This patch allows configuring IPIP, sit, and GRE tunnels to use GUE.
This is very similar to fou excpet that we need to insert the GUE header
in addition to the UDP header on transmit.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support receiving for GUE packets in the fou module. The
fou module now supports direct foo-over-udp (no encapsulation header)
and GUE. To support this a type parameter is added to the fou netlink
parameters.

For a GUE socket we define gue_udp_recv, gue_gro_receive, and
gue_gro_complete to handle the specifics of the GUE protocol. Most
of the code to manage and configure sockets is common with the fou.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes fou[46]_gro_receive and fou[46]_gro_complete
functions. The v4 or v6 variants were chosen for the UDP offloads
based on the address family of the socket this is not necessary
or correct. Alternatively, this patch adds is_ipv6 to napi_gro_skb.
This is set in udp6_gro_receive and unset in udp4_gro_receive. In
fou_gro_receive the value is used to select the correct inet_offloads
for the protocol of the outer IP header.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When adjusting max_header for the tunnel interface based on egress
device we need to account for any extra bytes in secondary encapsulation
(e.g. FOU).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_gro_receive() is only called from tcp_gro_receive() which is
not in a module.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SH_IRDA needs HAS_IOMEM, so depend on it. The related error(with
allmodconfig under um):

    CC [M]  drivers/net/irda/sh_irda.o
  drivers/net/irda/sh_irda.c: In function ‘sh_irda_probe’:
  drivers/net/irda/sh_irda.c:776:2: error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration]
    self->membase = ioremap_nocache(res->start, resource_size(res));
    ^
  drivers/net/irda/sh_irda.c:776:16: warning: assignment makes pointer from integer without a cast [enabled by default]
    self->membase = ioremap_nocache(res->start, resource_size(res));
                  ^
  drivers/net/irda/sh_irda.c:821:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
    iounmap(self->membase);
    ^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PXA168_ETH need HAS_IOMEM, so depend on it, the related error (with
allmodconfig under um):

    CC [M]  drivers/net/ethernet/marvell/pxa168_eth.o
  drivers/net/ethernet/marvell/pxa168_eth.c: In function ‘pxa168_eth_probe’:
  drivers/net/ethernet/marvell/pxa168_eth.c:1605:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
    iounmap(pep->base);
    ^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NET_DSA_BCM_SF2 need HAS_IOMEM, so depend on it, the related error (with
allmodconfig under um):

    CC [M]  drivers/net/dsa/bcm_sf2.o
  drivers/net/dsa/bcm_sf2.c: In function ‘bcm_sf2_sw_setup’:
  drivers/net/dsa/bcm_sf2.c:487:3: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
     iounmap(*base);
     ^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CAN_AT91 needs HAS_IOMEM, so depends on it. The related error (with
allmodconfig under um):

    CC [M]  drivers/net/can/at91_can.o
  drivers/net/can/at91_can.c: In function ‘at91_can_probe’:
  drivers/net/can/at91_can.c:1329:2: error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration]
  addr = ioremap_nocache(res->start, resource_size(res));
    ^
  drivers/net/can/at91_can.c:1329:7: warning: assignment makes pointer from integer without a cast [enabled by default]
    addr = ioremap_nocache(res->start, resource_size(res));
         ^
  drivers/net/can/at91_can.c:1384:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
    iounmap(addr);
    ^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-10-02

This series contains updates to fm10k, igb, ixgbe and i40e.

Alex provides two updates to the fm10k driver.  First reduces the buffer
size to 2k for all page sizes, since most frames only have a 1500 MTU
so supporting a buffer size larger than this is somewhat wasteful.
Second fixes an issue where the number of transmit queues was not being
updated, so added the lines necessary to update the number of transmit
queues.

Rick Jones provides two patches to convert ixgbe, igb and i40e to use
dev_consume_skb_any().

Emil provides two patches for ixgbe, first cleans up a couple of wait
loops on auto-negotiation that were not needed.  Second fixes an issue
reported by Fujitsu/Red Hat, which consolidates the logic behind the
dynamically setting of TXDCTL.WTHRESH depending on interrupt throttle
rate (ITR) setting regardless of BQL.

