- 31 Mar, 2022 18 commits
-
-
Marek Vasut authored
The TC358767/TC358867/TC9595 are all capable of operating in multiple modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Add support for the DSI-to-DPI mode. This requires skipping most of the (e)DP initialization code, which is currently a large part of this driver, hence it is better to have far simpler separate tc_dpi_bridge_funcs and their implementation. The configuration of DPI output is also much simpler. The configuration of the DSI input is rather similar to the other TC bridge chips. The Pixel PLL in DPI output mode does not have the 65..150 MHz limitation imposed on the (e)DP output mode, so this limitation is skipped to permit operating panels with far slower pixel clock, even below 9 MHz. This mode of operation of the PLL is valid and tested. The detection of bridge mode is now added into tc_probe_bridge_mode(), where in case a DPI panel is found on port@1 endpoint@1, the mode is assumed to be DSI-to-DPI. If (e)DP is detected on port@2, the mode is assumed to be DPI-to-(e)DP. The DSI-to-(e)DP mode is not supported due to lack of proper hardware, but this would be some sort of mix between the two aforementioned modes. Reviewed-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
Marek Vasut <marex@denx.de> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by:
Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-12-marex@denx.de
-
Marek Vasut authored
The tc_set_video_mode() sets up both common and (e)DP video mode settings of the bridge chip. Split the function into tc_set_common_video_mode() to set the common settings and tc_set_edp_video_mode() to set the (e)DP specific settings. No functional change. Reviewed-by:
-
Marek Vasut authored
The TC358767/TC358867/TC9595 are all capable of operating in multiple modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Only the first mode is currently supported. It is possible to find out the mode in which the bridge should be operated by testing connected endpoints in DT. Port allocation: port@0 - DSI input port@1 - DPI input/output port@2 - eDP output Possible connections: DPI -> port@1 -> port@2 -> eDP :: [port@0 is not connected] DSI -> port@0 -> port@2 -> eDP :: [port@1 is not connected] DSI -> port@0 -> port@1 -> DPI :: [port@2 is not connected] Add function to determine the bridge mode based on connected endpoints. Reviewed-by:
-
Marek Vasut authored
The bridge ops are specific to the bridge configuration, move them into tc_probe_edp_bridge_endpoint() to permit cleaner addition of DSI-to-DPI mode. No functional change. Reviewed-by:
-
Marek Vasut authored
This bit of code is (e)DP and aux I2C link specific, move it into tc_aux_link_setup() to permit cleaner addition of DSI-to-DPI mode. No functional change. Reviewed-by:
-
Marek Vasut authored
The TC358767/TC358867/TC9595 are all capable of operating in multiple modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Only the first mode is currently supported. In order to support the rest of the modes without making the tc_probe() overly long, split the bridge endpoint parsing into dedicated function, where the necessary logic to detect the bridge mode based on which endpoints are connected, can be implemented. Reviewed-by:
-
Marek Vasut authored
Implement .atomic_check callback which prevents user space from setting unsupported mode. The tc_edp_common_atomic_check() variant is already prepared for DSI-to-DPI mode addition, which has different frequency limits. Reviewed-by:
-
Marek Vasut authored
Use the atomic version of the enable/disable operations to continue the transition to the atomic API. This will be needed to access the mode from the atomic state. Reviewed-by:
-
Marek Vasut authored
These functions are specific to (e)DP output initialization and operation, add specific tc_edp_ prefix to those functions to discern them from DPI output functions that will be added later in this series. No functional change. Reviewed-by:
-
Marek Vasut authored
It is necessary to specify the number of connected/used DSI data lanes when using the DSI input port of this bridge. Document the 'data-lanes' property of the DSI input port. Reviewed-by:
Rob Herring <robh@kernel.org> Acked-by:
-
Marek Vasut authored
The TC358767/TC358867/TC9595 are all capable of operating in multiple modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Document support for the DPI output port, which can now be connected both as input and output. Acked-by:
-
Lucas Stach authored
When the probe routine fails we also need to clean up the CEC adapter registered in adv7511_cec_init(). Fixes: 3b1b9750 ("drm: adv7511/33: add HDMI CEC support") Signed-off-by:
-
Yang Yingliang authored
Add the missing destroy_workqueue() before return from anx7625_i2c_probe() in the error handling case. Fixes: adca62ec ("drm/bridge: anx7625: Support reading edid through aux channel") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Reviewed-by:
Hsin-Yi Wang <hsinyi@chromium.org> Signed-off-by:
-
Jani Nikula authored
The invalid EDID block filtering uses the number of valid EDID extensions instead of all EDID extensions for looping the extensions in the copy. This is fine, by coincidence, if all the invalid blocks are at the end of the EDID. However, it's completely broken if there are invalid extensions in the middle; the invalid blocks are included and valid blocks are excluded. Fix it by modifying the base block after, not before, the copy. Fixes: 14544d09 ("drm/edid: Only print the bad edid when aborting") Reported-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Reviewed-by:
-
Maxime Ripard authored
The HVS state configuration is useful when debugging what's going on in the vc4 hardware pipeline. Add an implementation of .atomic_print_state. Acked-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220328124304.2309418-5-maxime@cerno.tech
-
Maxime Ripard authored
None of those helpers modify the pointed data, let's make them const. Acked-by:
-
Maxime Ripard authored
A number of drivers (amdgpu, komeda, vc4, etc.) leverage the drm_private_state structure, but we don't have any infrastructure to provide debugging like we do for the other components state. Let's add an atomic_print_state hook to be consistent. Reviewed-by:
-
Maxime Ripard authored
