Implement basic WoW functionalities such as magic-packet, disconnect
and pattern. The logic is very similar to ath10k.

When WoW is configured, ath11k_core_suspend and ath11k_core_resume
are skipped as WoW configuration and hif suspend/resume are done in
ath11k_wow_op_suspend() and ath11k_wow_op_resume().

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-2-git-send-email-quic_cjhuang@quicinc.com

Merge tag 'linux-can-next-for-5.18-20220313' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

linux-can-next-for-5.18-20220313

Marc Kleine-Budde says:

====================
pull-request: can-next 2022-03-13

this is a pull request of 13 patches for net-next/master.

The 1st patch is by me and fixes the freeing of a skb in the vxcan
driver (initially added in this net-next window).

The remaining 12 patches are also by me and target the mcp251xfd
driver. The first patch fixes a printf modifier (initially added in
this net-next window). The remaining patches add ethtool based ring
and RX/TX IRQ coalescing support to the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch increases the number of RX-FIFOs to 3 and the max TX-FIFO
depth to 16. This leads to the following default ring configuration.

CAN-2.0 mode:

| FIFO setup: TEF:         0x400:  8*12 bytes =   96 bytes
| FIFO setup: RX-0: FIFO 1/0x460: 32*20 bytes =  640 bytes
| FIFO setup: RX-1: FIFO 2/0x6e0: 32*20 bytes =  640 bytes
| FIFO setup: RX-2: FIFO 3/0x960: 16*20 bytes =  320 bytes
| FIFO setup: TX:   FIFO 4/0xaa0:  8*16 bytes =  128 bytes
| FIFO setup: free:                              224 bytes

CAN-FD mode:

| FIFO setup: TEF:         0x400:  4*12 bytes =   48 bytes
| FIFO setup: RX-0: FIFO 1/0x430: 16*76 bytes = 1216 bytes
| FIFO setup: RX-1: FIFO 2/0x8f0:  4*76 bytes =  304 bytes
| FIFO setup: TX:   FIFO 3/0xa20:  4*72 bytes =  288 bytes
| FIFO setup: free:                              192 bytes

With the previously added ethtool ring configuration support the RAM
on the chip can now be runtime configured between RX and TX buffers.

Link: https://lore.kernel.org/20220313083640.501791-13-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds support ethtool based configuration for the TX IRQ
coalescing added in the previous patch.

Link: https://lore.kernel.org/20220313083640.501791-12-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds TX IRQ coalescing support to the driver.

The implemented algorithm is similar to the RX IRQ coalescing support
added in the previous patch.

Link: https://lore.kernel.org/20220313083640.501791-11-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds support ethtool based configuration for the RX IRQ
coalescing added in the previous patch.

Link: https://lore.kernel.org/20220313083640.501791-10-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds RX IRQ coalescing support to the driver.

The mcp251xfd chip doesn't support proper hardware based coalescing,
so this patch tries to implemented it in software. The RX-FIFO offers
a "FIFO not empty" interrupt, which is used if no coalescing is
active.

With activated RX IRQ coalescing the "FIFO not empty" interrupt is
disabled in the RX IRQ handler and the "FIFO half full" or "FIFO full
interrupt" (depending on RX max coalesced frames IRQ) is used instead.
To avoid RX CAN frame starvation a hrtimer is setup with RX coalesce
usecs IRQ,on timer expiration the "FIFO not empty" is enabled again.

Support for ethtool configuration is added in the next patch.

Link: https://lore.kernel.org/20220313083640.501791-9-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds runtime configurable RX and TX ring parameters via
ethtool to the driver.

Link: https://lore.kernel.org/20220313083640.501791-8-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

So far the configuration of the hardware FIFOs is hard coded and
depend only on the selected CAN mode (CAN-2.0 or CAN-FD).

This patch updates the macros describing the ring, FIFO and RAM layout
to prepare for the next patches that add support for runtime
configurable ring parameters via ethtool.

