This patch is to enable Intel SERDES power up/down sequence. The SERDES
converts 8/10 bits data to SGMII signal. Below is an example of
HW configuration for SGMII mode. The SERDES is located in the PHY IF
in the diagram below.

<-----------------GBE Controller---------->|<--External PHY chip-->
+----------+         +----+            +---+           +----------+
|   EQoS   | <-GMII->| DW | < ------ > |PHY| <-SGMII-> | External |
|   MAC    |         |xPCS|            |IF |           | PHY      |
+----------+         +----+            +---+           +----------+
       ^               ^                 ^                ^
       |               |                 |                |
       +---------------------MDIO-------------------------+

PHY IF configuration and status registers are accessible through
mdio address 0x15 which is defined as mdio_adhoc_addr. During D0,
The driver will need to power up PHY IF by changing the power state
to P0. Likewise, for D3, the driver sets PHY IF power state to P3.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the function devm_platform_ioremap_resource_byname() to simplify
source code which calls the functions platform_get_resource_byname()
and devm_ioremap_resource(). Remove also a few error messages which
became unnecessary with this software refactoring.
Suggested-by: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the macvlan_device_event(), the list_first_entry_or_null() is used.
This function could return null pointer if there is no node.
But, the macvlan module doesn't check the null pointer.
So, null-ptr-deref would occur.

      bond0
        |
   +----+-----+
   |          |
macvlan0   macvlan1
   |          |
 dummy0     dummy1

The problem scenario.
If dummy1 is removed,
1. ->dellink() of dummy1 is called.
2. NETDEV_UNREGISTER of dummy1 notification is sent to macvlan module.
3. ->dellink() of macvlan1 is called.
4. NETDEV_UNREGISTER of macvlan1 notification is sent to bond module.
5. __bond_release_one() is called and it internally calls
   dev_set_mac_address().
6. dev_set_mac_address() calls the ->ndo_set_mac_address() of macvlan1,
   which is macvlan_set_mac_address().
7. macvlan_set_mac_address() calls the dev_set_mac_address() with dummy1.
8. NETDEV_CHANGEADDR of dummy1 is sent to macvlan module.
9. In the macvlan_device_event(), it calls list_first_entry_or_null().
At this point, dummy1 and macvlan1 were removed.
So, list_first_entry_or_null() will return NULL.

Test commands:
    ip netns add nst
    ip netns exec nst ip link add bond0 type bond
    for i in {0..10}
    do
        ip netns exec nst ip link add dummy$i type dummy
	ip netns exec nst ip link add macvlan$i link dummy$i \
		type macvlan mode passthru
	ip netns exec nst ip link set macvlan$i master bond0
    done
    ip netns del nst

