- 13 Nov, 2019 18 commits
-
-
Ramuthevar Vadivel Murugan authored
Add a new compatible to use the sdhc-arasan host controller driver with the SDXC PHY to support on Intel's Lightning Mountain(LGM) SoC. Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Ludovic Barre authored
This patch adds a specific busy_complete callback for sdmmc variant. sdmmc has 2 status flags: -busyd0: This is a hardware status flag (inverted value of d0 line). it does not generate an interrupt. -busyd0end: This indicates only end of busy following a CMD response. On busy to Not busy changes, an interrupt is generated (if unmask) and BUSYD0END status flag is set. Status flag is cleared by writing corresponding interrupt clear bit in MMCICLEAR. The legacy busy completion has no dedicated interrupt for the end of busy, so it's must monitor step by step the busy progression. On sdmmc variant, this procedure is not needed, it's just need to wait the busyd0end interrupt. Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Ludovic Barre authored
This patch adds busy_completion callback at mmci_host_ops to allow to define a specific busy completion by variant. The legacy code corresponding to busy completion used by ux500 variants is moved to ux500_busy_complete function. Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Ludovic Barre authored
In the stm32_sdmmc variant, the datatimer is active not only during data transfers with the DPSM, but also while waiting for the busyend IRQs from commands having the MMC_RSP_BUSY flag set. This leads to an incorrect IRQ being raised to signal MCI_DATATIMEOUT error, which simply breaks the behaviour. Address this by updating the datatimer value before sending a command having the MMC_RSP_BUSY flag set. To inform the mmc core about the maximum supported busy timeout, which also depends on the current clock rate, set ->max_busy_timeout (in ms). Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Ben Dooks authored
Fix the following sparse warnings by making any functions not used outsde the mmci.c driver static. drivers/mmc/host/mmci.c:422:6: warning: symbol 'mmci_dma_release' was not declared. Should it be static? drivers/mmc/host/mmci.c:430:6: warning: symbol 'mmci_dma_setup' was not declared. Should it be static? drivers/mmc/host/mmci.c:465:5: warning: symbol 'mmci_prep_data' was not declared. Should it be static? drivers/mmc/host/mmci.c:481:6: warning: symbol 'mmci_unprep_data' was not declared. Should it be static? drivers/mmc/host/mmci.c:490:6: warning: symbol 'mmci_get_next_data' was not declared. Should it be static? drivers/mmc/host/mmci.c:498:5: warning: symbol 'mmci_dma_start' was not declared. Should it be static? drivers/mmc/host/mmci.c:533:6: warning: symbol 'mmci_dma_finalize' was not declared. Should it be static? drivers/mmc/host/mmci.c:542:6: warning: symbol 'mmci_dma_error' was not declared. Should it be static? drivers/mmc/host/mmci.c:951:6: warning: symbol 'mmci_variant_init' was not declared. Should it be static? drivers/mmc/host/mmci.c:956:6: warning: symbol 'ux500v2_variant_init' was not declared. Should it be static? Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Colin Ian King authored
There are a couple of statements that are indented by an extra space, clean this up by remove the extraneous spaces. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Colin Ian King authored
There is a hunk of code that is indented one level too deep, fix this by removing the extraneous tabs. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Biju Das authored
Document RZ/G2N (R8A774B1) SoC bindings. Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Markus Elfring authored
Simplify this function implementation by using a known wrapper function. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Saiyam Doshi authored
Use devm_platform_ioremap_resource helper which wraps platform_get_resource() and devm_ioremap_resource() together. Generated by: scripts/coccinelle/api/devm_platform_ioremap_resource.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/Signed-off-by: Saiyam Doshi <saiyamdoshi.in@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Wolfram Sang authored
PM has been reworked, so eMMC gets now detected on R-Car H3 ES1.0 and 2.0 as well as M3-N without the workaround. Card detect and write protect also still work. Remove the workaround. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Manivannan Sadhasivam authored
Add MAINTAINERS entry for Actions Semi SD/MMC driver with its binding. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Manivannan Sadhasivam authored
Add SD/MMC driver for Actions Semi Owl SoCs. This driver currently supports standard, high speed, SDR12, SDR25 and SDR50. DDR50 mode is supported but it is untested. There is no SDIO support for now. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Manivannan Sadhasivam authored
Add devicetree YAML binding for Actions Semi Owl SoC's SD/MMC/SDIO controller. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Takao Orito authored