Link: https://lore.kernel.org/20220313083640.501791-7-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch prepares the driver for runtime configurable RX and TX ring
parameters. The actual runtime config support will be added in the
next patch.

Link: https://lore.kernel.org/20220313083640.501791-6-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds basic ethtool support (to query the current and
maximum ring parameters) to the driver.

Link: https://lore.kernel.org/20220313083640.501791-5-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds support for coalescing to the RAM layout calculation.

Link: https://lore.kernel.org/20220313083640.501791-4-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds a helper function to calculate the ring configuration
of the controller based on various constraints, like available RAM,
size of RX and TX objects, CAN-mode, number of FIFOs and FIFO depth.

Link: https://lore.kernel.org/20220313083640.501791-3-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In case of an erroneous ring configuration more RAM than available
might be used. Change the printf modifier to a signed int to properly
print this erroneous value.

Fixes: 83daa863 ("can: mcp251xfd: ring: update FIFO setup debug info")
Link: https://lore.kernel.org/20220313083640.501791-2-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the freeing of the "oskb", by using kfree_skb()
instead of kfree().

Fixes: 1574481b ("vxcan: remove sk reference in peer skb")
Link: https://lore.kernel.org/all/20220311123741.382618-1-mkl@pengutronix.de
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Tony Nguyen says:

====================
ice: GTP support in switchdev

Marcin Szycik says:

Add support for adding GTP-C and GTP-U filters in switchdev mode.

To create a filter for GTP, create a GTP-type netdev with ip tool, enable
hardware offload, add qdisc and add a filter in tc:

ip link add $GTP0 type gtp role <sgsn/ggsn> hsize <hsize>
ethtool -K $PF0 hw-tc-offload on
tc qdisc add dev $GTP0 ingress
tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
action mirred egress redirect dev $VF1_PR

By default, a filter for GTP-U will be added. To add a filter for GTP-C,
specify enc_dst_port = 2123, e.g.:

tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
enc_dst_port 2123 action mirred egress redirect dev $VF1_PR

Note: outer IPv6 offload is not supported yet.
Note: GTP-U with no payload offload is not supported yet.

ICE COMMS package is required to create a filter as it contains GTP
profiles.

Changes in iproute2 [1] are required to be able to add GTP netdev and use
GTP-specific options (QFI and PDU type).

[1] https://lore.kernel.org/netdev/20220211182902.11542-1-wojciech.drewek@intel.com/T
---
v2: Add more CC
v3: Fix mail thread, sorry for spam
v4: Add GTP echo response in gtp module
v5: Change patch order
v6: Add GTP echo request in gtp module
v7: Fix kernel-docs in ice
v8: Remove handling of GTP Echo Response
v9: Add sending of multicast message on GTP Echo Response, fix GTP-C dummy
    packet selection
v10: Rebase, fixed most 80 char line limits
v11: Rebase, collect Harald's Reviewed-by on patch 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In case external PHY is used, we need to take care of embedded PHY.
Since there are no methods to disable this PHY from the MAC side and
keeping RMII reference clock, we need to suspend it.

This patch will reduce electrical noise (PHY is continuing to send FLPs)
and power consumption by 0,22W.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

In most cases we use own mdio bus, there is no need to create and store
string for the PHY address.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

We already read chipid on probe. There is no need to read it on reset.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The only difference is the reset code, so remove not needed duplicates.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before adding yet another possibly contended atomic_long_t,
it is time to add per-cpu storage for existing ones:
 dev->tx_dropped, dev->rx_dropped, and dev->rx_nohandler

Because many devices do not have to increment such counters,
allocate the per-cpu storage on demand, so that dev_get_stats()
does not have to spend considerable time folding zero counters.