Splat looks like:
[   40.585687][  T146] general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP DEI
[   40.587249][  T146] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[   40.588342][  T146] CPU: 1 PID: 146 Comm: kworker/u8:2 Not tainted 5.7.0-rc1+ #532
[   40.589299][  T146] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   40.590469][  T146] Workqueue: netns cleanup_net
[   40.591045][  T146] RIP: 0010:macvlan_device_event+0x4e2/0x900 [macvlan]
[   40.591905][  T146] Code: 00 00 00 00 00 fc ff df 80 3c 06 00 0f 85 45 02 00 00 48 89 da 48 b8 00 00 00 00 00 fc ff d2
[   40.594126][  T146] RSP: 0018:ffff88806116f4a0 EFLAGS: 00010246
[   40.594783][  T146] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
[   40.595653][  T146] RDX: 0000000000000000 RSI: ffff88806547ddd8 RDI: ffff8880540f1360
[   40.596495][  T146] RBP: ffff88804011a808 R08: fffffbfff4fb8421 R09: fffffbfff4fb8421
[   40.597377][  T146] R10: ffffffffa7dc2107 R11: 0000000000000000 R12: 0000000000000008
[   40.598186][  T146] R13: ffff88804011a000 R14: ffff8880540f1000 R15: 1ffff1100c22de9a
[   40.599012][  T146] FS:  0000000000000000(0000) GS:ffff888067800000(0000) knlGS:0000000000000000
[   40.600004][  T146] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   40.600665][  T146] CR2: 00005572d3a807b8 CR3: 000000005fcf4003 CR4: 00000000000606e0
[   40.601485][  T146] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   40.602461][  T146] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   40.603443][  T146] Call Trace:
[   40.603871][  T146]  ? nf_tables_dump_setelem+0xa0/0xa0 [nf_tables]
[   40.604587][  T146]  ? macvlan_uninit+0x100/0x100 [macvlan]
[   40.605212][  T146]  ? __module_text_address+0x13/0x140
[   40.605842][  T146]  notifier_call_chain+0x90/0x160
[   40.606477][  T146]  dev_set_mac_address+0x28e/0x3f0
[   40.607117][  T146]  ? netdev_notify_peers+0xc0/0xc0
[   40.607762][  T146]  ? __module_text_address+0x13/0x140
[   40.608440][  T146]  ? notifier_call_chain+0x90/0x160
[   40.609097][  T146]  ? dev_set_mac_address+0x1f0/0x3f0
[   40.609758][  T146]  dev_set_mac_address+0x1f0/0x3f0
[   40.610402][  T146]  ? __local_bh_enable_ip+0xe9/0x1b0
[   40.611071][  T146]  ? bond_hw_addr_flush+0x77/0x100 [bonding]
[   40.611823][  T146]  ? netdev_notify_peers+0xc0/0xc0
[   40.612461][  T146]  ? bond_hw_addr_flush+0x77/0x100 [bonding]
[   40.613213][  T146]  ? bond_hw_addr_flush+0x77/0x100 [bonding]
[   40.613963][  T146]  ? __local_bh_enable_ip+0xe9/0x1b0
[   40.614631][  T146]  ? bond_time_in_interval.isra.31+0x90/0x90 [bonding]
[   40.615484][  T146]  ? __bond_release_one+0x9f0/0x12c0 [bonding]
[   40.616230][  T146]  __bond_release_one+0x9f0/0x12c0 [bonding]
[   40.616949][  T146]  ? bond_enslave+0x47c0/0x47c0 [bonding]
[   40.617642][  T146]  ? lock_downgrade+0x730/0x730
[   40.618218][  T146]  ? check_flags.part.42+0x450/0x450
[   40.618850][  T146]  ? __mutex_unlock_slowpath+0xd0/0x670
[   40.619519][  T146]  ? trace_hardirqs_on+0x30/0x180
[   40.620117][  T146]  ? wait_for_completion+0x250/0x250
[   40.620754][  T146]  bond_netdev_event+0x822/0x970 [bonding]
[   40.621460][  T146]  ? __module_text_address+0x13/0x140
[   40.622097][  T146]  notifier_call_chain+0x90/0x160
[   40.622806][  T146]  rollback_registered_many+0x660/0xcf0
[   40.623522][  T146]  ? netif_set_real_num_tx_queues+0x780/0x780
[   40.624290][  T146]  ? notifier_call_chain+0x90/0x160
[   40.624957][  T146]  ? netdev_upper_dev_unlink+0x114/0x180
[   40.625686][  T146]  ? __netdev_adjacent_dev_unlink_neighbour+0x30/0x30
[   40.626421][  T146]  ? mutex_is_locked+0x13/0x50
[   40.627016][  T146]  ? unregister_netdevice_queue+0xf2/0x240
[   40.627663][  T146]  unregister_netdevice_many.part.134+0x13/0x1b0
[   40.628362][  T146]  default_device_exit_batch+0x2d9/0x390
[   40.628987][  T146]  ? unregister_netdevice_many+0x40/0x40
[   40.629615][  T146]  ? dev_change_net_namespace+0xcb0/0xcb0
[   40.630279][  T146]  ? prepare_to_wait_exclusive+0x2e0/0x2e0
[   40.630943][  T146]  ? ops_exit_list.isra.9+0x97/0x140
[   40.631554][  T146]  cleanup_net+0x441/0x890
[ ... ]

Fixes: e289fd28 ("macvlan: fix the problem when mac address changes for passthru mode")
Reported-by: syzbot+5035b1f9dc7ea4558d5a@syzkaller.appspotmail.com
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:

drivers/net/ethernet/intel/e1000/e1000_main.c:1479:44-49: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:

drivers/net/ethernet/intel/i40e/i40e_main.c:1614:52-57: WARNING:
conversion to bool not needed here
drivers/net/ethernet/intel/i40e/i40e_main.c:11439:52-57: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:

drivers/ptp/ptp_ines.c:403:55-60: WARNING: conversion to bool not
needed here
drivers/ptp/ptp_ines.c:404:55-60: WARNING: conversion to bool not
needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 018d26fc ("cgroup, netclassid: periodically release file_lock
on classid") added a second cond_resched to write_classid indirectly by
update_classid_task. Remove the one in write_classid.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Dmitry Yakunin <zeil@yandex-team.ru>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

1) flow_block_cb memleak in nf_flow_table_offload_del_cb(), from Roi Dayan.

2) Fix error path handling in nf_nat_inet_register_fn(), from Hillf Danton.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx5-fixes-2020-04-20
Signed-off-by: David S. Miller <davem@davemloft.net>

In the switchdev mode, when running "cat
/sys/class/net/NIC/statistics/tx_packets", the ppcnt register is
accessed to get the latest values. But currently this command can
not get the correct values from ppcnt.

From firmware manual, before getting the 802_3 counters, the 802_3
data layout should be set to the ppcnt register.

When the command "cat /sys/class/net/NIC/statistics/tx_packets" is
run, before updating 802_3 data layout with ppcnt register, the
monitor counters are tested. The test result will decide the
802_3 data layout is updated or not.

