This patch adds support for mt2701 chip to mtk_thermal,
and integrate both mt8173 and mt2701 on the same driver.
MT8173 has four banks and five sensors, and MT2701 has
only one bank and three sensors.
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

This adds the device tree binding documentation for the mediatek thermal
controller found on Mediatek MT2701.
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Maxim Semiconductor Max77620 supports alarm interrupts when
its die temperature crosses 120C and 140C. These threshold
temperatures are not configurable.

Add thermal driver to register PMIC die temperature as thermal
zone sensor and capture the die temperature warning interrupts
to notifying the client.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Maxim Semiconductor MAX77620 supports alarm interrupts when
its die temperature crosses 120C and 140C. These threshold
temperatures are not configurable.

Add DT binding document to details out the DT property related
to MAX77620 thermal functionality.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

When this platform is suspended, firmware powers the entire SoC down,
except a few hardware blocks waiting for wakeup events. There is no
context to save for this particular block.

Therefore, there is nothing useful for the driver to do on suspend;
so we define a NULL suspend hook. On resume, the driver initializes
the block exactly as is done in the probe callback.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

We could see that state is defined as unsigned type, so it
should never be less than zero. Let' remove this check.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

devm_thermal_zone_of_sensor_register() case doesn't need to call
thermal_zone_device_unregister().
Otherwise, rcar-thermal can't register thermal zone again after rebind.
This patch fixes it.
Signed-off-by: Bui Duc Phuc <bd-phuc@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Not much use unless the SoC is selected so depend on the ARCH_MXC
and COMPILE_TEST like all the other thermal drivers.

v2: drop extraneous OF
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

In case of error, the function of_iomap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
And the function devm_regmap_init_mmio() returns ERR_PTR()
and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

In less than 10 ms, the temperature of soc will arise 10 degree. 250 ms
is too big for soc tempeture control. Setting 2.5 ms will speed up
temperature accessing speed but introduce no more cpu's computing overhead.
We set AUTO_PERIOD_TIME and TSADCV3_AUTO_PERIOD_HT_TIME the same value,
because normal temperature update speed is also our consern in IPA.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Tested-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Due to the voltage ripple, the sensing data of the tsadc is not accurate.
And in this patch, the bandgap feature is enhanced to remove the voltage
ripple, and then the tsadc can sense the temperature more precisely.

Obsolete codes are removed as well.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Tested-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

The newly added tsens-8916 driver produces warnings when CONFIG_PM
is disabled:

drivers/thermal/qcom/tsens.c:53:12: error: 'tsens_resume' defined but not used [-Werror=unused-function]
 static int tsens_resume(struct device *dev)
            ^~~~~~~~~~~~
drivers/thermal/qcom/tsens.c:43:12: error: 'tsens_suspend' defined but not used [-Werror=unused-function]
 static int tsens_suspend(struct device *dev)
            ^~~~~~~~~~~~~

This marks both functions __maybe_unused to let the compiler
know that they might be used in other configurations, without
adding ugly #ifdef logic.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

This driver add thermal management support by enabling TMU (Thermal
Monitoring Unit) on QorIQ platform.

It's based on thermal of framework:
- Trip points defined in device tree.
- Cpufreq as cooling device registered in qoriq cpufreq driver.
Signed-off-by: Jia Hongtao <hongtao.jia@nxp.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

rcar-thermal is supporting both thermal_zone_of_sensor_register() and
thermal_zone_device_register(). But thermal_zone_of_sensor_register()
doesn't enable hwmon as default.
This patch enables it to keep compatibility
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Currently thermal zone set_emul_temp is set unconditionally
with of_thermal_set_emul_temp function. Set this only if the
set_emul_temp hook is provided for thermal_zone_of_device_ops.

This fixes emul_temp failures on platforms for which set_emul_temp
hook is not populated.

Fixes: "184a4bf6 (thermal: of: Extend current
	of-thermal.c code to allow setting emulated temp)"
Suggested-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Conflicts:
	drivers/thermal/of-thermal.c
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

The hardware-tracked trips will set the alarm interrupt value for
registers. Then when the thermal zone has no trips to be set,
That make the thermal trips callback a over range value.

The root cause is the rk_tsadcv2_temp_to_code() function to handle the
invalid temperature range is indeed incorrect, let's fix it on now.
Otherwise, the thermal alarm interrupt will be triggered all the time
on some SoCs.

Fox example:
localhost tmp # grep thermal /proc/interrupts; sleep 5;
grep thermal /proc/interrupts

23:     994830  ..    GICv3 129 Level     rockchip_thermal
23:    1003423  ..    GICv3 129 Level     rockchip_thermal
Reported-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

We should increase the period cycles to save power since the rk3399 has
the high frequency for tsadc clock.

