- 09 Dec, 2017 39 commits
-
-
Florian Fainelli authored
[ Upstream commit bb7da333 ] Since we need to pad our packets, utilize skb_put_padto() which increases skb->len by how much we need to pad, allowing us to eliminate the test on skb->len right below. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Varun Prakash authored
[ Upstream commit a9a8cdb3 ] ip6_route_output() never returns NULL so check dst->error instead of !dst. Signed-off-by:
Varun Prakash <varun@chelsio.com> Signed-off-by:
-
Vincent Pelletier authored
[ Upstream commit 354bc45b ] Reserved1 is documented as expected to be set to 0, but this test fails when it it set to 0. Reverse the condition. Signed-off-by:
Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
M'boumba Cedric Madianga authored
[ Upstream commit 57b5a321 ] chan->desc is always set to NULL when a DMA transfer is complete. As a DMA transfer could be complete during the call of stm32_dma_tx_status, we need to be sure that chan->desc is not NULL before using this variable to avoid a null pointer deference issue. Signed-off-by:
M'boumba Cedric Madianga <cedric.madianga@gmail.com> Reviewed-by:
Ludovic BARRE <ludovic.barre@st.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
-
M'boumba Cedric Madianga authored
[ Upstream commit 7e96304d ] This patch sets the right number of arguments to be used for DMA clients which request channels from DT. Signed-off-by:
-
Guillaume Nault authored
[ Upstream commit a9b2dff8 ] For connected sockets, __l2tp_ip{,6}_bind_lookup() needs to check the remote IP when looking for a matching socket. Otherwise a connected socket can receive traffic not originating from its peer. Drop l2tp_ip_bind_lookup() and l2tp_ip6_bind_lookup() instead of updating their prototype, as these functions aren't used. Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
-
Slava Shwartsman authored
[ Upstream commit 61b6034c ] is_power_of_2 expects unsigned long and we pass u64 max_val_cycles, this will be truncated on 32 bit systems, and the result is not what we were expecting. div_u64 expects u32 as a second argument and we pass max_val_cycles_rounded which is u64 hence it will always be truncated. Fix was tested on both 64 and 32 bit systems and got same results for max_val_cycles and max_val_cycles_rounded. Fixes: 4850cf45 ("net/mlx4_en: Resolve dividing by zero in 32-bit system") Signed-off-by:
Slava Shwartsman <slavash@mellanox.com> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Jan Kara authored
[ Upstream commit e3fce68c ] Currently dax_iomap_rw() takes care of invalidating page tables and evicting hole pages from the radix tree when write(2) to the file happens. This invalidation is only necessary when there is some block allocation resulting from write(2). Furthermore in current place the invalidation is racy wrt page fault instantiating a hole page just after we have invalidated it. So perform the page invalidation inside dax_iomap_actor() where we can do it only when really necessary and after blocks have been allocated so nobody will be instantiating new hole pages anymore. Reviewed-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Ladislav Michl authored
[ Upstream commit fe895ac8 ] As user's guide "ADS1015EVM, ADS1115EVM, ADS1015EVM-PDK, ADS1115EVM-PDK User Guide (Rev. B)" (http://www.ti.com/lit/ug/sbau157b/sbau157b.pdf) states at page 16: "Note that both the ADS1115 and ADS1015 have internal clocks with a ±10% accuracy. If performing FFT tests, frequencies may appear to be incorrect as a result of this tolerance range.", add those 10% to converion wait time. Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by:
Ladislav Michl <ladis@linux-mips.org> Reviewed-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Arnaldo Carvalho de Melo authored
[ Upstream commit 6ae8eefc ] LIST_POISON[12] are used to initialize list_head and hlist_node pointers, and do void pointer arithmetic, which C++ doesn't like, so, to avoid drifting from the kernel by introducing some HLIST_POISON to do away with void pointer math, just make those poisoned pointers be NULL when building it with a C++ compiler. Noticed with: $ make LLVM_CONFIG=/usr/bin/llvm-config-3.9 LIBCLANGLLVM=1 CXX util/c++/clang.o CXX util/c++/clang-test.o In file included from /home/lizj/linux/tools/include/linux/list.h:5:0, from /home/lizj/linux/tools/perf/util/namespaces.h:13, from /home/lizj/linux/tools/perf/util/util.h:15, from /home/lizj/linux/tools/perf/util/util-cxx.h:20, from