Remove unneeded, undesirable cast of void*.

Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

There is another outstanding issue with ata_piix.c.  Intel has never
officially supported anything faster than PATA 100MB/s.

But, the ata_piix.c driver "define" the ICH5 & ICH7 as UDMA6 (aka 133MB/s)
capable.  [ Well, no one has probably noticed it before, because there is bug
in do_pata_set_dmamode...  Just look at
libata_atapiix_enable_real_udma133.patch and you'll see what wrong with it.  ]

Here are Intel's datasheets for the affected chipsets: ICH5 Datasheet:
http://www.intel.com/design/chipsets/datashts/252516.htm (See note on page
183: "...  the ICH5 supports reads at the maximum rate of 100MB/s.")

ICH7 Datasheet: http://www.intel.com/design/chipsets/datashts/307013.htm (See
first note on page 190: "...  the ICH7 supports reads at the maximum rate of
100MB/s.")

They are two different ways to deal with it:

- Either -

1. replace all ich_pata_133 with ich_pata_100.
   (libata_atapiix_disable_udma6.diff - diff from 2.6.22 )

- Or -

2. keep all ich_pata_133 and fix the bug in "do_pata_set_dmamode".
   (libata_atapiix_enable_real_udma133.patch - diff from 2.6.22) If there are
   any concerns about the safety of the patch patch:
   http://lkml.org/lkml/2007/7/6/292 (It was already tested by an Intel
   employee, but I guess a bit more user input is necessary here...  )

This patch implements 1.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Use a stored value for which interrupts to enable.  Changing this allows
us to selectively turn off certain interrupts later and have them
stay off.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

When we get an SDB FIS with the 'N' bit set, we should send
an event to user space to indicate that there has been a
media change.  This will be done via the scsi device.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Check to see if an ATAPI device supports Asynchronous Notification.
If so, enable it, if the host controller supports AN.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Set the MWDMA timing by updating the correct registers.  Split the PIO path as
this is mostly shared code.  Wants testing.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Remembered this while doing auditing and code review versus the specs
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add support for issuing ATA_16 passthru commands to ATAPI devices
managed by libata.  It requires the previous CDB length fix patch.

A boot/module parameter, "atapi_passthru16=0" can be used to globally
disable this feature, if ever desired.

tj: restructured __ata_scsi_queuecmd() according to Jeff's suggestion.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Move ata_altstatus() out from ata_hsm_move() to the pio data xfer
functions like ata_pio_sectors() and atapi_pio_bytes() where it makes
more sense.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Debugging a report of a problem with an ancient solid state disk showed
up some problems in the IORDY handling

1.	We check the wrong bit to see if the device has IORDY
2.	Even then some ancient creaking piles of crap don't support
	SETXFER at all.

The cases it fixes are obscure and the risk of side effects is slight
but possible. This also moves us slightly closer to supporting original
MFM/RLL disks with libata.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Update Power Management to consider PMP links.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Update hotplug to handle PMP links.  When PMP is attached, the PMP
number corresponds to C of SCSI H:C:I:L.  While at it, change argument
to ata_find_dev() to @devno from @id to avoid confusion with SCSI
device ID.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Update ata_eh_autopsy(), ata_eh_report(),
ata_eh_revalidate_and_attach() and ata_eh_recover() to deal with PMP
links.  ata_eh_autopsy() and ata_eh_report() updates are
straightforward.  They just repeat the same operation over all
configured links.  The only change to ata_eh_revalidate_and_attach()
is avoiding calling ->cable_select() on non-host ports.

ata_eh_recover() update is more complex as it first processes all
resets and then performs the rest.  This is necessary as thawing with
some links in unknown state can be dangerous.  ehi->action is cleared
on successful recovery of a link to avoid repeating recovery due to
failures in other links.

ata_eh_recover() iterates over only PMP links if PMP is attached, and,
on failure, the failing link is returned in @failed_link instead of
disabling devices directly.  These are to integrate ata_eh_recover()
into PMP EH later.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Update ata_scsi_error() to handle PMP links.  As error conditions can
occur on both host and PMP links, __ata_port_for_each_link() is used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add link->pmp, ap->nr_pmp_links, ap->pmp_link[], and implement/update
link helpers.

printk helpers are updated such that port and link are identifed as
'ataP:' if no PMP is attached, while device is identified as
'ataP.DD:'.  If PMP is attached, they become 'ataP:', 'ataP.LL:' and
'ataP.LL' - ie. link and device are identified their PMP number.