Ethan Zhao provides a cleanup patch for ixgbe where he noticed a
duplicate define.

Bernhard Kaindl provides a patch for igb to remove a source of latency
spikes by not calling code that uses mdelay() for feeding a PHY stat
while being called with a spinlock held.

Todd bumps the igb version based on the recent changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Eli Cohen says:

====================
mlx5 update for 3.18

This series integrates a new mechanism for populating and extracting field values
used in the driver/firmware interaction around command mailboxes.

Changes from V1:
 - Remove unused definition of memcpy_cpu_to_be32()
 - Remove definitions of non_existent_*() and use BUILD_BUG_ON() instead.
 - Added a patch one line patch to add support for ConnectX-4 devices.

Changes from V0:
 - trimmed the auto-generated file to a minimum, as required by the reviewers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the upcoming ConnectX-4 device to the list of supported devices by then
mlx5 driver.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch puts a common part as the first field of mlx5_core_qp. This field is
used to identify which resource generated an event. This is required since upcoming
new resource types such as DC targets are allocated for the same numerical space
as regular QPs and may generate the same events. By searching the resource in the
same table we can then look at the common field to identify the resource.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Transform device capabilities related commands to use set/get macros to
manipulate command mailboxes.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add an auto generated header file that describes hardware registers along with
set of macros that set/get values. The macros do static checks to avoid
overflow, handle endianess, and overall provide a clean way to code commands.
Currently the header file is small and we will add structs as we make use of
the macros.
A few commands were removed from the commands enum since they are not supported
currently and will be added when support is available.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rearrange struct mlx5_caps so it has a "gen" field to represent the current
capabilities configured for the device. Max capabilities can also be queried
from the device. Also update capabilities struct to contain more fields as per
the latest revision if firmware specification.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Validation of skb can be pretty expensive :

GSO segmentation and/or checksum computations.

We can do this without holding qdisc lock, so that other cpus
can queue additional packets.

Trick is that requeued packets were already validated, so we carry
a boolean so that sch_direct_xmit() can validate a fresh skb list,
or directly use an old one.

Tested on 40Gb NIC (8 TX queues) and 200 concurrent flows, 48 threads
host.

Turning TSO on or off had no effect on throughput, only few more cpu
cycles. Lock contention on qdisc lock disappeared.

Same if disabling TX checksum offload.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to call ether_setup after alloc_ethdev since it was
already called there.

Follow commits c706471b ("net: axienet: remove unnecessary
ether_setup after alloc_etherdev") and 3c87dcbf ("net: ll_temac:
Remove unnecessary ether_setup after alloc_etherdev") and fix the
pattern in all remaining ethernet drivers.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jesper Dangaard Brouer says:

====================
qdisc: bulk dequeue support

This patchset uses DaveM's recent API changes to dev_hard_start_xmit(),
from the qdisc layer, to implement dequeue bulking.

Patch01: "qdisc: bulk dequeue support for qdiscs with TCQ_F_ONETXQUEUE"
 - Implement basic qdisc dequeue bulking
 - This time, 100% relying on BQL limits, no magic safe-guard constants

Patch02: "qdisc: dequeue bulking also pickup GSO/TSO packets"
 - Extend bulking to bulk several GSO/TSO packets
 - Seperate patch, as it introduce a small regression, see test section.

We do have a patch03, which exports a userspace tunable as a BQL
tunable, that can byte-cap or disable the bulking/bursting.  But we
could not agree on it internally, thus not sending it now.  We
basically strive to avoid adding any new userspace tunable.

Testing patch01:
================
 Demonstrating the performance improvement of qdisc dequeue bulking, is
tricky because the effect only "kicks-in" once the qdisc system have a
backlog. Thus, for a backlog to form, we need either 1) to exceed wirespeed
of the link or 2) exceed the capability of the device driver.

