Change the default defconfig (used with 'make defconfig') to the ARCv2
nsim_hs_defconfig, and also switch the default Kconfig ISA selection to
ARCv2.

This allows several default defconfigs (e.g. make defconfig, make
allnoconfig, make tinyconfig) to all work with ARCv2 by default.

Note since we change default architecture from ARCompact to ARCv2
it's required to explicitly mention architecture type in ARCompact
defconfigs otherwise ARCv2 will be implied and binaries will be
generated for ARCv2.

Cc: <stable@vger.kernel.org> # 4.4.x
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

By default NFSv3 doesn't support ACL (Access Control Lists)
which might be quite convenient to have so that
mounted NFS behaves exactly as any other local file-system.

In particular missing support of ACL makes umask useless.
This among other thigs fixes Glibc's "nptl/tst-umask1".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Cupertino Miranda <cmiranda@synopsys.com>
Cc: stable@vger.kernel.org	#4.14+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Commit 15773ae9 ("signal/arc: Use force_sig_fault where
appropriate") introduced undefined behaviour by leaving si_code
unitiailized and leaking random kernel values to user space.

Fixes: 15773ae9 ("signal/arc: Use force_sig_fault where appropriate")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Enable GPIO support on HSDK. HSDK SoC includes Synopsys
DesignWare DW_apb_gpio IP with 24 GPIOs mapped onto port A.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

ARC gcc 8.x generates unaligned accesses by default, so call that out
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

If IOC was already enabled (due to bootloader) it technically needs to
be reconfigured with aperture base,size corresponding to Linux memory map
which will certainly be different than uboot's. But disabling and
reenabling IOC when DMA might be potentially active is tricky business.
To avoid random memory issues later, just panic here and ask user to
upgrade bootloader to one which doesn't enable IOC

This was actually seen as issue on some of the HSDK board with a version
of uboot which enabled IOC. There were random issues later with starting
of X or peripherals etc.

Also while I'm at it, replace hardcoded bits in ARC_REG_IO_COH_PARTIAL
and ARC_REG_IO_COH_ENABLE registers by definitions.

Inspired by: https://lkml.org/lkml/2018/1/19/557Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.

Also since commit f467c564 ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:

    ...
    One side effect of (and the main motivation for) this change is making
    the following two definitions behave exactly the same:

        config FOO
                bool

        config FOO
                bool
                default n

    With this change, neither of these will generate a
    '# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
    That might make it clearer to people that a bare 'default n' is
    redundant.
    ...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Pull networking fixes from David Miller:
 "One last pull request before heading to Vancouver for LPC, here we have:

   1) Don't forget to free VSI contexts during ice driver unload, from
      Victor Raj.

   2) Don't forget napi delete calls during device remove in ice driver,
      from Dave Ertman.

   3) Don't request VLAN tag insertion of ibmvnic device when SKB
      doesn't have VLAN tags at all.

   4) IPV4 frag handling code has to accomodate the situation where two
      threads try to insert the same fragment into the hash table at the
      same time. From Eric Dumazet.

   5) Relatedly, don't flow separate on protocol ports for fragmented
      frames, also from Eric Dumazet.

   6) Memory leaks in qed driver, from Denis Bolotin.

   7) Correct valid MTU range in smsc95xx driver, from Stefan Wahren.

   8) Validate cls_flower nested policies properly, from Jakub Kicinski.

   9) Clearing of stats counters in mc88e6xxx driver doesn't retain
      important bits in the G1_STATS_OP register causing the chip to
      hang. Fix from Andrew Lunn"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
  act_mirred: clear skb->tstamp on redirect
  net: dsa: mv88e6xxx: Fix clearing of stats counters
  tipc: fix link re-establish failure
  net: sched: cls_flower: validate nested enc_opts_policy to avoid warning
  net: mvneta: correct typo
  flow_dissector: do not dissect l4 ports for fragments
  net: qualcomm: rmnet: Fix incorrect assignment of real_dev
  net: aquantia: allow rx checksum offload configuration
  net: aquantia: invalid checksumm offload implementation
  net: aquantia: fixed enable unicast on 32 macvlan
  net: aquantia: fix potential IOMMU fault after driver unbind
  net: aquantia: synchronized flow control between mac/phy
  net: smsc95xx: Fix MTU range
  net: stmmac: Fix RX packet size > 8191
  qed: Fix potential memory corruption
  qed: Fix SPQ entries not returned to pool in error flows
  qed: Fix blocking/unlimited SPQ entries leak
  qed: Fix memory/entry leak in qed_init_sp_request()
  inet: frags: better deal with smp races
  net: hns3: bugfix for not checking return value
  ...