The DRM_UT_STATE controls whether we're calling drm_atomic_print_new_state() whenever a new state is committed. However, that call is made in the drm_mode_atomic_ioctl(), whereas we have multiple users of the drm_atomic_commit() function in the kernel (framebuffer emulation, drm_atomic_helper_dirtyfb, etc.). This leads to multiple states being committed but never actually displayed even though we asked to have verbose atomic state debugging. Let's move the call to drm_atomic_print_new_state() to drm_atomic_commit() to make sure we don't miss any. Non-blocking commits were never logged though, and it would create too much churn in the logs to do so, so leave them out for now. Signed-off-by:
-
- 30 Mar, 2022 1 commit
-
-
Matthias Kaehlcke authored
Two digits are swapped in the AUO B133UAN01 panel id (0x8495 instead of 0x8594). This went initially unnoticed because the panel is still detected, though it is set up with a conservative default timing. Fix the digit swap. Fixes: ec57376f ("drm/panel-edp: Add AUO B133UAN01") Signed-off-by:
Matthias Kaehlcke <mka@chromium.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
- 29 Mar, 2022 18 commits
-
-
Matthias Kaehlcke authored
Add support for the AUO B133UAN01 13.3" WUXGA panel. Signed-off-by:
-
Jani Nikula authored
Reduce the size of the function that actually modifies the EDID. Signed-off-by:
Emil Velikov <emil.l.velikov@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/437c3c79f68d1144444fb2dd18a678f3aa97272c.1648477901.git.jani.nikula@intel.com
-
Jani Nikula authored
With this, the remaining non-const parts are the ones that actually modify the EDID, for example to fix corrupt EDID. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
Finalize detailed timing parsing constness by making struct edid also const in callbacks and closure. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
Constify the first level of struct edid in detailed timing parsing. Also switch to struct edid instead of u8. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
Moving one level higher, constify struct detailed_timing pointers in callbacks. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
Start constifying the struct detailed_timing pointers being passed around from bottom up. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
Use struct detailed_timing member access instead of direct offsets to avoid casting. Use BUILD_BUG_ON() for sanity check. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
Use struct detailed_timing member access instead of direct offsets to avoid casting. Use BUILD_BUG_ON() for sanity check. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
Use struct member access instead of direct offsets to avoid a cast. Use BUILD_BUG_ON() for sanity check. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
Use struct member access instead of direct offsets to avoid lots of casts all over the place. Use BUILD_BUG_ON() for sanity check. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
The reduced blanking bit is valid only for CVT, indicated by display range limits flags 0x04. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
We'll want to keep the EDID immutable while parsing. Stop modifying the EDID because of the quirks. In theory, this does have userspace implications, but the userspace is supposed to use the modes exposed via KMS API, not by parsing the EDID directly. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Xiaomeng Tong authored
The bug is here: if (!encoder) { The list iterator value 'encoder' will *always* be set and non-NULL by list_for_each_entry(), so it is incorrect to assume that the iterator value will be NULL if the list is empty or no element is found. To fix the bug, use a new variable 'iter' as the list iterator, while use the original variable 'encoder' as a dedicated pointer to point to the found element. Cc: stable@vger.kernel.org Fixes: ec9eab09 ("drm/tilcdc: Add drm bridge support for attaching drm bridge drivers") Signed-off-by:Xiaomeng Tong <xiam0nd.tong@gmail.com> Reviewed-by:
Jyri Sarha <jyri.sarha@iki.fi> Tested-by:
-
Xiaomeng Tong authored
The bug is here: return crtc; The list iterator value 'crtc' will *always* be set and non-NULL by list_for_each_entry(), so it is incorrect to assume that the iterator value will be NULL if the list is empty or no element is found. To fix the bug, return 'crtc' when found, otherwise return NULL. Cc: stable@vger.kernel.org fixes: 89c78134 ("gma500: Add Poulsbo support") Signed-off-by:
Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220327052028.2013-1-xiam0nd.tong@gmail.com
-
Christian König authored
We have the BO pointer in the base structure now as well. Signed-off-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl> Link: https://patchwork.freedesktop.org/patch/msgid/20220321132601.2161-6-christian.koenig@amd.com
-
Christian König authored
Instead of providing the bulk move structure for each LRU update set this as property of the BO. This should avoid costly bulk move rebuilds with some games under RADV. v2: some name polishing, add a few more kerneldoc words. v3: add some lockdep v4: fix bugs, handle pin/unpin as well v5: improve kerneldoc Signed-off-by:
-
Christian König authored
Those functions are going to become more complex, don't inline them any more. Signed-off-by:
-
- 28 Mar, 2022 3 commits
-
-
Xiaomeng Tong authored
The bug is here: return encoder; The list iterator value 'encoder' will *always* be set and non-NULL by drm_for_each_encoder_mask(), so it is incorrect to assume that the iterator value will be NULL if the list is empty or no element found. Otherwise it will bypass some NULL checks and lead to invalid memory access passing the check. To fix this bug, just return 'encoder' when found, otherwise return NULL. Cc: stable@vger.kernel.org Fixes: 12885ecb ("drm/nouveau/kms/nvd9-: Add CRC support") Signed-off-by:
Lyude Paul <lyude@redhat.com> [Changed commit title] Signed-off-by:
-
Christian König authored
Not just TT and VRAM. Signed-off-by:
-
Christian König authored
Instead of duplicating that at different places add an iterator over all the resources in a resource manager. v2: add lockdep annotation and kerneldoc v3: fix various bugs pointed out by Felix v4: simplify the code a bit more Signed-off-by:
Felix Kuehling <Felix.Kuehling@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220321132601.2161-2-christian.koenig@amd.com
-
