- 13 Feb, 2015 40 commits
-
-
Tvrtko Ursulin authored
And skl only works in execlist mode, not in legacy ring submission. Therefore remove dead code. Signed-off-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Daniel Vetter authored
Just a little demo really. We probably need to introduce skl specific functions for a lot of the format validation stuff, or at least helpers. Specifically I think intel_framebuffer_init and intel_fb_align_height must be adjusted to have an i915_ and a skl_ variant. And only shared code should be converted to fb modifiers, platform code (like the plane config readout can keep on using old tiling_mode defines to avoid some churn). Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by:
Daniel Vetter <daniel.vetter@intel.com>
-
Daniel Vetter authored
With this we can treat the fb format modifier completely independently from the fencing mode in obj->tiling_mode in the initial plane code. Which means new tiling modes without any gtt fence are now fully support in the core i915 driver code. v2: Also add pixel_format while at it, we need this to compute the height for the new tiling formats. Reviewed-by:
-
Daniel Vetter authored
No functional changes yet since intel_framebuffer_init would have fixed this up for us. But this is prep work to be able to handle new tiling layouts in the initial plane config code. Follow-up patches will start to make use of this and switch over to fb modifiers where needed. Reviewed-by:
-
Tvrtko Ursulin authored
Signed-off-by:
-
Daniel Vetter authored
Currently we don't support anything but X tiled. And for an easier transition it makes a lot of sense to just keep requiring that X tiled is properly fenced. Which means we need to do absolutely nothing in old code to support fb modifiers, yay! v2: Fix the Y tiling check, noticed by Tvrtko. v3: Catch Y-tiled fb for legacy addfb again (Tvrtko) and explain why we want X tiling to match in the comment. Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by:
-
Tvrtko Ursulin authored
To be used from the new addfb2 extension. v2: - Drop Intel-specific untiled modfier. - Move to drm_fourcc.h. - Document layouts a bit and denote them as platform-specific and not useable for cross-driver sharing. - Add Y-tiling for completeness. - Drop special docstring markers to avoid confusing kerneldoc. v3: Give Y-tiling a unique idea, noticed by Tvrtko. Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v1) Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by:
-
Damien Lespiau authored
v2: Reorder defines (Ben) v3: More bikesheds, this time re-ordering comments! (Chris) Reviewed-by:
Ben Widawsky <ben@bwidawsk.net> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Damien Lespiau <damien.lespiau@intel.com> [danvet: Resolve conflict.] Signed-off-by:
-
Damien Lespiau authored
When enabling new platforms, we may not have any W/A to apply, especially that, now, a bunch of them have to be done from the ring. Signed-off-by:
-
Paulo Zanoni authored
Since the mapping from CRTCs to planes is fixed, looking at the CRTC is essentially the same as looking at the plane. Also, the next patches wil start using the frontbuffer_bits macros, and they take the pipe as the parameter instead of the plane, and this could differ on gens 2 and 3. Another nice thing is that we don't risk accidentally initializing things to PLANE_A if we don't set the value before it is used for the first time. But this shouldn't be a problem with the current code. V2: Rebase. Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> (v1) Signed-off-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by:
-
Paulo Zanoni authored
This may save a few picoseconds on !HAS_FBC platforms. And it also satisfies my OCD. Reviewed-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
-
Paulo Zanoni authored
.. because it would be a waste of time, so move the place where the check is done. Also, with this we won't risk printing "more than one pipe active, disabling compression" or "no output, disabling" when FBC is actually disabled. This patch also represents a small behavior difference when using i915.powersave=0: it is now exactly the same as i915.enable_fbc=0 on this part of the code. V2: Rebase. Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> (v1) Signed-off-by:
-
Nick Hoath authored
Add: WaEnableForceRestoreInCtxtDescForVCS v2: Add stepping check. v3: Fixed stepping check direction. Cleaned up indentation. Signed-off-by:
Nick Hoath <nicholas.hoath@intel.com> Reviewed-by:
-
Nick Hoath authored
Fixed the stepping check on WaDisableDgMirrorFixInHalfSliceChicken5 to be for the correct SOC (Skylake) Signed-off-by:
-
Rob Clark authored
In DRM/KMS we are lacking a good way to deal with tiled/compressed formats. Especially in the case of dmabuf/prime buffer sharing, where we cannot always rely on under-the-hood flags passed to driver specific gem-create ioctl to pass around these extra flags. The proposal is to add a per-plane format modifier. This allows to, if necessary, use different tiling patters for sub-sampled planes, etc. The format modifiers are added at the end of the ioctl struct, so for legacy userspace it will be zero padded. v1: original v1.5: increase modifier to 64b v2: Incorporate review comments from the big thread, plus a few more. - Add a getcap so that userspace doesn't have to jump through hoops. - Allow modifiers only when a flag is set. That way drivers know when they're dealing with old userspace and need to fish out e.g. tiling from other information. - After rolling out checks for ->modifier to all drivers I've decided that this is way too fragile and needs an explicit opt-in flag. So do that instead. - Add a define (just for documentation really) for the "NONE" modifier. Imo we don't need to add mask #defines since drivers really should only do exact matches against values defined with fourcc_mod_code. - Drop the Samsung tiling modifier on Rob's request since he's not yet sure whether that one is accurate. v3: - Also add a new ->modifier[] array to struct drm_framebuffer and fill it in drm_helper_mode_fill_fb_struct. Requested by Tvrkto Uruslin. - Remove TODO in comment and add code comment that modifiers should be properly documented, requested by Rob. Cc: Rob Clark <robdclark@gmail.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Daniel Stone <daniel@fooishbar.org> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Michel Dänzer <michel@daenzer.net> Signed-off-by: Rob Clark <robdclark@gmail.com> (v1.5) Reviewed-by:
Rob Clark <robdclark@gmail.com> Reviewed-by:
Daniel Stone <daniels@collabora.com> Acked-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Ben Widawsky authored
Signed-off-by:
Michel Thierry <michel.thierry@intel.com> Reviewed-by:
Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by:
-
Ben Widawsky authored
The current code will both potentially print a WARN, and setup part of the PPGTT structure. Neither of these harm the current code, it is simply for clarity, and to perhaps prevent later bugs, or weird debug messages. Signed-off-by:
-
Ben Widawsky authored
In gen8, 32b PPGTT has always had one "pdp" (it doesn't actually have one, but it resembles having one). The #define was confusing as is, and using "PDPE" is a much better description. sed -i 's/GEN8_LEGACY_PDPS/GEN8_LEGACY_PDPES/' drivers/gpu/drm/i915/*.[ch] It also matches the x86 pagetable terminology: PTE = Page Table Entry - pagetable level 1 page PDE = Page Directory Entry - pagetable level 2 page PDPE = Page Directory Pointer Entry - pagetable level 3 page And in the near future (for 48b addressing): PML4E = Page Map Level 4 Entry v2: Expanded information about Page Directory/Table nomenclature. Cc: Daniel Vetter <daniel@ffwll.ch> CC: Dave Gordon <david.s.gordon@intel.com> Signed-off-by:
-
Ben Widawsky authored
Signed-off-by:
-
Hoath, Nicholas authored
v2: Don't add WaHdcDisableFetchWhenMasked. Add stepping check for WaForceEnableNonCoherent Signed-off-by:
-
Hoath, Nicholas authored
Move Wa4x4STCOptimizationDisable to gen9_init_workarounds v2: rebase Signed-off-by:
-
Nick Hoath authored
Move WaEnableYV12BugFixInHalfSliceChicken7 to gen9_init_workarounds v2: Add stepping check. Signed-off-by:
-
Hoath, Nicholas authored
v2: Add stepping check for WaDisableSDEUnitClockGating. Signed-off-by:
-
Nick Hoath authored
