The mxs-auart driver does not count FIFO overrun errors. These errors never
appear in /proc/tty/driver/ttyAPP. This is because the OERR status bit is
masked by read_status_mask in the rx interrupt function, but the
AUART_STAT_OERR bit is never set in read_status_mask. The patch enables the
counting of overrun errors.
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a set_ldisc function to enable/disable IrDA SIR mode according to
the new line discipline, if IrDA SIR mode is supported by the hardware
configuration.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Expose set_ldisc() function so that it can be overridden with a
platform specific implementation.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add an IrDA UART capability flag and change the type of
uart_8250_port.capabilities to be u32 rather than unsigned short to
accommodate the additional flag.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When any 8250 based driver sets up DMA and has UART_CAP_RPM capability enabled
the device is left powered on after transfer is done. We need to schedule a
device suspend operation when DMA completes the transfer.

The patch is based on the work done by the reporter.
Reported-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The following fix of runtime PM use in DMA mode requires at least
serial8250_rpm_put_tx() to be available. Export both calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When su_probe() fails it doesn't free *up and we may have a memory
leak. Fix this by freeing *up before return.
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In each call to hv_remove(), con_read_page and con_write_page is not
getting freed and lead to memory leakage. Fix this by freeing both
pointers in hv_remove().
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a disagreement between drivers/tty/vt/keyboard.c and
drivers/input/input-leds.c with regard to what is a Scroll Lock LED
trigger name: input calls it "kbd-scrolllock", but vt calls it
"kbd-scrollock" (two l's).
This prevents Scroll Lock LED trigger from binding to this LED by default.

Since it is a scroLL Lock LED, this interface was introduced only about a
year ago and in an Internet search people seem to reference this trigger
only to set it to this LED let's simply rename it to "kbd-scrolllock".

Also, it looks like this was supposed to be changed before this code was
merged: https://lkml.org/lkml/2015/6/9/697 but it was done only on
the input side.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: stable <stable@vger.kernel.org> # 4.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed typo in comments in drivers/tty/vt/keyboard.c
Signed-off-by: Askar Safin <safinaskar@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Declare an OF early console for SBSA UART so that the early console device
can be specified via the "stdout-path" property in device-tree.

Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use DEVICE_ATTR_RO for read only attributes.  This simplifies the
source code, improves readbility, and reduces the chance of
inconsistencies.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@ro@
declarer name DEVICE_ATTR;
identifier x,x_show;
@@

DEVICE_ATTR(x, \(0444\|S_IRUGO\), x_show, NULL);

@script:ocaml@
x << ro.x;
x_show << ro.x_show;
@@

if not (x^"_show" = x_show) then Coccilib.include_match false

@@
declarer name DEVICE_ATTR_RO;
identifier ro.x,ro.x_show;
@@

- DEVICE_ATTR(x, \(0444\|S_IRUGO\), x_show, NULL);
+ DEVICE_ATTR_RO(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The STM32 serial port is SoC specific so no point enabling it
without the architecture enabled.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When spi_setup() fails it doesn't free ifx_dev and we have a memory
leak. Fix this by freeing ifx_dev before the return.
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Inside ioc4_attach_local() 4 memory was allocated using kzalloc and
assign it to ports[] within loop. When kzalloc fails inside loop,
it returns error without freeing previously allocated memory and we
may have memory leak. Fix this by freeing ports[] before return.
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The fresh new serial driver for pxa produces warnings when
CONFIG_PM_SLEEP is disabled:

drivers/tty/serial/8250/8250_pxa.c:50:12: error: 'serial_pxa_resume' defined but not used [-Werror=unused-function]
drivers/tty/serial/8250/8250_pxa.c:41:12: error: 'serial_pxa_suspend' defined but not used [-Werror=unused-function]

This removes the #ifdef around the two functions and instead marks both
as __maybe_unused, which is more robust and avoids the warning.

Fixes: ab28f51c ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

An otherwise very nice cleanup of the pxa2xx uart support marked the
init function of this driver as __deprecated:

drivers/tty/serial/pxa.c:944:1: error: 'serial_pxa_init' is deprecated [-Werror=deprecated-declarations]

This seems unhelpful to me, as we now warn for every allmodconfig build,
which is otherwise free of warnings on most architectures. Let's
remove the annotation again.

