As the comment of pci_get_domain_bus_and_slot() says, it
returns a PCI device with refcount incremented, when finish
using it, the caller must decrement the reference count by
calling pci_dev_put().

In ixgbe_get_first_secondary_devfn() and ixgbe_x550em_a_has_mii(),
pci_dev_put() is called to avoid leak.

Fixes: 8fa10ef0 ("ixgbe: register a mdiobus")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

resources allocated like mcam entries to support the Ntuple feature
and hash tables for the tc feature are not getting freed in driver
unbind. This patch fixes the issue.

Fixes: 2da48943 ("octeontx2-pf: devlink params support to set mcam entry count")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20230109061325.21395-1-hkelam@marvell.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Guillaume Nault says:

====================
selftests/net: Isolate l2_tos_ttl_inherit.sh in its own netns.

l2_tos_ttl_inherit.sh uses a veth pair to run its tests, but only one
of the veth interfaces runs in a dedicated netns. The other one remains
in the initial namespace where the existing network configuration can
interfere with the setup used for the tests.

Isolate both veth devices in their own netns and ensure everything gets
cleaned up when the script exits.

Link: https://lore.kernel.org/netdev/924f1062-ab59-9b88-3b43-c44e73a30387@alu.unizg.hr/
====================

Link: https://lore.kernel.org/r/cover.1673191942.git.gnault@redhat.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Use 'set -e' and an exit handler to stop the script if a command fails
and ensure the test environment is cleaned up in any case. Also, handle
the case where the script is interrupted by SIGINT.

The only command that's expected to fail is 'wait $ping_pid', since
it's killed by the script. Handle this case with '|| true' to make it
play well with 'set -e'.

Finally, return the Kselftest SKIP code (4) when the script breaks
because of an environment problem or a command line failure. The 0 and
1 return codes should now reliably indicate that all tests have been
run (0: all tests run and passed, 1: all tests run but at least one
failed, 4: test script didn't run completely).

Fixes: b690842d ("selftests/net: test l2 tunnel TOS/TTL inheriting")
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This selftest currently runs half in the current namespace and half in
a netns of its own. Therefore, the test can fail if the current
namespace is already configured with incompatible parameters (for
example if it already has a veth0 interface).

Adapt the script to put both ends of the veth pair in their own netns.
Now veth0 is created in NS0 instead of the current namespace, while
veth1 is set up in NS1 (instead of the 'testing' netns).

The user visible netns names are randomised to minimise the risk of
conflicts with already existing namespaces. The cleanup() function
doesn't need to remove the virtual interface anymore: deleting NS0 and
NS1 automatically removes the virtual interfaces they contained.

We can remove $ns, which was only used to run ip commands in the
'testing' netns (let's use the builtin "-netns" option instead).
However, we still need a similar functionality as ping and tcpdump
now need to run in NS0. So we now have $RUN_NS0 for that.

Fixes: b690842d ("selftests/net: test l2 tunnel TOS/TTL inheriting")
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The ping command can run before DAD completes. In that case, ping may
fail and break the selftest.

We don't need DAD here since we're working on isolated device pairs.

Fixes: b690842d ("selftests/net: test l2 tunnel TOS/TTL inheriting")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This reverts commit 42666b2c.

This chip version seems to be very rare, but it exits in consumer
devices, see linked report.

Link: https://stackoverflow.com/questions/75049473/cant-setup-a-wired-network-in-archlinux-fresh-install
Fixes: 42666b2c ("r8169: disable detection of chip version 36")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/42e9674c-d5d0-a65a-f578-e5c74f244739@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The 'TCA_MPLS_LABEL' attribute is of 'NLA_U32' type, but has a
validation type of 'NLA_VALIDATE_FUNCTION'. This is an invalid
combination according to the comment above 'struct nla_policy':

"
Meaning of `validate' field, use via NLA_POLICY_VALIDATE_FN:
   NLA_BINARY           Validation function called for the attribute.
   All other            Unused - but note that it's a union
"

This can trigger the warning [1] in nla_get_range_unsigned() when
validation of the attribute fails. Despite being of 'NLA_U32' type, the
associated 'min'/'max' fields in the policy are negative as they are
aliased by the 'validate' field.