For practical use-cases, the measureable effect of this will be a
reduction in CPU usage

01-TCP_STREAM:
--------------
Testing effect for TCP involves disabling TSO and GSO, because TCP
already benefit from bulking, via TSO and especially for GSO segmented
packets.  This patch view TSO/GSO as a seperate kind of bulking, and
avoid further bulking of these packet types.

The measured perf diff benefit (at 10Gbit/s) for a single netperf
TCP_STREAM were 9.24% less CPU used on calls to _raw_spin_lock()
(mostly from sch_direct_xmit).

If my E5-2695v2(ES) CPU is tuned according to:
 http://netoptimizer.blogspot.dk/2014/04/basic-tuning-for-network-overload.html
Then it is possible that a single netperf TCP_STREAM, with GSO and TSO
disabled, can utilize all bandwidth on a 10Gbit/s link.  This will
then cause a standing backlog queue at the qdisc layer.

Trying to pressure the system some more CPU util wise, I'm starting
24x TCP_STREAMs and monitoring the overall CPU utilization.  This
confirms bulking saves CPU cycles when it "kicks-in".

Tool mpstat, while stressing the system with netperf 24x TCP_STREAM, shows:
 * Disabled bulking: sys:2.58%  soft:8.50%  idle:88.78%
 * Enabled  bulking: sys:2.43%  soft:7.66%  idle:89.79%

02-UDP_STREAM
-------------
The measured perf diff benefit for UDP_STREAM were 6.41% less CPU used
on calls to _raw_spin_lock().  24x UDP_STREAM with packet size -m 1472 (to
avoid sending UDP/IP fragments).

03-trafgen driver test
----------------------
The performance of the 10Gbit/s ixgbe driver is limited due to
updating the HW ring-queue tail-pointer on every packet.  As
previously demonstrated with pktgen.

Using trafgen to send RAW frames from userspace (via AF_PACKET), and
forcing it through qdisc path (with option --qdisc-path and -t0),
sending with 12 CPUs.

I can demonstrate this driver layer limitation:
 * 12.8 Mpps with no qdisc bulking
 * 14.8 Mpps with qdisc bulking (full 10G-wirespeed)

Testing patch02:
================
Testing Bulking several GSO/TSO packets:

Measuring HoL (Head-of-Line) blocking for TSO and GSO, with
netperf-wrapper. Bulking several TSO show no performance regressions
(requeues were in the area 32 requeues/sec for 10G while transmitting
approx 813Kpps).

Bulking several GSOs does show small regression or very small
improvement (requeues were in the area 8000 requeues/sec, for 10G
while transmitting approx 813Kpps).

 Using ixgbe 10Gbit/s with GSO bulking, we can measure some additional
latency. Base-case, which is "normal" GSO bulking, sees varying
high-prio queue delay between 0.38ms to 0.47ms.  Bulking several GSOs
together, result in a stable high-prio queue delay of 0.50ms.

Corrosponding to:
 (10000*10^6)*((0.50-0.47)/10^3)/8 = 37500 bytes
 (10000*10^6)*((0.50-0.38)/10^3)/8 = 150000 bytes
 37500/1500  = 25 pkts
 150000/1500 = 100 pkts

 Using igb at 100Mbit/s with GSO bulking, shows an improvement.
Base-case sees varying high-prio queue delay between 2.23ms to 2.35ms
diff of 0.12ms corrosponding to 1500 bytes at 100Mbit/s. Bulking
several GSOs together, result in a stable high-prio queue delay of
2.23ms.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The TSO and GSO segmented packets already benefit from bulking
on their own.

The TSO packets have always taken advantage of the only updating
the tailptr once for a large packet.

The GSO segmented packets have recently taken advantage of
bulking xmit_more API, via merge commit 53fda7f7 ("Merge
branch 'xmit_list'"), specifically via commit 7f2e870f ("net:
Move main gso loop out of dev_hard_start_xmit() into helper.")
allowing qdisc requeue of remaining list.  And via commit
ce93718f ("net: Don't keep around original SKB when we
software segment GSO frames.").

This patch allow further bulking of TSO/GSO packets together,
when dequeueing from the qdisc.