SD Host controller on Milbeaut consists of two controller parts. One is core controller F_SDH30, this is similar to sdhci-fujitsu controller. Another is bridge controller. This bridge controller is not compatible with sdhci-fujitsu controller. This is special for Milbeaut series. This has some functions. For example, reset control, clock enable/select for SDR50/25/12, set property of SD physical pins, retuning control, set capabilityies. This bridge controller requires special procedures at reset or clock enablement or change for further tuning of clock. Signed-off-by: Takao Orito <orito.takao@socionext.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Takao Orito authored
Add the device-tree binding documentation for Milbeaut SDHCI driver. Signed-off-by: Takao Orito <orito.takao@socionext.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Raul E Rangel authored
AMD SDHC 0x7906 requires a hard reset to clear all internal state. Otherwise it can get into a bad state where the DATA lines are always read as zeros. This change requires firmware that can transition the device into D3Cold for it to work correctly. If the firmware does not support transitioning to D3Cold then the power state transitions are a no-op. Signed-off-by: Raul E Rangel <rrangel@chromium.org> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Raul E Rangel authored
In sdhci_do_reset we call the reset callback which is typically sdhci_reset. sdhci_reset can wait for up to 100ms waiting for the controller to reset. If SDHCI_RESET_ALL was passed as the flag, the controller will clear the IRQ mask. If during that 100ms the card is removed there is no notification to the MMC system that the card was removed. So from the drivers point of view the card is always present. By making sdhci_reinit compare the present state it can schedule a rescan if the card was removed while a reset was in progress. Signed-off-by: Raul E Rangel <rrangel@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
- 11 Nov, 2019 1 commit
-
-
Linus Torvalds authored
-
- 10 Nov, 2019 13 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds authored
Pull ARM SoC fixes from Olof Johansson: "A set of fixes that have trickled in over the last couple of weeks: - MAINTAINER update for Cavium/Marvell ThunderX2 - stm32 tweaks to pinmux for Joystick/Camera, and RAM allocation for CAN interfaces - i.MX fixes for voltage regulator GPIO mappings, fixes voltage scaling issues - More i.MX fixes for various issues on i.MX eval boards: interrupt storm due to u-boot leaving pins in new states, fixing power button config, a couple of compatible-string corrections. - Powerdown and Suspend/Resume fixes for Allwinner A83-based tablets - A few documentation tweaks and a fix of a memory leak in the reset subsystem" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: MAINTAINERS: update Cavium ThunderX2 maintainers ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1 ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1 ARM: dts: stm32: Fix CAN RAM mapping on stm32mp157c ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157 arm64: dts: zii-ultra: fix ARM regulator GPIO handle ARM: sunxi: Fix CPU powerdown on A83T ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend arm64: dts: imx8mn: fix compatible string for sdma arm64: dts: imx8mm: fix compatible string for sdma reset: fix reset_control_ops kerneldoc comment ARM: dts: imx6-logicpd: Re-enable SNVS power key soc: imx: gpc: fix initialiser format ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts arm64: dts: ls1028a: fix a compatible issue reset: fix reset_control_get_exclusive kerneldoc comment reset: fix reset_control_lookup kerneldoc comment reset: fix of_reset_control_get_count kerneldoc comment reset: fix of_reset_simple_xlate kerneldoc comment reset: Fix memory leak in reset_control_array_put()
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/stagingLinus Torvalds authored
Pull IIO fixes and staging driver from Greg KH: "Here is a mix of a number of IIO driver fixes for 5.4-rc7, and a whole new staging driver. The IIO fixes resolve some reported issues, all are tiny. The staging driver addition is the vboxsf filesystem, which is the VirtualBox guest shared folder code. Hans has been trying to get filesystem reviewers to review the code for many months now, and Christoph finally said to just merge it in staging now as it is stand-alone and the filesystem people can review it easier over time that way. I know it's late for this big of an addition, but it is stand-alone. The code has been in linux-next for a while, long enough to pick up a few tiny fixes for it already so people are looking at it. All of these have been in linux-next with no reported issues" * tag 'staging-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging: Fix error return code in vboxsf_fill_super() staging: vboxsf: fix dereference of pointer dentry before it is null checked staging: vboxsf: Remove unused including <linux/version.h> staging: Add VirtualBox guest shared folder (vboxsf) support iio: adc: stm32-adc: fix stopping dma iio: imu: inv_mpu6050: fix no data on MPU6050 iio: srf04: fix wrong limitation in distance measuring iio: imu: adis16480: make sure provided frequency is positive
