Clear ADDR64 dma bit in DMACFG register in case that HW_DMA_CAP_64B is
not detected on 64bit system.
The issue was observed when bootloader(u-boot) does not check macb
feature at DCFG6 register (DAW64_OFFSET) and enabling 64bit dma support
by default. Then macb driver is reading DMACFG register back and only
adding 64bit dma configuration but not cleaning it out.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: series with smaller improvements

This series includes smaller improvements, nothing exciting.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The check for pci_is_pcie() is redundant here because all
chip versions >=18 are PCIe only anyway. In addition use
dma_set_mask_and_coherent() instead of separate calls to
pci_set_dma_mask() and pci_set_consistent_dma_mask().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Code can be slightly simplified by acking even events we're not
interested in. In addition add a comment making clear that the
read has no functional purpose and is just a PCI commit.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The networking core has a default watchdog timeout of 5s. I see no
need to define an own timeout of 6s which is basically the same.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Until now, the Rx flow hash key was a 5-tuple (IP src, IP dst,
IP nextproto, L4 src port, L4 dst port) fixed value that we
configured at probe.

Add support for configuring this hash key at runtime.
We support all standard header fields configurable through ethtool,
but cannot differentiate between flow types, so the same hash key
is applied regardless of protocol.

We also don't support the discard option.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SPI protocol for the QCA7000 doesn't have any fault detection.
In order to increase the drivers reliability in noisy environments,
we could implement a write verification inspired by the enc28j60.
This should avoid situations were the driver wrongly assumes the
receive interrupt is enabled and miss all incoming packets.

This function is disabled per default and can be controlled via module
parameter wr_verify.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In tls_sw_sendmsg() and tls_sw_sendpage(), it is possible that the
uninitialised variable 'ret' gets passed to sk_stream_error(). So
initialise local variable 'ret' to '0. The warnings were detected by
'smatch' tool.

Fixes: a42055e8 ("net/tls: Add support for async encryption")
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On processors with multi-engine crypto accelerators, it is possible that
multiple records get encrypted in parallel and their encryption
completion is notified to different cpus in multicore processor. This
leads to the situation where tls_encrypt_done() starts executing in
parallel on different cores. In current implementation, encrypted
records are queued to tx_ready_list in tls_encrypt_done(). This requires
addition to linked list 'tx_ready_list' to be protected. As
tls_decrypt_done() could be executing in irq content, it is not possible
to protect linked list addition operation using a lock.

To fix the problem, we remove linked list addition operation from the
irq context. We do tx_ready_list addition/removal operation from
application context only and get rid of possible multiple access to
the linked list. Before starting encryption on the record, we add it to
the tail of tx_ready_list. To prevent tls_tx_records() from transmitting
it, we mark the record with a new flag 'tx_ready' in 'struct tls_rec'.
When record encryption gets completed, tls_encrypt_done() has to only
update the 'tx_ready' flag to true & linked list add operation is not
required.

The changed logic brings some other side benefits. Since the records
are always submitted in tls sequence number order for encryption, the
tx_ready_list always remains sorted and addition of new records to it
does not have to traverse the linked list.

Lastly, we renamed tx_ready_list in 'struct tls_sw_context_tx' to
'tx_list'. This is because now, the some of the records at the tail are
not ready to transmit.

Fixes: a42055e8 ("net/tls: Add support for async encryption")
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Roopa Prabhu says:

====================
few NTF_ROUTER related updates

This series allows setting of NTF_ROUTER by an external
entity (eg BGP E-VPN control plane). Also fixes missing
netlink notification on neigh NTF_ROUTER flag changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

send netlink notification if neigh_update results in NTF_ROUTER
change and if NEIGH_UPDATE_F_ISROUTER is on. Also move the
NTF_ROUTER change function into a helper.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch allows admin setting of NTF_ROUTER flag
on a neighbour entry. This enables external control
plane (like bgp evpn) to manage neigh entries with
NTF_ROUTER flag.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eelco Chaudron says:

====================
net/sched: Add hardware specific counters to TC actions

Add hardware specific counters to TC actions which will be exported
through the netlink API. This makes troubleshooting TC flower offload
easier, as it possible to differentiate the packets being offloaded.