Merge tag 'kbuild-fixes-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - fix build errors in binrpm-pkg and bindeb-pkg targets

 - fix false positive matches in merge_config.sh

 - fix build version mismatch in deb-pkg target

 - fix dtbs_install handling in (bin)deb-pkg target

 - revert a commit that allows setlocalversion to write to source tree

* tag 'kbuild-fixes-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  builddeb: Fix inclusion of dtbs in debian package
  Revert "scripts/setlocalversion: git: Make -dirty check more robust"
  kbuild: deb-pkg: fix too low build version number
  kconfig: merge_config: avoid false positive matches from comment lines
  kbuild: deb-pkg: fix bindeb-pkg breakage when O= is used
  kbuild: rpm-pkg: fix binrpm-pkg breakage when O= is used

Pull btrfs fixes from David Sterba:
 "Several fixes to recent release (4.19, fixes tagged for stable) and
  other fixes"

* tag 'for-4.20-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: fix missing delayed iputs on unmount
  Btrfs: fix data corruption due to cloning of eof block
  Btrfs: fix infinite loop on inode eviction after deduplication of eof block
  Btrfs: fix deadlock on tree root leaf when finding free extent
  btrfs: avoid link error with CONFIG_NO_AUTO_INLINE
  btrfs: tree-checker: Fix misleading group system information
  Btrfs: fix missing data checksums after a ranged fsync (msync)
  btrfs: fix pinned underflow after transaction aborted
  Btrfs: fix cur_offset in the error case for nocow

Pull ext4 fixes from Ted Ts'o:
 "A large number of ext4 bug fixes, mostly buffer and memory leaks on
  error return cleanup paths"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: missing !bh check in ext4_xattr_inode_write()
  ext4: fix buffer leak in __ext4_read_dirblock() on error path
  ext4: fix buffer leak in ext4_expand_extra_isize_ea() on error path
  ext4: fix buffer leak in ext4_xattr_move_to_block() on error path
  ext4: release bs.bh before re-using in ext4_xattr_block_find()
  ext4: fix buffer leak in ext4_xattr_get_block() on error path
  ext4: fix possible leak of s_journal_flag_rwsem in error path
  ext4: fix possible leak of sbi->s_group_desc_leak in error path
  ext4: remove unneeded brelse call in ext4_xattr_inode_update_ref()
  ext4: avoid possible double brelse() in add_new_gdb() on error path
  ext4: avoid buffer leak in ext4_orphan_add() after prior errors
  ext4: avoid buffer leak on shutdown in ext4_mark_iloc_dirty()
  ext4: fix possible inode leak in the retry loop of ext4_resize_fs()
  ext4: fix missing cleanup if ext4_alloc_flex_bg_array() fails while resizing
  ext4: add missing brelse() update_backups()'s error path
  ext4: add missing brelse() add_new_gdb_meta_bg()'s error path
  ext4: add missing brelse() in set_flexbg_block_bitmap()'s error path
  ext4: avoid potential extra brelse in setup_new_flex_group_blocks()

Pull x86 fixes from Thomas Gleixner:
 "A set of x86 fixes:

   - Cure the LDT remapping to user space on 5 level paging which ended
     up in the KASLR space

   - Remove LDT mapping before freeing the LDT pages

   - Make NFIT MCE handling more robust

   - Unbreak the VSMP build by removing the dependency on paravirt ops

   - Support broken PIT emulation on Microsoft hyperV

   - Don't trace vmware_sched_clock() to avoid tracer recursion

   - Remove -pipe from KBUILD CFLAGS which breaks clang and is also
     slower on GCC

   - Trivial coding style and typo fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu/vmware: Do not trace vmware_sched_clock()
  x86/vsmp: Remove dependency on pv_irq_ops
  x86/ldt: Remove unused variable in map_ldt_struct()
  x86/ldt: Unmap PTEs for the slot before freeing LDT pages
  x86/mm: Move LDT remap out of KASLR region on 5-level paging
  acpi/nfit, x86/mce: Validate a MCE's address before using it
  acpi/nfit, x86/mce: Handle only uncorrectable machine checks
  x86/build: Remove -pipe from KBUILD_CFLAGS
  x86/hyper-v: Fix indentation in hv_do_fast_hypercall16()
  Documentation/x86: Fix typo in zero-page.txt
  x86/hyper-v: Enable PIT shutdown quirk
  clockevents/drivers/i8253: Add support for PIT shutdown quirk

