- 05 Mar, 2009 40 commits
-
-
Jouni Malinen authored
Allow RX filter to pass through all broadcast/multicast frames (i.e., no BSSID filtering) if virtual interfaces are used. Software filtering will be used in this case to drop broadcast/multicast frames for foreign BSSIDs. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
The new struct ath_softc::sec_wiphy array is used to store information about virtual wiphys and select which wiphy is used in calls to mac80211. Each virtual wiphy will be assigned a different MAC address based on the virtual wiphy index. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
This is the initial step in allowing ath9k to register multiple virtual radios (wiphys). The goal of virtual radios is to allow the same radio to be shared for multiple virtual interfaces that may operate on different channels. The mac80211 virtual interface support is designed only for single channel operation and as such, it is not suitable for this type of use. Anyway, it can be used on top of the virtual radio concept, if desired (e.g., use two virtual radios to handle two channels and then add multiple mac80211 virtual interfaces on top of each virtual radio). The new struct ath_wiphy is now registered as the driver data structure for wiphy. This structure has a pointer to the shared (among virtual wiphys of the same physical radio) struct ath_softc data. The primary wiphy maintains the allocated memory for ath_softc. Secondary (virtual) wiphys will only allocate the new ath_wiphy structure. Registration of secondary wiphys is added in a separate patch. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
Instead of using a hardcoded BSSID mask (mask for own addresses), iterate through all active interfaces and determine the minimal mask that covers all local addresses. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
Replace the internal sc_vaps array and index values by using vif pointer from mac80211. Allow multiple VIPs to be registered. Though, number of beaconing VIFs is still limited by ATH_BCBUF (currently 1). Multiple virtual STAs support is not yet complete, but at least the data structures should now be able to handle this. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ivo van Doorn authored
By exporting the register base, and word size to userspace through debugfs it will be easier to create scripts which parse the register information. This makes debugging and register dumps information easier. This will break my previous scripts which dumped and parsed all information, but since this is only for debugging purposes this change should not be a problem. Dumpfiles created with the old version can be easily manually edited to make them compatible with this new approach, which means there will be no problems comparing dumps from the different versions either. Also be more consistent with using tabs to seperate different fields. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
There is no need to use ath_keyset() wrapper for ath9k_hw_set_keycache_entry() calls. In addition, improve the comments describing the key setting operations. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
The current bitmask is invalid, because the tx dma size is a 3 bit wide value. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
We don't store the beacon timestamp internally, nor do we do any TIM handling in ath9k. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
The TSF has to be reset only once, upon bringing the interface up in AP mode. For any beacon reconfigure calls after that, resetting the TSF results in incorrect beacon generation. The only exception is a change in the beacon interval, which is indicated to the driver by mac80211 through IEEE80211_CONF_CHANGE_BEACON_INTERVAL, handle this properly. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
This makes the code easier to understand. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
We never use SC_OP_NO_RESET, it is not configurable at all. Remove all code that deals with this flag and make beacon stuck processing simple. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
Remove useless comments, fix indentation. Also, remove all occurrences of ASSERT(vif) which are not needed. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
The only use case for this right now is ANI calibration, but more might come up in the future. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
In IBSS mode, the beacon timestamp has to be filled with the BSS's timestamp when joining, and set to zero when creating a new BSS. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Alina Friedrichsen authored
The old code doesn't work correctly e.g. on newer chipsets like AR5418+AR2122 and AR5416+AR2133. Signed-off-by: Alina Friedrichsen <x-alina@gmx.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Alina Friedrichsen authored
The old code doesn't work correctly e.g. on newer chipsets like AR5418+AR2122 and AR5416+AR2133. Signed-off-by: Alina Friedrichsen <x-alina@gmx.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Michael Buesch authored
This changes the RX handler to pass more status flags to mac80211. It also changes part of the drop policy, if bad frames were requested. (Note that currently mac80211 will throw a WARN_ON in that case. But nothing bad will happen). This also removes some obsolete unused timestamping code. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Alina Friedrichsen authored
So that a new created IBSS network doesn't break on the first scan. It seems to Sujith and me that this stupid code unnecessary, too. So remove it... Signed-off-by: Alina Friedrichsen <x-alina@gmx.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vivek Natarajan authored
Restore network sleep mode in isr if power save is enabled. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
This callback can be used to handle dynamic 20/40, and changes in the operating channel's HT parameters. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vivek Natarajan authored
