With commit 34d21de9 ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of this driver.

With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.

Remove the allocation in the vsockmon driver and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20240223115839.3572852-1-leitao@debian.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Serge Semin says:

====================
net: pcs: xpcs: Cleanups before adding MMIO dev support

As stated in the subject this series is a short prequel before submitting
the main patches adding the memory-mapped DW XPCS support to the DW XPCS
and DW *MAC (STMMAC) drivers. Originally it was a part of the bigger
patchset (see the changelog v2 link below) but was detached to a
preparation set to shrink down the main series thus simplifying it'
review.

The patchset' content is straightforward: drop the redundant sentinel
entry and the header files; return EINVAL errno from the soft-reset method
and make sure that the interface validation method return EINVAL straight
away if the requested interface isn't supported by the XPCS device
instance. All of these changes are required to simplify the changes being
introduced a bit later in the framework of the memory-mapped DW XPCS
support patches.

Link: https://lore.kernel.org/netdev/20231205103559.9605-1-fancer.lancer@gmail.com
Changelog v2:
- Move the preparation patches to a separate series.
- Simplify the commit messages (@Russell, @Vladimir).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If an unsupported interface is passed to the PCS validation callback there
is no need in further link-modes calculations since the resultant array
will be initialized with zeros which will be perceived by the phylink
subsystem as error anyway (see phylink_validate_mac_and_pcs()). Instead
let's explicitly return the -EINVAL error to inform the caller about the
unsupported interface as it's done in the rest of the pcs_validate
callbacks.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In particular the xpcs_soft_reset() and xpcs_do_config() functions
currently return -1 if invalid auto-negotiation mode is specified. That
value might be then passed to the generic kernel subsystems which require
a standard kernel errno value. Even though the erroneous conditions are
very specific (memory corruption or buggy driver implementation) using a
hard-coded -1 literal doesn't seem correct anyway especially when it comes
to passing it higher to the network subsystem or printing to the system
log.  Convert the hard-coded error values to -EINVAL then.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is nothing CM workqueue-related in the driver. So the respective
include directive can be dropped.

While at it add an empty line delimiter between the generic and local path
include directives to visually separate them.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are currently only two methods (xpcs_find_compat() and
xpcs_get_interfaces()) defined in the driver which loop over the available
interfaces. All of them rely on the xpcs_compat::num_interfaces field
value to get the total number of supported interfaces. Thus the interface
arrays are supposed to be filled with actual interface IDs and there is no
need in the dummy terminating ID placed at the end of the arrays.

Based on the above drop the PHY_INTERFACE_MODE_MAX entry from the
xpcs_2500basex_interfaces array and the PHY_INTERFACE_MODE_MAX-based
conditional statement from the xpcs_get_interfaces() method as redundant.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
rtnetlink: reduce RTNL pressure for dumps

This series restarts the conversion of rtnl dump operations
to RCU protection, instead of requiring RTNL.

In this new attempt (prior one failed in 2011), I chose to
allow a gradual conversion of selected operations.

After this series, "ip -6 addr" and "ip -4 ro" no longer
need to acquire RTNL.

I refrained from changing inet_dump_ifaddr() and inet6_dump_addr()
to avoid merge conflicts because of two fixes in net tree.

I also started the work for "ip link" future conversion.

v2: rtnl_fill_link_ifmap() always emit IFLA_MAP (Jiri Pirko)
    Added "nexthop: allow nexthop_mpath_fill_node()
           to be called without RTNL" to avoid a lockdep splat (Ido Schimmel)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We want to be able to run rtnl_fill_ifinfo() under RCU protection
instead of RTNL in the future.

dev->name_node items are already rcu protected.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use READ_ONCE() to read the following device fields:

	dev->mem_start
	dev->mem_end
	dev->base_addr
	dev->irq
	dev->dma
	dev->if_port
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No longer hold RTNL while calling inet_dump_fib().

Also change return value for a completed dump:

Returning 0 instead of skb->len allows NLMSG_DONE
to be appended to the skb. User space does not have
to call us again to get a standalone NLMSG_DONE marker.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nexthop_mpath_fill_node() will be potentially called
from contexts holding rcu_lock instead of RTNL.
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/all/ZdZDWVdjMaQkXBgW@shredder/Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new field into struct fib_dump_filter, to let callers
tell if they use RTNL locking or RCU.

