- 06 Nov, 2015 40 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfdLinus Torvalds authored
Pull MFD updates from Lee Jones: "New Device Support: - Add support for 88pm860; 88pm80x - Add support for 24c08 EEPROM; at24 - Add support for Broxton Whiskey Cove; intel* - Add support for RTS522A; rts5227 - Add support for I2C devices; intel_quark_i2c_gpio New Functionality: - Add microphone support; arizona - Add general purpose switch support; arizona - Add fuel-gauge support; da9150-core - Add shutdown support; sec-core - Add charger support; tps65217 - Add flexible serial communication unit support; atmel-flexcom - Add power button support; axp20x - Add led-flash support; rt5033 Core Frameworks: - Supply a generic macro for defining Regmap IRQs - Rework ACPI child device matching Fix-ups: - Use Regmap to access registers; tps6105x - Use DEFINE_RES_IRQ_NAMED() macro; da9150 - Re-arrange device registration order; intel_quark_i2c_gpio - Allow OF matching; cros_ec_i2c, atmel-hlcdc, hi6421-pmic, max8997, sm501 - Handle deferred probe; twl6040 - Improve accuracy of headphone detect; arizona - Unnecessary MODULE_ALIAS() removal; bcm590xx, rt5033 - Remove unused code; htc-i2cpld, arizona, pcf50633-irq, sec-core - Simplify code; kempld, rts5209, da903x, lm3533, da9052, arizona - Remove #iffery; arizona - DT binding adaptions; many Bug Fixes: - Fix possible NULL pointer dereference; wm831x, tps6105x - Fix 64bit bug; intel_soc_pmic_bxtwc - Fix signedness issue; arizona" * tag 'mfd-for-linus-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (73 commits) bindings: mfd: s2mps11: Add documentation for s2mps15 PMIC mfd: sec-core: Remove unused s2mpu02-rtc and s2mpu02-clk children extcon: arizona: Add extcon specific device tree binding document MAINTAINERS: Add binding docs for Cirrus Logic/Wolfson Arizona devices mfd: arizona: Remove bindings covered in new subsystem specific docs mfd: rt5033: Add RT5033 Flash led sub device mfd: lpss: Add Intel Broxton PCI IDs mfd: lpss: Add Broxton ACPI IDs mfd: arizona: Signedness bug in arizona_runtime_suspend() mfd: axp20x: Add a cell for the power button part of the, axp288 PMICs mfd: dt-bindings: Document pulled down WRSTBI pin on S2MPS1X mfd: sec-core: Disable buck voltage reset on watchdog falling edge mfd: sec-core: Dump PMIC revision to find out the HW mfd: arizona: Use correct type ID for device tree config mfd: arizona: Remove use of codec build config #ifdefs mfd: arizona: Simplify adding subdevices mfd: arizona: Downgrade type mismatch messages to dev_warn mfd: arizona: Factor out checking of jack detection state mfd: arizona: Factor out DCVDD isolation control mfd: Make TPS6105X select REGMAP_I2C ...
-
Linus Torvalds authored
It turns out that we still have issues with the EFI memory map that ends up polluting our kernel page tables with writable executable pages. That will get sorted out, but in the meantime let's not make the scary complaint about them be on by default. The code is useful for developers, but not ready for end user testing yet. Acked-by:
Borislav Petkov <bp@alien8.de> Acked-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
Merge tag 'platform-drivers-x86-v4.4-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86 Pull x86 platform driver update from Darren Hart: "Various toshiba hotkey and keyboard related fixes and a new WMI driver. Several intel_scu_ipc cleanups and a locking fix. A spattering of small single fixes across various platforms. I was asked to pick up an OLPC cleanup as the driver appeared unmaintained and it seemed similar to what is maintained in platform/drivers/x86. I have included the patch and an update to the MAINTAINERS file. toshiba_acpi: - Initialize hotkey_event_type variable - Remove unneeded u32 variables from *setup_keyboard - Add 0x prefix to available_kbd_modes_show function - Change default