- 21 Feb, 2007 40 commits
-
-
Michael Krufky authored
Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@infradead.org>
-
Michael Krufky authored
Signed-off-by:
-
Aapo Tahkola authored
Currently, the driver works in bulk mode supporting both USB 2.0 and 1.0 with and without hardware pid filters. The ULi m9205 also supports isochronous transfer mode, but I have dropped support for it because it depends on firmware and does not work on all USB host chips. Further, I have no firmware with remote controller support for this mode. Signed-off-by:
Aapo Tahkola <aet@rasterburn.org> Signed-off-by:
-
Tino Keitel authored
I noticed that udev does not create a symlink for the CinergyT2 remote input device in /dev/input/by-id, which is required if I want to have a unique device name for lircd. The attached patch tries to achive this. However, udev still omits the input device for /dev/input/by-id symlinks. I think something is still not reported correctly. Signed-off-by:
Tino Keitel <tino.keitel@tikei.de> Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Mauro Carvalho Chehab authored
pvrusb2 have only one tuner inside. However, as it were not handling index, a call to v4l-info were returning as if it were an infinite number of tuners: $ v4l-info|grep VIDIOC_G_TUNER |head -5 VIDIOC_G_TUNER(0) VIDIOC_G_TUNER(1) VIDIOC_G_TUNER(2) VIDIOC_G_TUNER(3) VIDIOC_G_TUNER(4) Acked-by:Mike Isely <isely@isely.net> Signed-off-by:
-
Mauro Carvalho Chehab authored
pvrusb2-encoder.c: In function 'pvr2_encoder_cmd': pvrusb2-encoder.c:195: warning: format '%u' expects type 'unsigned int', but argument 3 has type 'long unsigned int' pvrusb2-encoder.c:205: warning: format '%u' expects type 'unsigned int', but argument 3 has type 'long unsigned int' pvrusb2-encoder.c: In function 'pvr2_encoder_vcmd': pvrusb2-encoder.c:303: warning: format '%u' expects type 'unsigned int', but argument 3 has type 'long unsigned int' Acked-by:
-
Heiko Baums authored
Adds support for the combined S-Video/Composite input of the Terratec Cinergy 1400 DVB-T. Signed-off-by:
Heiko Baums <heiko@baums-on-web.de> Signed-off-by:
-
Marco Schluessler authored
Nexus CA needs to use a different routing on saa7115 module. Signed-off-by:
Marco Schluessler <marco@lordzodiac.de> Signed-off-by:
-
Michael Krufky authored
Add support for Terratec Cinergy HT PCI Signed-off-by:
Giorgio Moscardi <software@sukkology.net> Signed-off-by:
-
Mauro Carvalho Chehab authored
The video_ioctl2 conversion replaced the default from NTSC to PAL_BG. This broke cx88-blackbird. Probably, there are some badness at this driver, not doing all required stuff to change video standard. Signed-off-by: -
Mauro Carvalho Chehab authored
This patch finishes cx88-blackbird conversion to use video_ioctl2. Video standards are generated automatically inside videodev.c. the big ioctl parser is removed, using, instead, video_ioctl2. Signed-off-by: -
Mauro Carvalho Chehab authored
cx88_ioctl were merged at the master ioctl handler on cx88-blackbird Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Reorder some ioctl handlers to make easy to convert to video_ioctl2 Signed-off-by: -
Mauro Carvalho Chehab authored
cx88-blackbird were using some ioctl handling that were previously on cx88-video. Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
v4l2_tvnorm were meant to describe video standards and its names to V4L2 API. However, this were doing by some static structures at the driver. This patch changes the internals in a way that, at the driver, only a v4l2_tvnorm (a 64 bit integer) should be filled, with all supported tvnorms. videodev will dynamically generate the proper API array based on supported standards. Signed-off-by: -
Mauro Carvalho Chehab authored
video_mux is renamed to cx88_video_mux to be exported to cx88-blackbird Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
video_ioctl2 handler provides V4L2 API parsing. Using it makes the driver simpler, and isolates API parsing. This allows future reusage of driver controls using other ways, like sysfs and/or procfs and increases isolation of driver-specific handling from the generic common ioctl processing. Signed-off-by: -
Pantelis Koukousoulas authored
With the previous patch, mplayer started but was polling the video device forever without any video actually coming out. Further analysis showed that it does a VIDIOC_S_FMT with width and height set to -1 (!!!). The code handling this only cares that both are lower than the minimum range allowed so it ends up setting the size to 19x17 (!!) This pretty much breaks the encoder here. Even if this breakage is yet another (TM) result of my setup, setting the size to 19x17 by default would surprise most users IMHO. So, special case for -1 and interpret this to be a request for the default size, please. Users can then set their favorite size both through mplayer and through sysfs. With this patch, mplayer finally works in pvr:// mode (not that we really gain anything over operating it through sysfs with lirc, sometime I might actually get off my lazy a** and contribute this setup too) Signed-off-by:
Pantelis Koukousoulas <pakt223@freemail.gr> Signed-off-by:
Mike Isely <isely@pobox.com> Signed-off-by:
-
Pantelis Koukousoulas authored
This should allow mplayer pvr:// to start. The trick is that no matter what actual input we use under this "fake" one, it will be able to do stereo :-) Signed-off-by:
-
Mike Isely authored
Audio mode changes are not private to the audio chip - other I2C modules need to see this as well. And since the command in question is VIDIOC_S_TUNER which is a standard v4l2 command, we really should be broadcasting it out. This change sets up a broadcast pathway for VIDIOC_S_TUNER and also eliminates the now redundant code from the audio chip handler. This fix enables stereo reception for the FM radio Signed-off-by:
-
Mike Isely authored
Signed-off-by:
-
Mike Isely authored
Signed-off-by:
-
Ahmed S. Darwish authored
Signed-off-by:
Ahmed S. Darwish <darwish.07@gmail.com> Signed-off-by:
-
Mike Isely authored
Attempts to enumerate or operate on a group of EXT_CTRLS where the group size is zero is OK; don't fail on such operations. At least one application uses this to probe for the existence of this API so let it succeed. Signed-off-by:
-
Mike Isely authored
Signed-off-by:
-
Mike Isely authored
This bug caused uninitalized data to be returned during a G_TUNER status poll. Signed-off-by:
-
Mike Isely authored
The lack of a break statement in the handling of VIDIOC_S_TUNER caused errors to result. Fixed. Signed-off-by:
-
Mike Isely authored
Signed-off-by:
-
Mike Isely authored
Rather than hardcoding frequency ranges everywhere, rely on VIDIOC_G_TUNER results wherever we can. Signed-off-by:
-
Mike Isely authored
The automodeswitch control was a feature that enable automatic radio / tv switching based on the selected frequency. However since frequency ranges can overlap and also since apparently in some cases it's possible for the same frequency range to be both tv and radio in a specific region, then this feature can't safely work. So it's removed. Signed-off-by:
-
Mike Isely authored
Signed-off-by:
-
Mike Isely authored
Clean up use of VIDIOC_G_TUNER; we now correctly gather info from all the I2C client modules. Also abide by V4L2_TUNER_CAP_LOW appropriately. Signed-off-by:
-
Mike Isely authored
Signed-off-by:
-