Pull perf fixes from Thomas Gleixner:
 "A bunch of perf tooling fixes:

   - Make the Intel PT SQL viewer more robust

   - Make the Intel PT debug log more useful

   - Support weak groups in perf record so it's behaving the same way as
     perf stat

   - Display the LBR stats in callchain entries properly in perf top

   - Handle different PMu names with common prefix properlin in pert
     stat

   - Start syscall augmenting in perf trace. Preparation for
     architecture independent eBPF instrumentation of syscalls.

   - Fix build breakage in JVMTI perf lib

   - Fix arm64 tools build failure wrt smp_load_{acquire,release}"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools: Do not zero sample_id_all for group members
  perf tools: Fix undefined symbol scnprintf in libperf-jvmti.so
  perf beauty: Use SRCARCH, ARCH=x86_64 must map to "x86" to find the headers
  perf intel-pt: Add MTC and CYC timestamps to debug log
  perf intel-pt: Add more event information to debug log
  perf scripts python: exported-sql-viewer.py: Fix table find when table re-ordered
  perf scripts python: exported-sql-viewer.py: Add help window
  perf scripts python: exported-sql-viewer.py: Add Selected branches report
  perf scripts python: exported-sql-viewer.py: Fall back to /usr/local/lib/libxed.so
  perf top: Display the LBR stats in callchain entry
  perf stat: Handle different PMU names with common prefix
  perf record: Support weak groups
  perf evlist: Move perf_evsel__reset_weak_group into evlist
  perf augmented_syscalls: Start collecting pathnames in the BPF program
  perf trace: Fix setting of augmented payload when using eBPF + raw_syscalls
  perf trace: When augmenting raw_syscalls plug raw_syscalls:sys_exit too
  perf examples bpf: Start augmenting raw_syscalls:sys_{start,exit}
  tools headers barrier: Fix arm64 tools build failure wrt smp_load_{acquire,release}

Pull timer fix from Thomas Gleixner:
 "Just the removal of a redundant call into the sched deadline overrun
  check"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  posix-cpu-timers: Remove useless call to check_dl_overrun()

Pull scheduler fixes from Thomas Gleixner:
 "Two small scheduler fixes:

   - Take hotplug lock in sched_init_smp(). Technically not really
     required, but lockdep will complain other.

   - Trivial comment fix in sched/fair"

* 'sched/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix a comment in task_numa_fault()
  sched/core: Take the hotplug lock in sched_init_smp()

Pull locking build fix from Thomas Gleixner:
 "A single fix for a build fail with CONFIG_PROFILE_ALL_BRANCHES=y in
  the qspinlock code"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/qspinlock: Fix compile error

Pull core fixes from Thomas Gleixner:
 "A couple of fixlets for the core:

   - Kernel doc function documentation fixes

   - Missing prototypes for weak watchdog functions"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  resource/docs: Complete kernel-doc style function documentation
  watchdog/core: Add missing prototypes for weak functions
  resource/docs: Fix new kernel-doc warnings

If sch_fq is used at ingress, skbs that might have been
timestamped by net_timestamp_set() if a packet capture
is requesting timestamps could be delayed by arbitrary
amount of time, since sch_fq time base is MONOTONIC.

Fix this problem by moving code from sch_netem.c to act_mirred.c.

Fixes: fb420d5d ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fc ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a link failure is detected locally, the link is reset, the flag
link->in_session is set to false, and a RESET_MSG with the 'stopping'
bit set is sent to the peer.

The purpose of this bit is to inform the peer that this endpoint just
is going down, and that the peer should handle the reception of this
particular RESET message as a local failure. This forces the peer to
accept another RESET or ACTIVATE message from this endpoint before it
can re-establish the link. This again is necessary to ensure that
link session numbers are properly exchanged before the link comes up
again.

If a failure is detected locally at the same time at the peer endpoint
this will do the same, which is also a correct behavior.