Hotkey enabling value - Unify hotkey enabling functions toshiba-wmi: - Toshiba WMI Hotkey Driver intel_scu_ipc: - Protect dev member assignment on ->remove() - Switch to use module_pci_driver() macro - Convert to use struct device * - Propagate pointer to struct intel_scu_ipc_dev - Fix error path by turning to devm_* / pcim_* acer-wmi: - remove threeg and interface sysfs interfaces OLPC: - Use %*ph specifier instead of passing direct values MAINTAINERS: - Add drivers/platform/olpc to drivers/platform/x86 sony-laptop: - Fix handling sony_nc_hotkeys_decode result intel_mid_powerbtn: - Remove misuse of IRQF_NO_SUSPEND flag compal-laptop: - Add charge control limit asus-wmi: - restore kbd led level after resume" * tag 'platform-drivers-x86-v4.4-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: toshiba_acpi: Initialize hotkey_event_type variable intel_scu_ipc: Protect dev member assignment on ->remove() intel_scu_ipc: Switch to use module_pci_driver() macro intel_scu_ipc: Convert to use struct device * intel_scu_ipc: Propagate pointer to struct intel_scu_ipc_dev intel_scu_ipc: Fix error path by turning to devm_* / pcim_* acer-wmi: remove threeg and interface sysfs interfaces OLPC: Use %*ph specifier instead of passing direct values MAINTAINERS: Add drivers/platform/olpc to drivers/platform/x86 platform/x86: Toshiba WMI Hotkey Driver sony-laptop: Fix handling sony_nc_hotkeys_decode result intel_mid_powerbtn: Remove misuse of IRQF_NO_SUSPEND flag compal-laptop: Add charge control limit asus-wmi: restore kbd led level after resume toshiba_acpi: Remove unneeded u32 variables from *setup_keyboard toshiba_acpi: Add 0x prefix to available_kbd_modes_show function toshiba_acpi: Change default Hotkey enabling value toshiba_acpi: Unify hotkey enabling functions
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc updates from Michael Ellerman: - Kconfig: remove BE-only platforms from LE kernel build from Boqun Feng - Refresh ps3_defconfig from Geoff Levand - Emit GNU & SysV hashes for the vdso from Michael Ellerman - Define an enum for the bolted SLB indexes from Anshuman Khandual - Use a local to avoid multiple calls to get_slb_shadow() from Michael Ellerman - Add gettimeofday() benchmark from Michael Neuling - Avoid link stack corruption in __get_datapage() from Michael Neuling - Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar K.V - Add ppc64le_defconfig from Michael Ellerman - pseries: extract of_helpers module from Andy Shevchenko - Correct string length in pseries_of_derive_parent() from Nathan Fontenot - Free the MSI bitmap if it was slab allocated from Denis Kirjanov - Shorten irq_chip name for the SIU from Christophe Leroy - Wait 1s for secondaries to enter OPAL during kexec from Samuel Mendoza-Jonas - Fix _ALIGN_* errors due to type difference, from Aneesh Kumar K.V - powerpc/pseries/hvcserver: don't memset pi_buff if it is null from Colin Ian King - Disable hugepd for 64K page size, from Aneesh Kumar K.V - Differentiate between hugetlb and THP during page walk from Aneesh Kumar K.V - Make PCI non-optional for pseries from Michael Ellerman - Individual System V IPC system calls from Sam bobroff - Add selftest of unmuxed IPC calls from Michael Ellerman - discard .exit.data at runtime from Stephen Rothwell - Delete old orphaned PrPMC 280/2800 DTS and boot file, from Paul Gortmaker - Use of_get_next_parent to simplify code from Christophe Jaillet - Paginate some xmon output from Sam bobroff - Add some more elements to the xmon PACA dump from Michael Ellerman - Allow the tm-syscall selftest to build with old headers from Michael Ellerman - Run EBB selftests only on POWER8 from Denis Kirjanov - Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael Ellerman - Avoid reference to potentially freed memory in prom.c from Christophe Jaillet - Quieten boot wrapper output with run_cmd from