Actually the monitor counters do not support to monitor rx/tx
stats of 802_3 in switchdev mode. So the rx/tx counters change
will not trigger monitor counters. So the 802_3 data layout will
not be updated in ppcnt register. Finally this command can not get
the latest values from ppcnt register with 802_3 data layout.

Fixes: 5c7e8bbb ("net/mlx5e: Use monitor counters for update stats")
Signed-off-by: Zhu Yanjun <yanjunz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

MLX5_CORE uses the 'imply' keyword to depend on VXLAN, PTP_1588_CLOCK,
MLXFW and PCI_HYPERV_INTERFACE.

This was useful to force vxlan, ptp, etc.. to be reachable to mlx5
regardless of their config states.

Due to the changes in the cited commit below, the semantics of 'imply'
was changed to not force any restriction on the implied config.

As a result of this change, the compilation of MLX5_CORE=y and VXLAN=m
would result in undefined references, as VXLAN now would stay as 'm'.

To fix this we change MLX5_CORE to have a weak dependency on
these modules/configs and make sure they are reachable, by adding:
depend on symbol || !symbol.

For example: VXLAN=m MLX5_CORE=y, this will force MLX5_CORE to m

Fixes: def2fbff ("kconfig: allow symbols implied by y to become m")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Reported-by: Randy Dunlap <rdunlap@infradead.org>

XSK wakeup function triggers NAPI by posting a NOP WQE to a special XSK
ICOSQ. When the application floods the driver with wakeup requests by
calling sendto() in a certain pattern that ends up in mlx5e_trigger_irq,
the XSK ICOSQ may overflow.

Multiple NOPs are not required and won't accelerate the process, so
avoid posting a second NOP if there is one already on the way. This way
we also avoid increasing the queue size (which might not help anyway).

Fixes: db05815b ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

After allowing parallel tuple insertion, we get the following trace:

[ 5505.142249] ------------[ cut here ]------------
[ 5505.148155] WARNING: CPU: 21 PID: 13313 at lib/radix-tree.c:581 delete_node+0x16c/0x180
[ 5505.295553] CPU: 21 PID: 13313 Comm: kworker/u50:22 Tainted: G           OE     5.6.0+ #78
[ 5505.304824] Hardware name: Supermicro Super Server/X10DRT-P, BIOS 2.0b 03/30/2017
[ 5505.313740] Workqueue: nf_flow_table_offload flow_offload_work_handler [nf_flow_table]
[ 5505.323257] RIP: 0010:delete_node+0x16c/0x180
[ 5505.349862] RSP: 0018:ffffb19184eb7b30 EFLAGS: 00010282
[ 5505.356785] RAX: 0000000000000000 RBX: ffff904ac95b86d8 RCX: ffff904b6f938838
[ 5505.365190] RDX: 0000000000000000 RSI: ffff904ac954b908 RDI: ffff904ac954b920
[ 5505.373628] RBP: ffff904b4ac13060 R08: 0000000000000001 R09: 0000000000000000
[ 5505.382155] R10: 0000000000000000 R11: 0000000000000040 R12: 0000000000000000
[ 5505.390527] R13: ffffb19184eb7bfc R14: ffff904b6bef5800 R15: ffff90482c1203c0
[ 5505.399246] FS:  0000000000000000(0000) GS:ffff904c2fc80000(0000) knlGS:0000000000000000
[ 5505.408621] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5505.415739] CR2: 00007f5d27006010 CR3: 0000000058c10006 CR4: 00000000001626e0
[ 5505.424547] Call Trace:
[ 5505.428429]  idr_alloc_u32+0x7b/0xc0
[ 5505.433803]  mlx5_tc_ct_entry_add_rule+0xbf/0x950 [mlx5_core]
[ 5505.441354]  ? mlx5_fc_create+0x23c/0x370 [mlx5_core]
[ 5505.448225]  mlx5_tc_ct_block_flow_offload+0x874/0x10b0 [mlx5_core]
[ 5505.456278]  ? mlx5_tc_ct_block_flow_offload+0x63d/0x10b0 [mlx5_core]
[ 5505.464532]  nf_flow_offload_tuple.isra.21+0xc5/0x140 [nf_flow_table]
[ 5505.472286]  ? __kmalloc+0x217/0x2f0
[ 5505.477093]  ? flow_rule_alloc+0x1c/0x30
[ 5505.482117]  flow_offload_work_handler+0x1d0/0x290 [nf_flow_table]
[ 5505.489674]  ? process_one_work+0x17c/0x580
[ 5505.494922]  process_one_work+0x202/0x580
[ 5505.500082]  ? process_one_work+0x17c/0x580
[ 5505.505696]  worker_thread+0x4c/0x3f0
[ 5505.510458]  kthread+0x103/0x140
[ 5505.514989]  ? process_one_work+0x580/0x580
[ 5505.520616]  ? kthread_bind+0x10/0x10
[ 5505.525837]  ret_from_fork+0x3a/0x50
[ 5505.570841] ---[ end trace 07995de9c56d6831 ]---

This happens from parallel deletes/adds to idr, as idr isn't protected.
Fix that by using xarray as the tuple_ids allocator instead of idr.