If PPM is attached (ap->nr_pmp_links != 0), ata_for_each_link()
iterates over PMP links, while __ata_for_each_link() iterates over the
host link + PMP links.  If PMP is not attached (ap->nr_pmp_links ==
0), both iterate over only the host link.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Implement ata_link_abort().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Separate out link initialization into ata_link_init() and
ata_link_init_sata_spd().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

HRST_TO_RESUME and SKIP_D2H_BSY are link attributes.  Move them to
ata_link->flags.  This will allow host and PMP links to have different
attributes.  ata_port_info->link_flags is added and used by LLDs to
specify these flags during initialization.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Make the following functions deal with ata_link instead of ata_port.

* ata_set_mode()
* ata_eh_autopsy() and related functions
* ata_eh_report() and related functions
* suspend/resume related functions
* ata_eh_recover() and related functions
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Make reset methods and related functions deal with ata_link instead of
ata_port.

* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions

This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Make ata_eh_about_to_do() and ata_eh_done() deal with ata_link instead
of ata_port.

This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Make the following PHY-related functions to deal with ata_link instead
of ata_port.

* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()

This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Multiple links and different number of devices per link should be
considered to iterate over links and devices.  This patch implements
and uses link and device iterators - ata_port_for_each_link() and
ata_link_for_each_dev() - and ata_link_max_devices().

This change makes a lot of functions iterate over only possible
devices instead of from dev 0 to dev ATA_MAX_DEVICES.  All such
changes have been examined and nothing should be broken.

While at it, add a separating comment before device helpers to
distinguish them better from link helpers and others.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Introduce ata_link.  It abstracts PHY and sits between ata_port and
ata_device.  This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port.  Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.

This patch only defines the host link.  Multiple link handling will be
added later.  Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.

This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [ZLIB]: Fix external builds of zlib_inflate code.
  [TG3]: Fix APE induced regression
  [SKY2]: version 1.19
  [SKY2]: use netdevice stats struct
  [SKY2]: fiber advertise bits initialization (trivial)
  [SKY2]: fix power settings on Yukon XL
  [SKY2]: ethtool register reserved area blackout

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Move zlib_inflate_blob() out into it's own source file,
infutil.c, so that things like the powerpc zImage builder
in arch/powerpc/boot/Makefile don't end up trying to
compile it.
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a bug caused by the recent APE support added for 5761
devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update version to keep track of new changes.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use builtin statistics structure from net device.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Put initialization in sequential order (same as other constants).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure PCI register for PHY power gets set correctly.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure and not dump reserved areas of device space.
Touching some of these causes machine check exceptions on boards
like D-Link DGE-550SX.

Coding note, used a complex switch statement rather than bitmap
because it is easier to relate the block values to the documentation
rather than looking at a encoded bitmask.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
  [POWERPC] Add memchr() to the bootwrapper
  [POWERPC] Implement logging of unhandled signals
  [POWERPC] Add legacy serial support for OPB with flattened device tree
  [POWERPC] Use 1TB segments
  [POWERPC] XilinxFB: Allow fixed framebuffer base address
  [POWERPC] XilinxFB: Add support for custom screen resolution
  [POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
  [POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
  [POWERPC] 4xx: Kilauea defconfig file
  [POWERPC] 4xx: Kilauea DTS
  [POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
  [POWERPC] 4xx: Add AMCC 405EX support to cputable.c
  [POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
  [POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
  [POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
  [POWERPC] 85xx: Killed <asm/mpc85xx.h>
  [POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
  [POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
  [POWERPC] mpc8272ads: Remove muram from the CPM reg property.
  [POWERPC] Make clockevents work on PPC601 processors
  ...

Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.

* 'upstream-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] sata_mv: more S/G fixes

* corruption fix: we only want the lower 16 bits of length (0 == 64kb)

* ditto: the upper layer sets max-phys-segments to LIBATA_MAX_PRD,
  so we must reset it to own hw-specific length.

* delete unused mv_fill_sg() return value
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>