Geoff Levand - EEH fixes and cleanups from Gavin Shan - Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan - Use of_get_next_parent() in of_get_ibm_chip_id() from Michael Ellerman - Fix section mismatch warning in msi_bitmap_alloc() from Denis Kirjanov - Fix ps3-lpm white space from Rudhresh Kumar J - Fix ps3-vuart null dereference from Colin King - nvram: Add missing kfree in error path from Christophe Jaillet - nvram: Fix function name in some errors messages, from Christophe Jaillet - drivers/macintosh: adb: fix misleading Kconfig help text from Aaro Koskinen - agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov - cxl: Free virtual PHB when removing from Andrew Donnellan - scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from Michael Ellerman - scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building with O= from Michael Ellerman - Freescale updates from Scott: Highlights include 64-bit book3e kexec/kdump support, a rework of the qoriq clock driver, device tree changes including qoriq fman nodes, support for a new 85xx board, and some fixes. - MPC5xxx updates from Anatolij: Highlights include a driver for MPC512x LocalPlus Bus FIFO with its device tree binding documentation, mpc512x device tree updates and some minor fixes. * tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (106 commits) powerpc/msi: Fix section mismatch warning in msi_bitmap_alloc() powerpc/prom: Use of_get_next_parent() in of_get_ibm_chip_id() powerpc/pseries: Correct string length in pseries_of_derive_parent() powerpc/e6500: hw tablewalk: make sure we invalidate and write to the same tlb entry powerpc/mpc85xx: Add FSL QorIQ DPAA FMan support to the SoC device tree(s) powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan powerpc/fsl: Add #clock-cells and clockgen label to clockgen nodes powerpc: handle error case in cpm_muram_alloc() powerpc: mpic: use IRQCHIP_SKIP_SET_WAKE instead of redundant mpic_irq_set_wake powerpc/book3e-64: Enable kexec powerpc/book3e-64/kexec: Set "r4 = 0" when entering spinloop powerpc/booke: Only use VIRT_PHYS_OFFSET on booke32 powerpc/book3e-64/kexec: Enable SMP release powerpc/book3e-64/kexec: create an identity TLB mapping powerpc/book3e-64: Don't limit paca to 256 MiB powerpc/book3e/kdump: Enable crash_kexec_wait_realmode powerpc/book3e: support CONFIG_RELOCATABLE powerpc/booke64: Fix args to copy_and_flush powerpc/book3e-64: rename interrupt_end_book3e with __end_interrupts powerpc/e6500: kexec: Handle hardware threads ...
-
Linus Torvalds authored
Merge patch-bomb from Andrew Morton: - inotify tweaks - some ocfs2 updates (many more are awaiting review) - various misc bits - kernel/watchdog.c updates - Some of mm. I have a huge number of MM patches this time and quite a lot of it is quite difficult and much will be held over to next time. * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (162 commits) selftests: vm: add tests for lock on fault mm: mlock: add mlock flags to enable VM_LOCKONFAULT usage mm: introduce VM_LOCKONFAULT mm: mlock: add new mlock system call mm: mlock: refactor mlock, munlock, and munlockall code kasan: always taint kernel on report mm, slub, kasan: enable user tracking by default with KASAN=y kasan: use IS_ALIGNED in memory_is_poisoned_8() kasan: Fix a type conversion error lib: test_kasan: add some testcases kasan: update reference to kasan prototype repo kasan: move KASAN_SANITIZE in arch/x86/boot/Makefile kasan: various fixes in documentation kasan: update log messages kasan: accurately determine the type of the bad access kasan: update reported bug types for kernel memory accesses kasan: update reported bug types for not user nor kernel memory accesses mm/kasan: prevent deadlock in kasan reporting mm/kasan: don't use kasan shadow pointer in generic functions mm/kasan: MODULE_VADDR is not available on all archs ...