This is used in the following patch, when inet_dump_fib()
no longer holds RTNL.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No longer hold RTNL while calling inet6_dump_ifinfo()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similarly to RTNL_FLAG_DOIT_UNLOCKED, this new flag
allows dump operations registered via rtnl_register()
or rtnl_register_module() to opt-out from RTNL protection.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit af65bdfc ("[NETLINK]: Switch cb_lock spinlock
to mutex and allow to override it"), Patrick McHardy used
a common mutex to protect both nlk->cb and the dump() operations.

The override is used for rtnl dumps, registered with
rntl_register() and rntl_register_module().

We want to be able to opt-out some dump() operations
to not acquire RTNL, so we need to protect nlk->cb
with a per socket mutex.

This patch renames nlk->cb_def_mutex to nlk->nl_cb_mutex

The optional pointer to the mutex used to protect dump()
call is stored in nlk->dump_cb_mutex
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__netlink_dump_start() releases nlk->cb_mutex right before
calling netlink_dump() which grabs it again.

This seems dangerous, even if KASAN did not bother yet.

Add a @lock_taken parameter to netlink_dump() to let it
grab the mutex if called from netlink_recvmsg() only.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__netlink_diag_dump() returns 1 if the dump is not complete,
zero if no error occurred.

If err variable is zero, this means the dump is complete:
We should not return skb->len in this case, but 0.

This allows NLMSG_DONE to be appended to the skb.
User space does not have to call us again only to get NLMSG_DONE.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prepare inet6_dump_ifinfo() to run with RCU protection
instead of RTNL and use for_each_netdev_dump() interface.

Also properly return 0 at the end of a dump, avoiding
an extra recvmsg() system call and RTNL acquisition.

Note that RTNL-less dumps need core changes, coming later
in the series.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We want to use RCU protection instead of RTNL
for inet6_fill_ifinfo().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We want to no longer hold RTNL while calling inet6_fill_ifla6_attrs()
in the future. Add needed READ_ONCE()/WRITE_ONCE() annotations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We want to be able to run rtnl_fill_ifinfo() under RCU protection
instead of RTNL in the future.

This patch prepares dev_get_iflink() and nla_put_iflink()
to run either with RTNL or RCU held.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jérémie Dautheribes says:

====================
Add support for TI DP83826 configuration

This short patch series introduces the possibility of overriding
some parameters which are latched by default by hardware straps on the
TI DP83826 PHY.

The settings that can be overridden include:
  - Configuring the PHY in either MII mode or RMII mode.
  - When in RMII mode, configuring the PHY in RMII slave mode or RMII
  master mode.

The RMII master/slave mode is TI-specific and determines whether the PHY
operates from a 25MHz reference clock (master mode) or from a 50MHz
reference clock (slave mode).

While these features should be supported by all the TI DP8382x family,
I have only been able to test them on TI DP83826 hardware.  Therefore,
support has been added specifically for this PHY in this patch series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The TI DP83826 PHY can operate between two RMII modes:
	- master mode (PHY operates from a 25MHz clock reference)
        - slave mode (PHY operates from a 50MHz clock reference)

By default, the operation mode is configured by hardware straps.

Add support to configure the operation mode from within the driver.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The TI DP83826 PHY can operate in either MII mode or RMII mode.
By default, it is configured by straps.
It can also be configured by writing to the bit 5 of register 0x17 - RMII
and Status Register (RCSR).

When phydev->interface is rmii, rmii mode must be enabled, otherwise
mii mode must be set.
This prevents misconfiguration of hw straps.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add property ti,rmii-mode to support selecting the RMII operation mode
between:
	- master mode (PHY operates from a 25MHz clock reference)
	- slave mode (PHY operates from a 50MHz clock reference)

If not set, the operation mode is configured by hardware straps.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement bridge port isolation for KSZ switches. Enabling the isolation
of switch ports from each other while maintaining connectivity with the
CPU and other forwarding ports. For instance, to isolate swp1 and swp2
from each other, use the following commands:
- bridge link set dev swp1 isolated on
- bridge link set dev swp2 isolated on
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink and ethtool have a trailing _ in the header guard. I must have
copy/pasted it into new guards, assuming it's a headers_install artifact.

This fixes build if system headers are old.

Fixes: 8f109e91 ("tools: ynl: include dpll and mptcp_pm in C codegen")
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240222234831.179181-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Make the local variable in GENL_REQ_ATTR_CHECK() const.
genl_info_dump() returns a const pointer, so the macro
is currently hard to use in genl dumps.

Link: https://lore.kernel.org/r/20240222222819.156320-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jiri Pirko says:

====================
tools: ynl: couple of cmdline enhancements

This is part of the original "netlink: specs: devlink: add the rest of
missing attribute definitions" set which was rejected [1]. These three
patches enhances the cmdline user comfort, allowing to pass flag
attribute with bool values and enum names instead of scalars.