Fix by changing the attribute type to 'NLA_BINARY' which is consistent
with the above comment and all other users of NLA_POLICY_VALIDATE_FN().
As a result, move the length validation to the validation function.

No regressions in MPLS tests:

 # ./tdc.py -f tc-tests/actions/mpls.json
 [...]
 # echo $?
 0

[1]
WARNING: CPU: 0 PID: 17743 at lib/nlattr.c:118
nla_get_range_unsigned+0x1d8/0x1e0 lib/nlattr.c:117
Modules linked in:
CPU: 0 PID: 17743 Comm: syz-executor.0 Not tainted 6.1.0-rc8 #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.13.0-48-gd9c812dda519-prebuilt.qemu.org 04/01/2014
RIP: 0010:nla_get_range_unsigned+0x1d8/0x1e0 lib/nlattr.c:117
[...]
Call Trace:
 <TASK>
 __netlink_policy_dump_write_attr+0x23d/0x990 net/netlink/policy.c:310
 netlink_policy_dump_write_attr+0x22/0x30 net/netlink/policy.c:411
 netlink_ack_tlv_fill net/netlink/af_netlink.c:2454 [inline]
 netlink_ack+0x546/0x760 net/netlink/af_netlink.c:2506
 netlink_rcv_skb+0x1b7/0x240 net/netlink/af_netlink.c:2546
 rtnetlink_rcv+0x18/0x20 net/core/rtnetlink.c:6109
 netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
 netlink_unicast+0x5e9/0x6b0 net/netlink/af_netlink.c:1345
 netlink_sendmsg+0x739/0x860 net/netlink/af_netlink.c:1921
 sock_sendmsg_nosec net/socket.c:714 [inline]
 sock_sendmsg net/socket.c:734 [inline]
 ____sys_sendmsg+0x38f/0x500 net/socket.c:2482
 ___sys_sendmsg net/socket.c:2536 [inline]
 __sys_sendmsg+0x197/0x230 net/socket.c:2565
 __do_sys_sendmsg net/socket.c:2574 [inline]
 __se_sys_sendmsg net/socket.c:2572 [inline]
 __x64_sys_sendmsg+0x42/0x50 net/socket.c:2572
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x63/0xcd

Link: https://lore.kernel.org/netdev/CAO4mrfdmjvRUNbDyP0R03_DrD_eFCLCguz6OxZ2TYRSv0K9gxA@mail.gmail.com/
Fixes: 2a2ea508 ("net: sched: add mpls manipulation actions to TC")
Reported-by: Wei Chen <harperchen1110@gmail.com>
Tested-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/20230107171004.608436-1-idosch@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Adjust size parameter in connect() to match the type of the parameter, to
fix "No such file or directory" error in selftests/net/af_unix/
test_oob_unix.c:127.

The existing code happens to work provided that the autogenerated pathname
is shorter than sizeof (struct sockaddr), which is why it hasn't been
noticed earlier.

Visible from the trace excerpt:

bind(3, {sa_family=AF_UNIX, sun_path="unix_oob_453059"}, 110) = 0
clone(child_stack=NULL, flags=CLONE_CHILD_CLEARTID|CLONE_CHILD_SETTID|SIGCHLD, child_tidptr=0x7fa6a6577a10) = 453060
[pid <child>] connect(6, {sa_family=AF_UNIX, sun_path="unix_oob_45305"}, 16) = -1 ENOENT (No such file or directory)

BUG: The filename is trimmed to sizeof (struct sockaddr).

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Cc: Florian Westphal <fw@strlen.de>
Reviewed-by: Florian Westphal <fw@strlen.de>
Fixes: 314001f0 ("af_unix: Add OOB support")
Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The blamed commit implemented the vcap_operations to allow to add an
entry in the TCAM. One of the callbacks is to validate the supported
keysets. If the TCAM lookup was not enabled, then this will return
failure so no entries could be added.
This doesn't make much sense, as you can enable at a later point the
TCAM. Therefore change it such to allow entries in TCAM even it is not
enabled.

Fixes: 4426b78c ("net: lan966x: Add port keyset config and callback interface")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jaroslav reported a recent throughput regression with virtio_net
caused by blamed commit.

It is unclear if DODGY GSO packets coming from user space
can be accepted by GRO engine in the future with minimal
changes, and if there is any expected gain from it.

In the meantime, make sure to detect and flush DODGY packets.