util/c++/clang-c.h:5, from util/c++/clang-test.cpp:2: /home/lizj/linux/tools/include/linux/list.h: In function ‘void list_del(list_head*)’: /home/lizj/linux/tools/include/linux/poison.h:14:31: error: pointer of type ‘void *’ used in arithmetic [-Werror=pointer-arith] # define POISON_POINTER_DELTA 0 ^ /home/lizj/linux/tools/include/linux/poison.h:22:41: note: in expansion of macro ‘POISON_POINTER_DELTA’ #define LIST_POISON1 ((void *) 0x100 + POISON_POINTER_DELTA) ^ /home/lizj/linux/tools/include/linux/list.h:107:16: note: in expansion of macro ‘LIST_POISON1’ entry->next = LIST_POISON1; ^ In file included from /home/lizj/linux/tools/perf/util/namespaces.h:13:0, from /home/lizj/linux/tools/perf/util/util.h:15, from /home/lizj/linux/tools/perf/util/util-cxx.h:20, from util/c++/clang-c.h:5, from util/c++/clang-test.cpp:2: /home/lizj/linux/tools/include/linux/list.h:107:14: error: invalid conversion from ‘void*’ to ‘list_head*’ [-fpermissive] Reported-by:
Li Zhijian <lizhijian@cn.fujitsu.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Philip Li <philip.li@intel.com> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/n/tip-m5ei2o0mjshucbr28baf5lqz@git.kernel.orgSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Masami Hiramatsu authored
[ Upstream commit 5bb4fc2d ] Disable preemption in ftrace-based jprobe handlers as described in Documentation/kprobes.txt: "Probe handlers are run with preemption disabled." This will fix jprobes behavior when CONFIG_PREEMPT=y. Signed-off-by:
Masami Hiramatsu <mhiramat@kernel.org> Cc: Alexei Starovoitov <ast@fb.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/150581530024.32348.9863783558598926771.stgit@devboxSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Thomas Richter authored
[ Upstream commit 22905582 ] Command perf test -v 16 (Setup struct perf_event_attr test) always reports success even if the test case fails. It works correctly if you also specify -F (for don't fork). root@s35lp76 perf]# ./perf test -v 16 15: Setup struct perf_event_attr : --- start --- running './tests/attr/test-record-no-delay' [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.002 MB /tmp/tmp4E1h7R/perf.data (1 samples) ] expected task=0, got 1 expected precise_ip=0, got 3 expected wakeup_events=1, got 0 FAILED './tests/attr/test-record-no-delay' - match failure test child finished with 0 ---- end ---- Setup struct perf_event_attr: Ok The reason for the wrong error reporting is the return value of the system() library call. It is called in run_dir() file tests/attr.c and returns the exit status, in above case 0xff00. This value is given as parameter to the exit() function which can only handle values 0-0xff. The child process terminates with exit value of 0 and the parent does not detect any error. This patch corrects the error reporting and prints the correct test result. Signed-off-by:
Thomas-Mich Richter <tmricht@linux.vnet.ibm.com> Acked-by:
Jiri Olsa <jolsa@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com> LPU-Reference: 20170913081209.39570-2-tmricht@linux.vnet.ibm.com Link: http://lkml.kernel.org/n/tip-rdube6rfcjsr1nzue72c7lqn@git.kernel.orgSigned-off-by:
-
Ben Hutchings authored
[ Upstream commit c15562c0 ] usbip_host_driver.h now depends on several additional headers, which need to be installed along with it. Fixes: 021aed84 ("staging: usbip: userspace: migrate usbip_host_driver ...") Fixes: 3391ba0e ("usbip: tools: Extract generic code to be shared with ...") Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Acked-by:
Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by:
-
Jibin Xu authored
[ Upstream commit b00bebbc ] When kernel configuration SMP,PREEMPT and DEBUG_PREEMPT are enabled, echo 1 >/proc/sys/kernel/sysrq echo p >/proc/sysrq-trigger kernel will print call trace as below: sysrq: SysRq : Show Regs BUG: using __this_cpu_read() in preemptible [00000000] code: sh/435 caller is __this_cpu_preempt_check+0x18/0x20 Call trace: [<ffffff8008088e80>] dump_backtrace+0x0/0x1d0 [<ffffff8008089074>] show_stack+0x24/0x30 [<ffffff8008447970>] dump_stack+0x90/0xb0 [<ffffff8008463950>] check_preemption_disabled+0x100/0x108 [<ffffff8008463998>] __this_cpu_preempt_check+0x18/0x20 [<ffffff80084c9194>] sysrq_handle_showregs+0x1c/0x40 [<ffffff80084c9c7c>] __handle_sysrq+0x12c/0x1a0 [<ffffff80084ca140>] write_sysrq_trigger+0x60/0x70 [<ffffff8008251e00>] proc_reg_write+0x90/0xd0 [<ffffff80081f1788>] __vfs_write+0x48/0x90 [<ffffff80081f241c>] vfs_write+0xa4/0x190 [<ffffff80081f3354>] SyS_write+0x54/0xb0 [<ffffff80080833f0>] el0_svc_naked+0x24/0x28 This can be seen on a common board like an r-pi3. This happens because when echo p >/proc/sysrq-trigger, get_irq_regs() is called outside of IRQ context, if preemption is enabled in this situation,kernel will print the call trace. Since many prior discussions on the mailing lists have made it clear that get_irq_regs either just returns NULL or stale data when used outside of IRQ context,we simply avoid calling it outside of IRQ context. Signed-off-by:
Jibin Xu <jibin.xu@windriver.com> Signed-off-by:
-
Gustavo A. R. Silva authored
[ Upstream commit a8e9b186 ] Add missing break statement in order to prevent the code from falling through. Signed-off-by:
Gustavo A. R. Silva <garsilva@embeddedor.com> Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/20171016174029.GA19757@embeddedor.comSigned-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
-
Dave Hansen authored
[ Upstream commit da20ab35 ] We do not have tracepoints for sys_modify_ldt() because we define it directly instead of using the normal SYSCALL_DEFINEx() macros. However, there is a reason sys_modify_ldt() does not use the macros: it has an 'int' return type instead of 'unsigned long'. This is a bug, but it's a bug cemented in the ABI. What does this mean? If we return -EINVAL from a function that returns 'int', we have 0x00000000ffffffea in %rax. But, if we return -EINVAL from a function returning 'unsigned long', we end up with 0xffffffffffffffea in %rax, which is wrong. To work around this and maintain the 'int' behavior while using the SYSCALL_DEFINEx() macros, so we add a cast to 'unsigned int' in both implementations of sys_modify_ldt(). Signed-off-by:
Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by:
Andy Lutomirski <luto@kernel.org> Reviewed-by:
Brian Gerst <brgerst@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20171018172107.1A79C532@viggo.jf.intel.comSigned-off-by:
-
Aaron Sierra authored
[ Upstream commit 0ab84da2 ] The upper four bits of the XR17V35x fractional divisor register (DLD) control general chip function (RS-485 direction pin polarity, multidrop mode, XON/XOFF parity check, and fast IR mode). Don't allow these bits to be clobbered when setting the baudrate. Signed-off-by:
Aaron Sierra <asierra@xes-inc.com> Signed-off-by:
-
Alexey Khoroshilov authored
[ Upstream commit ce035409 ] If devm_extcon_dev_allocate() fails, we should disable clk before return. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Fixes: 860d2686 ("usb: phy: tahvo: Use devm_extcon_dev_[allocate|register]() and replace deprecated API") Signed-off-by:
-
Subhash Jadavani authored
[ Upstream commit c7ccee22 ] SDCC controller reset (SW_RST) during probe may trigger power irq if previous status of PWRCTL was either BUS_ON or IO_HIGH_V. So before we enable the power irq interrupt in GIC (by registering the interrupt handler), we need to ensure that any pending power irq interrupt status is acknowledged otherwise power irq interrupt handler would be fired prematurely. Signed-off-by:
Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by:
Vijay Viswanath <vviswana@codeaurora.org> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Johan Hovold authored
[ Upstream commit 4d5e0689 ] Take an extra reference to the controller before deregistering it to prevent use-after-free in the interrupt handler in case an interrupt fires before the line is disabled. Fixes: b1353d1c ("spi: Add Analog Devices AXI SPI Engine controller support") Acked-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Hiromitsu Yamasaki authored
[ Upstream commit 36735783 ] DMA supports 32-bit words only, even if BITLEN1 of SITMDR2 register is 16bit. Fixes: b0d0ce8b ("spi: sh-msiof: Add DMA support") Signed-off-by:
Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com> Signed-off-by:
Simon Horman <horms+renesas@verge.net.au> Acked-by:
Geert Uytterhoeven <geert+renesas@glider.be> Acked-by:
Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by:
-
Colin Ian King authored
[ Upstream commit 123c0aab ] There is a check on pmlmepriv before dereferencing it when vfree'ing pmlmepriv->free_bss_buf however the previous call to rtw_free_mlme_priv_ie_data deferences pmlmepriv causing a null pointer deference if it is null. Avoid this by also calling rtw_free_mlme_priv_ie_data if the pointer is non-null. Detected by CoverityScan, CID#1230262 ("Dereference before null check") Fixes: 7b464c9f ("staging: r8188eu: Add files for new driver - part 4") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Lukas Wunner authored