Note that some drivers have abused these counters which
were supposed to be only used by core networking stack.

v4: should use per_cpu_ptr() in dev_get_stats() (Jakub)
v3: added a READ_ONCE() in netdev_core_stats_alloc() (Paolo)
v2: add a missing include (reported by kernel test robot <lkp@intel.com>)
    Change in netdev_core_stats_alloc() (Jakub)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: jeffreyji <jeffreyji@google.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220311051420.2608812-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Simon Horman says:

====================
nfp: preliminary support for NFP-3800

This series is the first step to add support to the NFP driver for the
new NFP-3800 device. In this first series the goal is to clean
up small issues found while adding support for the new device, prepare
an abstraction of the differences between the already supported devices
and the new Kestrel device and add the new PCI ID.

* Patch 1/11 and 2/11 starts by removing some dead code and incorrect
  assumptions found while working Kestrel support. Patch 3/11, 4/11 and
  5/11 cleans up and prepares for adding the new PCI ID for Kestrel.
* Patches 6/11, 7/11, 8/11, 9/11, 10/11 adds, plumb and populates a device
   information structure to abstract the differences between the existed
   supported devices (NFP-4000, NFP-5000 and NFP-6000) and the
   new device (NFP3800).
* Finally patch 11/11 adds the new PCI ID for Kestrel.

More work is needed to drive the new NFP-3800 device after this first
batch of patches the foundation is prepared for the follow up work.

Thanks to the work of all those who contributed to this work.
====================

Link: https://lore.kernel.org/r/20220311104306.28357-1-simon.horman@corigine.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Enable binding the nfp driver to NFP3800 and NFP3803 devices.
The PCIE_SRAM offset is different for the NFP3800 device, which also
only supports a single explicit group.

Changes to Dirk's work:
* 48-bit dma addressing is not ready yet. Keep 40-bit dma addressing
for NFP3800.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

NFP3800 has slightly different queue controller range bounds.
Use the static chip data instead of defines.  This commit
still assumes unchanged descriptor format.  Later datapath
changes will allow adjusting for descriptor accounting.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The queue controller (QCP) is accessed based on a device specific
offset. The NFP3800 device also supports more queues.

Furthermore, the NFP3800 VFs also access the QCP differently to how the
NFP6000 VFs accesses it, though still indirectly. Fortunately, we can
remove the offset all together for both VF types. This is safe for
NFP6000 VFs since the offset was effectively a wrap around and only used
for convenience to have it set the same as the NFP6000 PF.

Use nfp_dev_info to store queue controller parameters.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation for new chips instead of defines use dev_info constants
to store DMA mask length.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

NFP3800 uses a different PCIe configuration to CPP expansion BAR offsets.
We don't need to differentiate between the NFP4000, NFP5000 and NFP6000
since they all use the same offsets.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation for supporting new chip add a driver data structure
which will hold per-chip-version information such as register
offsets.

Plumb it through to the relevant functions (nfpcore and nfp_net).
For now only a very simple member holding chip names is added,
following commits will add more.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Make sure the device ID tables are in ascending order.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The model number for NFP3800 and newer devices can be completely
derived from PluDevice register without subtracting 0x10.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The PCI_DEVICE_ID_NETRONOME_NFP6000_VF is available for use and
should be used instead of the PCI_DEVICE_NFP6000VF. Meanwhile,
PCI_DEVICE_NFP6000VF PCI ID is removed for not being used.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Multiple writes cause intermediate pointer values that do not
end on complete TX descriptors.

The QCP peripheral on the NFP provides a number of access
modes.  In some access modes, the maximum amount to add must
be restricted to a 6bit value.  The particular access mode
used by _nfp_qcp_ptr_add() has no such restrictions, so the
"< NFP_QCP_MAX_ADD" test is unnecessary.

Note that trying to add more that the configured ring size
in a single add will cause a QCP overflow, caught and handled
by the QCP peripheral.
Signed-off-by: Christo du Toit <christo.du.toit@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

NFP driver ABI contains a bit for ring prioritization which
was never implemented in the initially envisioned form.