Fixes: 5eddb249 ("gro: add support of (hw)gro packets to gro stack")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-and-bisected-by: Jaroslav Pulchart <jaroslav.pulchart@gooddata.com>
Cc: Coco Li <lixiaoyan@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a use-after-free that occurs in hcd when in_urb sent from
pn533_usb_send_frame() is completed earlier than out_urb. Its callback
frees the skb data in pn533_send_async_complete() that is used as a
transfer buffer of out_urb. Wait before sending in_urb until the
callback of out_urb is called. To modify the callback of out_urb alone,
separate the complete function of out_urb and ack_urb.

Found by a modified version of syzkaller.

BUG: KASAN: use-after-free in dummy_timer
Call Trace:
 memcpy (mm/kasan/shadow.c:65)
 dummy_perform_transfer (drivers/usb/gadget/udc/dummy_hcd.c:1352)
 transfer (drivers/usb/gadget/udc/dummy_hcd.c:1453)
 dummy_timer (drivers/usb/gadget/udc/dummy_hcd.c:1972)
 arch_static_branch (arch/x86/include/asm/jump_label.h:27)
 static_key_false (include/linux/jump_label.h:207)
 timer_expire_exit (include/trace/events/timer.h:127)
 call_timer_fn (kernel/time/timer.c:1475)
 expire_timers (kernel/time/timer.c:1519)
 __run_timers (kernel/time/timer.c:1790)
 run_timer_softirq (kernel/time/timer.c:1803)

Fixes: c46ee386 ("NFC: pn533: add NXP pn533 nfc device driver")
Signed-off-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Zero-length arrays are deprecated[1]. Replace struct
mlxsw_sp_nexthop_group_info's "nexthops" 0-length array with a flexible
array. Detected with GCC 13, using -fstrict-flex-arrays=3:

drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c: In function 'mlxsw_sp_nexthop_group_hash_obj':
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3278:38: warning: array subscript i is outside array bounds of 'struct mlxsw_sp_nexthop[0]' [-Warray-bounds=]
 3278 |                         val ^= jhash(&nh->ifindex, sizeof(nh->ifindex), seed);
      |                                      ^~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:2954:33: note: while referencing 'nexthops'
 2954 |         struct mlxsw_sp_nexthop nexthops[0];
      |                                 ^~~~~~~~

[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays

Cc: Ido Schimmel <idosch@nvidia.com>
Cc: Petr Machata <petrm@nvidia.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b310de78 ("net: ipa: add IPA v4.7 support") was merged
despite an unresolved comment made by Konrad Dybcio.  Konrad
observed that the IMEM region specified for IPA v4.7 did not match
that used downstream for the SM7225 SoC.  In "lagoon.dtsi" present
in a Sony Xperia source tree, a ipa_smmu_ap node was defined with a
"qcom,additional-mapping" property that defined the IPA IMEM area
starting at offset 0x146a8000 (not 0x146a9000 that was committed).

The IPA v4.7 target system used for testing uses the SM7225 SoC, so
we'll adhere what the downstream code specifies is the address of
the IMEM region used for IPA.

Link: https://lore.kernel.org/linux-arm-msm/20221208211529.757669-1-elder@linaro.org
Fixes: b310de78 ("net: ipa: add IPA v4.7 support")
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The introduction of support for Apple board types inadvertently changed
the precedence order, causing hybrid SMBIOS+DT platforms to look up the
firmware using the DMI information instead of the device tree compatible
to generate the board type. Revert back to the old behavior,
as affected platforms use firmwares named after the DT compatible.

Fixes: 7682de8b ("wifi: brcmfmac: of: Fetch Apple properties")

[1] https://bugzilla.opensuse.org/show_bug.cgi?id=1206697#c13

Cc: stable@vger.kernel.org
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Reviewed-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Howells says:

====================
rxrpc: Fix race between call connection, data transmit and call disconnect

Here are patches to fix an oops[1] caused by a race between call
connection, initial packet transmission and call disconnection which
results in something like:

        kernel BUG at net/rxrpc/peer_object.c:413!

when the syzbot test is run.  The problem is that the connection procedure
is effectively split across two threads and can get expanded by taking an
interrupt, thereby adding the call to the peer error distribution list
*after* it has been disconnected (say by the rxrpc socket shutting down).

