nf_flow_table_block_setup and the driver TC_SETUP_FT call can modify the flow
block cb list while they are being traversed elsewhere, causing a crash.
Add a write lock around the calls to protect readers

Fixes: c29f74e0 ("netfilter: nf_flow_table: hardware offload support")
Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The commit 510841da ("netfilter: ipset: enforce documented limit to
prevent allocating huge memory") was too strict and prevented to add up to
64 clashing elements to a hash:net,iface type of set. This patch fixes the
issue and now the type behaves as documented.

Fixes: 510841da ("netfilter: ipset: enforce documented limit to prevent allocating huge memory")
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This patch introduced a regression: commit 48596a8d ("netfilter:
ipset: Fix adding an IPv4 range containing more than 2^31 addresses")

The variable e.ip is passed to adtfn() function which finally adds the
ip address to the set. The patch above refactored the for loop and moved
e.ip = htonl(ip) to the end of the for loop.

What this means is that if the value of "ip" changes between the first
assignement of e.ip and the forloop, then e.ip is pointing to a
different ip address than "ip".

Test case:
$ ipset create jdtest_tmp hash:ip family inet hashsize 2048 maxelem 100000
$ ipset add jdtest_tmp 10.0.1.1/31
ipset v6.21.1: Element cannot be added to the set: it's already added

The value of ip gets updated inside the  "else if (tb[IPSET_ATTR_CIDR])"
block but e.ip is still pointing to the old value.

Fixes: 48596a8d ("netfilter: ipset: Fix adding an IPv4 range containing more than 2^31 addresses")
Reviewed-by: Joshua Hunt <johunt@akamai.com>
Signed-off-by: Vishwanath Pai <vpai@akamai.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This code accidentally uses the RX macro twice instead of the RX and TX.

Fixes: 6c635f78 ("octeontx2-af: cn10k: mcs: Handle MCS block interrupts")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Zero-length arrays are deprecated[1] and are being replaced with
flexible array members in support of the ongoing efforts to tighten the
FORTIFY_SOURCE routines on memcpy(), correctly instrument array indexing
with UBSAN_BOUNDS, and to globally enable -fstrict-flex-arrays=3.

Replace zero-length array with flexible-array member in struct key_vector.

This results in no differences in binary output.

[1] https://github.com/KSPP/linux/issues/78

Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Ahern <dsahern@kernel.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The `nettest` binary, built from `selftests/net/nettest.c`,
was expected to be found in the path during test execution of
`fcnal-test.sh` and `pmtu.sh`, leading to tests getting
skipped when the binary is not installed in the system, as can
be seen in these logs found in the wild [1]:

  # TEST: vti4: PMTU exceptions                                         [SKIP]
  [  350.600250] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
  [  350.607421] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
  # 'nettest' command not found; skipping tests
  #   xfrm6udp not supported
  # TEST: vti6: PMTU exceptions (ESP-in-UDP)                            [SKIP]
  [  351.605102] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
  [  351.612243] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
  # 'nettest' command not found; skipping tests
  #   xfrm4udp not supported

The `unicast_extensions.sh` tests also rely on `nettest`, but
it runs fine there because it looks for the binary in the
current working directory [2]:

The same mechanism that works for the Unicast extensions tests
is here copied over to the PMTU and functional tests.

[1] https://lkft.validation.linaro.org/scheduler/job/5839508#L6221
[2] https://lkft.validation.linaro.org/scheduler/job/5839508#L7958Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
The following patchset contains late Netfilter fixes for net:

1) Use READ_ONCE()/WRITE_ONCE() to update ct->mark, from Daniel Xu.
   Not reported by syzbot, but I presume KASAN would trigger post
   a splat on this. This is a rather old issue, predating git history.

2) Do not set up extensions for set element with end interval flag
   set on. This leads to bogusly skipping this elements as expired
   when listing the set/map to userspace as well as increasing
   memory consumpton when stateful expressions are used. This issue
   has been present since 4.18, when timeout support for rbtree set
   was added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Function sparx5_tc_setup_qdisc_ets() always returns negative value
because it return -EOPNOTSUPP in the end. This patch returns the
rersult of sparx5_tc_ets_add() and sparx5_tc_ets_del() directly.

Fixes: 21122542 ("net: microchip: sparx5: add support for offloading ets qdisc")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shang XiaoJing says:

====================
nfc: Fix potential memory leak of skb

There are still somewhere maybe leak the skb, fix the memleaks by adding
fail path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

s3fwrn5_nci_send() won't free the skb when it failed for the check
before s3fwrn5_write(). As the result, the skb will memleak. Free the
skb when the check failed.