Fixes commit b0d70338
("thermal: rockchip: Support the RK3399 SoCs in thermal driver")
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Whenever the current temperature is updated, the trip points immediately
below and above the current temperature are found. A sensor driver
callback `set_trips' is then called with the temperatures.
Lastly, The sensor will trigger the hardware high temperature interrupts
to increase the sampleing rate and throttle frequency to limit the
temperature rising When performing passive cooling.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Tested-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

With interrupt driven thermal zones we pass the lower and upper
temperature on which shall be acted, so in the governor we have to act on
the exact lower temperature to be consistent. Otherwise an interrupt maybe
generated on the exact lower temperature, but the bang bang governor does
not react since The polling driven zones have to be one step cooler before
the governor reacts.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Acked-by: Peter Feuerer <peter@piie.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

The .get_trend callback in struct thermal_zone_device_ops has
the prototype:
        int (*get_trend) (struct thermal_zone_device *, int,
                          enum thermal_trend *);
whereas the .get_trend callback in struct thermal_zone_of_device_ops
has:
        int (*get_trend)(void *, long *);

Streamline both prototypes and add the trip argument to the OF callback
aswell and use enum thermal_trend * instead of an integer pointer.

While the OF prototype may be the better one, this should be decided at
framework level and not on OF level.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

This patch implements .set_trips for device tree thermal zones.
As the hardware-tracked trip points is supported by thermal core patch[0].

patch[0]
"thermal: Add support for hardware-tracked trip points".
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

This adds support for hardware-tracked trip points to the device tree
thermal sensor framework.

The framework supports an arbitrary number of trip points. Whenever
the current temperature is updated, the trip points immediately
below and above the current temperature are found. A .set_trips
callback is then called with the temperatures. If there is no trip
point above or below the current temperature, the passed trip
temperature will be -INT_MAX or INT_MAX respectively. In this callback,
the driver should program the hardware such that it is notified
when either of these trip points are triggered. When a trip point
is triggered, the driver should call `thermal_zone_device_update'
for the respective thermal zone. This will cause the trip points
to be updated again.

If .set_trips is not implemented, the framework behaves as before.

This patch is based on an earlier version from Mikko Perttunen
<mikko.perttunen@kapsi.fi>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Trivial: remove the following:
drivers/thermal/qcom/tsens-8916.c:103:24: warning: symbol 'ops_8916' was not declared. Should it be static?
drivers/thermal/qcom/tsens-8996.c:76:24: warning: symbol 'ops_8996' was not declared. Should it be static?
drivers/thermal/qcom/tsens-8974.c:235:24: warning: symbol 'ops_8974' was not declared. Should it be static?
drivers/thermal/qcom/tsens-8960.c:279:24: warning: symbol 'ops_8960' was not declared. Should it be static?

Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

The TSENS controller in 8996 family of SoCs is capable of converting the
ADC code outputs to real temperature values (in decidegree Celsius).
It can also be programmed to provide raw ADC code, but the secure software
on 8996 programs it to provide real temperatures and also does the needed
calibrations.

We check the valid bit to ensure valid data is read by the AHB master.
And the spec recommends the below algorithm to read data 3 consecutive
times, which takes care of the worst case delay taken to propagate the
updated data to the register.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

8960 family of SoCs have the TSENS device as part of GCC, hence
the driver probes the virtual child device created by GCC and
uses the parent to extract all DT properties and reuses the GCC
regmap.

Also GCC/TSENS are part of a  domain thats not always ON.
Hence add .suspend and .resume hooks to save and restore some of
the inited register context.

Also 8960 family have some of the TSENS init sequence thats
required to be done by the HLOS driver (some later versions of TSENS
do not export these registers to non-secure world, and hence need
these initializations to be done by secure bootloaders)

8660 from the same family has just one sensor and hence some register
offset/layout differences which need special handling in the driver.

Based on the original code from Siddartha Mohanadoss, Stephen Boyd and
Narendran Rajan.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Add apis for platform thermal drivers to query for slope and offset
attributes, which might be needed for temperature calculations.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Add .calibrate support for 8974 family as part of tsens_ops.

Based on the original code by Siddartha Mohanadoss and Stephen Boyd.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Add support to calibrate sensors on 8916 family and also add common
functions to read temperature from sensors (This can be reused on
other SoCs having similar TSENS device)
The calibration data is read from eeprom using the generic nvmem
framework apis.

Based on the original code by Siddartha Mohanadoss and Stephen Boyd.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

TSENS is Qualcomms' thermal temperature sensor device. It
supports reading temperatures from multiple thermal sensors
present on various QCOM SoCs.
Calibration data is generally read from a non-volatile memory
(eeprom) device.

Add a skeleton driver with all the necessary abstractions so
a variety of qcom device families which support TSENS can
add driver extensions.