Remove it, and open up the possibility of reclaiming for other uses.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The print function dev_err() is redundant because platform_get_irq()
already prints an error.

Eliminate the follow coccicheck warning:
./drivers/net/ethernet/8390/mcf8390.c:414:2-9: line 414 is redundant
because platform_get_irq() already prints an error
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220311001756.12234-1-yang.lee@linux.alibaba.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

netdev_name_node_alt_create() and netdev_name_node_alt_destroy()
are only called by rtnetlink, so no need for exports.
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220310223952.558779-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In function netvsc_process_raw_pkt for VM_PKT_DATA_USING_XFER_PAGES
case there is already a 'return' statement which results 'break'
as dead code
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1646933534-29493-1-git-send-email-ssengar@linux.microsoft.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Both functions are only used by core networking code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220310143229.895319-1-hch@lst.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In review for commit 8ee7ec48 ("net: ipa: embed interconnect
array in the power structure"), Jakub Kicinski suggested that a
follow-up patch use struct_size() when computing the size of the
IPA power structure, which ends with a flexible array member.

Do that.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20220311162423.872645-1-elder@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Johannes Berg says:

====================
brcmfmac
 * add BCM43454/6 support

rtw89
 * add support for 160 MHz channels and 6 GHz band
 * hardware scan support

iwlwifi
 * support UHB TAS enablement via BIOS
 * remove a bunch of W=1 warnings
 * add support for channel switch offload
 * support 32 Rx AMPDU sessions in newer devices
 * add support for a couple of new devices
 * add support for band disablement via BIOS

mt76
 * mt7915 thermal management improvements
 * SAR support for more mt76 drivers
 * mt7986 wmac support on mt7915

ath11k
 * debugfs interface to configure firmware debug log level
 * debugfs interface to test Target Wake Time (TWT)
 * provide 802.11ax High Efficiency (HE) data via radiotap

ath9k
 * use hw_random API instead of directly dumping into random.c

wcn36xx
 * fix wcn3660 to work on 5 GHz band

ath6kl
 * add device ID for WLU5150-D81

cfg80211/mac80211
 * initial EHT (from 802.11be) support
   (EHT rates, 320 MHz, larger block-ack)
 * support disconnect on HW restart

* tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (247 commits)
  mac80211: Add support to trigger sta disconnect on hardware restart
  mac80211: fix potential double free on mesh join
  mac80211: correct legacy rates check in ieee80211_calc_rx_airtime
  nl80211: fix typo of NL80211_IF_TYPE_OCB in documentation
  mac80211: Use GFP_KERNEL instead of GFP_ATOMIC when possible
  mac80211: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
  rtw89: 8852c: process logic efuse map
  rtw89: 8852c: process efuse of phycap
  rtw89: support DAV efuse reading operation
  rtw89: 8852c: add chip::dle_mem
  rtw89: add page_regs to handle v1 chips
  rtw89: add chip_info::{h2c,c2h}_reg to support more chips
  rtw89: add hci_func_en_addr to support variant generation
  rtw89: add power_{on/off}_func
  rtw89: read chip version depends on chip ID
  rtw89: pci: use a struct to describe all registers address related to DMA channel
  rtw89: pci: add V1 of PCI channel address
  rtw89: pci: add struct rtw89_pci_info
  rtw89: 8852c: add 8852c empty files
  MAINTAINERS: add devicetree bindings entry for mt76
  ...

====================

Link: https://lore.kernel.org/r/20220311124029.213470-1-johannes@sipsolutions.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for creating filters for GTP-U and GTP-C in switchdev mode. Add
support for parsing GTP-specific options (QFI and PDU type) and TEID.

By default, a filter for GTP-U will be added. To add a filter for GTP-C,
specify enc_dst_port = 2123, e.g.:

tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
enc_dst_port 2123 action mirred egress redirect dev $VF1_PR

Note: GTP-U with outer IPv6 offload is not supported yet.
Note: GTP-U with no payload offload is not supported yet.
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>