Fixes: c04c674f ("nfc: s3fwrn5: Add driver for Samsung S3FWRN5 NFC Chip")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

nxp_nci_send() won't free the skb when it failed for the check before
write(). As the result, the skb will memleak. Free the skb when the
check failed.

Fixes: dece4585 ("NFC: nxp-nci: Add support for NXP NCI chips")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfcmrvl_i2c_nci_send() will be called by nfcmrvl_nci_send(), and skb
should be freed in nfcmrvl_i2c_nci_send(). However, nfcmrvl_nci_send()
won't free the skb when it failed for the test_bit(). Free the skb when
test_bit() failed.

Fixes: b5b3e23e ("NFC: nfcmrvl: add i2c driver")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

'ret' is defined twice in macsec_changelink(), when it is set in macsec_is_offloaded
case, it will be invalid before return.

Fixes: 3cf3227a ("net: macsec: hardware offloading infrastructure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20221118011249.48112-1-yuehaibing@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, we get icmp6hdr via function icmp6_hdr(), which needs the skb
transport header to be set first. But there is no rule to ask driver set
transport header before netif_receive_skb() and bond_handle_frame(). So
we will not able to get correct icmp6hdr on some drivers.

Fix this by using skb_header_pointer to get the IPv6 and ICMPV6 headers.
Reported-by: Liang Li <liali@redhat.com>
Fixes: 4e24be01 ("bonding: add new parameter ns_targets")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20221118034353.1736727-1-liuhangbin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Simon Horman says:

====================
nfp: fixes for v6.1

 - Ensure that information displayed by "devlink port show"
           reflects the number of lanes available to be split.
 - Avoid NULL dereference in ethtool test code.
====================

Link: https://lore.kernel.org/r/20221117153744.688595-1-simon.horman@corigine.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Setting of the port flag `NFP_PORT_CHANGED`, introduced
to ensure the correct reading of EEPROM data, causes a
fatal kernel NULL pointer dereference in cases where
the target netdev type cannot be determined.

Add validation of port struct pointer before attempting
to set the `NFP_PORT_CHANGED` flag. Return that operation
is not supported if the netdev type cannot be determined.

Fixes: 4ae97cae ("nfp: ethtool: fix the display error of `ethtool -m DEVNAME`")
Signed-off-by: Jaco Coetzee <jaco.coetzee@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The error is reflected in that it shows wrong splittable status of
port when executing "devlink port show".
The reason which leads the error is that the assigned operation of
splittable is just a simple negation operation of split and it does
not consider port lanes quantity. A splittable port should have
several lanes that can be split(lanes quantity > 1).
If without the judgement, it will show wrong message for some
firmware, such as 2x25G, 2x10G.

Fixes: a0f49b54 ("devlink: Add a new devlink port split ability attribute and pass to netlink")
Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().

In pch_gbe_probe(), pci_get_domain_bus_and_slot() is called,
so in error path in probe() and remove() function, pci_dev_put()
should be called to avoid refcount leak. Compile tested only.

Fixes: 1a0bdadb ("net/pch_gbe: supports eg20t ptp clock")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221117135148.301014-1-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().

So before returning from rvu_dbg_rvu_pf_cgx_map_display() or
cgx_print_dmac_flt(), pci_dev_put() is called to avoid refcount
leak.

Fixes: dbc52deb ("octeontx2-af: Debugfs support for DMAC filters")
Fixes: e2fb3730 ("octeontx2-af: Display CGX, NIX and PF map in debugfs.")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221117124658.162409-1-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The ql3xxx_send() returns NETDEV_TX_OK without freeing skb in error
handling case, add dev_kfree_skb_any() to fix it.

Fixes: bd36b0ac ("qla3xxx: Add support for Qlogic 4032 chip.")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1668675039-21138-1-git-send-email-zhangchangzhong@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

It will cause invalid pointer dereference to priv->cm3_base behind,
if PTR_ERR(priv->cm3_base) in mvpp2_get_sram().

Fixes: e54ad1e0 ("net: mvpp2: add CM3 SRAM memory map")
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Link: https://lore.kernel.org/r/20221117084032.101144-1-tanghui20@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If mlx4_bitmap_init fails, mlx4_bitmap_alloc_range will dereference
the NULL pointer (bitmap->table).

Make sure, that mlx4_bitmap_alloc_range called in no error case.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: d57febe1 ("net/mlx4: Add A0 hybrid steering")
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Peter Kosyh <pkosyh@yandex.ru>
Link: https://lore.kernel.org/r/20221117152806.278072-1-pkosyh@yandex.ruSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If mtk_start_dma() fails, invoke phylink_disconnect_phy() to perform
cleanup. phylink_disconnect_phy() contains the put_device action. If
phylink_disconnect_phy is not performed, the Kref of netdev will leak.