However, when receiving such messages, the endpoints will not
distinguish between 'stopping' RESETs and ordinary ones when it comes
to updating session numbers. Both endpoints will copy the received
session number and set their 'in_session' flags to true at the
reception, while they are still expecting another RESET from the
peer before they can go ahead and re-establish. This is contradictory,
since, after applying the validation check referred to below, the
'in_session' flag will cause rejection of all such messages, and the
link will never come up again.

We now fix this by not only handling received RESET/STOPPING messages
as a local failure, but also by omitting to set a new session number
and the 'in_session' flag in such cases.

Fixes: 7ea817f4 ("tipc: check session number before accepting link protocol messages")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 37c8a5fa ("kbuild: consolidate Devicetree dtb build rules")
moved the location of 'dtbs_install' target which caused dtbs to not be
installed when building debian package with 'bindeb-pkg' target. Update
the builddeb script to use the same logic that determines if there's a
'dtbs_install' target which is presence of the arch dts directory. Also,
use CONFIG_OF_EARLY_FLATTREE instead of CONFIG_OF as that's a better
indication of whether we are building dtbs.

This commit will also have the side effect of installing dtbs on any
arch that has dts files. Previously, it was dependent on whether the
arch defined 'dtbs_install'.

Fixes: 37c8a5fa ("kbuild: consolidate Devicetree dtb build rules")
Reported-by: Nuno Gonçalves <nunojpg@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This reverts commit 6147b1cf.

The reverted patch results in attempted write access to the source
repository, even if that repository is mounted read-only.

Output from "strace git status -uno --porcelain":

getcwd("/tmp/linux-test", 129)          = 16
open("/tmp/linux-test/.git/index.lock", O_RDWR|O_CREAT|O_EXCL|O_CLOEXEC, 0666) =
	-1 EROFS (Read-only file system)

While git appears to be able to handle this situation, a monitored
build environment (such as the one used for Chrome OS kernel builds)
may detect it and bail out with an access violation error. On top of
that, the attempted write access suggests that git _will_ write to the
file even if a build output directory is specified. Users may have the
reasonable expectation that the source repository remains untouched in
that situation.

Fixes: 6147b1cf ("scripts/setlocalversion: git: Make -dirty check more robust"
Cc: Genki Sky <sky@genki.is>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Since commit b41d920a ("kbuild: deb-pkg: split generating packaging
and build"), the build version of the kernel contained in a deb package
is too low by 1.

Prior to the bad commit, the kernel was built first, then the number
in .version file was read out, and written into the debian control file.

Now, the debian control file is created before the kernel is actually
compiled, which is causing the version number mismatch.

Let the mkdebian script pass KBUILD_BUILD_VERSION=${revision} to require
the build system to use the specified version number.

Fixes: b41d920a ("kbuild: deb-pkg: split generating packaging and build")
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Doug Smythies <dsmythies@telus.net>

The current SED_CONFIG_EXP could match to comment lines in config
fragment files, especially when CONFIG_PREFIX_ is empty. For example,
Buildroot uses empty prefixing; starting symbols with BR2_ is just
convention.

Make the sed expression more robust against false positives from
comment lines. The new sed expression matches to only valid patterns.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>

Pull tty/serial fixes from Greg KH:
 "Here are some small tty fixes for 4.20-rc2

  One of these missed the original 4.19-final release, I missed that I
  hadn't done a pull request for it as it was in linux-next and my
  branch for a long time, that's my fault.

  The others are small, fixing some reported issues and finally fixing
  the termios mess for alpha so that glibc has a chance to implement
  some missing functionality that has been pending for many years now.

  All of these have been in linux-next with no reported issues"

* tag 'tty-4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: sh-sci: Fix could not remove dev_attr_rx_fifo_timeout
  arch/alpha, termios: implement BOTHER, IBSHIFT and termios2
  termios, tty/tty_baudrate.c: fix buffer overrun
  vt: fix broken display when running aptitude
  serial: sh-sci: Fix receive on SCIFA/SCIFB variants with DMA

Pull drm fixes from Dave Airlie:
 "drm: i915, amdgpu, sun4i, exynos and etnaviv fixes:

   - amdgpu has some display fixes, KFD ioctl fixes and a Vega20 bios
     interaction fix.

   - sun4i has some NULL checks added

   - i915 has a 32-bit system fix, LPE audio oops, and HDMI2.0 clock
     fixes.