Fixes: 7da182a9 ("netfilter: flowtable: Use work entry per offload command")
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

On s390 FORCE_MAX_ZONEORDER is 9 instead of 11, thus a larger kzalloc()
allocation as done for the firmware tracer will always fail.

Looking at mlx5_fw_tracer_save_trace(), it is actually the driver itself
that copies the debug data into the trace array and there is no need for
the allocation to be contiguous in physical memory. We can therefor use
kvzalloc() instead of kzalloc() and get rid of the large contiguous
allcoation.

Fixes: f53aaa31 ("net/mlx5: FW tracer, implement tracer logic")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When team mode is changed or set, the team_mode_get() is called to check
whether the mode module is inserted or not. If the mode module is not
inserted, it calls the request_module().
In the request_module(), it creates a child process, which is
the "modprobe" process and waits for the done of the child process.
At this point, the following locks were used.
down_read(&cb_lock()); by genl_rcv()
    genl_lock(); by genl_rcv_msc()
        rtnl_lock(); by team_nl_cmd_options_set()
            mutex_lock(&team->lock); by team_nl_team_get()

Concurrently, the team module could be removed by rmmod or "modprobe -r"
The __exit function of team module is team_module_exit(), which calls
team_nl_fini() and it tries to acquire following locks.
down_write(&cb_lock);
    genl_lock();
Because of the genl_lock() and cb_lock, this process can't be finished
earlier than request_module() routine.

The problem secenario.
CPU0                                     CPU1
team_mode_get
    request_module()
                                         modprobe -r team_mode_roundrobin
                                                     team <--(B)
        modprobe team <--(A)
            team_mode_roundrobin

By request_module(), the "modprobe team_mode_roundrobin" command
will be executed. At this point, the modprobe process will decide
that the team module should be inserted before team_mode_roundrobin.
Because the team module is being removed.

By the module infrastructure, the same module insert/remove operations
can't be executed concurrently.
So, (A) waits for (B) but (B) also waits for (A) because of locks.
So that the hang occurs at this point.

Test commands:
    while :
    do
        teamd -d &
	killall teamd &
	modprobe -rv team_mode_roundrobin &
    done

The approach of this patch is to hold the reference count of the team
module if the team module is compiled as a module. If the reference count
of the team module is not zero while request_module() is being called,
the team module will not be removed at that moment.
So that the above scenario could not occur.

Fixes: 3d249d4c ("net: introduce ethernet teaming device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paolo Abeni says:

====================
mptcp: fix races on accept()

This series includes some fixes for accept() races which may cause inconsistent
MPTCP socket status and oops. Please see the individual patches for the
technical details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't need them, as we can use the current ingress opt
data instead. Setting them in syn_recv_sock() may causes
inconsistent mptcp socket status, as per previous commit.

Fixes: cc7972ea ("mptcp: parse and emit MP_CAPABLE option according to v1 spec")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If multiple CPUs races on the same req_sock in syn_recv_sock(),
flipping such field can cause inconsistent child socket status.

When racing, the CPU losing the req ownership may still change
the mptcp request socket mp_capable flag while the CPU owning
the request is cloning the socket, leaving the child socket with
'is_mptcp' set but no 'mp_capable' flag.

Such socket will stay with 'conn' field cleared, heading to oops
in later mptcp callback.

Address the issue tracking the fallback status in a local variable.

Fixes: 58b09919 ("mptcp: create msk early")
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following splat can occur during self test:

 BUG: KASAN: use-after-free in subflow_data_ready+0x156/0x160
 Read of size 8 at addr ffff888100c35c28 by task mptcp_connect/4808

  subflow_data_ready+0x156/0x160
  tcp_child_process+0x6a3/0xb30
  tcp_v4_rcv+0x2231/0x3730
  ip_protocol_deliver_rcu+0x5c/0x860
  ip_local_deliver_finish+0x220/0x360
  ip_local_deliver+0x1c8/0x4e0
  ip_rcv_finish+0x1da/0x2f0
  ip_rcv+0xd0/0x3c0
  __netif_receive_skb_one_core+0xf5/0x160
  __netif_receive_skb+0x27/0x1c0
  process_backlog+0x21e/0x780
  net_rx_action+0x35f/0xe90
  do_softirq+0x4c/0x50
  [..]

This occurs when accessing subflow_ctx->conn.

Problem is that tcp_child_process() calls listen sockets'
sk_data_ready() notification, but it doesn't hold the listener
lock.  Another cpu calling close() on the listener will then cause
transition of refcount to 0.

Fixes: 58b09919 ("mptcp: create msk early")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fetching PTP sync information from mailbox is slow and can take
up to 10 milliseconds. Reduce this unnecessary delay by directly
reading the information from the corresponding registers.