Fixes: b8fc9f30 ("net: ethernet: mediatek: Add basic PHYLINK support")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221117111356.161547-1-liujian56@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Elements with an end interval flag set on do not store extensions. The
global set definition is currently setting on the timeout and stateful
expression for end interval elements.

This leads to skipping end interval elements from the set->ops->walk()
path as the expired check bogusly reports true.

Moreover, do not set up stateful expressions for elements with end
interval flag set on since this is never used.

Fixes: 65038428 ("netfilter: nf_tables: allow to specify stateful expression in set definition")
Fixes: 8d8540c4 ("netfilter: nft_set_rbtree: add timeout support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

nf_conn:mark can be read from and written to in parallel. Use
READ_ONCE()/WRITE_ONCE() for reads and writes to prevent unwanted
compiler optimizations.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Daniel Xu <dxu@dxuuu.xyz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

In pch_gbe_xmit_frame(), NETDEV_TX_OK will be returned whether
pch_gbe_tx_queue() sends data successfully or not, so pch_gbe_tx_queue()
needs to free skb before returning. But pch_gbe_tx_queue() returns without
freeing skb in case of dma_map_single() fails. Add dev_kfree_skb_any()
to fix it.

Fixes: 77555ee7 ("net: Add Gigabit Ethernet driver of Topcliff PCH")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously we leverage NCI_UNREG and the lock inside nci_close_device to
prevent the race condition between opening a device and closing a
device. However, it still has problem because a failed opening command
will erase the NCI_UNREG flag and allow another opening command to
bypass the status checking.

This fix corrects that by making sure the NCI_UNREG is held.

Reported-by: syzbot+43475bf3cfbd6e41f5b7@syzkaller.appspotmail.com
Fixes: 48b71a9e ("NFC: add NCI_UNREG flag to eliminate the race")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

You'd think people know that the internal 100BASE-TX PHY on the SJA1110
responds only to clause 22 MDIO transactions, but they don't :)

When a clause 45 transaction is attempted, sja1105_base_tx_mdio_read()
and sja1105_base_tx_mdio_write() don't expect "reg" to contain bit 30
set (MII_ADDR_C45) and pack this value into the SPI transaction buffer.

But the field in the SPI buffer has a width smaller than 30 bits, so we
see this confusing message from the packing() API rather than a proper
rejection of C45 transactions:

Call trace:
 dump_stack+0x1c/0x38
 sja1105_pack+0xbc/0xc0 [sja1105]
 sja1105_xfer+0x114/0x2b0 [sja1105]
 sja1105_xfer_u32+0x44/0xf4 [sja1105]
 sja1105_base_tx_mdio_read+0x44/0x7c [sja1105]
 mdiobus_read+0x44/0x80
 get_phy_c45_ids+0x70/0x234
 get_phy_device+0x68/0x15c
 fwnode_mdiobus_register_phy+0x74/0x240
 of_mdiobus_register+0x13c/0x380
 sja1105_mdiobus_register+0x368/0x490 [sja1105]
 sja1105_setup+0x94/0x119c [sja1105]
Cannot store 401d2405 inside bits 24-4 (would truncate)

Fixes: 5a8f0974 ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

After rxrpc_unbundle_conn() has removed a connection from a bundle, it
checks to see if there are any conns with available channels and, if not,
removes and attempts to destroy the bundle.

Whilst it does check after grabbing client_bundles_lock that there are no
connections attached, this races with rxrpc_look_up_bundle() retrieving the
bundle, but not attaching a connection for the connection to be attached
later.

There is therefore a window in which the bundle can get destroyed before we
manage to attach a new connection to it.

Fix this by adding an "active" counter to struct rxrpc_bundle:

 (1) rxrpc_connect_call() obtains an active count by prepping/looking up a
     bundle and ditches it before returning.

 (2) If, during rxrpc_connect_call(), a connection is added to the bundle,
     this obtains an active count, which is held until the connection is
     discarded.

 (3) rxrpc_deactivate_bundle() is created to drop an active count on a
     bundle and destroy it when the active count reaches 0.  The active
     count is checked inside client_bundles_lock() to prevent a race with
     rxrpc_look_up_bundle().

 (4) rxrpc_unbundle_conn() then calls rxrpc_deactivate_bundle().

Fixes: 245500d8 ("rxrpc: Rewrite the client connection manager")
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-15975
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: zdi-disclosures@trendmicro.com
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit afef88e6 ("selftests/bpf: Store BPF object files with
.bpf.o extension"), we should use xdp_dummy.bpf.o instade of xdp_dummy.o.