   - Exynos has a 3 regression fixes (one frame counter, fbdev missing,
     dsi->panel check)

   - Etnaviv has a single fencing fix for GPU recovery"

* tag 'drm-fixes-2018-11-11' of git://anongit.freedesktop.org/drm/drm: (39 commits)
  drm/amd/amdgpu/dm: Fix dm_dp_create_fake_mst_encoder()
  drm/amd/display: Drop reusing drm connector for MST
  drm/amd/display: Cleanup MST non-atomic code workaround
  drm/amd/powerplay: always use fast UCLK switching when UCLK DPM enabled
  drm/amd/powerplay: set a default fclk/gfxclk ratio
  drm/amdgpu/display/dce11: only enable FBC when selected
  drm/amdgpu/display/dm: handle FBC dc feature parameter
  drm/amdgpu/display/dc: add FBC to dc_config
  drm/amdgpu: add DC feature mask module parameter
  drm/amdgpu/display: check if fbc is available in set_static_screen_control (v2)
  drm/amdgpu/vega20: add CLK base offset
  drm/amd/display: Stop leaking planes
  drm/amd/display: Fix misleading buffer information
  Revert "drm/amd/display: set backlight level limit to 1"
  drm/amd: Update atom_smu_info_v3_3 structure
  drm/i915: Fix ilk+ watermarks when disabling pipes
  drm/sun4i: tcon: prevent tcon->panel dereference if NULL
  drm/sun4i: tcon: fix check of tcon->panel null pointer
  drm/i915: Don't oops during modeset shutdown after lpe audio deinit
  drm/i915: Mark pin flags as u64
  ...

Pull namespace fixes from Eric Biederman:
 "I believe all of these are simple obviously correct bug fixes. These
  fall into two groups:

   - Fixing the implementation of MNT_LOCKED which prevents lesser
     privileged users from seeing unders mounts created by more
     privileged users.

   - Fixing the extended uid and group mapping in user namespaces.

  As well as ensuring the code looks correct I have spot tested these
  changes as well and in my testing the fixes are working"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  mount: Prevent MNT_DETACH from disconnecting locked mounts
  mount: Don't allow copying MNT_UNBINDABLE|MNT_LOCKED mounts
  mount: Retest MNT_LOCKED in do_umount
  userns: also map extents in the reverse map to kernel IDs

Pull clk fixes from Stephen Boyd:
 "A small set of fixes for clk drivers.

  One to fix a DT refcount imbalance, two to mark some Amlogic clks as
  critical, and one final one that fixes a clk name for the Qualcomm
  driver merged this cycle"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: qcom: gcc: Fix board clock node name
  clk: meson: axg: mark fdiv2 and fdiv3 as critical
  clk: meson-gxbb: set fclk_div3 as CLK_IS_CRITICAL
  clk: fixed-factor: fix of_node_get-put imbalance

Fixes for 4.20:
- DC MST fixes
- DC FBC fix
- Vega20 updates to support the latest vbios
- KFD type fixes for ioctl headers
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108035551.2904-1-alexander.deucher@amd.com

- sun4i: tcon->panel NULL deref protections (Giulio)

Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107205051.GA27823@art_vandelay

Merge tag 'drm-intel-fixes-2018-11-08' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

Bugzilla #108282 fixed: Avoid graphics corruption on 32-bit systems for Mesa 18.2.x
Avoid OOPS on LPE audio deinit. Remove two unused W/As.
Fix to correct HDMI 2.0 audio clock modes to spec.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108134508.GA28466@jlahtine-desk.ger.corp.intel.com

TCA_FLOWER_KEY_ENC_OPTS and TCA_FLOWER_KEY_ENC_OPTS_MASK can only
currently contain further nested attributes, which are parsed by
hand, so the policy is never actually used resulting in a W=1
build warning:

net/sched/cls_flower.c:492:1: warning: ‘enc_opts_policy’ defined but not used [-Wunused-const-variable=]
 enc_opts_policy[TCA_FLOWER_KEY_ENC_OPTS_MAX + 1] = {

Add the validation anyway to avoid potential bugs when other
attributes are added and to make the attribute structure slightly
more clear.  Validation will also set extact to point to bad
attribute on error.