[ Upstream commit 3236a965 ] This driver's ->rs485_config callback checks if SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND have the same value. If they do, it means the user has passed in invalid data with the TIOCSRS485 ioctl() since RTS must have a different polarity when sending and when not sending. In this case, rs485 mode is not enabled (the RS485_URA bit is not set in the RS485 Enable Register) and this is supposed to be signaled back to the user by clearing the SER_RS485_ENABLED bit in struct serial_rs485 ... except a missing tilde character is preventing that from happening. Fixes: 28e3fb6c ("serial: Add support for Fintek F81216A LPC to 4 UART") Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com> Signed-off-by:
Lukas Wunner <lukas@wunner.de> Signed-off-by:
-
Greg Ungerer authored
[ Upstream commit f55ab8f2 ] The m68k pg_data_table is a fix size array defined in arch/m68k/mm/init.c. Index numbers within it are defined based on memory size. But for Coldfire these don't take into account a non-zero physical RAM base address, and this causes us to access past the end of this array at system start time. Change the node shift calculation so that we keep the index inside its range. Reported-by:
Angelo Dureghello <angelo@sysam.it> Tested-by:
Greg Ungerer <gerg@linux-m68k.org> Signed-off-by:
-
Bryan O'Donoghue authored
[ Upstream commit 44b02da3 ] Commit 12927835 ("greybus: loopback: Add asynchronous bi-directional support") does what it says on the tin - namely, adds support for asynchronous bi-directional loopback operations. What it neglects to do though is increment the per-connection gb->iteration_count on an asynchronous operation error. This patch fixes that omission. Fixes: 12927835 ("greybus: loopback: Add asynchronous bi-directional support") Signed-off-by:
Bryan O'Donoghue <pure.logic@nexus-software.ie> Reported-by:
Mitch Tasman <tasman@leaflabs.com> Reviewed-by:
-
Andy Lutomirski authored
[ Upstream commit fec8f5ae ] We weren't testing the .limit and .limit_in_pages fields very well. Add more tests. This addition seems to trigger the "bits 16:19 are undefined" issue that was fixed in an earlier patch. I think that, at least on my CPU, the high nibble of the limit ends in LAR bits 16:19. Signed-off-by:
-
Christian Borntraeger authored
[ Upstream commit 48070c73 ] As of today QEMU does not provide the AIS facility to its guest. This prevents Linux guests from using PCI devices as the ais facility is checked during init. As this is just a performance optimization, we can move the ais check into the code where we need it (calling the SIC instruction). This is used at initialization and on interrupt. Both places do not require any serialization, so we can simply skip the instruction. Since we will now get all interrupts, we can also avoid the 2nd scan. As we can have multiple interrupts in parallel we might trigger spurious irqs more often for the non-AIS case but the core code can handle that. Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by:
Pierre Morel <pmorel@linux.vnet.ibm.com> Reviewed-by:
Halil Pasic <pasic@linux.vnet.ibm.com> Acked-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
-
Boshi Wang authored
[ Upstream commit ebe7c0a7 ] The hash_setup function always sets the hash_setup_done flag, even when the hash algorithm is invalid. This prevents the default hash algorithm defined as CONFIG_IMA_DEFAULT_HASH from being used. This patch sets hash_setup_done flag only for valid hash algorithms. Fixes: e7a2ad7e "ima: enable support for larger default filedata hash algorithms" Signed-off-by:
Boshi Wang <wangboshi@huawei.com> Signed-off-by:
Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by:
-
Sebastian Sjoholm authored
commit c654b21e upstream. Quectel BG96 is an Qualcomm MDM9206 based IoT modem, supporting both CAT-M and NB-IoT. Tested hardware is BG96 mounted on Quectel development board (EVB). The USB id is added to option.c to allow DIAG,GPS,AT and modem communication with the BG96. Signed-off-by:
Sebastian Sjoholm <ssjoholm@mac.com> Signed-off-by:
-
Heiko Carstens authored
commit 8d9047f8 upstream. Free data structures required for runtime instrumentation from arch_release_task_struct(). This allows to simplify the code a bit, and also makes the semantics a bit easier: arch_release_task_struct() is never called from the task that is being removed. In addition this allows to get rid of exit_thread() in a later patch. Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Matt Wilson authored