The easiest solution is to look at the fourth set of I/O thread
conversion/SACK table expansion patches that didn't get applied[2] and take
from it those patches that move call connection and disconnection into the
I/O thread.  Moving these things into the I/O thread means that the
sequencing is managed by all being done in the same thread - and the race
can no longer happen.

This is preferable to introducing an extra lock as adding an extra lock
would make the I/O thread have to wait for the app thread in yet another
place.

The changes can be considered as a number of logical parts:

 (1) Move all of the call state changes into the I/O thread.

 (2) Make client connection ID space per-local endpoint so that the I/O
     thread doesn't need locks to access it.

 (3) Move actual abort generation into the I/O thread and clean it up.  If
     sendmsg or recvmsg want to cause an abort, they have to delegate it.

 (4) Offload the setting up of the security context on a connection to the
     thread of one of the apps that's starting a call.  We don't want to be
     doing any sort of crypto in the I/O thread.

 (5) Connect calls (ie. assign them to channel slots on connections) in the
     I/O thread.  Calls are set up by sendmsg/kafs and passed to the I/O
     thread to connect.  Connections are allocated in the I/O thread after
     this.

 (6) Disconnect calls in the I/O thread.

I've also added a patch for an unrelated bug that cropped up during
testing, whereby a race can occur between an incoming call and socket
shutdown.

Note that whilst this fixes the original syzbot bug, another bug may get
triggered if this one is fixed:

        INFO: rcu detected stall in corrupted
        rcu: INFO: rcu_preempt detected expedited stalls on CPUs/tasks: { P5792 } 2657 jiffies s: 2825 root: 0x0/T
        rcu: blocking rcu_node structures (internal RCU debug):

It doesn't look this should be anything to do with rxrpc, though, as I've
tested an additional patch[3] that removes practically all the RCU usage
from rxrpc and it still occurs.  It seems likely that it is being caused by
something in the tunnelling setup that the syzbot test does, but there's
not enough info to go on.  It also seems unlikely to be anything to do with
the afs driver as the test doesn't use that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

An incoming call can race with rxrpc socket destruction, leading to a
leaked call.  This may result in an oops when the call timer eventually
expires:

   BUG: kernel NULL pointer dereference, address: 0000000000000874
   RIP: 0010:_raw_spin_lock_irqsave+0x2a/0x50
   Call Trace:
    <IRQ>
    try_to_wake_up+0x59/0x550
    ? __local_bh_enable_ip+0x37/0x80
    ? rxrpc_poke_call+0x52/0x110 [rxrpc]
    ? rxrpc_poke_call+0x110/0x110 [rxrpc]
    ? rxrpc_poke_call+0x110/0x110 [rxrpc]
    call_timer_fn+0x24/0x120

with a warning in the kernel log looking something like:

   rxrpc: Call 00000000ba5e571a still in use (1,SvAwtACK,1061d,0)!

incurred during rmmod of rxrpc.  The 1061d is the call flags:

   RECVMSG_READ_ALL, RX_HEARD, BEGAN_RX_TIMER, RX_LAST, EXPOSED,
   IS_SERVICE, RELEASED

but no DISCONNECTED flag (0x800), so it's an incoming (service) call and
it's still connected.

The race appears to be that:

 (1) rxrpc_new_incoming_call() consults the service struct, checks sk_state
     and allocates a call - then pauses, possibly for an interrupt.

 (2) rxrpc_release_sock() sets RXRPC_CLOSE, nulls the service pointer,
     discards the prealloc and releases all calls attached to the socket.

 (3) rxrpc_new_incoming_call() resumes, launching the new call, including
     its timer and attaching it to the socket.

Fix this by read-locking local->services_lock to access the AF_RXRPC socket
providing the service rather than RCU in rxrpc_new_incoming_call().
There's no real need to use RCU here as local->services_lock is only
write-locked by the socket side in two places: when binding and when
shutting down.

Fixes: 5e6ef4f1 ("rxrpc: Make the I/O thread take over the call and local processor work")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org

PF netdev can request AF to enable or disable reception and transmission
on assigned CGX::LMAC. The current code instead of disabling or enabling
'reception and transmission' also disables/enable the LMAC. This patch
fixes this issue.