Fixes: 9c33e420 ("cxgb4: Add PTP Hardware Clock (PHC) support")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Running with KASAN on a VIM3L systems leads to the following splat
when probing the Ethernet device:

==================================================================
BUG: KASAN: global-out-of-bounds in _get_maxdiv+0x74/0xd8
Read of size 4 at addr ffffa000090615f4 by task systemd-udevd/139
CPU: 1 PID: 139 Comm: systemd-udevd Tainted: G            E     5.7.0-rc1-00101-g8624b7577b9c #781
Hardware name: amlogic w400/w400, BIOS 2020.01-rc5 03/12/2020
Call trace:
 dump_backtrace+0x0/0x2a0
 show_stack+0x20/0x30
 dump_stack+0xec/0x148
 print_address_description.isra.12+0x70/0x35c
 __kasan_report+0xfc/0x1d4
 kasan_report+0x4c/0x68
 __asan_load4+0x9c/0xd8
 _get_maxdiv+0x74/0xd8
 clk_divider_bestdiv+0x74/0x5e0
 clk_divider_round_rate+0x80/0x1a8
 clk_core_determine_round_nolock.part.9+0x9c/0xd0
 clk_core_round_rate_nolock+0xf0/0x108
 clk_hw_round_rate+0xac/0xf0
 clk_factor_round_rate+0xb8/0xd0
 clk_core_determine_round_nolock.part.9+0x9c/0xd0
 clk_core_round_rate_nolock+0xf0/0x108
 clk_core_round_rate_nolock+0xbc/0x108
 clk_core_set_rate_nolock+0xc4/0x2e8
 clk_set_rate+0x58/0xe0
 meson8b_dwmac_probe+0x588/0x72c [dwmac_meson8b]
 platform_drv_probe+0x78/0xd8
 really_probe+0x158/0x610
 driver_probe_device+0x140/0x1b0
 device_driver_attach+0xa4/0xb0
 __driver_attach+0xcc/0x1c8
 bus_for_each_dev+0xf4/0x168
 driver_attach+0x3c/0x50
 bus_add_driver+0x238/0x2e8
 driver_register+0xc8/0x1e8
 __platform_driver_register+0x88/0x98
 meson8b_dwmac_driver_init+0x28/0x1000 [dwmac_meson8b]
 do_one_initcall+0xa8/0x328
 do_init_module+0xe8/0x368
 load_module+0x3300/0x36b0
 __do_sys_finit_module+0x120/0x1a8
 __arm64_sys_finit_module+0x4c/0x60
 el0_svc_common.constprop.2+0xe4/0x268
 do_el0_svc+0x98/0xa8
 el0_svc+0x24/0x68
 el0_sync_handler+0x12c/0x318
 el0_sync+0x158/0x180

The buggy address belongs to the variable:
 div_table.63646+0x34/0xfffffffffffffa40 [dwmac_meson8b]

Memory state around the buggy address:
 ffffa00009061480: fa fa fa fa 00 00 00 01 fa fa fa fa 00 00 00 00
 ffffa00009061500: 05 fa fa fa fa fa fa fa 00 04 fa fa fa fa fa fa
>ffffa00009061580: 00 03 fa fa fa fa fa fa 00 00 00 00 00 00 fa fa
                                                             ^
 ffffa00009061600: fa fa fa fa 00 01 fa fa fa fa fa fa 01 fa fa fa
 ffffa00009061680: fa fa fa fa 00 01 fa fa fa fa fa fa 04 fa fa fa
==================================================================

Digging into this indeed shows that the clock divider array is
lacking a final fence, and that the clock subsystems goes in the
weeds. Oh well.

Let's add the empty structure that indicates the end of the array.

Fixes: bd6f4854 ("net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b6f61189 ("ipv6: restrict IPV6_ADDRFORM operation") fixed a
problem found by syzbot an unfortunate logic error meant that it
also broke IPV6_ADDRFORM.

Rearrange the checks so that the earlier test is just one of the series
of checks made before moving the socket from IPv6 to IPv4.

Fixes: b6f61189 ("ipv6: restrict IPV6_ADDRFORM operation")
Signed-off-by: John Haxby <john.haxby@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

In the function bcm_sysport_probe(), when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant message
here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot wrote:
| =============================
| WARNING: suspicious RCU usage
| 5.7.0-rc1+ #45 Not tainted
| -----------------------------
| net/openvswitch/conntrack.c:1898 RCU-list traversed in non-reader section!!
|
| other info that might help us debug this:
| rcu_scheduler_active = 2, debug_locks = 1
| ...
|
| stack backtrace:
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-0-ga698c8995f-prebuilt.qemu.org 04/01/2014
| Workqueue: netns cleanup_net
| Call Trace:
| ...
| ovs_ct_exit
| ovs_exit_net
| ops_exit_list.isra.7
| cleanup_net
| process_one_work
| worker_thread

To avoid that warning, invoke the ovs_ct_exit under ovs_lock and add
lockdep_ovsl_is_held as optional lockdep expression.

