs (dm-4): Delayed block allocation failed for inode 53 at logical offset 1342177280 with max blocks 1 with error 5 EXT4-fs (dm-4): This should not happen!! Data will be lost If delalloc is disabled, e2fsck -nf shows corruption Inode 53, i_size is 5497558142976, should be 4096. Fix? no Fix the two issues by a) forcing all delayed allocation blocks to be allocated before checking eh->eh_depth and eh->eh_entries b) limiting the last logical block of the extent is within direct map Signed-off-by:
-
Lukas Czerner authored
commit 9705acd6 upstream. On delalloc enabled file system on invalidatepage operation in ext4_da_page_release_reservation() we want to clear the delayed buffer and remove the extent covering the delayed buffer from the extent status tree. However currently there is a bug where on the systems with page size > block size we will always remove extents from the start of the page regardless where the actual delayed buffers are positioned in the page. This leads to the errors like this: EXT4-fs warning (device loop0): ext4_da_release_space:1225: ext4_da_release_space: ino 13, to_free 1 with only 0 reserved data blocks This however can cause data loss on writeback time if the file system is in ENOSPC condition because we're releasing reservation for someones else delayed buffer. Fix this by only removing extents that corresponds to the part of the page we want to invalidate. This problem is reproducible by the following fio receipt (however I was only able to reproduce it with fio-2.1 or older. [global] bs=8k iodepth=1024 iodepth_batch=60 randrepeat=1 size=1m directory=/mnt/test numjobs=20 [job1] ioengine=sync bs=1k direct=1 rw=randread filename=file1:file2 [job2] ioengine=libaio rw=randwrite direct=1 filename=file1:file2 [job3] bs=1k ioengine=posixaio rw=randwrite direct=1 filename=file1:file2 [job5] bs=1k ioengine=sync rw=randread filename=file1:file2 [job7] ioengine=libaio rw=randwrite filename=file1:file2 [job8] ioengine=posixaio rw=randwrite filename=file1:file2 [job10] ioengine=mmap rw=randwrite bs=1k filename=file1:file2 [job11] ioengine=mmap rw=randwrite direct=1 filename=file1:file2 Signed-off-by:
Lukas Czerner <lczerner@redhat.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Darrick J. Wong authored
commit 292db1bc upstream. ext4 isn't willing to map clusters to a non-extent file. Don't signal this with an out of space error, since the FS will retry the allocation (which didn't fail) forever. Instead, return EUCLEAN so that the operation will fail immediately all the way back to userspace. (The fix is either to run e2fsck -E bmap2extent, or to chattr +e the file.) Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
-
Theodore Ts'o authored
commit 89d96a6f upstream. Normally all of the buffers will have been forced out to disk before we call invalidate_bdev(), but there will be some cases, where a file system operation was aborted due to an ext4_error(), where there may still be some dirty buffers in the buffer cache for the device. So try to force them out to memory before calling invalidate_bdev(). This fixes a warning triggered by generic/081: WARNING: CPU: 1 PID: 3473 at /usr/projects/linux/ext4/fs/block_dev.c:56 __blkdev_put+0xb5/0x16f() Signed-off-by:
-
Theodore Ts'o authored