Fixes: ab28f51c ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Drop invalid user-pointer check from TIOCGSERIAL handler.

A NULL-pointer can be valid in user space and copy_to_user() takes care
of sanity checking.

Cc: Mikael Starvik <starvik@axis.com>
Cc: linux-cris-kernel@axis.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Drop invalid user-pointer checks from custom ioctl handlers.

A NULL-pointer can be valid in user space and copy_to_user() takes care
of sanity checking.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Drop invalid user-pointer check from TIOCGSERIAL handler.

A NULL-pointer can be valid in user space and copy_to_user() takes care
of sanity checking.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Hi,
below patch to fix Fourth port offset of Percom PI7C9X7954 boards.

I had a problem using Fourth port on a pci express serial board based on Pericom
PI7C9X7954. Reading datasheet I notice a "special" offset assign to this port
when used in I/O mode.

Offset 0x0 ->  UART 0
Offset 0x8 ->  UART 1
Offset 0x10 ->  UART 2
Offset 0x38 ->  UART 3  <<---- This don't follow a logical sequence

This patch add a different init to last port, to have right offset.

I check also Pericom 7952 and 7958 but that devices follow logical sequence,
so they are ok.

Regards,
Angelo
Signed-off-by: Angelo Butti <buttiangelo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

While spin is already locked, serial output request causes the deadlock,
because serial output process also tries to lock the spin.
This patch removes serial output with spin locked.
Signed-off-by: Takatoshi Akiyama <takatoshi.akiyama.kj@ps.hitachi-solutions.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig currently controlling compilation of this code is:

arch/cris/arch-v10/drivers/Kconfig:config ETRAX_SERIAL
arch/cris/arch-v10/drivers/Kconfig:     bool "Serial-port support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We don't replace module.h with init.h since the file already has that.

Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-cris-kernel@axis.com
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The newly added pxa glue driver for 8250 supports console output, but
fails to build if the 8250 console is disabled:

drivers/tty/serial/8250/8250_pxa.o: In function `early_serial_pxa_setup':
8250_pxa.c:(.init.text+0x50): undefined reference to `early_serial8250_setup'

This adds an #ifdef like the other glue drivers have it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The hardware book says, the FCR is combined with a register called
CHAR (it will trigger interrupt when a specific character is
received).  At first, I used lock/read/modify/write/unlock dance for
the FCR to not affect the upper bits, but the CHAR is actually never
used.  It should not hurt to always clear the CHAR and to handle the
FCR as a normal case.  It can save the costly locking.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For this driver, uart_port::regshift is always 2.  Hardcode the
shift value instead of reading ->regshift to get an already known
value.  (pointed out by Denys Vlasenko)

Furthermore, I am using register macros that are already shifted,
which will save code a bit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the serial/tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull x86 bugfix from Thomas Gleixner:
 "A single bugfix for the recent changes related to registering the boot
  cpu when this has not happened before prefill_possible_map().

  The main problem with this change got fixed already, but we missed the
  case where the local APIC is not yet mapped, when prefill_possible_map()
  is invoked, so the registration of the boot cpu which has the APIC bit
  set in CPUID will explode.

  I should have seen that issue earlier, but all I can do now is feeling
  embarassed"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/smpboot: Init apic mapping before usage

Pull ubi/ubifs fixes from Richard Weinberger:
 "This contains fixes for issues in both UBI and UBIFS:

   - A regression wrt overlayfs, introduced in -rc2.
   - An UBI issue, found by Dan Carpenter's static checker"

* tag 'upstream-4.9-rc3' of git://git.infradead.org/linux-ubifs:
  ubifs: Fix regression in ubifs_readdir()
  ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()

Pull ARM SoC fixes from Olof Johansson:
 "We haven't seen a whole lot of fixes for the first two weeks since the
  merge window, but here is the batch that we have at the moment.

  Nothing sticks out as particularly bad or scary, it's mostly a handful
  of smaller fixes to several platforms. The Uniphier reset controller
  changes could probably have been delayed to 4.10, but they're not
  scary and just plumbing up driver changes that went in during the
  merge window.