-
Eric Biggers authored
This fixes a bug from commit f3f86e33 ("vfs: Fix pathological performance case for __alloc_fd()"). v2: refactor to share fd bitmap copying code Signed-off-by:
Eric Biggers <ebiggers3@gmail.com> Signed-off-by:
-
Eric B Munson authored
Test the mmap() flag, and the mlockall() flag. These tests ensure that pages are not faulted in until they are accessed, that the pages are unevictable once faulted in, and that VMA splitting and merging works with the new VM flag. The second test ensures that mlock limits are respected. Note that the limit test needs to be run a normal user. Also add tests to use the new mlock2 family of system calls. [treding@nvidia.com: : Fix mlock2-tests for 32-bit architectures] [treding@nvidia.com: ensure the mlock2 syscall number can be found] [treding@nvidia.com: use the right arguments for main()] Signed-off-by:
Eric B Munson <emunson@akamai.com> Cc: Shuah Khan <shuahkh@osg.samsung.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Eric B Munson authored
The previous patch introduced a flag that specified pages in a VMA should be placed on the unevictable LRU, but they should not be made present when the area is created. This patch adds the ability to set this state via the new mlock system calls. We add MLOCK_ONFAULT for mlock2 and MCL_ONFAULT for mlockall. MLOCK_ONFAULT will set the VM_LOCKONFAULT modifier for VM_LOCKED. MCL_ONFAULT should be used as a modifier to the two other mlockall flags. When used with MCL_CURRENT, all current mappings will be marked with VM_LOCKED | VM_LOCKONFAULT. When used with MCL_FUTURE, the mm->def_flags will be marked with VM_LOCKED | VM_LOCKONFAULT. When used with both MCL_CURRENT and MCL_FUTURE, all current mappings and mm->def_flags will be marked with VM_LOCKED | VM_LOCKONFAULT. Prior to this patch, mlockall() will unconditionally clear the mm->def_flags any time it is called without MCL_FUTURE. This behavior is maintained after adding MCL_ONFAULT. If a call to mlockall(MCL_FUTURE) is followed by mlockall(MCL_CURRENT), the mm->def_flags will be cleared and new VMAs will be unlocked. This remains true with or without MCL_ONFAULT in either mlockall() invocation. munlock() will unconditionally clear both vma flags. munlockall() unconditionally clears for VMA flags on all VMAs and in the mm->def_flags field. Signed-off-by:
Michal Hocko <mhocko@suse.com> Acked-by:
Vlastimil Babka <vbabka@suse.cz> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Shuah Khan <shuahkh@osg.samsung.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
Eric B Munson authored
The cost of faulting in all memory to be locked can be very high when working with large mappings. If only portions of the mapping will be used this can incur a high penalty for locking. For the example of a large file, this is the usage pattern for a large statical language model (probably applies to other statical or graphical models as well). For the security example, any application transacting in data that cannot be swapped out (credit card data, medical records, etc). This patch introduces the ability to request that pages are not pre-faulted, but are placed on the unevictable LRU when they are finally faulted in. The VM_LOCKONFAULT flag will be used together with VM_LOCKED and has no effect when set without VM_LOCKED. Setting the VM_LOCKONFAULT flag for a VMA will cause pages faulted into that VMA to be added to the unevictable LRU when they are faulted or if they are already present, but will not cause any missing pages to be faulted in. Exposing this new lock state means that we cannot overload the meaning of the FOLL_POPULATE flag any longer. Prior to this patch it was used to mean that the VMA for a fault was locked. This means we need the new FOLL_MLOCK flag to communicate the locked state of a VMA. FOLL_POPULATE will now only control if the VMA should be populated and in the case of VM_LOCKONFAULT, it will not be set. Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by:
-
Eric B Munson authored
With the refactored mlock code, introduce a new system call for mlock. The new call will allow the user to specify what lock states are being added. mlock2 is trivial at the moment, but a follow on patch will add a new mlock state making it useful. Signed-off-by:
-
Eric B Munson authored
mlock() allows a user to control page out of program memory, but this comes at the cost of faulting in the entire mapping when it is allocated. For large mappings where the entire area is not necessary this is not ideal. Instead of forcing all locked pages to be present when they are allocated, this set creates a middle ground. Pages are marked to be placed on the unevictable LRU (locked) when they are first used, but they are not faulted in by the mlock call. This series introduces a new mlock() system call that takes a flags argument along with the start address and size. This flags argument gives the caller the ability to request memory be locked in the traditional way, or to be locked after the page is faulted in. A new MCL flag is added to mirror the lock on fault