Fixes: 1435f66a ("octeontx2-af: CGX Rx/Tx enable/disable mbox handlers")
Signed-off-by: Angela Czubak <aczubak@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230105160107.17638-1-hkelam@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This unexpected behavior is observed:

node 1                    | node 2
------                    | ------
link is established       | link is established
reboot                    | link is reset
up                        | send discovery message
receive discovery message |
link is established       | link is established
send discovery message    |
                          | receive discovery message
                          | link is reset (unexpected)
                          | send reset message
link is reset             |

It is due to delayed re-discovery as described in function
tipc_node_check_dest(): "this link endpoint has already reset
and re-established contact with the peer, before receiving a
discovery message from that node."

However, commit 598411d7 has changed the condition for calling
tipc_node_link_down() which was the acceptance of new media address.

This commit fixes this by restoring the old and correct behavior.

Fixes: 598411d7 ("tipc: make resetting of links non-atomic")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the connection setup of client calls to the I/O thread so that a whole
load of locking and barrierage can be eliminated.  This necessitates the
app thread waiting for connection to complete before it can begin
encrypting data.

This also completes the fix for a race that exists between call connection
and call disconnection whereby the data transmission code adds the call to
the peer error distribution list after the call has been disconnected (say
by the rxrpc socket getting closed).

The fix is to complete the process of moving call connection, data
transmission and call disconnection into the I/O thread and thus forcibly
serialising them.

Note that the issue may predate the overhaul to an I/O thread model that
were included in the merge window for v6.2, but the timing is very much
changed by the change given below.

Fixes: cf37b598 ("rxrpc: Move DATA transmission into call processor work item")
Reported-by: syzbot+c22650d2844392afdcfd@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Move the management of the client connection cache to the I/O thread rather
than managing it from the namespace as an aggregate across all the local
endpoints within the namespace.

This will allow a load of locking to be got rid of in a future patch as
only the I/O thread will be looking at the this.

The downside is that the total number of cached connections on the system
can get higher because the limit is now per-local rather than per-netns.
We can, however, keep the number of client conns in use across the entire
netfs and use that to reduce the expiration time of idle connection.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

All the setters of call->state are now in the I/O thread and thus the state
lock is now unnecessary.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Move the call state changes that are made in rxrpc_recvmsg() to the I/O
thread.  This means that, thenceforth, only the I/O thread does this and
the call state lock can be removed.

This requires the Rx phase to be ended when the last packet is received,
not when it is processed.

Since this now changes the rxrpc call state to SUCCEEDED before we've
consumed all the data from it, rxrpc_kernel_check_life() mustn't say the
call is dead until the recvmsg queue is empty (unless the call has failed).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Move all the call state changes that are made in rxrpc_sendmsg() to the I/O
thread.  This is a step towards removing the call state lock.

This requires the switch to the RXRPC_CALL_CLIENT_AWAIT_REPLY and
RXRPC_CALL_SERVER_SEND_REPLY states to be done when the last packet is
decanted from ->tx_sendmsg to ->tx_buffer in the I/O thread, not when it is
added to ->tx_sendmsg by sendmsg().
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Wrap accesses to get the state of a call from outside of the I/O thread in
a single place so that the barrier needed to order wrt the error code and
abort code is in just that place.

Also use a barrier when setting the call state and again when reading the
call state such that the auxiliary completion info (error code, abort code)
can be read without taking a read lock on the call state lock.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Split out the functions that change the state of an rxrpc call into their
own file.  The idea being to remove anything to do with changing the state
of a call directly from the rxrpc sendmsg() and recvmsg() paths and have
all that done in the I/O thread only, with the ultimate aim of removing the
state lock entirely.  Moving the code out of sendmsg.c and recvmsg.c makes
that easier to manage.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Use the information now stored in struct rxrpc_call to configure the
connection bundle and thence the connection, rather than using the
rxrpc_conn_parameters struct.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Offload the completion of the challenge/response cycle on a service
connection to the I/O thread.  After the RESPONSE packet has been
successfully decrypted and verified by the work queue, offloading the
changing of the call states to the I/O thread makes iteration over the
conn's channel list simpler.

Do this by marking the RESPONSE skbuff and putting it onto the receive
queue for the I/O thread to collect.  We put it on the front of the queue
as we've already received the packet for it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Make the set of connection IDs per local endpoint so that endpoints don't
cause each other's connections to get dismissed.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Tidy up the abort generation infrastructure in the following ways:

 (1) Create an enum and string mapping table to list the reasons an abort
     might be generated in tracing.