v2 - Rebased on latest net-next
====================
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add additional counters that will store the bytes/packets processed by
hardware. These will be exported through the netlink interface for
displaying by the iproute2 tc tool
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new hardware specific basic counter, TCA_STATS_BASIC_HW. This can
be used to count packets/bytes processed by hardware offload.
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Maxime Chevallier says:

====================
net: mvpp2: Add txq to CPU mapping

This short series adds XPS support to the mvpp2 driver, by mapping
txqs and CPUs. This comes with a patch using round-robin scheduling
for the HW to pick the next txq to transmit from, instead of the default
fixed-priority scheduling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit allows each TXQ to be picked in a round-robin fashion by
the PPv2 transmit scheduling mechanism. This is opposed to the default
behaviour that prioritizes the highest numbered queues.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the PPv2 controller has multiple TX queues, we can spread traffic
by assining TX queues to CPUs, allowing to use XPS to balance egress
traffic between CPUs.

Suggested-by : Yan Markman <ymarkman@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Up until now, mlxsw tolerated firmware versions that weren't exactly
matching the required version, if the branch number matched. That
allowed the users to test various firmware versions as long as they were
on the right branch.

On the other hand, it made it impossible for mlxsw to put a hard lower
bound on a version that fixes all problems known to date. If a user had
a somewhat older FW version installed, mlxsw would start up just fine,
possibly performing non-optimally as it would use features that trigger
problematic behavior.

Therefore tweak the check to accept any FW version that is:

- on the same branch as the preferred version, and
- the same as or newer than the preferred version.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Haiyang Zhang says:

====================
hv_netvsc: Support LRO/RSC in the vSwitch

The patch adds support for LRO/RSC in the vSwitch feature. It reduces
the per packet processing overhead by coalescing multiple TCP segments
when possible. The feature is enabled by default on VMs running on
Windows Server 2019 and later.

The patch set also adds ethtool command handler and documents.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update document for LRO/RSC support, and the command line info to
change the setting.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the handler for LRO setting change, so that a user
can use ethtool command to enable / disable LRO feature.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

LRO/RSC in the vSwitch is a feature available in Windows Server 2019
hosts and later. It reduces the per packet processing overhead by
coalescing multiple TCP segments when possible. This patch adds netvsc
driver support for this feature.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: b53: SGMII modes fixes

Here are two additional fixes that are required in order for SGMII to
work correctly. This was discovered with using a copper SFP which would
make us use SGMII mode, we would actually leave the HW configured in its
default mode: Fiber.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In both 802.3z and SGMII modes we need to configure the MAC accordingly
to flip between Fiber and SGMII modes, and we need to read the MAC
status from the SGMII in-band control word.

Fixes: 0e01491d ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Maths went wrong, to get 0x20, we need to do 0x1e + (x) * 2, not 0x18,
fix that offset so we access the correct registers. This would make us
not access the correct SerDes Digital control words, status would be
fine and so we would not be correctly flipping between Fiber and SGMII
modes resulting in incorrect status words being pulled into the SerDes
digital status register.

Fixes: 0e01491d ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PHYLINK takes care of filing the right information into
state->an_enabled, get rid of the read from the SerDes's BMCR register.

Fixes: 0e01491d ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clang warns that the address of a pointer will always evaluated as true
in a boolean context.

net/decnet/dn_dev.c:1366:10: warning: address of array 'dev->name' will
always evaluate to 'true' [-Wpointer-bool-conversion]
                                dev->name ? dev->name : "???",
                                ~~~~~^~~~ ~
1 warning generated.

Link: https://github.com/ClangBuiltLinux/linux/issues/116Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds ipv6 defragmentation tests to ip_defrag selftest,
to complement existing ipv4 tests.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, ip[6]frag_high_thresh sysctl values in new namespaces are
hard-limited to those of the root/init ns.