Also add the required device tree bindings which can be used
to describe the TSENS device in DT.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Pull x86 fix from Thomas Gleixner:
 "A single fix for an AMD erratum so machines without a BIOS fix work"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/AMD: Apply erratum 665 on machines without a BIOS fix

Pull timer fixes from Thomas Gleixner:
 "Two fixlet from the timers departement:

   - A fix for scheduler stalls in the tick idle code affecting
     NOHZ_FULL kernels

   - A trivial compile fix"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick/nohz: Fix softlockup on scheduler stalls in kvm guest
  clocksource/drivers/atmel-pit: Fix compilation error

Pull device mapper fixes from Mike Snitzer:

 - a stable fix in both DM crypt and DM log-writes for too large bios
   (as generated by bcache)

 - two other stable fixes for DM log-writes

 - a stable fix for a DM crypt bug that could result in freeing pointers
   from uninitialized memory in the tfm allocation error path

 - a DM bufio cleanup to discontinue using create_singlethread_workqueue()

* tag 'dm-4.8-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm bufio: remove use of deprecated create_singlethread_workqueue()
  dm crypt: fix free of bad values after tfm allocation failure
  dm crypt: fix error with too large bios
  dm log writes: fix check of kthread_run() return value
  dm log writes: fix bug with too large bios
  dm log writes: move IO accounting earlier to fix error path

Pull btrfs fixes from Chris Mason:
 "I'm still prepping a set of fixes for btrfs fsync, just nailing down a
  hard to trigger memory corruption.  For now, these are tested and ready."

* 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: fix one bug that process may endlessly wait for ticket in wait_reserve_ticket()
  Btrfs: fix endless loop in balancing block groups
  Btrfs: kill invalid ASSERT() in process_all_refs()

Pull arm64 fixes from Catalin Marinas:
 "arm64 and arm/perf fixes:

   - arm64 fix: debug exception unmasking on the CPU resume path

   - ARM PMU fixes: memory leak on error path and NULL pointer
     dereference"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: kernel: Fix unmasked debug exceptions when restoring mdscr_el1
  drivers/perf: arm_pmu: Fix NULL pointer dereference during probe
  drivers/perf: arm_pmu: Fix leak in error path

Pull char/misc driver fixes from Greg KH:
 "Here are a number of small driver fixes for 4.8-rc5.

  The largest thing here is deleting an obsolete driver,
  drivers/misc/bh1780gli.c, as the functionality of it was replaced by
  an iio driver a while ago.

  The other fixes are things that have been reported, or reverts of
  broken stuff (the binder change).  All of these changes have been in
  linux-next for a while with no reported issues"

* tag 'char-misc-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  thunderbolt: Don't declare Falcon Ridge unsupported
  thunderbolt: Add support for INTEL_FALCON_RIDGE_2C controller.
  thunderbolt: Fix resume quirk for Falcon Ridge 4C.
  lkdtm: Mark lkdtm_rodata_do_nothing() notrace
  mei: me: disable driver on SPT SPS firmware
  Revert "android: binder: fix dangling pointer comparison"
  drivers/iio/light/Kconfig: SENSORS_BH1780 cleanup
  android: binder: fix dangling pointer comparison
  misc: delete bh1780 driver

Pull driver core fixes from Greg KH:
 "Here are three small fixes for 4.8-rc5.

  One for sysfs, one for kernfs, and one documentation fix, all for
  reported issues.  All of these have been in linux-next for a while"

* tag 'driver-core-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  sysfs: correctly handle read offset on PREALLOC attrs
  documentation: drivers/core/of: fix name of of_node symlink
  kernfs: don't depend on d_find_any_alias() when generating notifications

Pull staging/IIO driver fixes from Greg KH:
 "Here are a number of small fixes for staging and IIO drivers that
  resolve reported problems.

  Full details are in the shortlog.  All of these have been in
  linux-next with no reported issues"

* tag 'staging-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (35 commits)
  arm: dts: rockchip: add reset node for the exist saradc SoCs
  arm64: dts: rockchip: add reset saradc node for rk3368 SoCs
  iio: adc: rockchip_saradc: reset saradc controller before programming it
  iio: accel: kxsd9: Fix raw read return
  iio: adc: ti_am335x_adc: Increase timeout value waiting for ADC sample
  iio: adc: ti_am335x_adc: Protect FIFO1 from concurrent access
  include/linux: fix excess fence.h kernel-doc notation
  staging: wilc1000: correctly check if associatedsta has not been found
  staging: wilc1000: NULL dereference on error
  staging: wilc1000: txq_event: Fix coding error
  MAINTAINERS: Add file patterns for ion device tree bindings
  MAINTAINERS: Update maintainer entry for wilc1000
  iio: chemical: atlas-ph-sensor: fix typo in val assignment
  iio: fix sched WARNING "do not call blocking ops when !TASK_RUNNING"
  staging: comedi: ni_mio_common: fix AO inttrig backwards compatibility
  staging: comedi: dt2811: fix a precedence bug
  staging: comedi: adv_pci1760: Do not return EINVAL for CMDF_ROUND_DOWN.
  staging: comedi: ni_mio_common: fix wrong insn_write handler
  staging: comedi: comedi_test: fix timer race conditions
  staging: comedi: daqboard2000: bug fix board type matching code
  ...

Pull serial driver fixes from Greg KH:
 "Here are some small serial driver fixes for 4.8-rc5.  One fixes an
  oft-reported build issue with the fintek driver, another reverts a
  patch that was causing problems, one fixes a crash, and some new
  device ids were added.

  All of these have been in linux-next for a while"

* tag 'tty-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: 8250: added acces i/o products quad and octal serial cards
  serial: 8250_mid: fix divide error bug if baud rate is 0
  Revert "tty/serial/8250: use mctrl_gpio helpers"
  8250/fintek: rename IRQ_MODE macro