 (2) Replace the 3-char string with the values from (1) in the places that
     use that to log the abort source.  This gets rid of a memcpy() in the
     tracepoint.

 (3) Subsume the rxrpc_rx_eproto tracepoint with the rxrpc_abort tracepoint
     and use values from (1) to indicate the trace reason.

 (4) Always make a call to an abort function at the point of the abort
     rather than stashing the values into variables and using goto to get
     to a place where it reported.  The C optimiser will collapse the calls
     together as appropriate.  The abort functions return a value that can
     be returned directly if appropriate.

Note that this extends into afs also at the points where that generates an
abort.  To aid with this, the afs sources need to #define
RXRPC_TRACE_ONLY_DEFINE_ENUMS before including the rxrpc tracing header
because they don't have access to the rxrpc internal structures that some
of the tracepoints make use of.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Clean up connection abort, using the connection state_lock to gate access
to change that state, and use an rxrpc_call_completion value to indicate
the difference between local and remote aborts as these can be pasted
directly into the call state.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Provide a means by which an event notification can be sent to a connection
through such that the I/O thread can pick it up and handle it rather than
doing it in a separate workqueue.

This is then used to move the deferred final ACK of a call into the I/O
thread rather than a separate work queue as part of the drive to do all
transmission from the I/O thread.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Only perform call disconnection in the I/O thread to reduce the locking
requirement.

This is the first part of a fix for a race that exists between call
connection and call disconnection whereby the data transmission code adds
the call to the peer error distribution list after the call has been
disconnected (say by the rxrpc socket getting closed).

The fix is to complete the process of moving call connection, data
transmission and call disconnection into the I/O thread and thus forcibly
serialising them.

Note that the issue may predate the overhaul to an I/O thread model that
were included in the merge window for v6.2, but the timing is very much
changed by the change given below.

Fixes: cf37b598 ("rxrpc: Move DATA transmission into call processor work item")
Reported-by: syzbot+c22650d2844392afdcfd@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Only set the abort call completion state in the I/O thread and only
transmit ABORT packets from there.  rxrpc_abort_call() can then be made to
actually send the packet.

Further, ABORT packets should only be sent if the call has been exposed to
the network (ie. at least one attempted DATA transmission has occurred for
it).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Call the rxrpc_conn_retransmit_call() directly from rxrpc_input_packet()
rather than calling it via connection event handling.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Make the local endpoint and it's I/O thread hold a reference on a connected
call until that call is disconnected.  Without this, we're reliant on
either the AF_RXRPC socket to hold a ref (which is dropped when the call is
released) or a queued work item to hold a ref (the work item is being
replaced with the I/O thread).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

Stash the network namespace pointer in the rxrpc_local struct in addition
to a pointer to the rxrpc-specific net namespace info.  Use this to remove
some places where the socket is passed as a parameter.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org

This modem has 7 interfaces, 5 of them are serial interfaces and are
driven by cdc_acm, while 2 of them are wwan interfaces and are driven
by cdc_ether:
If 0: Abstract (modem)
If 1: Abstract (modem)
If 2: Abstract (modem)
If 3: Abstract (modem)
If 4: Abstract (modem)
If 5: Ethernet Networking
If 6: Ethernet Networking

Without this change, the 2 network interfaces will be named to usb0
and usb1, our QA think the names are confusing and filed a bug on it.

After applying this change, the name will be wwan0 and wwan1, and
they could work well with modem manager.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20230105034249.10433-1-hui.wang@canonical.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In current driver, MAC will always enable 2ns delay in RGMII mode,
but that's not the correct usage.

Remove the dwmac_fix_mac_speed() in driver, and recommend "rgmii-id"
for phy-mode in device tree.

Fixes: f2d356a6 ("stmmac: dwmac-mediatek: add support for mt8195")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf, wifi, and netfilter.