commit bdf96838 upstream. The commit cf108bca: "ext4: Invert the locking order of page_lock and transaction start" caused __ext4_journalled_writepage() to drop the page lock before the page was written back, as part of changing the locking order to jbd2_journal_start -> page_lock. However, this introduced a potential race if there was a truncate racing with the data=journalled writeback mode. Fix this by grabbing the page lock after starting the journal handle, and then checking to see if page had gotten truncated out from under us. This fixes a number of different warnings or BUG_ON's when running xfstests generic/086 in data=journalled mode, including: jbd2_journal_dirty_metadata: vdc-8: bad jh for block 115643: transaction (ee3fe7 c0, 164), jh->b_transaction ( (null), 0), jh->b_next_transaction ( (null), 0), jlist 0 - and - kernel BUG at /usr/projects/linux/ext4/fs/jbd2/transaction.c:2200! ... Call Trace: [<c02b2ded>] ? __ext4_journalled_invalidatepage+0x117/0x117 [<c02b2de5>] __ext4_journalled_invalidatepage+0x10f/0x117 [<c02b2ded>] ? __ext4_journalled_invalidatepage+0x117/0x117 [<c027d883>] ? lock_buffer+0x36/0x36 [<c02b2dfa>] ext4_journalled_invalidatepage+0xd/0x22 [<c0229139>] do_invalidatepage+0x22/0x26 [<c0229198>] truncate_inode_page+0x5b/0x85 [<c022934b>] truncate_inode_pages_range+0x156/0x38c [<c0229592>] truncate_inode_pages+0x11/0x15 [<c022962d>] truncate_pagecache+0x55/0x71 [<c02b913b>] ext4_setattr+0x4a9/0x560 [<c01ca542>] ? current_kernel_time+0x10/0x44 [<c026c4d8>] notify_change+0x1c7/0x2be [<c0256a00>] do_truncate+0x65/0x85 [<c0226f31>] ? file_ra_state_init+0x12/0x29 - and - WARNING: CPU: 1 PID: 1331 at /usr/projects/linux/ext4/fs/jbd2/transaction.c:1396 irty_metadata+0x14a/0x1ae() ... Call Trace: [<c01b879f>] ? console_unlock+0x3a1/0x3ce [<c082cbb4>] dump_stack+0x48/0x60 [<c0178b65>] warn_slowpath_common+0x89/0xa0 [<c02ef2cf>] ? jbd2_journal_dirty_metadata+0x14a/0x1ae [<c0178bef>] warn_slowpath_null+0x14/0x18 [<c02ef2cf>] jbd2_journal_dirty_metadata+0x14a/0x1ae [<c02d8615>] __ext4_handle_dirty_metadata+0xd4/0x19d [<c02b2f44>] write_end_fn+0x40/0x53 [<c02b4a16>] ext4_walk_page_buffers+0x4e/0x6a [<c02b59e7>] ext4_writepage+0x354/0x3b8 [<c02b2f04>] ? mpage_release_unused_pages+0xd4/0xd4 [<c02b1b21>] ? wait_on_buffer+0x2c/0x2c [<c02b5a4b>] ? ext4_writepage+0x3b8/0x3b8 [<c02b5a5b>] __writepage+0x10/0x2e [<c0225956>] write_cache_pages+0x22d/0x32c [<c02b5a4b>] ? ext4_writepage+0x3b8/0x3b8 [<c02b6ee8>] ext4_writepages+0x102/0x607 [<c019adfe>] ? sched_clock_local+0x10/0x10e [<c01a8a7c>] ? __lock_is_held+0x2e/0x44 [<c01a8ad5>] ? lock_is_held+0x43/0x51 [<c0226dff>] do_writepages+0x1c/0x29 [<c0276bed>] __writeback_single_inode+0xc3/0x545 [<c0277c07>] writeback_sb_inodes+0x21f/0x36d ... Signed-off-by:
-
Haggai Eran authored
commit cab46214 upstream. With an RTL8191SU USB adaptor, sometimes the hints for a fragmented packet are set, but the packet length is too large. Allocate enough space to prevent memory corruption and a resulting kernel panic [1]. [1] http://www.spinics.net/lists/linux-wireless/msg136546.htmlSigned-off-by:
Haggai Eran <haggai.eran@gmail.com> ACKed-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Felix Fietkau authored
commit 300f77c0 upstream. AR93xx and newer needs to stop rx before tx to avoid getting the DMA engine or MAC into a stuck state. This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Marcel Holtmann authored
commit ecffc804 upstream. The SKB returned from the Intel specific version information command is missing a kfree_skb. Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
-
Boris BREZILLON authored
commit 60c3bc1f upstream. read_buf is called in place of write_buf in the nand_write_page_raw_syndrome function. Signed-off-by:
Boris BREZILLON <b.brezillon.dev@gmail.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Cc: Mason <slash.tmp@free.fr> Signed-off-by:
-
Brian Norris authored
commit bd9c6e99 upstream. Use a repeated read_byte() instead of read_buf(), since for x16 buswidth devices, we need to avoid the upper I/O[16:9] bits. See the following commit for reference: commit 05f78359 Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Date: Thu Dec 5 22:22:04 2013 +0100 mtd: nand: don't use {read,write}_buf for 8-bit transfers Now, I think that all barriers to probing ONFI on x16 devices are removed, so remove the check from nand_flash_detect_onfi(). Tested on 8-bit ONFI NAND (Micron MT29F32G08CBADAWP). Signed-off-by:
Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Tested-By:
Pekon Gupta <pekon@ti.com> Cc: Mason <slash.tmp@free.fr> Signed-off-by:
-
Thomas Petazzoni authored
commit ea78b951 upstream. There was a mistake in the definition of the functions for MPP48 on Marvell Armada XP. The second function is dev(clkout), and not tclk. Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Fixes: 463e270f ("pinctrl: mvebu: add pinctrl driver for Armada XP") Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Thomas Petazzoni authored
commit 80b3d04f upstream. The latest version of the Armada XP datasheet no longer documents the VDD cpu_pd functions, which might indicate they are not working and/or not supported. This commit ensures the pinctrl driver matches the datasheet. Signed-off-by:
-
Thomas Petazzoni authored
commit bc99357f upstream. After updating to a more recent version of the Armada XP datasheet, we realized that some of the pins documented as having a NAND-related functionality in fact did not have such functionality. This commit updates the pinctrl driver accordingly. Signed-off-by:
-
Thomas Petazzoni authored
commit 438881df upstream. Due to a mistake, the CS0 and CS1 SPI0 functions were incorrectly named "spi0-1" instead of just "spi0". This commit fixes that. This DT binding change does not affect any of the in-tree users. Signed-off-by:
-
Lukasz Majewski authored
commit 26bb0e9a upstream. It turns out that some boards can have instance->lower greater than 0 and when thermal trend is dropping it results with next_target equal to -1. Since the next_target is defined as unsigned long it is interpreted as 0xFFFFFFFF and larger than instance->upper. As a result the next_target is set to instance->upper which ramps up to maximal cooling device target when the temperature is steadily decreasing. Signed-off-by:
Lukasz Majewski <l.majewski@samsung.com> Signed-off-by:
Zhang Rui <rui.zhang@intel.com> Cc: Mason <slash.tmp@free.fr> Signed-off-by:
-
Uwe Kleine-König authored
commit e5babdf9 upstream. Since commit bd31b859 (which is in 3.2-rc1) nw_gpio_lock is a raw spinlock that needs usage of the corresponding raw functions. This fixes: drivers/mtd/maps/dc21285.c: In function 'nw_en_write': drivers/mtd/maps/dc21285.c:41:340: warning: passing argument 1 of 'spinlock_check' from incompatible pointer type spin_lock_irqsave(&nw_gpio_lock, flags); In file included from include/linux/seqlock.h:35:0, from include/linux/time.h:5, from include/linux/stat.h:18, from include/linux/module.h:10, from drivers/mtd/maps/dc21285.c:8: include/linux/spinlock.h:299:102: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *' static inline raw_spinlock_t *spinlock_check(spinlock_t *lock) ^ drivers/mtd/maps/dc21285.c:43:25: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type spin_unlock_irqrestore(&nw_gpio_lock, flags); ^ In file included from include/linux/seqlock.h:35:0, from include/linux/time.h:5, from include/linux/stat.h:18, from include/linux/module.h:10, from drivers/mtd/maps/dc21285.c:8: include/linux/spinlock.h:370:91: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *' static inline void spin_unlock_irqrestore(spinlock_t *lock, unsigned long flags) Fixes: bd31b859 ("locking, ARM: Annotate low level hw locks as raw") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Brian Norris authored