[1] https://lore.kernel.org/all/20240220181004.639af931@kernel.org/
====================

Link: https://lore.kernel.org/r/20240222134351.224704-1-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

During decoding of messages coming from kernel, attribute values are
converted to enum names in case the attribute type is enum of bitfield32.

However, when user constructs json message, he has to pass plain scalar
values. See "state" "selector" and "value" attributes in following
examples:

$ sudo ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml --do pin-set --json '{"id": 0, "parent-device": {"parent-id": 0, "state": 1}}'
$ sudo ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/devlink.yaml --do port-set --json '{"bus-name": "pci", "dev-name": "0000:08:00.1", "port-index": 98304, "port-function": {"caps": {"selector": 1, "value": 1 }}}'

Allow user to pass strings containing enum names, convert them to scalar
values to be encoded into Netlink message:

$ sudo ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml --do pin-set --json '{"id": 0, "parent-device": {"parent-id": 0, "state": "connected"}}'
$ sudo ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/devlink.yaml --do port-set --json '{"bus-name": "pci", "dev-name": "0000:08:00.1", "port-index": 98304, "port-function": {"caps": {"selector": ["roce-bit"], "value": ["roce-bit"] }}}'
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240222134351.224704-4-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

As a preparation to handle enums for scalar values, unify the processing
of all scalar types in a single elif statement.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240222134351.224704-3-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The flag attr presence in Netlink message indicates value "true",
if it is missing in the message it means "false".

Allow user to specify attrname with value "true"/"false"
in json for flag attrs, treat "false" value properly.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240222134351.224704-2-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

John Garry says:

====================
net: Don't bother filling in ethtool driver version

The drivers included in this series set the ethtool driver version to the
same as the default, UTS_RELEASE, so don't both doing this.

As noted by Masahiro in [0], with CONFIG_MODVERSIONS=y, some drivers could
be built as modules against a different kernel tree with differing
UTS_RELEASE. As such, these changes could lead to a change in behaviour.
However, defaulting to the core kernel UTS_RELEASE would be expected
behaviour.

[0] https://lore.kernel.org/all/CAK7LNASfTW+OMk1cJJWb4E6P+=k0FEsm_=6FDfDF_mTrxJCSMQ@mail.gmail.com/
====================

Link: https://lore.kernel.org/r/20240222090042.12609-1-john.g.garry@oracle.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The version is same as the default, so don't bother filling it in.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240222090042.12609-3-john.g.garry@oracle.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The version is same as the default, so don't bother filling it in.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240222090042.12609-2-john.g.garry@oracle.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

* Update the Kernel Doc for gelic_descr_set_tx_cmdstat()
  and gelic_net_setup_netdev() so that documented name
  and the actual name of the function match.

* Move define of GELIC_ALIGN() so that it is no longer
  between gelic_alloc_card_net() and it's Kernel Doc.

* Document netdev parameter of gelic_alloc_card_net()
  in a way consistent to the documentation of other netdev parameters
  in this file.

Addresses the following warnings flagged by ./scripts/kernel-doc -none:

  .../ps3_gelic_net.c:711: warning: expecting prototype for gelic_net_set_txdescr_cmdstat(). Prototype was for gelic_descr_set_tx_cmdstat() instead
  .../ps3_gelic_net.c:1474: warning: expecting prototype for gelic_ether_setup_netdev(). Prototype was for gelic_net_setup_netdev() instead
  .../ps3_gelic_net.c:1528: warning: expecting prototype for gelic_alloc_card_net(). Prototype was for GELIC_ALIGN() instead
  .../ps3_gelic_net.c:1531: warning: Function parameter or struct member 'netdev' not described in 'gelic_alloc_card_net'
Signed-off-by: Simon Horman <horms@kernel.org>
Acked-by: Geoff Levand <geoff@infradead.org>
Link: https://lore.kernel.org/r/20240221-ps3-gelic-kdoc-v1-1-7629216d1340@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

mpls_gso_segment() assumes skb_inner_network_header() returns
a valid result:

  mpls_hlen = skb_inner_network_header(skb) - skb_network_header(skb);
  if (unlikely(!mpls_hlen || mpls_hlen % MPLS_HLEN))
        goto out;
  if (unlikely(!pskb_may_pull(skb, mpls_hlen)))

With syzbot reproducer, skb_inner_network_header() yields 0,
skb_network_header() returns 108, so this will
"pskb_may_pull(skb, -108)))" which triggers a newly added
DEBUG_NET_WARN_ON_ONCE() check:

------------[ cut here ]------------
WARNING: CPU: 0 PID: 5068 at include/linux/skbuff.h:2723 pskb_may_pull_reason include/linux/skbuff.h:2723 [inline]
WARNING: CPU: 0 PID: 5068 at include/linux/skbuff.h:2723 pskb_may_pull include/linux/skbuff.h:2739 [inline]
WARNING: CPU: 0 PID: 5068 at include/linux/skbuff.h:2723 mpls_gso_segment+0x773/0xaa0 net/mpls/mpls_gso.c:34
[..]
 skb_mac_gso_segment+0x383/0x740 net/core/gso.c:53
 nsh_gso_segment+0x40a/0xad0 net/nsh/nsh.c:108
 skb_mac_gso_segment+0x383/0x740 net/core/gso.c:53
 __skb_gso_segment+0x324/0x4c0 net/core/gso.c:124
 skb_gso_segment include/net/gso.h:83 [inline]
 [..]
 sch_direct_xmit+0x11a/0x5f0 net/sched/sch_generic.c:327
 [..]
 packet_sendmsg+0x46a9/0x6130 net/packet/af_packet.c:3113
 [..]

First iteration of this patch made mpls_hlen signed and changed
test to error out to "mpls_hlen <= 0 || ..".

Eric Dumazet said:
 > I was thinking about adding a debug check in skb_inner_network_header()
 > if inner_network_header is zero (that would mean it is not 'set' yet),
 > but this would trigger even after your patch.

So add new skb_inner_network_header_was_set() helper and use that.

The syzbot reproducer injects data via packet socket. The skb that gets
allocated and passed down the stack has ->protocol set to NSH (0x894f)
and gso_type set to SKB_GSO_UDP | SKB_GSO_DODGY.

This gets passed to skb_mac_gso_segment(), which sees NSH as ptype to
find a callback for.  nsh_gso_segment() retrieves next type:

        proto = tun_p_to_eth_p(nsh_hdr(skb)->np);

... which is MPLS (TUN_P_MPLS_UC). It updates skb->protocol and then
calls mpls_gso_segment().  Inner offsets are all 0, so mpls_gso_segment()
ends up with a negative header size.

In case more callers rely on silent handling of such large may_pull values
we could also 'legalize' this behaviour, either replacing the debug check
with (len > INT_MAX) test or removing it and instead adding a comment
before existing

 if (unlikely(len > skb->len))
    return SKB_DROP_REASON_PKT_TOO_SMALL;

test in pskb_may_pull_reason(), saying that this check also implicitly
takes care of callers that miscompute header sizes.

Cc: Simon Horman <horms@kernel.org>
Fixes: 219eee9c ("net: skbuff: add overflow debug check to pull/push helpers")
Reported-by: syzbot+99d15fcdb0132a1e1a82@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/00000000000043b1310611e388aa@google.com/rawSigned-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240222140321.14080-1-fw@strlen.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, when you switch between branches or something like that and
rebuild, net/ethtool/ioctl.c has to be built again because it depends
on UTS_RELEASE.

By instead referencing a string variable stored in another object file,
this can be avoided.
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240220194244.2056384-1-jannh@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Serdes phy needs to operate at 2500 mode for 2.5G speed and 1000
mode for 1G/100M/10M speed.
Added changes to configure serdes phy and mac based on link speed.
Changing serdes phy speed involves multiple register writes for
serdes block. To avoid redundant write operations only update serdes
phy when new speed is different.
For 2500 speed MAC PCS autoneg needs to disabled. Added changes to
disable MAC PCS autoneg if ANE parameter is not set.
Signed-off-by: Sneh Shah <quic_snehshah@quicinc.com>
Tested-by: Abhishek Chauhan <quic_abchauha@quicinc.com> # sa8775p-ride
Reviewed-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Through the routine bond_mii_monitor(), bonding driver inspects and commits
the slave state changes. During the times when slave state change and
failure in aqcuiring rtnl lock happen at the same time, the routine
bond_mii_monitor() reschedules itself to come around after 1 msec to commit
the new state.

During this, it executes the routine bond_miimon_inspect() to re-inspect
the state chane and prints the corresponding slave state on to the console.
Hence we do see a message at every 1 msec till the rtnl lock is acquired
and state chage is committed.

This patch doesn't change how bond functions. It only simply limits this
kind of log flood.
Signed-off-by: Praveen Kumar Kannoju <praveen.kannoju@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20240221082752.4660-1-praveen.kannoju@oracle.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>