  Current release - regressions:

   - bpf: fix nullness propagation for reg to reg comparisons, avoid
     null-deref

   - inet: control sockets should not use current thread task_frag

   - bpf: always use maximal size for copy_array()

   - eth: bnxt_en: don't link netdev to a devlink port for VFs

  Current release - new code bugs:

   - rxrpc: fix a couple of potential use-after-frees

   - netfilter: conntrack: fix IPv6 exthdr error check

   - wifi: iwlwifi: fw: skip PPAG for JF, avoid FW crashes

   - eth: dsa: qca8k: various fixes for the in-band register access

   - eth: nfp: fix schedule in atomic context when sync mc address

   - eth: renesas: rswitch: fix getting mac address from device tree

   - mobile: ipa: use proper endpoint mask for suspend

  Previous releases - regressions:

   - tcp: add TIME_WAIT sockets in bhash2, fix regression caught by
     Jiri / python tests

   - net: tc: don't intepret cls results when asked to drop, fix
     oob-access

   - vrf: determine the dst using the original ifindex for multicast

   - eth: bnxt_en:
      - fix XDP RX path if BPF adjusted packet length
      - fix HDS (header placement) and jumbo thresholds for RX packets

   - eth: ice: xsk: do not use xdp_return_frame() on tx_buf->raw_buf,
     avoid memory corruptions

  Previous releases - always broken:

   - ulp: prevent ULP without clone op from entering the LISTEN status

   - veth: fix race with AF_XDP exposing old or uninitialized
     descriptors

   - bpf:
      - pull before calling skb_postpull_rcsum() (fix checksum support
        and avoid a WARN())
      - fix panic due to wrong pageattr of im->image (when livepatch and
        kretfunc coexist)
      - keep a reference to the mm, in case the task is dead

   - mptcp: fix deadlock in fastopen error path

   - netfilter:
      - nf_tables: perform type checking for existing sets
      - nf_tables: honor set timeout and garbage collection updates
      - ipset: fix hash:net,port,net hang with /0 subnet
      - ipset: avoid hung task warning when adding/deleting entries

   - selftests: net:
      - fix cmsg_so_mark.sh test hang on non-x86 systems
      - fix the arp_ndisc_evict_nocarrier test for IPv6

   - usb: rndis_host: secure rndis_query check against int overflow

   - eth: r8169: fix dmar pte write access during suspend/resume with
     WOL

   - eth: lan966x: fix configuration of the PCS

   - eth: sparx5: fix reading of the MAC address

   - eth: qed: allow sleep in qed_mcp_trace_dump()

   - eth: hns3:
      - fix interrupts re-initialization after VF FLR
      - fix handling of promisc when MAC addr table gets full
      - refine the handling for VF heartbeat

   - eth: mlx5:
      - properly handle ingress QinQ-tagged packets on VST
      - fix io_eq_size and event_eq_size params validation on big endian
      - fix RoCE setting at HCA level if not supported at all
      - don't turn CQE compression on by default for IPoIB

   - eth: ena:
      - fix toeplitz initial hash key value
      - account for the number of XDP-processed bytes in interface stats
      - fix rx_copybreak value update

  Misc:

   - ethtool: harden phy stat handling against buggy drivers

   - docs: netdev: convert maintainer's doc from FAQ to a normal
     document"

* tag 'net-6.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (112 commits)
  caif: fix memory leak in cfctrl_linkup_request()
  inet: control sockets should not use current thread task_frag
  net/ulp: prevent ULP without clone op from entering the LISTEN status
  qed: allow sleep in qed_mcp_trace_dump()
  MAINTAINERS: Update maintainers for ptp_vmw driver
  usb: rndis_host: Secure rndis_query check against int overflow
  net: dpaa: Fix dtsec check for PCS availability
  octeontx2-pf: Fix lmtst ID used in aura free
  drivers/net/bonding/bond_3ad: return when there's no aggregator
  netfilter: ipset: Rework long task execution when adding/deleting entries
  netfilter: ipset: fix hash:net,port,net hang with /0 subnet
  net: sparx5: Fix reading of the MAC address
  vxlan: Fix memory leaks in error path
  net: sched: htb: fix htb_classify() kernel-doc
  net: sched: cbq: dont intepret cls results when asked to drop
  net: sched: atm: dont intepret cls results when asked to drop
  dt-bindings: net: marvell,orion-mdio: Fix examples
  dt-bindings: net: sun8i-emac: Add phy-supply property
  net: ipa: use proper endpoint mask for suspend
  selftests: net: return non-zero for failures reported in arp_ndisc_evict_nocarrier
  ...