commit 073db4a5 upstream. On A MIPS 32-cores machine a BUG_ON was triggered because some acesses to mtd->usecount were done without taking mtd_table_mutex. kernel: Call Trace: kernel: [<ffffffff80401818>] __put_mtd_device+0x20/0x50 kernel: [<ffffffff804086f4>] blktrans_release+0x8c/0xd8 kernel: [<ffffffff802577e0>] __blkdev_put+0x1a8/0x200 kernel: [<ffffffff802579a4>] blkdev_close+0x1c/0x30 kernel: [<ffffffff8022006c>] __fput+0xac/0x250 kernel: [<ffffffff80171208>] task_work_run+0xd8/0x120 kernel: [<ffffffff8012c23c>] work_notifysig+0x10/0x18 kernel: kernel: Code: 2442ffff ac8202d8 000217fe <00020336> dc820128 10400003 00000000 0040f809 00000000 kernel: ---[ end trace 080fbb4579b47a73 ]--- Fixed by taking the mutex in blktrans_open and blktrans_release. Note that this locking is already suggested in include/linux/mtd/blktrans.h: struct mtd_blktrans_ops { ... /* Called with mtd_table_mutex held; no race with add/remove */ int (*open)(struct mtd_blktrans_dev *dev); void (*release)(struct mtd_blktrans_dev *dev); ... }; But we weren't following it. Originally reported by (and patched by) Zhang and Giuseppe, independently. Improved and rewritten. Reported-by:
Zhang Xingcai <zhangxingcai@huawei.com> Reported-by:
Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com> Tested-by:
Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by:
-
Grygorii Strashko authored
commit 084609bf upstream. Setting a dev_pm_ops suspend/resume pair of callbacks but not a set of hibernation callbacks means those pm functions will not be called upon hibernation - that leads to system crash on ARM during freezing if gpio-led is used in combination with CPU led trigger. It may happen after freeze_noirq stage (GPIO is suspended) and before syscore_suspend stage (CPU led trigger is suspended) - usually when disable_nonboot_cpus() is called. Log: PM: noirq freeze of devices complete after 1.425 msecs Disabling non-boot CPUs ... ^ system may crash or stuck here with message (TI AM572x) WARNING: CPU: 0 PID: 3100 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x22c/0x370() 44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in Supervisor mode during Functional access CPU1: shutdown ^ or here Fix this by using SIMPLE_DEV_PM_OPS, which appropriately assigns the suspend and hibernation callbacks and move led_suspend/led_resume under CONFIG_PM_SLEEP to avoid build warnings. Fixes: 73e1ab41 (leds: Convert led class driver from legacy pm ops to dev_pm_ops) Signed-off-by:
Grygorii Strashko <Grygorii.Strashko@linaro.org> Acked-by:
Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Axel Lin authored
commit 63781394 upstream. request_any_context_irq() returns a negative value on failure. It returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED on success. So fix testing return value of request_any_context_irq(). Also fixup the return value of devm_request_any_context_irq() to make it consistent with request_any_context_irq(). Fixes: 0668d306 ("genirq: Add devm_request_any_context_irq()") Signed-off-by:
Axel Lin <axel.lin@ingics.com> Reviewed-by:
Stephen Boyd <sboyd@codeaurora.org> Link: http://lkml.kernel.org/r/1431334978.17783.4.camel@ingics.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Bart Van Assche authored
commit 535fb906 upstream. Avoid that srp_terminate_io() can get invoked while srp_queuecommand() is in progress. This patch avoids that an I/O timeout can trigger the following kernel warning: WARNING: at drivers/infiniband/ulp/srp/ib_srp.c:1447 srp_terminate_io+0xef/0x100 [ib_srp]() Call Trace: [<ffffffff814c65a2>] dump_stack+0x4e/0x68 [<ffffffff81051f71>] warn_slowpath_common+0x81/0xa0 [<ffffffff8105204a>] warn_slowpath_null+0x1a/0x20 [<ffffffffa075f51f>] srp_terminate_io+0xef/0x100 [ib_srp] [<ffffffffa07495da>] __rport_fail_io_fast+0xba/0xc0 [scsi_transport_srp] [<ffffffffa0749a90>] rport_fast_io_fail_timedout+0xe0/0xf0 [scsi_transport_srp] [<ffffffff8106e09b>] process_one_work+0x1db/0x780 [<ffffffff8106e75b>] worker_thread+0x11b/0x450 [<ffffffff81073c64>] kthread+0xe4/0x100 [<ffffffff814cf26c>] ret_from_fork+0x7c/0xb0 See also patch "scsi_transport_srp: Add transport layer error handling" (commit ID 29c17324). Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Cc: James Bottomley <JBottomley@Odin.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Bart Van Assche authored