This one doesn't have one of these nice cryptic names unfortunately. v2: Added missing register bitmap Signed-off-by:
-
Nick Hoath authored
Move WaDisableDgMirrorFixInHalfSliceChicken5 to gen9_init_workarounds v2: Added stepping check v3: Removed unused register bitmap Signed-off-by:
-
Hoath, Nicholas authored
v2: Dont add WaDisableThreadStallDopClockGating as not SKL WA. (Found by Damien Lespiau) Signed-off-by:
-
Hoath, Nicholas authored
Add Skylake stepping Revision IDs definitions. v1: Use existing revision id. Signed-off-by:
-
Hoath, Nicholas authored
Add framework for gen 9 HW WAs v1: Changed SOC specific WA function to gen 9 common function (Req: Damien Lespiau) Signed-off-by:
-
Damien Lespiau authored
We don't want to end up in a state where we track that the pipe has its primary plane enabled when primary plane registers are programmed with values that look possible but the plane actually disabled. Refuse to read out the fb state when the primary plane isn't enabled. Suggested-by:
Matt Roper <matthew.d.roper@intel.com> Signed-off-by:
-
Damien Lespiau authored
Right now, we get a warning when taking over the firmware fb: [drm:drm_atomic_plane_check] FB set but no CRTC with the following backtrace: [<ffffffffa010339d>] drm_atomic_check_only+0x35d/0x510 [drm] [<ffffffffa0103567>] drm_atomic_commit+0x17/0x60 [drm] [<ffffffffa00a6ccd>] drm_atomic_helper_plane_set_property+0x8d/0xd0 [drm_kms_helper] [<ffffffffa00f1fed>] drm_mode_plane_set_obj_prop+0x2d/0x90 [drm] [<ffffffffa00a8a1b>] restore_fbdev_mode+0x6b/0xf0 [drm_kms_helper] [<ffffffffa00aa969>] drm_fb_helper_restore_fbdev_mode_unlocked+0x29/0x80 [drm_kms_helper] [<ffffffffa00aa9e2>] drm_fb_helper_set_par+0x22/0x50 [drm_kms_helper] [<ffffffffa050a71a>] intel_fbdev_set_par+0x1a/0x60 [i915] [<ffffffff813ad444>] fbcon_init+0x4f4/0x580 That's because we update the plane state with the fb from the firmware, but we never associate the plane to that CRTC. We don't quite have the full DRM take over from HW state just yet, so fake enough of the plane atomic state to pass the checks. v2: Fix the state on which we set the CRTC in the case we're sharing the initial fb with another pipe. (Matt) Signed-off-by: -
Damien Lespiau authored
At the moment we use crtc->base.primary->fb to hold the initial framebuffer allocation, disregarding if it's valid or not. This lead to believe we were actually updating the fb at this point, but it's not true and we haven't even called drm_framebuffer_init() on this fb. Instead, let's store the state in struct intel_initial_plane_config until we know we can reuse that framebuffer. Signed-off-by:
-
Damien Lespiau authored
Tvrtko noticed a new warning on boot: WARNING: CPU: 1 PID: 353 at include/linux/kref.h:47 drm_framebuffer_reference+0x6c/0x80 [drm]() Call Trace: [<ffffffff8161f10c>] dump_stack+0x4f/0x7b [<ffffffff81052caa>] warn_slowpath_common+0xaa/0xd0 [<ffffffff81052d8a>] warn_slowpath_null+0x1a/0x20 [<ffffffffa00d035c>] drm_framebuffer_reference+0x6c/0x80 [drm] [<ffffffffa01c0df7>] update_state_fb.isra.54+0x47/0x50 [i915] [<ffffffffa01ccd5c>] skylake_get_initial_plane_config+0x93c/0x950 [i915] [<ffffffffa01e8721>] intel_modeset_init+0x1551/0x17c0 [i915] [<ffffffffa02476e0>] i915_driver_load+0xed0/0x11e0 [i915] [<ffffffff81627aa1>] ? _raw_spin_unlock_irqrestore+0x51/0x70 [<ffffffffa00ca8b7>] drm_dev_register+0x77/0x110 [drm] [<ffffffffa00cda3b>] drm_get_pci_dev+0x11b/0x1f0 [drm] [<ffffffff81098e3d>] ? trace_hardirqs_on+0xd/0x10 [<ffffffff81627aa1>] ? _raw_spin_unlock_irqrestore+0x51/0x70 [<ffffffffa0145276>] i915_pci_probe+0x56/0x60 [i915] [<ffffffff813ad59c>] pci_device_probe+0x7c/0x100 [<ffffffff81466aad>] driver_probe_device+0x16d/0x380 We cannot take a reference at this point, not before intel_framebuffer_init() and the underlying drm_framebuffer_init(). Introduced in: commit 706dc7b549175e47f23e913b7f1e52874a7d0f56 Author: Matt Roper <matthew.d.roper@intel.com> Date: Tue Feb 3 13:10:04 2015 -0800 drm/i915: Ensure plane->state->fb stays in sync with plane->fb v2: Don't move update_state_fb(). It was moved around because I originally put update_state_fb() in intel_alloc_plane_obj() before finding a better place. (Matt) Reviewed-by: -