In addition, use the BPF_FILE variable to save the BPF object file name,
which can be better identified and modified.

Fixes: afef88e6 ("selftests/bpf: Store BPF object files with .bpf.o extension")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Cc: Daniel Müller <deso@posteo.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recently syzkaller discovered the issue of disappearing lower
device (NETDEV_UNREGISTER) while the virtual device (like
macvlan) is still having it as a lower device. So it's just
a matter of time similar discovery will be made for IPvlan
device setup. So fixing it preemptively. Also while at it,
add a refcount tracker.

Fixes: 2ad7bf36 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0ff4eb3d ("neighbour: make proxy_queue.qlen limit
per-device") introduced the length counter qlen in struct neigh_parms.
There are separate neigh_parms instances for IPv4/ARP and IPv6/ND, and
while the family specific qlen is incremented in pneigh_enqueue(), the
mentioned commit decrements always the IPv4/ARP specific qlen,
regardless of the currently processed family, in pneigh_queue_purge()
and neigh_proxy_process().

As a result, with IPv6/ND, the family specific qlen is only incremented
(and never decremented) until it exceeds PROXY_QLEN, and then, according
to the check in pneigh_enqueue(), neighbor solicitations are not
answered anymore. As an example, this is noted when using the
subnet-router anycast address to access a Linux router. After a certain
amount of time (in the observed case, qlen exceeded PROXY_QLEN after two
days), the Linux router stops answering neighbor solicitations for its
subnet-router anycast address and effectively becomes unreachable.

Another result with IPv6/ND is that the IPv4/ARP specific qlen is
decremented more often than incremented. This leads to negative qlen
values, as a signed integer has been used for the length counter qlen,
and potentially to an integer overflow.

Fix this by introducing the helper function neigh_parms_qlen_dec(),
which decrements the family specific qlen. Thereby, make use of the
existing helper function neigh_get_dev_parms_rcu(), whose definition
therefore needs to be placed earlier in neighbour.c. Take the family
member from struct neigh_table to determine the currently processed
family and appropriately call neigh_parms_qlen_dec() from
pneigh_queue_purge() and neigh_proxy_process().

Additionally, use an unsigned integer for the length counter qlen.

Fixes: 0ff4eb3d ("neighbour: make proxy_queue.qlen limit per-device")
Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the warning reported by kbuild:

cocci warnings: (new ones prefixed by >>)
>> drivers/net/ethernet/cavium/liquidio/lio_main.c:1797:54-56: WARNING !A || A && B is equivalent to !A || B
   drivers/net/ethernet/cavium/liquidio/lio_main.c:1827:54-56: WARNING !A || A && B is equivalent to !A || B

Fixes: 8979f428 ("net: liquidio: release resources when liquidio driver open failed")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
mptcp: selftests: Fix timeouts and test isolation

Patches 1 and 3 adjust test timeouts to reduce false negatives on slow
machines.

Patch 2 improves test isolation by running the mptcp_sockopt test in its
own net namespace.
====================

Link: https://lore.kernel.org/r/20221115221046.20370-1-mathew.j.martineau@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The estimated time was supposing the rate was expressed in mibit
(bit * 1024^2) but it is in mbit (bit * 1000^2).

This makes the threshold higher but in a more realistic way to avoid
false positives reported by CI instances.

Before this patch, the thresholds were at 7561/4005ms and now they are
at 7906/4178ms.

While at it, also fix a typo in the linked comment, spotted by Mat.

Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/310
Fixes: 1a418cb8 ("mptcp: simult flow self-tests")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Not running it from a new netns causes issues if some MPTCP settings are
modified, e.g. if MPTCP is disabled from the sysctl knob, if multiple
addresses are available and added to the MPTCP path-manager, etc.

In these cases, the created connection will not behave as expected, e.g.
unable to create an MPTCP socket, more than one subflow is seen, etc.

A new "sandbox" net namespace is now created and used to run
mptcp_sockopt from this controlled environment.

Fixes: ce997912 ("selftests: mptcp: add mptcp getsockopt test cases")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On slow or busy VM, some test-cases still fail because the
data transfer completes before the endpoint manipulation
actually took effect.

Address the issue by artificially increasing the runtime for
the relevant test-cases.

Fixes: ef360019 ("selftests: mptcp: signal addresses testcases")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/309Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Paolo Abeni:
 "Including fixes from bpf.