behavior from mlock() in mlockall(). There are two main use cases that this set covers. The first is the security focussed mlock case. A buffer is needed that cannot be written to swap. The maximum size is known, but on average the memory used is significantly less than this maximum. With lock on fault, the buffer is guaranteed to never be paged out without consuming the maximum size every time such a buffer is created. The second use case is focussed on performance. Portions of a large file are needed and we want to keep the used portions in memory once accessed. This is the case for large graphical models where the path through the graph is not known until run time. The entire graph is unlikely to be used in a given invocation, but once a node has been used it needs to stay resident for further processing. Given these constraints we have a number of options. We can potentially waste a large amount of memory by mlocking the entire region (this can also cause a significant stall at startup as the entire file is read in). We can mlock every page as we access them without tracking if the page is already resident but this introduces large overhead for each access. The third option is mapping the entire region with PROT_NONE and using a signal handler for SIGSEGV to mprotect(PROT_READ) and mlock() the needed page. Doing this page at a time adds a significant performance penalty. Batching can be used to mitigate this overhead, but in order to safely avoid trying to mprotect pages outside of the mapping, the boundaries of each mapping to be used in this way must be tracked and available to the signal handler. This is precisely what the mm system in the kernel should already be doing. For mlock(MLOCK_ONFAULT) the user is charged against RLIMIT_MEMLOCK as if mlock(MLOCK_LOCKED) or mmap(MAP_LOCKED) was used, so when the VMA is created not when the pages are faulted in. For mlockall(MCL_ONFAULT) the user is charged as if MCL_FUTURE was used. This decision was made to keep the accounting checks out of the page fault path. To illustrate the benefit of this set I wrote a test program that mmaps a 5 GB file filled with random data and then makes 15,000,000 accesses to random addresses in that mapping. The test program was run 20 times for each setup. Results are reported for two program portions, setup and execution. The setup phase is calling mmap and optionally mlock on the entire region. For most experiments this is trivial, but it highlights the cost of faulting in the entire region. Results are averages across the 20 runs in milliseconds. mmap with mlock(MLOCK_LOCKED) on entire range: Setup avg: 8228.666 Processing avg: 8274.257 mmap with mlock(MLOCK_LOCKED) before each access: Setup avg: 0.113 Processing avg: 90993.552 mmap with PROT_NONE and signal handler and batch size of 1 page: With the default value in max_map_count, this gets ENOMEM as I attempt to change the permissions, after upping the sysctl significantly I get: Setup avg: 0.058 Processing avg: 69488.073 mmap with PROT_NONE and signal handler and batch size of 8 pages: Setup avg: 0.068 Processing avg: 38204.116 mmap with PROT_NONE and signal handler and batch size of 16 pages: Setup avg: 0.044 Processing avg: 29671.180 mmap with mlock(MLOCK_ONFAULT) on entire range: Setup avg: 0.189 Processing avg: 17904.899 The signal handler in the batch cases faulted in memory in two steps to avoid having to know the start and end of the faulting mapping. The first step covers the page that caused the fault as we know that it will be possible to lock. The second step speculatively tries to mlock and mprotect the batch size - 1 pages that follow. There may be a clever way to avoid this without having the program track each mapping to be covered by this handeler in a globally accessible structure, but I could not find it. It should be noted that with a large enough batch size this two step fault handler can still cause the program to crash if it reaches far beyond the end of the mapping. These results show that if the developer knows that a majority of the mapping will be used, it is better to try and fault it in at once, otherwise mlock(MLOCK_ONFAULT) is significantly faster. The performance cost of these patches are minimal on the two benchmarks I have tested (stream and kernbench). The following are the average values across 20 runs of stream and 10 runs of kernbench after a warmup run whose results were discarded. Avg throughput in MB/s from stream using 1000000 element arrays Test 4.2-rc1 4.2-rc1+lock-on-fault Copy: 10,566.5 10,421 Scale: 10,685 10,503.5 Add: 12,044.1 11,814.2 Triad: 12,064.8 11,846.3 Kernbench optimal load 4.2-rc1 4.2-rc1+lock-on-fault Elapsed Time 78.453 78.991 User Time 64.2395 65.2355 System Time 9.7335 9.7085 Context Switches 22211.5 22412.1 Sleeps 14965.3 14956.1 This patch (of 6): Extending the mlock system call is very difficult because it currently does not take a flags argument. A later patch in this set will extend mlock to support a middle ground between pages that are locked and faulted in immediately and unlocked pages. To pave the way for the new system call, the code needs some reorganization so that all the actual entry point handles is checking input and translating to VMA flags. Signed-off-by: -