commit be34c62d upstream. Introduce the helper function srp_wait_for_queuecommand(). Move the definition of scsi_request_fn_active(). Add a comment above srp_wait_for_queuecommand() that support for scsi-mq needs to be added. This patch does not change any functionality. A second call to srp_wait_for_queuecommand() will be introduced in the next patch. Signed-off-by:
-
Ezequiel Garcia authored
commit ea6055c4 upstream. Since commit 39a6ac11 ("spi/pl022: Devicetree support w/o platform data") the 'num-cs' parameter cannot be passed through platform data when probing with devicetree. Instead, it's a required devicetree property. Fix the binding documentation so the property is properly specified. Fixes: 39a6ac11 ("spi/pl022: Devicetree support w/o platform data") Signed-off-by:
Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Martin Sperl authored
commit 8e76ef88 upstream. Fix a race (with some kernel configurations) where a queued master->pump_messages runs and frees dummy_tx/rx before spi_unmap_msg is running (or is finished). This results in the following messages: BUG: Bad page state in process page:db7ba030 count:0 mapcount:0 mapping: (null) index:0x0 flags: 0x200(arch_1) page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set ... Reported-by:
Noralf Trønnes <noralf@tronnes.org> Suggested-by:
Martin Sperl <kernel@martin.sperl.org> Signed-off-by:
-
Stefan Wahren authored
commit a7068e39 upstream. The buffer for condtraints debug isn't big enough to hold the output in all cases. So fix this issue by increasing the buffer. Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
-
Maxime Coquelin authored
commit 921cc294 upstream. The way the mask is generated in regmap_field_init() is wrong. Indeed, a field initialized with msb = 31 and lsb = 0 provokes a shift overflow while calculating the mask field. On some 32 bits architectures, such as x86, the generated mask is 0, instead of the expected 0xffffffff. This patch uses GENMASK() to fix the problem, as this macro is already safe regarding shift overflow. Signed-off-by:
Maxime Coquelin <maxime.coquelin@st.com> Signed-off-by:
-
Arun Chandran authored
commit 15b8d2c4 upstream. In big endian mode regmap_bulk_read gives incorrect data for byte reads. This is because memcpy of a single byte from an address after full word read gives different results when endianness differs. ie. we get little-end in LE and big-end in BE. Signed-off-by:
Arun Chandran <achandran@mvista.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit 3836785a upstream. If there is a PM QoS latency limit and all of the sufficiently shallow C-states are disabled, the cpuidle menu governor returns 0 which on some systems is CPUIDLE_DRIVER_STATE_START and shouldn't be returned if that C-state has been disabled. Fix the issue by modifying the menu governor to return (-1) in such situations. Signed-off-by:
Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com> Signed-off-by:
-
Will Deacon authored
commit 6f1a6ae8 upstream. When building the kernel with a bare-metal (ELF) toolchain, the -shared option may not be passed down to collect2, resulting in silent corruption of the vDSO image (in particular, the DYNAMIC section is omitted). The effect of this corruption is that the dynamic linker fails to find the vDSO symbols and libc is instead used for the syscalls that we intended to optimise (e.g. gettimeofday). Functionally, there is no issue as the sigreturn trampoline is still intact and located by the kernel. This patch fixes the problem by explicitly passing -shared to the linker when building the vDSO. Reported-by:
Szabolcs Nagy <Szabolcs.Nagy@arm.com> Reported-by:
James Greenlaigh <james.greenhalgh@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Dave P Martin authored
commit b9bcc919 upstream. The memmap freeing code in free_unused_memmap() computes the end of each memblock by adding the memblock size onto the base. However, if SPARSEMEM is enabled then the value (start) used for the base may already have been rounded downwards to work out which memmap entries to free after the previous memblock. This may cause memmap entries that are in use to get freed. In general, you're not likely to hit this problem unless there are at least 2 memblocks and one of them is not aligned to a sparsemem section boundary. Note that carve-outs can increase the number of memblocks by splitting the regions listed in the device tree. This problem doesn't occur with SPARSEMEM_VMEMMAP, because the vmemmap code deals with freeing the unused regions of the memmap instead of requiring the arch code to do it. This patch gets the memblock base out of the memblock directly when computing the block end address to ensure the correct value is used. Signed-off-by:
Dave Martin <Dave.Martin@arm.com> Signed-off-by:
-
Catalin Marinas authored
commit 565630d5 upstream. After secondary CPU boot or hotplug, the active_mm of the idle thread is &init_mm. The init_mm.pgd (swapper_pg_dir) is only meant for TTBR1_EL1 and must not be set in TTBR0_EL1. Since when active_mm == &init_mm the TTBR0_EL1 is already set to the reserved value, there is no need to perform any context reset. Signed-off-by:
-
Vineet Gupta authored
commit d57f7272 upstream. When auditing cmpxchg call sites, Chuck noted that gcc was optimizing away some of the desired LDs. | do { | new = old = *ipi_data_ptr; | new |= 1U << msg; | } while (cmpxchg(ipi_data_ptr, old, new) != old); was generating to below | 8015cef8: ld r2,[r4,0] <-- First LD | 8015cefc: bset r1,r2,r1 | | 8015cf00: llock r3,[r4] <-- atomic op | 8015cf04: brne r3,r2,8015cf10 | 8015cf08: scond r1,[r4] | 8015cf0c: bnz 8015cf00 | | 8015cf10: brne r3,r2,8015cf00 <-- Branch doesn't go to orig LD Although this was fixed by adding a ACCESS_ONCE in this call site, it seems safer (for now at least) to add compiler barrier to LLSC based cmpxchg Reported-by:
Chuck Jordan <cjordan@synopsys.com> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit b064a8fa upstream. Commit 73f7d1ca "ACPI / init: Run acpi_early_init() before timekeeping_init()" moved the ACPI subsystem initialization, including the ACPI mode enabling, to an earlier point in the initialization sequence, to allow the timekeeping subsystem use ACPI early. Unfortunately, that resulted in boot regressions on some systems and the early ACPI initialization was moved toward its original position in the kernel initialization code by commit c4e1acbb "ACPI / init: Invoke early ACPI initialization later". However, that turns out to be insufficient, as boot is still broken on the Tyan S8812 mainboard. To fix that issue, split the ACPI early initialization code into two pieces so the majority of it still located in acpi_early_init() and the part switching over the platform into the ACPI mode goes into a new function, acpi_subsystem_init(), executed at the original early ACPI initialization spot. That fixes the Tyan S8812 boot problem, but still allows ACPI tables to be loaded earlier which is useful to the EFI code in efi_enter_virtual_mode(). Link: https://bugzilla.kernel.org/show_bug.cgi?id=97141 Fixes: 73f7d1ca "ACPI / init: Run acpi_early_init() before timekeeping_init()" Reported-and-tested-by:
Marius Tolzmann <tolzmann@molgen.mpg.de> Signed-off-by:
Toshi Kani <toshi.kani@hp.com> Reviewed-by:
Hanjun Guo <hanjun.guo@linaro.org> Reviewed-by:
Lee, Chun-Yi <jlee@suse.com> Signed-off-by:
-
Takashi Iwai authored
commit 4df3fd17 upstream. Fujitsu Lifebook E780 sets the sequence number 0x0f to only only of the two headphones, thus the driver tries to assign another as the line-out, and this results in the inconsistent mapping between the created jack ctl and the actual I/O. Due to this, PulseAudio doesn't handle it properly and gets the silent output. The fix is to ignore the non-HP sequencer checks. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99681Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 7819717b upstream. Acer Aspire V5 with ALC282 codec needs the similar quirk like Dell laptops to support the headset mic. The headset mic pin is 0x19 and it's not exposed by BIOS, thus we need to fix the pincfg as well. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201Signed-off-by:
-
Ryan Underwood authored
commit 2fb22a80 upstream. Disable write buffering on the Toshiba ToPIC95 if it is enabled by somebody (it is not supposed to be a power-on default according to the datasheet). On the ToPIC95, practically no 32-bit Cardbus card will work under heavy load without locking up the whole system if this is left enabled. I tried about a dozen. It does not affect 16-bit cards. This is similar to the O2 bugs in early controller revisions it seems. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55961Signed-off-by:
Ryan C. Underwood <nemesis@icequake.net> Signed-off-by:
Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by:
-
Brian King authored
commit 45c44b5f upstream. Increase the default init stage change timeout from 15 seconds to 30 seconds. This resolves issues we have seen with some adapters not transitioning to the first init stage within 15 seconds, which results in adapter initialization failures. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Paul E. McKenney authored
commit 6e91f8cb upstream. If, at the time __rcu_process_callbacks() is invoked, there are callbacks in Tiny RCU's callback list, but none of them are ready to be invoked, the current list-management code will knit the non-ready callbacks out of the list. This can result in hangs and possibly worse. This commit therefore inserts a check for there being no callbacks that can be invoked immediately. This bug is unlikely to occur -- you have to get a new callback between the time rcu_sched_qs() or rcu_bh_qs() was called, but before we get to __rcu_process_callbacks(). It was detected by the addition of RCU-bh testing to rcutorture, which in turn was instigated by Iftekhar Ahmed's mutation testing. Although this bug was made much more likely by 915e8a4f (rcu: Remove fastpath from __rcu_process_callbacks()), this did not cause the bug, but rather made it much more probable. That said, it takes more than 40 hours of rcutorture testing, on average, for this bug to appear, so this fix cannot be considered an emergency. Signed-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by:
Josh Triplett <josh@joshtriplett.org> Signed-off-by:
-
- 10 Jul, 2015 2 commits
-
-
Greg Kroah-Hartman authored
-
David E. Box authored
commit aa8e4f22 upstream. Fixes an error in having the iosf build as 'default m'. On X86 SoC's the iosf sideband is the only way to access information for some registers, as opposed to through MSR's on other Intel architectures. While selecting IOSF_MBI is preferred, it does mean carrying extra code on non-SoC architectures. This exports the selection to the user, allowing those driver writers to compile out iosf code if it's not being built. Signed-off-by:
David E. Box <david.e.box@linux.intel.com> Link: http://lkml.kernel.org/r/1409175640-32426-2-git-send-email-david.e.box@linux.intel.comSigned-off-by:
H. Peter Anvin <hpa@linux.intel.com> Cc: William Dauchy <william@gandi.net> Signed-off-by:
-