Link: https://lore.kernel.org/lkml/000000000000e642a905a0cbee6e@google.com
Fixes: 11efd5cb ("openvswitch: Support conntrack zone limit")
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: Yi-Hung Wei <yihung.wei@gmail.com>
Reported-by: syzbot+7ef50afd3a211f879112@syzkaller.appspotmail.com
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

A case of warning was reported by syzbot.

------------[ cut here ]------------
WARNING: CPU: 0 PID: 19934 at net/netfilter/nf_nat_core.c:1106
nf_nat_unregister_fn+0x532/0x5c0 net/netfilter/nf_nat_core.c:1106
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 19934 Comm: syz-executor.5 Not tainted 5.6.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x188/0x20d lib/dump_stack.c:118
 panic+0x2e3/0x75c kernel/panic.c:221
 __warn.cold+0x2f/0x35 kernel/panic.c:582
 report_bug+0x27b/0x2f0 lib/bug.c:195
 fixup_bug arch/x86/kernel/traps.c:175 [inline]
 fixup_bug arch/x86/kernel/traps.c:170 [inline]
 do_error_trap+0x12b/0x220 arch/x86/kernel/traps.c:267
 do_invalid_op+0x32/0x40 arch/x86/kernel/traps.c:286
 invalid_op+0x23/0x30 arch/x86/entry/entry_64.S:1027
RIP: 0010:nf_nat_unregister_fn+0x532/0x5c0 net/netfilter/nf_nat_core.c:1106
Code: ff df 48 c1 ea 03 80 3c 02 00 75 75 48 8b 44 24 10 4c 89 ef 48 c7 00 00 00 00 00 e8 e8 f8 53 fb e9 4d fe ff ff e8 ee 9c 16 fb <0f> 0b e9 41 fe ff ff e8 e2 45 54 fb e9 b5 fd ff ff 48 8b 7c 24 20
RSP: 0018:ffffc90005487208 EFLAGS: 00010246
RAX: 0000000000040000 RBX: 0000000000000004 RCX: ffffc9001444a000
RDX: 0000000000040000 RSI: ffffffff865c94a2 RDI: 0000000000000005
RBP: ffff88808b5cf000 R08: ffff8880a2620140 R09: fffffbfff14bcd79
R10: ffffc90005487208 R11: fffffbfff14bcd78 R12: 0000000000000000
R13: 0000000000000001 R14: 0000000000000001 R15: 0000000000000000
 nf_nat_ipv6_unregister_fn net/netfilter/nf_nat_proto.c:1017 [inline]
 nf_nat_inet_register_fn net/netfilter/nf_nat_proto.c:1038 [inline]
 nf_nat_inet_register_fn+0xfc/0x140 net/netfilter/nf_nat_proto.c:1023
 nf_tables_register_hook net/netfilter/nf_tables_api.c:224 [inline]
 nf_tables_addchain.constprop.0+0x82e/0x13c0 net/netfilter/nf_tables_api.c:1981
 nf_tables_newchain+0xf68/0x16a0 net/netfilter/nf_tables_api.c:2235
 nfnetlink_rcv_batch+0x83a/0x1610 net/netfilter/nfnetlink.c:433
 nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:543 [inline]
 nfnetlink_rcv+0x3af/0x420 net/netfilter/nfnetlink.c:561
 netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
 netlink_unicast+0x537/0x740 net/netlink/af_netlink.c:1329
 netlink_sendmsg+0x882/0xe10 net/netlink/af_netlink.c:1918
 sock_sendmsg_nosec net/socket.c:652 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:672
 ____sys_sendmsg+0x6bf/0x7e0 net/socket.c:2362
 ___sys_sendmsg+0x100/0x170 net/socket.c:2416
 __sys_sendmsg+0xec/0x1b0 net/socket.c:2449
 do_syscall_64+0xf6/0x7d0 arch/x86/entry/common.c:295
 entry_SYSCALL_64_after_hwframe+0x49/0xb3

and to quiesce it, unregister NFPROTO_IPV6 hook instead of NFPROTO_INET
in case of failing to register NFPROTO_IPV4 hook.
Reported-by: syzbot <syzbot+33e06702fd6cffc24c40@syzkaller.appspotmail.com>
Fixes: d164385e ("netfilter: nat: add inet family nat support")
Cc: Florian Westphal <fw@strlen.de>
Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

TCP stack is dumb in how it cooks its output packets.

Depending on MAX_HEADER value, we might chose a bad ending point
for the headers.