Fixes: 0a6e7778 ("net/sched: allow flower to match tunnel options")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull xen fixes from Juergen Gross:
 "Several fixes, mostly for rather recent regressions when running under
  Xen"

* tag 'for-linus-4.20a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen: remove size limit of privcmd-buf mapping interface
  xen: fix xen_qlock_wait()
  x86/xen: fix pv boot
  xen-blkfront: fix kernel panic with negotiate_mq error path
  xen/grant-table: Fix incorrect gnttab_dma_free_pages() pr_debug message
  CONFIG_XEN_PV breaks xen_create_contiguous_region on ARM

Pull arm64 fixes from Catalin Marinas:

 - Fix occasional page fault during boot due to memblock resizing before
   the linear map is up.

 - Define NET_IP_ALIGN to 0 to improve the DMA performance on some
   platforms.

 - lib/raid6 test build fix.

 - .mailmap update for Punit Agrawal

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: memblock: don't permit memblock resizing until linear mapping is up
  arm64: mm: define NET_IP_ALIGN to 0
  lib/raid6: Fix arm64 test build
  mailmap: Update email for Punit Agrawal

Pull i2c updates from Wolfram Sang:
 "I2C has one bugfix (qcom-geni driver), one arch enablement (i2c-omap
  driver, no code change), and a new driver (nvidia-gpu) this time"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  usb: typec: ucsi: add support for Cypress CCGx
  i2c: nvidia-gpu: make pm_ops static
  i2c: add i2c bus driver for NVIDIA GPU
  i2c: qcom-geni: Fix runtime PM mismatch with child devices
  MAINTAINERS: Add entry for i2c-omap driver
  i2c: omap: Enable for ARCH_K3
  dt-bindings: i2c: omap: Add new compatible for AM654 SoCs

The reserved variable should be named reserved1.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only first fragment has the sport/dport information,
not the following ones.

If we want consistent hash for all fragments, we need to
ignore ports even for first fragment.

This bug is visible for IPv6 traffic, if incoming fragments
do not have a flow label, since skb_get_hash() will give
different results for first fragment and following ones.

It is also visible if any routing rule wants dissection
and sport or dport.

See commit 5e5d6fed ("ipv6: route: dissect flow
in input path if fib rules need it") for details.

[edumazet] rewrote the changelog completely.

Fixes: 06635a35 ("flow_dissect: use programable dissector in skb_flow_dissect and friends")
Signed-off-by: 배석진 <soukjin.bae@samsung.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A null dereference was observed when a sysctl was being set
from userspace and rmnet was stuck trying to complete some actions
in the NETDEV_REGISTER callback. This is because the real_dev is set
only after the device registration handler completes.

sysctl call stack -

<6> Unable to handle kernel NULL pointer dereference at
    virtual address 00000108
<2> pc : rmnet_vnd_get_iflink+0x1c/0x28
<2> lr : dev_get_iflink+0x2c/0x40
<2>  rmnet_vnd_get_iflink+0x1c/0x28
<2>  inet6_fill_ifinfo+0x15c/0x234
<2>  inet6_ifinfo_notify+0x68/0xd4
<2>  ndisc_ifinfo_sysctl_change+0x1b8/0x234
<2>  proc_sys_call_handler+0xac/0x100
<2>  proc_sys_write+0x3c/0x4c
<2>  __vfs_write+0x54/0x14c
<2>  vfs_write+0xcc/0x188
<2>  SyS_write+0x60/0xc0
<2>  el0_svc_naked+0x34/0x38

device register call stack -

<2>  notifier_call_chain+0x84/0xbc
<2>  raw_notifier_call_chain+0x38/0x48
<2>  call_netdevice_notifiers_info+0x40/0x70
<2>  call_netdevice_notifiers+0x38/0x60
<2>  register_netdevice+0x29c/0x3d8
<2>  rmnet_vnd_newlink+0x68/0xe8
<2>  rmnet_newlink+0xa0/0x160
<2>  rtnl_newlink+0x57c/0x6c8
<2>  rtnetlink_rcv_msg+0x1dc/0x328
<2>  netlink_rcv_skb+0xac/0x118
<2>  rtnetlink_rcv+0x24/0x30
<2>  netlink_unicast+0x158/0x1f0
<2>  netlink_sendmsg+0x32c/0x338
<2>  sock_sendmsg+0x44/0x60
<2>  SyS_sendto+0x150/0x1ac
<2>  el0_svc_naked+0x34/0x38

Fixes: b752eff5 ("net: qualcomm: rmnet: Implement ndo_get_iflink")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
net: aquantia: 2018-11 bugfixes

The patchset fixes a number of bugs found in various areas after
driver validation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>