Testing:
 Measuring HoL (Head-of-Line) blocking for TSO and GSO, with
netperf-wrapper. Bulking several TSO show no performance regressions
(requeues were in the area 32 requeues/sec).

Bulking several GSOs does show small regression or very small
improvement (requeues were in the area 8000 requeues/sec).

 Using ixgbe 10Gbit/s with GSO bulking, we can measure some additional
latency. Base-case, which is "normal" GSO bulking, sees varying
high-prio queue delay between 0.38ms to 0.47ms.  Bulking several GSOs
together, result in a stable high-prio queue delay of 0.50ms.

 Using igb at 100Mbit/s with GSO bulking, shows an improvement.
Base-case sees varying high-prio queue delay between 2.23ms to 2.35ms
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on DaveM's recent API work on dev_hard_start_xmit(), that allows
sending/processing an entire skb list.

This patch implements qdisc bulk dequeue, by allowing multiple packets
to be dequeued in dequeue_skb().

The optimization principle for this is two fold, (1) to amortize
locking cost and (2) avoid expensive tailptr update for notifying HW.
 (1) Several packets are dequeued while holding the qdisc root_lock,
amortizing locking cost over several packet.  The dequeued SKB list is
processed under the TXQ lock in dev_hard_start_xmit(), thus also
amortizing the cost of the TXQ lock.
 (2) Further more, dev_hard_start_xmit() will utilize the skb->xmit_more
API to delay HW tailptr update, which also reduces the cost per
packet.

One restriction of the new API is that every SKB must belong to the
same TXQ.  This patch takes the easy way out, by restricting bulk
dequeue to qdisc's with the TCQ_F_ONETXQUEUE flag, that specifies the
qdisc only have attached a single TXQ.

Some detail about the flow; dev_hard_start_xmit() will process the skb
list, and transmit packets individually towards the driver (see
xmit_one()).  In case the driver stops midway in the list, the
remaining skb list is returned by dev_hard_start_xmit().  In
sch_direct_xmit() this returned list is requeued by dev_requeue_skb().

To avoid overshooting the HW limits, which results in requeuing, the
patch limits the amount of bytes dequeued, based on the drivers BQL
limits.  In-effect bulking will only happen for BQL enabled drivers.

Small amounts for extra HoL blocking (2x MTU/0.24ms) were
measured at 100Mbit/s, with bulking 8 packets, but the
oscillating nature of the measurement indicate something, like
sched latency might be causing this effect. More comparisons
show, that this oscillation goes away occationally. Thus, we
disregard this artifact completely and remove any "magic" bulking
limit.

For now, as a conservative approach, stop bulking when seeing TSO and
segmented GSO packets.  They already benefit from bulking on their own.
A followup patch add this, to allow easier bisect-ability for finding
regressions.

Jointed work with Hannes, Daniel and Florian.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the ethernet driver for Agere et131x devices to
drivers/net/ethernet.

The driver being added has been in the staging tree for some time, and will be
removed from there in a seperate patch. This one merely disables the staging
version to prevent two instances being built.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/usb/r8152.c
	net/netfilter/nfnetlink.c

Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>

Bump version
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Convert two more Intel NIC drivers to dev_consume_skb_any() to help
make dropped packet profiling sane.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove a source of latency spikes (in my case up to 10ms) by not calling
code that uses mdelay() for feeding a phy statistic (rx errors for idle
symbols - not data -> idle_errors) while being called with a spinlock held.

As idle_errors isn't read, this patch only removes unused code and data.

Later, more complicated changes may be applied to address the spinlock and
allow for some PHY diagnostics by harvesting this PHY stats register fully.

This patch is designed to fix the issue and be safe for longterm/stable.

For the Intel e1000e driver, the same change was applied in 2008 with
commit 23033fad ("e1000e: remove phy read from inside spinlock").

The mdelay is triggered by HW/SW semaphores, thus it depends on the HW.