There are at least two use cases when it would be desirable to
set the high_thresh values higher in a child namespace vs the global hard
limit:

- a security/ddos protection policy may lower the thresholds in the
  root/init ns but allow for a special exception in a child namespace
- testing: a test running in a namespace may want to set these
  thresholds higher in its namespace than what is in the root/init ns

The new behavior:

 # ip netns add testns
 # ip netns exec testns bash

 # sysctl -w net.ipv4.ipfrag_high_thresh=9000000
 net.ipv4.ipfrag_high_thresh = 9000000

 # sysctl net.ipv4.ipfrag_high_thresh
 net.ipv4.ipfrag_high_thresh = 9000000

 # sysctl -w net.ipv6.ip6frag_high_thresh=9000000
 net.ipv6.ip6frag_high_thresh = 9000000

 # sysctl net.ipv6.ip6frag_high_thresh
 net.ipv6.ip6frag_high_thresh = 9000000

The old behavior:

 # ip netns add testns
 # ip netns exec testns bash

 # sysctl -w net.ipv4.ipfrag_high_thresh=9000000
 net.ipv4.ipfrag_high_thresh = 9000000

 # sysctl net.ipv4.ipfrag_high_thresh
 net.ipv4.ipfrag_high_thresh = 4194304

 # sysctl -w net.ipv6.ip6frag_high_thresh=9000000
 net.ipv6.ip6frag_high_thresh = 9000000

 # sysctl net.ipv6.ip6frag_high_thresh
 net.ipv6.ip6frag_high_thresh = 4194304
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is similar to how ipv4 now behaves:
commit 0ff89efb ("ip: fail fast on IP defrag errors").
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/ipv4/fib_frontend.c: In function 'fib_info_nh_uses_dev':
net/ipv4/fib_frontend.c:322:6: error: unused variable 'ret' [-Werror=unused-variable]
cc1: all warnings being treated as errors

Fixes: 78f2756c ("net/ipv4: Move device validation to helper")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
tcp: switch to Early Departure Time model

In the early days, pacing has been implemented in sch_fq (FQ)
in a generic way :

- SO_MAX_PACING_RATE could be used by any sockets.

- TCP would vary effective pacing rate based on CWND*MSS/SRTT

- FQ would ensure delays between packets based on current
  sk->sk_pacing_rate, but with some quantum based artifacts.
  (inflating RPC tail latencies)

- BBR then tweaked the pacing rate in its various phases
  (PROBE, DRAIN, ...)

This worked reasonably well, but had the side effect that TCP RTT
samples would be inflated by the sojourn time of the packets in FQ.

Also note that when FQ is not used and TCP wants pacing, the
internal pacing fallback has very different behavior, since TCP
emits packets at the time they should be sent (with unreasonable
assumptions about scheduling costs)

Van Jacobson gave a talk at Netdev 0x12 in Montreal, about letting
TCP (or applications for UDP messages) decide of the Earliest
Departure Time, instead of letting packet schedulers derive it
from pacing rate.

https://www.netdevconf.org/0x12/session.html?evolving-from-afap-teaching-nics-about-time
https://www.files.netdevconf.org/d/46def75c2ef345809bbe/files/?p=/Evolving%20from%20AFAP%20%E2%80%93%20Teaching%20NICs%20about%20time.pdf

Recent additions in linux provided SO_TXTIME and a new ETF qdisc
supporting the new skb->tstamp role

This patch series converts TCP and FQ to the same model.

This might in the future allow us to relax tight TSQ limits
(if FQ is present in the output path), and thus lower
number of callbacks to tcp_write_xmit(), thanks to batching.

This will be followed by FQ change allowing SO_TXTIME support
so that QUIC servers can let the pacing being done in FQ (or
offloaded if network device permits)

For example, a TCP flow rated at 24Mbps now shows a more meaningful RTT

Before :

ESTAB  0  211408 10.246.7.151:41558   10.246.7.152:33723
	 cubic wscale:8,8 rto:203 rtt:2.195/0.084 mss:1448 rcvmss:536
  advmss:1448 cwnd:20 ssthresh:20 bytes_acked:36897937
  segs_out:25488 segs_in:12454 data_segs_out:25486
  send 105.5Mbps lastsnd:1 lastrcv:12851 lastack:1
  pacing_rate 24.0Mbps/24.0Mbps delivery_rate 22.9Mbps
  busy:12851ms unacked:4 rcv_space:29200 notsent:205616 minrtt:0.026