  We're also adding another maintainer to Marvell Berlin platforms, to
  help out when Sebastian is too busy. Yay teamwork!"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
  ARM: dts: vf610: fix IRQ flag of global timer
  ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
  ARM: imx: gpc: Initialize all power domains
  arm64: dts: Updated NAND DT properties for NS2 SVK
  arm64: dts: uniphier: change MIO node to SD control node
  ARM: dts: uniphier: change MIO node to SD control node
  reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
  arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
  ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
  arm64: dts: Add timer erratum property for LS2080A and LS1043A
  arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
  ARM: multi_v7_defconfig: Enable Intel e1000e driver
  MAINTAINERS: add myself as Marvell berlin SoC maintainer
  bus: qcom-ebi2: depend on ARCH_QCOM or COMPILE_TEST
  ARM: dts: fix the SD card on the Snowball
  arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
  arm64: dts: marvell: fix clocksource for CP110 master SPI0
  ARM: mvebu: Select corediv clk for all mvebu v7 SoC

Pull char/misc driver fixes from Greg KH:
 "Here are a few small char/misc driver fixes for reported issues.

  The "biggest" are two binder fixes for reported issues that have been
  shipping in Android phones for a while now, the others are various
  fixes for reported problems.

  And there's a MAINTAINERS update for good measure.

  All have been in linux-next with no reported issues"

* tag 'char-misc-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  MAINTAINERS: Add entry for genwqe driver
  VMCI: Doorbell create and destroy fixes
  GenWQE: Fix bad page access during abort of resource allocation
  vme: vme_get_size potentially returning incorrect value on failure
  extcon: qcom-spmi-misc: Sync the extcon state on interrupt
  hv: do not lose pending heartbeat vmbus packets
  mei: txe: don't clean an unprocessed interrupt cause.
  ANDROID: binder: Clear binder and cookie when setting handle in flat binder struct
  ANDROID: binder: Add strong ref checks

Merge tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes

Correct regulator handling on Rockchip arm64 boards to make
bind/unbind calls work correctly and remove a sdio-only
property from non-sdio mmc hosts, that accidentially was
added there.

* tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
  arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux into fixes

This pull request contains a single fix for Broadcom ARM64-based SoCs:

- Ray adds the required bus width and OOB sector size properties to the
  Northstar 2 SVK reference board in order for the NAND controller to work
  properly

* tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux:
  arm64: dts: Updated NAND DT properties for NS2 SVK
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

The i.MX fixes for 4.9:
 - A couple of patches from Fabio to fix the GPC power domain regression
   which is caused by PM Domain core change 0159ec67
   ("PM / Domains: Verify the PM domain is present when adding a
   provider"), and a related kernel crash seen with multi_v7_defconfig
   build.
 - Correct the PHY ID mask for AR8031 to match phy driver code.
 - Apply new added timer erratum A008585 for LS1043A and LS2080A SoC.
 - Correct vf610 global timer IRQ flag to avoid warning from gic driver
   after commit 992345a5 ("irqchip/gic: WARN if setting the
   interrupt type for a PPI fails").

* tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
  ARM: dts: vf610: fix IRQ flag of global timer
  ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
  ARM: imx: gpc: Initialize all power domains
  arm64: dts: Add timer erratum property for LS2080A and LS1043A
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'uniphier-fixes-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into fixes

UniPhier ARM SoC fixes for v4.9

- Add "select ARCH_HAS_RESET_CONTROLLER" in Kconfig
- Rename wrongly-named mioctrl to sdctrl

* tag 'uniphier-fixes-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  arm64: dts: uniphier: change MIO node to SD control node
  ARM: dts: uniphier: change MIO node to SD control node
  reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
  arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
  ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull driver core fixes from Greg KH:
 "Here are two small driver core / kernfs fixes for 4.9-rc3.

  One makes the Kconfig entry for DEBUG_TEST_DRIVER_REMOVE a bit more
  explicit that this is a crazy thing to enable for a distro kernel
  (thanks for trying Fedora!), the other resolves an issue with vim
  opening kernfs files (sysfs, configfs, etc.)

  Both have been in linux-next with no reported issues"

* tag 'driver-core-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver core: Make Kconfig text for DEBUG_TEST_DRIVER_REMOVE stronger
  kernfs: Add noop_fsync to supported kernfs_file_fops

Pull staging and IIO driver fixes from Greg KH:
 "Here are some small staging and iio driver fixes for reported issues
  for 4.9-rc3. Nothing major, the "largest" being a lustre fix for a
  sysfs file that was obviously wrong, and had never been tested, so it
  was moved to debugfs as that is where it belongs. The others are small
  bug fixes for reported issues with various staging or iio drivers.