Andrey Ryabinin authored
Currently we already taint the kernel in some cases. E.g. if we hit some bug in slub memory we call object_err() which will taint the kernel with TAINT_BAD_PAGE flag. But for other kind of bugs kernel left untainted. Always taint with TAINT_BAD_PAGE if kasan found some bug. This is useful for automated testing. Signed-off-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Reviewed-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Andrey Ryabinin authored
It's recommended to have slub's user tracking enabled with CONFIG_KASAN, because: a) User tracking disables slab merging which improves detecting out-of-bounds accesses. b) User tracking metadata acts as redzone which also improves detecting out-of-bounds accesses. c) User tracking provides additional information about object. This information helps to understand bugs. Currently it is not enabled by default. Besides recompiling the kernel with KASAN and reinstalling it, user also have to change the boot cmdline, which is not very handy. Enable slub user tracking by default with KASAN=y, since there is no good reason to not do this. [akpm@linux-foundation.org: little fixes, per David] Signed-off-by: -
Xishi Qiu authored
Use IS_ALIGNED() to determine whether the shadow span two bytes. It generates less code and more readable. Also add some comments in shadow check functions. Signed-off-by:
Xishi Qiu <qiuxishi@huawei.com> Acked-by:
-
Wang Long authored
The current KASAN code can not find the following out-of-bounds bugs: char *ptr; ptr = kmalloc(8, GFP_KERNEL); memset(ptr+7, 0, 2); the cause of the problem is the type conversion error in *memory_is_poisoned_n* function. So this patch fix that. Signed-off-by:Wang Long <long.wanglong@huawei.com> Acked-by:
-
Wang Long authored
Add some out of bounds testcases to test_kasan module. Signed-off-by:
-
Andrey Konovalov authored
Update the reference to the kasan prototype repository on github, since it was renamed. Signed-off-by:
Andrey Konovalov <andreyknvl@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Konstantin Serebryany <kcc@google.com> Signed-off-by:
-
Andrey Konovalov authored
Move KASAN_SANITIZE in arch/x86/boot/Makefile above the comment related to SVGA_MODE, since the comment refers to 'the next line'. Signed-off-by:
-
Andrey Konovalov authored
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by:
-
Andrey Konovalov authored
We decided to use KASAN as the short name of the tool and KernelAddressSanitizer as the full one. Update log messages according to that. Signed-off-by:
-
Andrey Konovalov authored
Makes KASAN accurately determine the type of the bad access. If the shadow byte value is in the [0, KASAN_SHADOW_SCALE_SIZE) range we can look at the next shadow byte to determine the type of the access. Signed-off-by:
-
Andrey Konovalov authored
Update the names of the bad access types to better reflect the type of the access that happended and make these error types "literals" that can be used for classification and deduplication in scripts. Signed-off-by:
-
Andrey Konovalov authored
Each access with address lower than kasan_shadow_to_mem(KASAN_SHADOW_START) is reported as user-memory-access. This is not always true, the accessed address might not be in user space. Fix this by reporting such accesses as null-ptr-derefs or wild-memory-accesses. There's another reason for this change. For userspace ASan we have a bunch of systems that analyze error types for the purpose of classification and deduplication. Sooner of later we will write them to KASAN as well. Then clearly and explicitly stated error types will bring value. Signed-off-by:
-
Aneesh Kumar K.V authored
When we end up calling kasan_report in real mode, our shadow mapping for the spinlock variable will show poisoned. This will result in us calling kasan_report_error with lock_report spin lock held. To prevent this disable kasan reporting when we are priting error w.r.t kasan. Signed-off-by:
Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Reviewed-by:
Andrey Ryabinin <ryabinin.a.a@gmail.com> Signed-off-by:
-
Aneesh Kumar K.V authored
We can't use generic functions like print_hex_dump to access kasan shadow region. This require us to setup another kasan shadow region for the address passed (kasan shadow address). Some architectures won't be able to do that. Hence make a copy of the shadow region row and pass that to generic functions. Signed-off-by:
-
Aneesh Kumar K.V authored
Use is_module_address instead Signed-off-by:
-
Aneesh Kumar K.V authored
The function only disable/enable reporting. In the later patch we will be adding a kasan early enable/disable. Rename kasan_enabled to properly reflect its function. Signed-off-by:
-
Tetsuo Handa authored
refresh_cpu_vm_stats(int cpu) is no longer referenced by !SMP kernel since Linux 3.12. Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by:
-
Hugh Dickins authored