Damien Lespiau authored
The code look slightly better this way and will ease the next commit, changing where we take the fb pointer from. Signed-off-by:
-
Damien Lespiau authored
update_state_fb() at the end of intel_find_plane_obj() is misleading as it leads us to believe the update is done for all code path. A successful call to intel_alloc_plane_obj() will return and update_state_fb() is then only needed when we share a fb from another CRTC. Put the update() function there then. Signed-off-by:
-
Jani Nikula authored
The check for previously reserved stolen space size for FBC in i915_gem_stolen_setup_compression() did not take the compression threshold into account. Fix this by storing and comparing to uncompressed size instead. The bug has been introduced in commit 5e59f717 Author: Ben Widawsky <benjamin.widawsky@intel.com> Date: Mon Jun 30 10:41:24 2014 -0700 drm/i915: Try harder to get FBC Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88975Suggested-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Ben Widawsky <benjamin.widawsky@intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Reviewed-by:
-
Damien Lespiau authored
v2: leave intel_skylake_info alone (Rodrigo, Daniel) Signed-off-by:
-
Damien Lespiau authored
We need to have a separate GT3 struct intel_device_info to declare they have a second VCS. Let's start by splitting the PCI ids per-GT. Signed-off-by:
-
Satheeshakrishna M authored
This patch implements core logic of SKL display power well. v2: Addressed Imre's comments - Added respective DDIs under power well #1 and #2 - Simplified repetitive code in power well programming v3: Implemented Imre's comments - Further simplified power well programming - Made sure that PW 1 is enabled prior to PW 2 v4: Fix minor conflict with the the cherryview support (Damien) v5: Add the PLL power domain to the always on power well (Damien) v6: Disable BIOS power well (Imre) Use power well data for comparison (Imre) Put the PLL power domain into PW1 as its needed for CDCLK (Satheesh, Damien) v7: Addressed Imre's comments - Lowered the time out to 1ms - Added parantheses in macro - Moved debug message and fixed wait_for interval v8: - Add a WARN() when swiching on an unknown power well (Imre, done by Damien) - Whitespace fixes (spaces instead of tabs) (Damien) v9: (Imre, done by Damien) - Merge the register definitions with this patch - Merge the MISC IO power well in this patch v10: (Imre, done by Damien) - Define the Misc I/O power domains to be the power well 1 ones as Misc I/O needs to be enabled with PW1 - Added Transcoder A and VGA domains to PW 2 - Remove the MISC_IO power domains as well in the the always on domains definition - Move Misc I/O power well at the top of the power well list so it's turned on right after PW1. Reviewed-by:Imre Deak <imre.deak@intel.com> Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3,v6,v7) Signed-off-by:
-
Matt Roper authored
plane->state->fb and plane->fb should always reference the same FB so that atomic and legacy codepaths have the same view of display state. In commit commit db068420560511de80ac59222644f2bdf278c3d5 Author: Matt Roper <matthew.d.roper@intel.com> Date: Fri Jan 30 16:22:36 2015 -0800 drm/i915: Keep plane->state updated on pageflip we already fixed one case where these two pointers could get out of sync. However it turns out there are a few other places (mainly dealing with initial FB setup at boot) that directly set plane->fb and neglect to update plane->state->fb. If we never do a successful update through the atomic pipeline, the RmFB cleanup code will look at the plane->state->fb pointer, which has never actually been set to a legitimate value, and try to clean it up, leading to BUG's. Add a quick helper function to synchronize plane->state->fb with plane->fb (and update reference counts accordingly) and call it everywhere the driver tries to manually set plane->fb outside of the atomic pipeline. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88909Signed-off-by: -
Damien Lespiau authored
We already track this in the intel_info struct. Signed-off-by:
-