  All have been in linux-next for a while with no reported issues"

* tag 'staging-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  greybus: fix a leak on error in gb_module_create()
  greybus: es2: fix error return code in ap_probe()
  greybus: arche-platform: Add missing of_node_put() in arche_platform_change_state()
  staging: android: ion: Fix error handling in ion_query_heaps()
  iio: accel: sca3000_core: avoid potentially uninitialized variable
  iio:chemical:atlas-ph-sensor: Fix use of 32 bit int to hold 16 bit big endian value
  staging/lustre/llite: Move unstable_stats from sysfs to debugfs
  Staging: wilc1000: Fix kernel Oops on opening the device
  staging: android/ion: testing the wrong variable
  Staging: greybus: uart: Use gbphy_dev->dev instead of bundle->dev
  Staging: greybus: gpio: Use gbphy_dev->dev instead of bundle->dev
  iio: adc: ti-adc081c: Select IIO_TRIGGERED_BUFFER to prevent build errors
  iio: maxim_thermocouple: Align 16 bit big endian value of raw reads

Pull tty/serial driver fixes from Greg KH:
 "Here are a number of small tty and serial driver fixes for reported
  issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
  problems with the tty core changes that are in 4.9-rc1, and finally
  the atmel serial driver is back working properly.

  All have been in linux-next with no reported issues"

* tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial_core: fix NULL struct tty pointer access in uart_write_wakeup
  tty: serial_core: Fix serial console crash on port shutdown
  tty/serial: at91: fix hardware handshake on Atmel platforms
  vt: clear selection before resizing
  sc16is7xx: always write state when configuring GPIO as an output
  sh-sci: document R8A7743/5 support
  tty: serial: 8250: 8250_core: NXP SC16C2552 workaround
  tty: limit terminal size to 4M chars
  tty: serial: fsl_lpuart: Fix Tx DMA edge case
  serial: 8250_lpss: enable MSI for sure
  serial: core: fix console problems on uart_close
  serial: 8250_uniphier: fix clearing divisor latch access bit
  serial: 8250_uniphier: fix more unterminated string
  serial: pch_uart: add terminate entry for dmi_system_id tables
  devicetree: bindings: uart: Add new compatible string for ZynqMP
  serial: xuartps: Add new compatible string for ZynqMP
  serial: SERIAL_STM32 should depend on HAS_DMA
  serial: stm32: Fix comparisons with undefined register
  tty: vt, fix bogus division in csi_J

Pull USB fixes from Greg KH:
 "Here are a number of small USB driver fixes for 4.9-rc3.

  There is the usual number of gadget and xhci patches in here to
  resolved reported issues, as well as some usb-serial driver fixes and
  new device ids.

  All have been in linux-next with no reported issues"

* tag 'usb-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
  usb: chipidea: host: fix NULL ptr dereference during shutdown
  usb: renesas_usbhs: add wait after initialization for R-Car Gen3
  usb: increase ohci watchdog delay to 275 msec
  usb: musb: Call pm_runtime from musb_gadget_queue
  usb: musb: Fix hardirq-safe hardirq-unsafe lock order error
  usb: ehci-platform: increase EHCI_MAX_RSTS to 4
  usb: ohci-at91: Set RemoteWakeupConnected bit explicitly.
  USB: serial: fix potential NULL-dereference at probe
  xhci: use default USB_RESUME_TIMEOUT when resuming ports.
  xhci: workaround for hosts missing CAS bit
  xhci: add restart quirk for Intel Wildcatpoint PCH
  USB: serial: cp210x: fix tiocmget error handling
  wusb: fix error return code in wusb_prf()
  Revert "Documentation: devicetree: dwc2: Deprecate g-tx-fifo-size"
  Revert "usb: dwc2: gadget: fix TX FIFO size and address initialization"
  Revert "usb: dwc2: gadget: change variable name to more meaningful"
  USB: serial: ftdi_sio: add support for Infineon TriBoard TC2X7
  wusb: Stop using the stack for sg crypto scratch space
  usb: dwc3: Fix size used in dma_free_coherent()
  usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable
  ...