If the AP thinks we are in power save state eventhough we are not truly in that state, it sets the TIM bit and does not send a data frame unless we send a null data frame to correct the state in the AP. This might happen if the null data frame for wake up is lost in the air after we disable power save. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
This is not used anywhere in ath9k and is just making the code more confusing. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
There are number of small details about the keycache operations that are very easy to miss (and forget), so better include detailed comments in ath9k_hw_set_keycache_entry() to avoid having to figure out this every time when having to touch this area. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
There is no need to parse the AP's HT capabilities if the STA uses TKIP/WEP cipher. This allows the rate control module to choose the correct(legacy) rate table. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Frank Seidel authored
Reduce stack memory footprint of iwlwifi. (From >1000 bytes for each *_table_read on i386 down to 32) Signed-off-by: Frank Seidel <frank@f-seidel.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ivo van Doorn authored
Software antenna tuning is broken because of an function ordering problem during rt2x00link_tuner(). rt2x00link_precalculate_signal() rt2x00leds_led_quality() rt2x00lib_antenna_diversity() rt2x00link_precalculate_signal() will reset the quality TX/RX counters, however rt2x00lib_antenna_diversity() requires the RX counter to see what RSSI value must be used for a particular antenna. We can't change the ordering since rt2x00lib_antenna_diversity() might reset other statistics which are needed by the function called earlier. Move the reset of the quality TX/RX counters into a seperate function and move the call to after rt2x00lib_antenna_diversity(). Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Abhijeet Kolekar authored
3945 can use iwl_activate_qos instead of iwl3945_activate_qos. Patch does two things 1) Patch adds iwl_activate_qos in core library. 2) 3945 makes use of iwl_activate_qos. Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Abhijeet Kolekar authored
Patch does following, 1) mac80211's shared data is now initialized in iwl3945_setup_mac. 2) Set the rfkill to right state after initialization Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Reinette Chatre authored
for iwlagn: - Have to free eeprom of version check fails - otherwise we end up with memory leak. - Include removal of workqueue (created in _setup_deferred_work) in error handling. for iwl3945: - Fix a few places to jump to correct error handling. - Reorganize error handling to match with code flow. - Include iwl_free_channel_map as part of error handling. - Include releasing eeprom as part of error handling. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Abhijeet Kolekar authored
unify the set key flow with iwlwifi. Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Acked-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Abhijeet Kolekar authored
In IBSS, TSF maintains local clock counters at each station. Network Synchronization follows a completely distributed scheme where beacon frames are generated. Each station maintain its own TSF timestamp, extracted from beacon timestamps they recieved. Following patch synchronize this beacon timestamp with uCode. Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jay Sternberg authored
update API to support new numbering that is used for other newer devices. 5150 ucode has not been released yet, so the first released API will be v2. For those who do have a v1 API the driver does have backward compatibility support new value of REPLY_TX_POWER_DBM_CMD Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Since "mac80211/cfg80211: move iwrange handler to cfg80211", the results for link quality from "iwlist scan" and "iwconfig" commands have been very different. The results are now consistent. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Reported- and tested-by: Larry Finger <larry.finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Michael Buesch authored
This adds SSB functionality to register a fallback SPROM image from the architecture setup code. Weird architectures exist that have half-assed SSB devices without SPROM attached to their PCI busses. The architecture can register a fallback SPROM image that is used if no SPROM is found on the SSB device. Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: Florian Fainelli <florian@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
Currently, the driver is unconditionally notified of beacon interval. This is a problem in AP mode, because the driver has to know that the beacon interval has actualy changed to recalculate TBTT and reset the HW TSF. Fix this to make mac80211 notify the driver only when the beacon interval has been reconfigured to a new value. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jiri Slaby authored
Make sure we print out a warning when the index is out of bounds, i.e. even on hw_rix == AR5K_MAX_RATES. Also change to WARN and print text with the reported hw_rix. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Nick Kossifidis <mickflemm@gmail.com> Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Cc: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
Incorrect Michael MIC key (RX, should have been TX) was set for the group key in AP mode. This resulted in all broadcast frames triggering Michael MIC errors and eventual TKIP countermeasures. The change here sets the correct Michael MIC key based on whether the local end is the authenticator (well, AP for now). Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Tested-by: Pat Erley <pat-lkml@erley.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Frank Seidel authored
Applying kernel janitors todos (reduce stack footprint where possible) to airo wireless driver. (Before 1124 bytes on i386, now 876) Signed-off-by: Frank Seidel <frank@f-seidel.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-