There's an odd line about "Locked" at the head of the description of /proc/meminfo: it seems to have strayed from /proc/PID/smaps, so lead it back there. Move "Swap" and "SwapPss" descriptions down above it, to match the order in the file (though "PageSize"s still undescribed). The example of "Locked: 374 kB" (the same as Pss, neither Rss nor Size) is so unlikely as to be misleading: just make it 0, this is /bin/bash text; which would be "dw" (disabled write) not "de" (do not expand). Signed-off-by:
Hugh Dickins <hughd@google.com> Acked-by:
-
Hugh Dickins authored
LKP reports that v4.2 commit afa2db2f ("tmpfs: truncate prealloc blocks past i_size") causes a 14.5% slowdown in the AIM9 creat-clo benchmark. creat-clo does just what you'd expect from the name, and creat's O_TRUNC on 0-length file does indeed get into more overhead now shmem_setattr() tests "0 <= 0" instead of "0 < 0". I'm not sure how much we care, but I think it would not be too VW-like to add in a check for whether any pages (or swap) are allocated: if none are allocated, there's none to remove from the radix_tree. At first I thought that check would be good enough for the unmaps too, but no: we should not skip the unlikely case of unmapping pages beyond the new EOF, which were COWed from holes which have now been reclaimed, leaving none. This gives me an 8.5% speedup: on Haswell instead of LKP's Westmere, and running a debug config before and after: I hope those account for the lesser speedup. And probably someone has a benchmark where a thousand threads keep on stat'ing the same file repeatedly: forestall that report by adjusting v4.3 commit 44a30220 ("shmem: recalculate file inode when fstat") not to take the spinlock in shmem_getattr() when there's no work to do. Signed-off-by:
Ying Huang <ying.huang@linux.intel.com> Tested-by:
-
David Rientjes authored
/proc/pid/oom_adj exists solely to avoid breaking existing userspace binaries that write to the tunable. Add a comment in the only possible location within the kernel tree to describe the situation and motivation for keeping it around. Signed-off-by:
David Rientjes <rientjes@google.com> Signed-off-by:
-
Michal Hocko authored
Commit 424cdc14 ("memcg: convert threshold to bytes") has fixed a regression introduced by 3e32cb2e ("mm: memcontrol: lockless page counters") where thresholds were silently converted to use page units rather than bytes when interpreting the user input. The fix is not complete, though, as properly pointed out by Ben Hutchings during stable backport review. The page count is converted to bytes but unsigned long is used to hold the value which would be obviously not sufficient for 32b systems with more than 4G thresholds. The same applies to usage as taken from mem_cgroup_usage which might overflow. Let's remove this bytes vs. pages internal tracking differences and handle thresholds in page units internally. Chage mem_cgroup_usage() to return the value in page units and revert 424cdc14 because this should be sufficient for the consistent handling. mem_cgroup_read_u64 as the only users of mem_cgroup_usage outside of the threshold handling code is converted to give the proper in bytes result. It is doing that already for page_counter output so this is more consistent as well. The value presented to the userspace is still in bytes units. Fixes: 424cdc14 ("memcg: convert threshold to bytes") Fixes: 3e32cb2e ("mm: memcontrol: lockless page counters") Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Reviewed-by:
Vladimir Davydov <vdavydov@virtuozzo.com> Acked-by:
Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@vger.kernel.org> From: Michal Hocko <mhocko@kernel.org> Subject: memcg-fix-thresholds-for-32b-architectures-fix Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Vladimir Davydov <vdavydov@virtuozzo.com> Cc: Johannes Weiner <hannes@cmpxchg.org> From: Andrew Morton <akpm@linux-foundation.org> Subject: memcg-fix-thresholds-for-32b-architectures-fix-fix don't attempt to inline mem_cgroup_usage() The compiler ignores the inline anwyay. And __always_inlining it adds 600 bytes of goop to the .o file. Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Vladimir Davydov <vdavydov@virtuozzo.com> Signed-off-by:
-
Johannes Weiner authored
page_counter_try_charge() currently returns 0 on success and -ENOMEM on failure, which is surprising behavior given the function name. Make it follow the expected pattern of try_stuff() functions that return a boolean true to indicate success, or false for failure. Signed-off-by:
-
Johannes Weiner authored
memory.current on the root level doesn't add anything that wouldn't be more accurate and detailed using system statistics. It already doesn't include slabs, and it'll be a pain to keep in sync when further memory types are accounted in the memory controller. Remove it. Note that this applies to the new unified hierarchy interface only. Signed-off-by:
-
Dave Hansen authored