If we align the end of TCP headers to cache line boundary, we
make sure to always use the smallest number of cache lines,
which always help.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Westphal says:

====================
mptcp: fix 'attempt to release socket in state...' splats

These two patches fix error handling corner-cases where
inet_sock_destruct gets called for a mptcp_sk that is not in TCP_CLOSE
state.  This results in unwanted error printks from the network stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to set sk_state to CLOSED, else we will get following:

IPv4: Attempt to release TCP socket in state 3 00000000b95f109e
IPv4: Attempt to release TCP socket in state 10 00000000b95f109e

First one is from inet_sock_destruct(), second one from
mptcp_sk_clone failure handling.  Setting sk_state to CLOSED isn't
enough, we also need to orphan sk so it has DEAD flag set.
Otherwise, a very similar warning is printed from inet_sock_destruct().
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following snippet (replicated from syzkaller reproducer) generates
warning: "IPv4: Attempt to release TCP socket in state 1".

int main(void) {
 struct sockaddr_in sin1 = { .sin_family = 2, .sin_port = 0x4e20,
                             .sin_addr.s_addr = 0x010000e0, };
 struct sockaddr_in sin2 = { .sin_family = 2,
	                     .sin_addr.s_addr = 0x0100007f, };
 struct sockaddr_in sin3 = { .sin_family = 2, .sin_port = 0x4e20,
	                     .sin_addr.s_addr = 0x0100007f, };
 int r0 = socket(0x2, 0x1, 0x106);
 int r1 = socket(0x2, 0x1, 0x106);

 bind(r1, (void *)&sin1, sizeof(sin1));
 connect(r1, (void *)&sin2, sizeof(sin2));
 listen(r1, 3);
 return connect(r0, (void *)&sin3, 0x4d);
}

Reason is that the newly generated mptcp socket is closed via the ulp
release of the tcp listener socket when its accept backlog gets purged.

To fix this, delay setting the ESTABLISHED state until after userspace
calls accept and via mptcp specific destructor.

Fixes: 58b09919 ("mptcp: create msk early")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/9Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 9ecc2d86 ("net/mlx4_en: add xdp forwarding and data write support")
brought another indirect call in fast path.

Use INDIRECT_CALL_2() helper to avoid the cost of the indirect call
when/if CONFIG_RETPOLINE=y
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes it impossible that cmpri or cmpre values are set to the
value 16 which is not possible, because these are 4 bit values. We
currently run in an overflow when assigning the value 16 to it.

According to the standard a value of 16 can be interpreted as a full
elided address which isn't possible to set as compression value. A reason
why this cannot be set is that the current ipv6 header destination address
should never show up inside the segments of the rpl header. In this case we
run in a overflow and the address will have no compression at all. Means
cmpri or compre is set to 0.

As we handle cmpri and cmpre sometimes as unsigned char or 4 bit value
inside the rpl header the current behaviour ends in an invalid header
format. This patch simple use the best compression method if we ever run
into the case that the destination address is showed up inside the rpl
segments. We avoid the overflow handling and the rpl header is still valid,
even when we have the destination address inside the rpl segments.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In fine adjustement mode, which is the current default, the sub-second
    increment register is the number of nanoseconds that will be added to
    the clock when the accumulator overflows. At each clock cycle, the
    value of the addend register is added to the accumulator.
    Currently, we use 20ns = 1e09ns / 50MHz as this value whatever the
    frequency of the ptp clock actually is.
    The adjustment is then done on the addend register, only incrementing
    every X clock cycles X being the ratio between 50MHz and ptp_clock_rate
    (addend = 2^32 * 50MHz/ptp_clock_rate).
    This causes the following issues :
    - In case the frequency of the ptp clock is inferior or equal to 50MHz,
      the addend value calculation will overflow and the default
      addend value will be set to 0, causing the clock to not work at
      all. (For instance, for ptp_clock_rate = 50MHz, addend = 2^32).
    - The resolution of the timestamping clock is limited to 20ns while it
      is not needed, thus limiting the accuracy of the timestamping to
      20ns.

    Fix this by setting sub-second increment to 2e09ns / ptp_clock_rate.
    It will allow to reach the minimum possible frequency for
    ptp_clk_ref, which is 5MHz for GMII 1000Mps Full-Duplex by setting the
    sub-second-increment to a higher value. For instance, for 25MHz, it
    gives ssinc = 80ns and default_addend = 2^31.
    It will also allow to use a lower value for sub-second-increment, thus
    improving the timestamping accuracy with frequencies higher than
    100MHz, for instance, for 200MHz, ssinc = 10ns and default_addend =
    2^31.

v1->v2:
 - Remove modifications to the calculation of default addend, which broke
 compatibility with clock frequencies for which 2000000000 / ptp_clk_freq
 is not an integer.
 - Modify description according to discussions.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are 2 registers to write to enable a ptp ref clock coming from the
fpga.
One that enables the usage of the clock from the fpga for emac0 and emac1
as a ptp ref clock, and the other to allow signals from the fpga to reach
emac0 and emac1.
Currently, if the dwmac-socfpga has phymode set to PHY_INTERFACE_MODE_MII,
PHY_INTERFACE_MODE_GMII, or PHY_INTERFACE_MODE_SGMII, both registers will
be written and the ptp ref clock will be set as coming from the fpga.
Separate the 2 register writes to only enable signals from the fpga to
reach emac0 or emac1 when ptp ref clock is not coming from the fpga.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

i2400mu_bus_bm_wait_for_ack() invokes usb_get_urb(), which increases the
refcount of the "notif_urb".