I've HW that triggers it even when idle. Others may trigger it only e.g.
when Ethernet ports aquire or loose the link or on ifconfig up / down.
We've noticed this first from delays in frame rx/tx due to the mdelay().

Example command for checking if the issue is triggered: cyclictest -Smp1
(Look for occasional "Max:" values > 4000 or use -b 4000 to stop if greater)

It was observed with I350 ports connected to other I350 ports, but not
if driver and EEPROM was modified to run the I350 in EEPROM-less mode.

phy_stats.idle_errors and .receive_errors (isn't touched) occupy 64 not
used bits in the adapter struct: Their allocation may be removed as well.

Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Fixes: 12dcd86b ("igb: fix stats handling") (this added the spin_lock)
Signed-off-by: Bernhard Kaindl <bk-linux@use.startmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There is typo in ixgbe.h, two marcro definition of IXGBE_MAX_L2A_QUEUES to 4,
delete one, clear the compiler warning.
Signed-off-by: Ethan Zhao <ethan.zhao@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch consolidates the logic behind dynamically setting TXDCTL.WTHRESH
depending on interrupt throttle rate (ITR) setting regardless of BQL.

Previously TXDCTL.WTHRESH was dynamically being set only with BQL being
enabled, but we have to set it regardless of BQL when ITR is low to avoid
Tx stalls/hangs.

CC: John Greene <jogreene@redhat.com>
Reported by: Masayuki Gouji <gouji.masayuki@jp.fujitsu.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes couple of wait loops on autoneg that are not needed.

During validation we noticed that the loops always time out, so there
should be no user impact.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Convert the normal packet completion path to dev_consume_skb_any() so
packet drop profiling via dropwatch or perf top -G -e skb_kfree_skb
is not cluttered with false hits.

Compile tested only.  There is a dev_kfree_skb_any() in the routine
ixgbe_ptp_tx_hwtstamp() in ixgbe_ptp.c that looks like a conversion
candidate but I wasn't familiar enough with the code to pull the
trigger.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The number of Tx queues was not being updated due to some issues when
generating the patches.  This change makes sure to add the lines necessary
to update the number of Tx queues correctly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change reduces the buffer size to 2K for all page sizes.  The basic
idea is that since most frames only have a 1500 MTU supporting a buffer
size larger than this is somewhat wasteful.  As such I have reduced the
size to 2K for all page sizes which will allow for more uses per page.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull networking fixes from David Miller:

 1) Don't halt the firmware in r8152 driver, from Hayes Wang.

 2) Handle full sized 802.1ad frames in bnx2 and tg3 drivers properly,
    from Vlad Yasevich.

 3) Don't sleep while holding tx_clean_lock in netxen driver, fix from
    Manish Chopra.

 4) Certain kinds of ipv6 routes can end up endlessly failing the route
    validation test, causing it to be re-looked up over and over again.
    This particularly kills input route caching in TCP sockets.  Fix
    from Hannes Frederic Sowa.

 5) netvsc_start_xmit() has a use-after-free access to skb->len, fix
    from K Y Srinivasan.

 6) Fix matching of inverted containers in ematch module, from Ignacy
    Gawędzki.

 7) Aggregation of GRO frames via SKB ->frag_list for linear skbs isn't
    handled properly, regression fix from Eric Dumazet.

 8) Don't test return value of ipv4_neigh_lookup(), which returns an
    error pointer, against NULL.  From WANG Cong.

 9) Fix an old regression where we mistakenly allow a double add of the
    same tunnel.  Fixes from Steffen Klassert.

10) macvtap device delete and open can run in parallel and corrupt lists
    etc., fix from Vlad Yasevich.

11) Fix build error with IPV6=m NETFILTER_XT_TARGET_TPROXY=y, from Pablo
    Neira Ayuso.