After :

ESTAB  0  192584 10.246.7.151:61612   10.246.7.152:34375
	 cubic wscale:8,8 rto:201 rtt:0.165/0.129 mss:1448 rcvmss:536
  advmss:1448 cwnd:20 ssthresh:20 bytes_acked:170755401
  segs_out:117931 segs_in:57651 data_segs_out:117929
  send 1404.1Mbps lastsnd:1 lastrcv:56915 lastack:1
  pacing_rate 24.0Mbps/24.0Mbps delivery_rate 24.2Mbps
  busy:56915ms unacked:4 rcv_space:29200 notsent:186792 minrtt:0.054

A nice side effect of this patch series is a reduction of max/p99
latencies of RPC workloads, since the FQ quantum no longer adds
artifact.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With the earliest departure time model, we no longer plan
special casing TCP retransmits. We therefore remove dead
code (since most compilers understood skb_is_retransmit()
was false)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now TCP keeps track of tcp_wstamp_ns, recording the earliest
departure time of next packet, we can remove duplicate code
from tcp_internal_pacing()

This removes one ktime_get_tai_ns() call, and a divide.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP keeps track of tcp_wstamp_ns by itself, meaning sch_fq
no longer has to do it.

Thanks to this model, TCP can get more accurate RTT samples,
since pacing no longer inflates them.

This has the nice effect of removing some delays caused by FQ
quantum mechanism, causing inflated max/P99 latencies.

Also we might relax TCP Small Queue tight limits in the future,
since this new model allow TCP to build bigger batches, since
sch_fq (or a device with earliest departure time offload) ensure
these packets will be delivered on time.

Note that other protocols are not converted (they will probably
never be) so sch_fq has still support for SO_MAX_PACING_RATE

Tested:

Test showing FQ pacing quantum artifact for low-rate flows,
adding unexpected throttles for RPC flows, inflating max and P99 latencies.

The parameters chosen here are to show what happens typically when
a TCP flow has a reduced pacing rate (this can be caused by a reduced
cwin after few losses, or/and rtt above few ms)

MIBS="MIN_LATENCY,MEAN_LATENCY,MAX_LATENCY,P99_LATENCY,STDDEV_LATENCY"
Before :
$ netperf -H 10.246.7.133 -t TCP_RR -Cc -T6,6 -- -q 2000000 -r 100,100 -o $MIBS
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.246.7.133 () port 0 AF_INET : first burst 0 : cpu bind
 Minimum Latency Microseconds,Mean Latency Microseconds,Maximum Latency Microseconds,99th Percentile Latency Microseconds,Stddev Latency Microseconds
19,82.78,5279,3825,482.02

After :
$ netperf -H 10.246.7.133 -t TCP_RR -Cc -T6,6 -- -q 2000000 -r 100,100 -o $MIBS
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.246.7.133 () port 0 AF_INET : first burst 0 : cpu bind
Minimum Latency Microseconds,Mean Latency Microseconds,Maximum Latency Microseconds,99th Percentile Latency Microseconds,Stddev Latency Microseconds
20,49.94,128,63,3.18
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Next patch will use tcp_wstamp_ns to feed internal
TCP pacing timer, so switch to CLOCK_TAI to share same base.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Switch internal TCP skb->skb_mstamp to skb->skb_mstamp_ns,
from usec units to nsec units.

Do not clear skb->tstamp before entering IP stacks in TX,
so that qdisc or devices can implement pacing based on the
earliest departure time instead of socket sk->sk_pacing_rate

Packets are fed with tcp_wstamp_ns, and following patch
will update tcp_wstamp_ns when both TCP and sch_fq switch to
the earliest departure time mechanism.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP will soon provide earliest departure time on TX skbs.
It needs to track this in a new variable.

tcp_mstamp_refresh() needs to update this variable, and
became too big to stay an inline.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP will soon provide per skb->tstamp with earliest departure time,
so that sch_fq does not have to determine departure time by looking
at socket sk_pacing_rate.

We chose in linux-4.19 CLOCK_TAI as the clock base for transports,
qdiscs, and NIC offloads.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>