  Current release - regressions:

   - tls: fix memory leak in tls_enc_skb() and tls_sw_fallback_init()

  Previous releases - regressions:

   - bridge: fix memory leaks when changing VLAN protocol

   - dsa: make dsa_master_ioctl() see through port_hwtstamp_get() shims

   - dsa: don't leak tagger-owned storage on switch driver unbind

   - eth: mlxsw: avoid warnings when not offloaded FDB entry with IPv6
     is removed

   - eth: stmmac: ensure tx function is not running in
     stmmac_xdp_release()

   - eth: hns3: fix return value check bug of rx copybreak

  Previous releases - always broken:

   - kcm: close race conditions on sk_receive_queue

   - bpf: fix alignment problem in bpf_prog_test_run_skb()

   - bpf: fix writing offset in case of fault in
     strncpy_from_kernel_nofault

   - eth: macvlan: use built-in RCU list checking

   - eth: marvell: add sleep time after enabling the loopback bit

   - eth: octeon_ep: fix potential memory leak in octep_device_setup()

  Misc:

   - tcp: configurable source port perturb table size

   - bpf: Convert BPF_DISPATCHER to use static_call() (not ftrace)"

* tag 'net-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (51 commits)
  net: use struct_group to copy ip/ipv6 header addresses
  net: usb: smsc95xx: fix external PHY reset
  net: usb: qmi_wwan: add Telit 0x103a composition
  netdevsim: Fix memory leak of nsim_dev->fa_cookie
  tcp: configurable source port perturb table size
  l2tp: Serialize access to sk_user_data with sk_callback_lock
  net: thunderbolt: Fix error handling in tbnet_init()
  net: microchip: sparx5: Fix potential null-ptr-deref in sparx_stats_init() and sparx5_start()
  net: lan966x: Fix potential null-ptr-deref in lan966x_stats_init()
  net: dsa: don't leak tagger-owned storage on switch driver unbind
  net/x25: Fix skb leak in x25_lapb_receive_frame()
  net: ag71xx: call phylink_disconnect_phy if ag71xx_hw_enable() fail in ag71xx_open()
  bridge: switchdev: Fix memory leaks when changing VLAN protocol
  net: hns3: fix setting incorrect phy link ksettings for firmware in resetting process
  net: hns3: fix return value check bug of rx copybreak
  net: hns3: fix incorrect hw rss hash type of rx packet
  net: phy: marvell: add sleep time after enabling the loopback bit
  net: ena: Fix error handling in ena_init()
  kcm: close race conditions on sk_receive_queue
  net: ionic: Fix error handling in ionic_init_module()
  ...

kernel test robot reported warnings when build bonding module with
make W=1 O=build_dir ARCH=x86_64 SHELL=/bin/bash drivers/net/bonding/:

                 from ../drivers/net/bonding/bond_main.c:35:
In function ‘fortify_memcpy_chk’,
    inlined from ‘iph_to_flow_copy_v4addrs’ at ../include/net/ip.h:566:2,
    inlined from ‘bond_flow_ip’ at ../drivers/net/bonding/bond_main.c:3984:3:
../include/linux/fortify-string.h:413:25: warning: call to ‘__read_overflow2_field’ declared with attribute warning: detected read beyond size of f
ield (2nd parameter); maybe use struct_group()? [-Wattribute-warning]
  413 |                         __read_overflow2_field(q_size_field, size);
      |                         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In function ‘fortify_memcpy_chk’,
    inlined from ‘iph_to_flow_copy_v6addrs’ at ../include/net/ipv6.h:900:2,
    inlined from ‘bond_flow_ip’ at ../drivers/net/bonding/bond_main.c:3994:3:
../include/linux/fortify-string.h:413:25: warning: call to ‘__read_overflow2_field’ declared with attribute warning: detected read beyond size of f
ield (2nd parameter); maybe use struct_group()? [-Wattribute-warning]
  413 |                         __read_overflow2_field(q_size_field, size);
      |                         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

This is because we try to copy the whole ip/ip6 address to the flow_key,
while we only point the to ip/ip6 saddr. Note that since these are UAPI
headers, __struct_group() is used to avoid the compiler warnings.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: c3f83241 ("net: Add full IPv6 addresses to flow_keys")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20221115142400.1204786-1-liuhangbin@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

An external PHY needs settling time after power up or reset.
In the bind() function an mdio bus is registered. If at this point
the external PHY is still initialising, no valid PHY ID will be
read and on phy_find_first() the bind() function will fail.

If an external PHY is present, wait the maximum time specified
in 802.3 45.2.7.1.1.

Fixes: 05b35e7e ("smsc95xx: add phylib support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221115114434.9991-2-alexandru.tachici@analog.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>