12) rhashtable_destroy() triggers lockdep splats, fix also from Pablo.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
  bna: Update Maintainer Email
  r8152: disable power cut for RTL8153
  r8152: remove clearing bp
  bnx2: Correctly receive full sized 802.1ad fragmes
  tg3: Allow for recieve of full-size 8021AD frames
  r8152: fix setting RTL8152_UNPLUG
  netxen: Fix bug in Tx completion path.
  netxen: Fix BUG "sleeping function called from invalid context"
  ipv6: remove rt6i_genid
  hyperv: Fix a bug in netvsc_start_xmit()
  net: stmmac: fix stmmac_pci_probe failed when CONFIG_HAVE_CLK is selected
  ematch: Fix matching of inverted containers.
  gro: fix aggregation for skb using frag_list
  neigh: check error pointer instead of NULL for ipv4_neigh_lookup()
  ip6_gre: Return an error when adding an existing tunnel.
  ip6_vti: Return an error when adding an existing tunnel.
  ip6_tunnel: Return an error when adding an existing tunnel.
  ip6gre: add a rtnl link alias for ip6gretap
  net/mlx4_core: Allow not to specify probe_vf in SRIOV IB mode
  r8152: fix the carrier off when autoresuming
  ...

Update the maintainer email for BNA driver.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bcmgenet_put_tx_csum() needs to return skb pointer back to the caller
because it reallocates a new one in case of lack of skb headroom.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch demonstrates the effect of delaying update of HW tailptr.
(based on earlier patch by Jesper)

burst=1 is the default. It sends one packet with xmit_more=false
burst=2 sends one packet with xmit_more=true and
        2nd copy of the same packet with xmit_more=false
burst=3 sends two copies of the same packet with xmit_more=true and
        3rd copy with xmit_more=false

Performance with ixgbe (usec 30):
burst=1  tx:9.2 Mpps
burst=2  tx:13.5 Mpps
burst=3  tx:14.5 Mpps full 10G line rate
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for being able to propagate port states to e.g: notifiers
or other kernel parts, do not manipulate the port state directly, but
instead use a helper function which will allow us to do a bit more than
just setting the state.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes the following crash:

[   63.976822] general protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
[   63.980094] CPU: 1 PID: 15 Comm: ksoftirqd/1 Not tainted 3.17.0-rc6+ #648
[   63.980094] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[   63.980094] task: ffff880117dea690 ti: ffff880117dfc000 task.ti: ffff880117dfc000
[   63.980094] RIP: 0010:[<ffffffff817e6d07>]  [<ffffffff817e6d07>] u32_destroy_key+0x27/0x6d
[   63.980094] RSP: 0018:ffff880117dffcc0  EFLAGS: 00010202
[   63.980094] RAX: ffff880117dea690 RBX: ffff8800d02e0820 RCX: 0000000000000000
[   63.980094] RDX: 0000000000000001 RSI: 0000000000000002 RDI: 6b6b6b6b6b6b6b6b
[   63.980094] RBP: ffff880117dffcd0 R08: 0000000000000000 R09: 0000000000000000
[   63.980094] R10: 00006c0900006ba8 R11: 00006ba100006b9d R12: 0000000000000001
[   63.980094] R13: ffff8800d02e0898 R14: ffffffff817e6d4d R15: ffff880117387a30
[   63.980094] FS:  0000000000000000(0000) GS:ffff88011a800000(0000) knlGS:0000000000000000
[   63.980094] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[   63.980094] CR2: 00007f07e6732fed CR3: 000000011665b000 CR4: 00000000000006e0
[   63.980094] Stack:
[   63.980094]  ffff88011a9cd300 ffffffff82051ac0 ffff880117dffce0 ffffffff817e6d68
[   63.980094]  ffff880117dffd70 ffffffff810cb4c7 ffffffff810cb3cd ffff880117dfffd8
[   63.980094]  ffff880117dea690 ffff880117dea690 ffff880117dfffd8 000000000000000a
[   63.980094] Call Trace:
[   63.980094]  [<ffffffff817e6d68>] u32_delete_key_freepf_rcu+0x1b/0x1d
[   63.980094]  [<ffffffff810cb4c7>] rcu_process_callbacks+0x3bb/0x691
[   63.980094]  [<ffffffff810cb3cd>] ? rcu_process_callbacks+0x2c1/0x691
[   63.980094]  [<ffffffff817e6d4d>] ? u32_destroy_key+0x6d/0x6d
[   63.980094]  [<ffffffff810780a4>] __do_softirq+0x142/0x323
[   63.980094]  [<ffffffff810782a8>] run_ksoftirqd+0x23/0x53
[   63.980094]  [<ffffffff81092126>] smpboot_thread_fn+0x203/0x221
[   63.980094]  [<ffffffff81091f23>] ? smpboot_unpark_thread+0x33/0x33
[   63.980094]  [<ffffffff8108e44d>] kthread+0xc9/0xd1
[   63.980094]  [<ffffffff819e00ea>] ? do_wait_for_common+0xf8/0x125
[   63.980094]  [<ffffffff8108e384>] ? __kthread_parkme+0x61/0x61
[   63.980094]  [<ffffffff819e43ec>] ret_from_fork+0x7c/0xb0
[   63.980094]  [<ffffffff8108e384>] ? __kthread_parkme+0x61/0x61