My recent patch "mm, hugetlb: use memory policy when available" added some bloat to hugetlb.o. This patch aims to get some of the bloat back, especially when NUMA is not in play. It does this with an implicit #ifdef and marking some things static that should have been static in my first patch. It also makes the warnings only VM_WARN_ON()s. They were responsible for a pretty big chunk of the bloat. Doing this gets our NUMA=n text size back to a wee bit _below_ where we started before the original patch. It also shaves a bit of space off the NUMA=y case, but not much. Enforcing the mempolicy definitely takes some text and it's hard to avoid. size(1) output: text data bss dec hex filename 30745 3433 2492 36670 8f3e hugetlb.o.nonuma.baseline 31305 3755 2492 37552 92b0 hugetlb.o.nonuma.patch1 30713 3433 2492 36638 8f1e hugetlb.o.nonuma.patch2 (this patch) 25235 473 41276 66984 105a8 hugetlb.o.numa.baseline 25715 475 41276 67466 1078a hugetlb.o.numa.patch1 25491 473 41276 67240 106a8 hugetlb.o.numa.patch2 (this patch) Signed-off-by:
Dave Hansen <dave.hansen@linux.intel.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by:
-
Dave Hansen authored
I have a hugetlbfs user which is never explicitly allocating huge pages with 'nr_hugepages'. They only set 'nr_overcommit_hugepages' and then let the pages be allocated from the buddy allocator at fault time. This works, but they noticed that mbind() was not doing them any good and the pages were being allocated without respect for the policy they specified. The code in question is this: > struct page *alloc_huge_page(struct vm_area_struct *vma, ... > page = dequeue_huge_page_vma(h, vma, addr, avoid_reserve, gbl_chg); > if (!page) { > page = alloc_buddy_huge_page(h, NUMA_NO_NODE); dequeue_huge_page_vma() is smart and will respect the VMA's memory policy. But, it only grabs _existing_ huge pages from the huge page pool. If the pool is empty, we fall back to alloc_buddy_huge_page() which obviously can't do anything with the VMA's policy because it isn't even passed the VMA. Almost everybody preallocates huge pages. That's probably why nobody has ever noticed this. Looking back at the git history, I don't think this _ever_ worked from when alloc_buddy_huge_page() was introduced in 7893d1d5, 8 years ago. The fix is to pass vma/addr down in to the places where we actually call in to the buddy allocator. It's fairly straightforward plumbing. This has been lightly tested. Signed-off-by: -
Alexander Kuleshov authored
There are no users of the node_hstates array outside of the mm/hugetlb.c. So let's make it static. Signed-off-by:
Alexander Kuleshov <kuleshovmail@gmail.com> Signed-off-by:
-
Rasmus Villemoes authored
As far as I can tell, strncpy_from_unsafe never returns -EFAULT. ret is the result of a __copy_from_user_inatomic(), which is 0 for success and positive (in this case necessarily 1) for access error - it is never negative. So we were always returning the length of the, possibly truncated, destination string. Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by:
Alexei Starovoitov <ast@kernel.org> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Namhyung Kim <namhyung@kernel.org> Signed-off-by:
-
Andrew Morton authored
mm/cma.c: In function 'cma_alloc': mm/cma.c:366: warning: 'pfn' may be used uninitialized in this function The patch actually improves the tracing a bit: if alloc_contig_range() fails, tracing will display the offending pfn rather than -1. Cc: Stefan Strogin <stefan.strogin@gmail.com> Cc: Michal Nazarewicz <mpn@google.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Cc: Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Hugh Dickins authored
clear_page_dirty_for_io() has accumulated writeback and memcg subtleties since v2.6.16 first introduced page migration; and the set_page_dirty() which completed its migration of PageDirty, later had to be moderated to __set_page_dirty_nobuffers(); then PageSwapBacked had to skip that too. No actual problems seen with this procedure recently, but if you look into what the clear_page_dirty_for_io(page)+set_page_dirty(newpage) is actually achieving, it turns out to be nothing more than moving the PageDirty flag, and its NR_FILE_DIRTY stat from one zone to another. It would be good to avoid a pile of irrelevant decrementations and incrementations, and improper event counting, and unnecessary descent of the radix_tree under tree_lock (to set the PAGECACHE_TAG_DIRTY which radix_tree_replace_slot() left in place anyway). Do the NR_FILE_DIRTY movement, like the other stats movements, while interrupts still disabled in migrate_page_move_mapping(); and don't even bother if the zone is the same. Do the PageDirty movement there under tree_lock too, where old page is frozen and newpage not yet visible: bearing in mind that as soon as newpage becomes visible in radix_tree, an un-page-locked set_page_dirty() might interfere (or perhaps that's just not possible: anything doing so should already hold an additional reference to the old page, preventing its migration; but play safe). But we do still need to transfer PageDirty in migrate_page_copy(), for those who don't go the mapping route through migrate_page_move_mapping(). Signed-off-by:
-