When i2400mu_bus_bm_wait_for_ack() returns, local variable "notif_urb"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.

The issue happens in all paths of i2400mu_bus_bm_wait_for_ack(), which
forget to decrease the refcnt increased by usb_get_urb(), causing a
refcnt leak.

Fix this issue by calling usb_put_urb() before the
i2400mu_bus_bm_wait_for_ack() returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc_rcv() invokes tipc_node_find() twice, which returns a reference of
the specified tipc_node object to "n" with increased refcnt.

When tipc_rcv() returns or a new object is assigned to "n", the original
local reference of "n" becomes invalid, so the refcount should be
decreased to keep refcount balanced.

The issue happens in some paths of tipc_rcv(), which forget to decrease
the refcnt increased by tipc_node_find() and will cause a refcnt leak.

Fix this issue by calling tipc_node_put() before the original object
pointed by "n" becomes invalid.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc_crypto_rcv() invokes tipc_aead_get(), which returns a reference of
the tipc_aead object to "aead" with increased refcnt.

When tipc_crypto_rcv() returns, the original local reference of "aead"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.

The issue happens in one error path of tipc_crypto_rcv(). When TIPC
message decryption status is EINPROGRESS or EBUSY, the function forgets
to decrease the refcnt increased by tipc_aead_get() and causes a refcnt
leak.

Fix this issue by calling tipc_aead_put() on the error path when TIPC
message decryption status is EINPROGRESS or EBUSY.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nr_add_node() invokes nr_neigh_get_dev(), which returns a local
reference of the nr_neigh object to "nr_neigh" with increased refcnt.

When nr_add_node() returns, "nr_neigh" becomes invalid, so the refcount
should be decreased to keep refcount balanced.

The issue happens in one normal path of nr_add_node(), which forgets to
decrease the refcnt increased by nr_neigh_get_dev() and causes a refcnt
leak. It should decrease the refcnt before the function returns like
other normal paths do.

Fix this issue by calling nr_neigh_put() before the nr_add_node()
returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'tag-chrome-platform-fixes-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux

Pull chrome-platform fixes from Benson Leung:
 "Two small fixes for cros_ec_sensorhub_ring.c, addressing issues
  introduced in the cros_ec_sensorhub FIFO support commit"

* tag 'tag-chrome-platform-fixes-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
  platform/chrome: cros_ec_sensorhub: Add missing '\n' in log messages
  platform/chrome: cros_ec_sensorhub: Off by one in cros_sensorhub_send_sample()

Pull networking fixes from David Miller:

 1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel.

 2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet.

 3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing.

 4) Adjust icmp6 message source address selection when routes have a
    preferred source address set, from Tim Stallard.

 5) Be sure to validate HSR protocol version when creating new links,
    from Taehee Yoo.

 6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in
    non-initial namespaces, from Michael Weiß.

 7) Missing release firmware call in mlx5, from Eran Ben Elisha.

 8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from
    Taehee Yoo.

 9) Fix pause frame negotiation in marvell phy driver, from Clemens
    Gruber.

10) Record RX queue early enough in tun packet paths such that XDP
    programs will see the correct RX queue index, from Gilberto Bertin.

11) Fix double unlock in mptcp, from Florian Westphal.

12) Fix offset overflow in ARM bpf JIT, from Luke Nelson.

13) marvell10g needs to soft reset PHY when coming out of low power
    mode, from Russell King.

14) Fix MTU setting regression in stmmac for some chip types, from
    Florian Fainelli.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
  amd-xgbe: Use __napi_schedule() in BH context
  mISDN: make dmril and dmrim static
  net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes
  net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode
  tipc: fix incorrect increasing of link window
  Documentation: Fix tcp_challenge_ack_limit default value
  net: tulip: make early_486_chipsets static
  dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400
  ipv6: remove redundant assignment to variable err
  net/rds: Use ERR_PTR for rds_message_alloc_sgs()
  net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge
  selftests/bpf: Check for correct program attach/detach in xdp_attach test
  libbpf: Fix type of old_fd in bpf_xdp_set_link_opts
  libbpf: Always specify expected_attach_type on program load if supported
  xsk: Add missing check on user supplied headroom size
  mac80211: fix channel switch trigger from unknown mesh peer
  mac80211: fix race in ieee80211_register_hw()
  net: marvell10g: soft-reset the PHY when coming out of low power
  net: marvell10g: report firmware version
  net/cxgb4: Check the return from t4_query_params properly
  ...

The driver uses __napi_schedule_irqoff() which is fine as long as it is
invoked with disabled interrupts by everybody. Since the commit
mentioned below the driver may invoke xgbe_isr_task() in tasklet/softirq
context. This may lead to list corruption if another driver uses
__napi_schedule_irqoff() in IRQ context.

Use __napi_schedule() which safe to use from IRQ and softirq context.

Fixes: 85b85c85 ("amd-xgbe: Re-issue interrupt if interrupt status not cleared")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>