tp could be freed in call_rcu callback too, the order is not guaranteed.

John Fastabend says:

====================
Its worth noting why this is safe. Any running schedulers will either
read the valid class field or it will be zeroed.

All schedulers today when the class is 0 do a lookup using the
same call used by the tcf_exts_bind(). So even if we have a running
classifier hit the null class pointer it will do a lookup and get
to the same result. This is particularly fragile at the moment because
the only way to verify this is to audit the schedulers call sites.
====================

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the following crash:

[  166.670795] BUG: unable to handle kernel NULL pointer dereference at           (null)
[  166.674230] IP: [<ffffffff814b739f>] __list_del_entry+0x5c/0x98
[  166.674230] PGD d0ea5067 PUD ce7fc067 PMD 0
[  166.674230] Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
[  166.674230] CPU: 1 PID: 775 Comm: tc Not tainted 3.17.0-rc6+ #642
[  166.674230] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[  166.674230] task: ffff8800d03c4d20 ti: ffff8800cae7c000 task.ti: ffff8800cae7c000
[  166.674230] RIP: 0010:[<ffffffff814b739f>]  [<ffffffff814b739f>] __list_del_entry+0x5c/0x98
[  166.674230] RSP: 0018:ffff8800cae7f7d0  EFLAGS: 00010207
[  166.674230] RAX: 0000000000000000 RBX: ffff8800cba8d700 RCX: ffff8800cba8d700
[  166.674230] RDX: 0000000000000000 RSI: dead000000200200 RDI: ffff8800cba8d700
[  166.674230] RBP: ffff8800cae7f7d0 R08: 0000000000000001 R09: 0000000000000001
[  166.674230] R10: 0000000000000000 R11: 000000000000859a R12: ffffffffffffffe8
[  166.674230] R13: ffff8800cba8c5b8 R14: 0000000000000001 R15: ffff8800cba8d700
[  166.674230] FS:  00007fdb5f04a740(0000) GS:ffff88011a800000(0000) knlGS:0000000000000000
[  166.674230] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[  166.674230] CR2: 0000000000000000 CR3: 00000000cf929000 CR4: 00000000000006e0
[  166.674230] Stack:
[  166.674230]  ffff8800cae7f7e8 ffffffff814b73e8 ffff8800cba8d6e8 ffff8800cae7f828
[  166.674230]  ffffffff817caeec 0000000000000046 ffff8800cba8c5b0 ffff8800cba8c5b8
[  166.674230]  0000000000000000 0000000000000001 ffff8800cf8e33e8 ffff8800cae7f848
[  166.674230] Call Trace:
[  166.674230]  [<ffffffff814b73e8>] list_del+0xd/0x2b
[  166.674230]  [<ffffffff817caeec>] tcf_action_destroy+0x4c/0x71
[  166.674230]  [<ffffffff817ca0ce>] tcf_exts_destroy+0x20/0x2d
[  166.674230]  [<ffffffff817ec2b5>] tcindex_delete+0x196/0x1b7

struct list_head can not be simply copied and we should always init it.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>