commit 3bfd1300 upstream. This device will be used in future Amazon EC2 instances as the primary serial port (i.e., data sent to this port will be available via the GetConsoleOuput [1] EC2 API). [1] http://docs.aws.amazon.com/AWSEC2/latest/APIReference/API_GetConsoleOutput.htmlSigned-off-by:
Matt Wilson <msw@amazon.com> Signed-off-by:
-
Kai-Heng Feng authored
commit e43a12f1 upstream. KY-688 USB 3.1 Type-C Hub internally uses a Genesys Logic hub to connect to Realtek r8153. Similar to commit ("7496cfe5 usb: quirks: Add no-lpm quirk for Moshi USB to Ethernet Adapter"), no-lpm can make r8153 ethernet work. Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
-
Hans de Goede authored
commit 7fee72d5 upstream. We've been adding this as a quirk on a per device basis hoping that newer disk enclosures would do better, but that has not happened, so simply apply this quirk to all Seagate devices. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Wang Nan authored
commit 687cb088 upstream. tlb_gather_mmu(&tlb, mm, 0, -1) means gathering the whole virtual memory space. In this case, tlb->fullmm is true. Some archs like arm64 doesn't flush TLB when tlb->fullmm is true: commit 5a7862e8 ("arm64: tlbflush: avoid flushing when fullmm == 1"). Which causes leaking of tlb entries. Will clarifies his patch: "Basically, we tag each address space with an ASID (PCID on x86) which is resident in the TLB. This means we can elide TLB invalidation when pulling down a full mm because we won't ever assign that ASID to another mm without doing TLB invalidation elsewhere (which actually just nukes the whole TLB). I think that means that we could potentially not fault on a kernel uaccess, because we could hit in the TLB" There could be a window between complete_signal() sending IPI to other cores and all threads sharing this mm are really kicked off from cores. In this window, the oom reaper may calls tlb_flush_mmu_tlbonly() to flush TLB then frees pages. However, due to the above problem, the TLB entries are not really flushed on arm64. Other threads are possible to access these pages through TLB entries. Moreover, a copy_to_user() can also write to these pages without generating page fault, causes use-after-free bugs. This patch gathers each vma instead of gathering full vm space. In this case tlb->fullmm is not true. The behavior of oom reaper become similar to munmapping before do_exit, which should be safe for all archs. Link: http://lkml.kernel.org/r/20171107095453.179940-1-wangnan0@huawei.com Fixes: aac45363 ("mm, oom: introduce oom reaper") Signed-off-by:
Wang Nan <wangnan0@huawei.com> Acked-by:
Michal Hocko <mhocko@suse.com> Acked-by:
David Rientjes <rientjes@google.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Bob Liu <liubo95@huawei.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Roman Gushchin <guro@fb.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> [backported to 4.9 stable tree] Signed-off-by:
-
Horia Geantă authored
commit 2b163b5b upstream. This reverts commit 66d2e202. Quoting from Russell's findings: https://www.mail-archive.com/linux-crypto@vger.kernel.org/msg21136.html [quote] Okay, I've re-tested, using a different way of measuring, because using openssl speed is impractical for off-loaded engines. I've decided to use this way to measure the performance: dd if=/dev/zero bs=1048576 count=128 | /usr/bin/time openssl dgst -md5 For the threaded IRQs case gives: 0.05user 2.74system 0:05.30elapsed 52%CPU (0avgtext+0avgdata 2400maxresident)k 0.06user 2.52system 0:05.18elapsed 49%CPU (0avgtext+0avgdata 2404maxresident)k 0.12user 2.60system 0:05.61elapsed 48%CPU (0avgtext+0avgdata 2460maxresident)k => 5.36s => 25.0MB/s and the tasklet case: 0.08user 2.53system 0:04.83elapsed 54%CPU (0avgtext+0avgdata 2468maxresident)k 0.09user 2.47system 0:05.16elapsed 49%CPU (0avgtext+0avgdata 2368maxresident)k 0.10user 2.51system 0:04.87elapsed 53%CPU (0avgtext+0avgdata 2460maxresident)k => 4.95 => 27.1MB/s which corresponds to an 8% slowdown for the threaded IRQ case. So, tasklets are indeed faster than threaded IRQs. [...] I think I've proven from the above that this patch needs to be reverted due to the performance regression, and that there _is_ most definitely a deterimental effect of switching from tasklets to threaded IRQs. [/quote] Signed-off-by:
Horia Geantă <horia.geanta@nxp.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Stefan Agner authored
commit 9fd99f4f upstream. The resume helpers wait for a vblank to occurre hence IRQ need to be enabled. This avoids a warning as follows during resume: WARNING: CPU: 0 PID: 314 at drivers/gpu/drm/drm_atomic_helper.c:1249 drm_atomic_helper_wait_for_vblanks.part.1+0x284/0x288 [CRTC:28:crtc-0] vblank wait timed out Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
-
Stefan Agner authored
commit 9306e996 upstream. With commit 0a70c998 ("drm/fsl-dcu: enable pixel clock when enabling CRTC") the pixel clock is controlled by the CRTC code. Disabling the pixel clock in suspend leads to a warning due to the second clk_disable_unprepare call: WARNING: CPU: 0 PID: 359 at drivers/clk/clk.c:594 clk_core_disable+0x8c/0x90 Remove clk_disable_unprepare call for pixel clock to avoid unbalanced clock disable on suspend. Fixes: 0a70c998 ("drm/fsl-dcu: enable pixel clock when enabling CRTC") Signed-off-by:
-
Rui Hua authored
commit e393aa24 upstream. When we send a read request and hit the clean data in cache device, there is a situation called cache read race in bcache(see the commit in the tail of cache_look_up(), the following explaination just copy from there): The bucket we're reading from might be reused while our bio is in flight, and we could then end up reading the wrong data. We guard against this by checking (in bch_cache_read_endio()) if the pointer is stale again; if so, we treat it as an error (s->iop.error = -EINTR) and reread from the backing device (but we don't pass that error up anywhere) It should be noted that cache read race happened under normal circumstances, not the circumstance when SSD failed, it was counted and shown in /sys/fs/bcache/XXX/internal/cache_read_races. Without this patch, when we use writeback mode, we will never reread from the backing device when cache read race happened, until the whole cache device is clean, because the condition (s->recoverable && (dc && !atomic_read(&dc->has_dirty))) is false in cached_dev_read_error(). In this situation, the s->iop.error(= -EINTR) will be passed up, at last, user will receive -EINTR when it's bio end, this is not suitable, and wield to up-application. In this patch, we use s->read_dirty_data to judge whether the read request hit dirty data in cache device, it is safe to reread data from the backing device when the read request hit clean data. This can not only handle cache read race, but also recover data when failed read request from cache device. [edited by mlyle to fix up whitespace, commit log title, comment spelling] Fixes: d59b2379 ("bcache: only permit to recovery read error when cache device is clean") Signed-off-by:
Hua Rui <huarui.dev@gmail.com> Reviewed-by:
Michael Lyle <mlyle@lyle.org> Reviewed-by:
Coly Li <colyli@suse.de> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Coly Li authored
commit d59b2379 upstream. When bcache does read I/Os, for example in writeback or writethrough mode, if a read request on cache device is failed, bcache will try to recovery the request by reading from cached device. If the data on cached device is not synced with cache device, then requester will get a stale data. For critical storage system like database, providing stale data from recovery may result an application level data corruption, which is unacceptible. With this patch, for a failed read request in writeback or writethrough mode, recovery a recoverable read request only happens when cache device is clean. That is to say, all data on cached device is up to update. For other cache modes in bcache, read request will never hit cached_dev_read_error(), they don't need this patch. Please note, because cache mode can be switched arbitrarily in run time, a writethrough mode might be switched from a writeback mode. Therefore checking dc->has_data in writethrough mode still makes sense. Changelog: V4: Fix parens error pointed by Michael Lyle. v3: By response from Kent Oversteet, he thinks recovering stale data is a bug to fix, and option to permit it is unnecessary. So this version the sysfs file is removed. v2: rename sysfs entry from allow_stale_data_on_failure to allow_stale_data_on_failure, and fix the confusing commit log. v1: initial patch posted. [small change to patch comment spelling by mlyle] Signed-off-by:
Arne Wolf <awolf@lenovo.com> Reviewed-by:
-
- 05 Dec, 2017 1 commit
-
-
Greg Kroah-Hartman authored
-
