- 23 Apr, 2022 16 commits
-
-
Ping-Ke Shih authored
Prepare functions to configure channel and bandwidth accordingly. Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220414062027.62638-10-pkshih@realtek.com
-
Ping-Ke Shih authored
HFC is short for HCI flow control, and these parameters is used to configure PCI quota for TX/RX. Signed-off-by:
-
Ping-Ke Shih authored
Define efuse struct to access gain offset, and store them for further use by setting channel. Signed-off-by:
-
Zong-Zhe Yang authored
Add parser for bb gain table and configure bb gain table for 8852c. While ctrl_ch, obtain bb gain error settings and write them to phy. Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
chip_ops::bb_sethw is to initialize BB settings out of BB parameters tables. Once switching channel or initialing, we do chip_ops::bb_reset to reset hardware counters and states to make things in expectation. Signed-off-by:
-
Ping-Ke Shih authored
TSSI is used to manage TX power with thermal value as a factor. This patch is to configure bandedge to TX proper waveform. Signed-off-by:
-
Zong-Zhe Yang authored
TX power track tables are used to do TX power compensation according to thermal value. In order to work in existing and new chip, add new 6G entries, and change type from u8 to s8. Internal version table is HALRF_027_00_031. Signed-off-by:
-
Ping-Ke Shih authored
TX power depends on rate, but must follow regulation for specific country. Once asked to set channel, we configure registers according to these TX power tables. Signed-off-by:
-
Ping-Ke Shih authored
These parameters are used to initialize BB and RF hardware when we are going to bring up interface and start to transmit and receive. Signed-off-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Minghao Chi <chi.minghao@zte.com.cn> Signed-off-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
-
- 13 Apr, 2022 4 commits
-
-
Ping-Ke Shih authored
Fix wrong checking statement. Fortunately, this wrong code doesn't affect existing chip. Fixes: 740c431c ("rtw89: pci: add register definition to rtw89_pci_info to generalize pci code") Signed-off-by:
-
Ping-Ke Shih authored
Add to configure security CAM while mac80211 calls set_key and del_key. Signed-off-by:
-
Ping-Ke Shih authored
DCTL is short for D-MAC control that V1 chip uses this H2C to configure security CAM. Implement the callers in next patch. Signed-off-by:
-
Ping-Ke Shih authored
In order to support new chip that has capability of 160M, we need new format to fill new information, so add a new V1 ID for newer use. Since most fields are the same, fill fields according to the function ID of chip. Signed-off-by:
-
- 12 Apr, 2022 20 commits
-
-
Kalle Valo authored
This is an immutable branch shared between wireless-next and staging-next for moving wfx driver out of staging to drivers/net/wireless directory.
-
Lv Ruyi authored
There are some spelling mistakes in the comments. Fix it. Reported-by:
Lv Ruyi <lv.ruyi@zte.com.cn> Acked-by:
-
Lv Ruyi authored
There are some spelling mistakes in the comments. Fix it. Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
-
Jimmy Hon authored
Make workaround work for other 8821CE devices with different PCI ID Signed-off-by:
Jimmy Hon <honyuenkwun@gmail.com> Reviewed-by:
-
Jimmy Hon authored
New device ID 0xb821 found on TP-Link T2E Tested it with c821 driver. 2.4GHz and 5GHz works. PCI id: 05:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device b821 Subsystem: Realtek Semiconductor Co., Ltd. Device b821 Signed-off-by: -
Po-Hao Huang authored
RSSI value per frame is reported to mac80211 but not maintained in our own statistics, add it back to help us debug. Signed-off-by:
Po-Hao Huang <phhuang@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
Calling calibration to yield expected PHY performance. We do this in STA mode, so do this in AP mode as well. Signed-off-by:
-
Po-Hao Huang authored
Without this setting, hardware would not report to driver even if management frames are transmitted successfully. So we fix it. Signed-off-by:
-
Po-Hao Huang authored
To support stations in power saving mode, AP should notify stations that there are frames buffered at the AP via TIM during beacons. Driver used to transmit identical beacons that were downloaded to hardware during the initiation phase. This beacon will become obsolete over time. If the beacon does not contain sufficient information, station would not be able to percept that there is data to receive. Hence it won't wake up and start the PS-poll procedure, this could lead to timeout and/or lost data segments. In order to resolve this issue, driver will now download beacon to hardware whenever the content is updated. Enable hardware to update dtim_count for more efficiency, this reduces the overhead of downloading beacon at every beacon interval since most of the time only the dtim_count needs to be updated. Change queue mapping for broadcast/multicast frames to high queue, so these frames can be prioritized and sent when dtim_count is zero. Signed-off-by:
-
Po-Hao Huang authored
We should only fill in frequency reported by firmware during scan. Add this so frames won't be dropped by mac80211 due to frequency mismatch. Signed-off-by:
-
Po-Hao Huang authored
Adding this allows us to get notification when bitrate configuration of the station changes. Update according parameters to firmware so the rate control algorithm can work properly. Signed-off-by:
-
Joe Perches authored
Change the struct and the uses to const to reduce data. $ size drivers/net/wireless/realtek/rtw89/ser.o* (x86-64 defconfig w/ rtw89) text data bss dec hex filename 3741 8 0 3749 ea5 drivers/net/wireless/realtek/rtw89/ser.o.new 3437 312 0 3749 ea5 drivers/net/wireless/realtek/rtw89/ser.o.old Signed-off-by:
Joe Perches <joe@perches.com> Acked-by:
-
Chia-Yuan Li authored
Initialize registers to default values, such as PTA and GNT pin, and set pin MUX according to number of antenna on hardware module. Signed-off-by:
Chia-Yuan Li <leo.li@realtek.com> Signed-off-by:
-
Johnson Lin authored
Separated DIG RX gain, IGI configurations from not supportted HW using "support_igi" capability flag. Signed-off-by:
Johnson Lin <johnson.lin@realtek.com> Signed-off-by:
-
Chia-Yuan Li authored
Disable watchdog timer to prevent it timeout suddenly. Signed-off-by:
-
Ping-Ke Shih authored
BA CAM is used to react receiving AMPDU packets, so reset them to be expected initial state. Signed-off-by:
-
Ping-Ke Shih authored
The bit B_AX_SS_NONEMPTY_SS2FINFO_EN should be clear, because we configure C-MAC as hardware TX/RX mode. Signed-off-by:
-
Ping-Ke Shih authored
Turn on ERR IMR, and then firmware can capture interrupts reflecting errors to recover hardware states. Signed-off-by:
-
Chia-Yuan Li authored
Similarly, create functions to set specific C-MAC masks for firmware recovery. Signed-off-by:
-