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-miscLinus Torvalds authored
Pull char/misc driver fixes from Greg KH: "Here are a number of late-arrival driver fixes for issues reported for some char/misc drivers for 5.4-rc7 These all come from the different subsystem/driver maintainers as things that they had reports for and wanted to see fixed. All of these have been in linux-next with no reported issues" * tag 'char-misc-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: intel_th: pci: Add Jasper Lake PCH support intel_th: pci: Add Comet Lake PCH support intel_th: msu: Fix possible memory leak in mode_store() intel_th: msu: Fix overflow in shift of an unsigned int intel_th: msu: Fix missing allocation failure check on a kstrndup intel_th: msu: Fix an uninitialized mutex intel_th: gth: Fix the window switching sequence soundwire: slave: fix scanf format soundwire: intel: fix intel_register_dai PDI offsets and numbers interconnect: Add locking in icc_set_tag() interconnect: qcom: Fix icc_onecell_data allocation soundwire: depend on ACPI || OF soundwire: depend on ACPI thunderbolt: Drop unnecessary read when writing LC command in Ice Lake thunderbolt: Fix lockdep circular locking depedency warning thunderbolt: Read DP IN adapter first two dwords in one go
-
git://git.infradead.org/users/hch/configfsLinus Torvalds authored
Pull configfs regression fix from Christoph Hellwig: "Fix a regression from this merge window in the configfs symlink handling (Honggang Li)" * tag 'configfs-for-5.4-2' of git://git.infradead.org/users/hch/configfs: configfs: calculate the depth of parent item
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "A small set of fixes for x86: - Make the tsc=reliable/nowatchdog command line parameter work again. It was broken with the introduction of the early TSC clocksource. - Prevent the evaluation of exception stacks before they are set up. This causes a crash in dumpstack because the stack walk termination gets screwed up. - Prevent a NULL pointer dereference in the rescource control file system. - Avoid bogus warnings about APIC id mismatch related to the LDR which can happen when the LDR is not in use and therefore not initialized. Only evaluate that when the APIC is in logical destination mode" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/tsc: Respect tsc command line paraemeter for clocksource_tsc_early x86/dumpstack/64: Don't evaluate exception stacks before setup x86/apic/32: Avoid bogus LDR warnings x86/resctrl: Prevent NULL pointer dereference when reading mondata
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fixes from Thomas Gleixner: "A small set of fixes for timekeepoing and clocksource drivers: - VDSO data was updated conditional on the availability of a VDSO capable clocksource. This causes the VDSO functions which do not depend on a VDSO capable clocksource to operate on stale data. Always update unconditionally. - Prevent a double free in the mediatek driver - Use the proper helper in the sh_mtu2 driver so it won't attempt to initialize non-existing interrupts" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: timekeeping/vsyscall: Update VDSO data unconditionally clocksource/drivers/sh_mtu2: Do not loop using platform_get_irq_by_name() clocksource/drivers/mediatek: Fix error handling
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull scheduler fixes from Thomas Gleixner: "Two fixes for scheduler regressions: - Plug a subtle race condition which was introduced with the rework of the next task selection functionality. The change of task properties became unprotected which can be observed inconsistently causing state corruption. - A trivial compile fix for CONFIG_CGROUPS=n" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched: Fix pick_next_task() vs 'change' pattern race sched/core: Fix compilation error when cgroup not selected
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf tooling fixes from Thomas Gleixner: - Fix the time sorting algorithm which was broken due to truncation of big numbers - Fix the python script generator fail caused by a broken tracepoint array iterator * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf tools: Fix time sorting perf tools: Remove unused trace_find_next_event() perf scripting engines: Iterate on tep event arrays directly
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq fixlet from Thomas Gleixner: "A trivial fix for a kernel doc regression where an argument change was not reflected in the documentation" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irq/irqdomain: Update __irq_domain_alloc_fwnode() function documentation
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull stacktrace fix from Thomas Gleixner: "A small fix for a stacktrace regression. Saving a stacktrace for a foreign task skipped an extra entry which makes e.g. the output of /proc/$PID/stack incomplete" * 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: stacktrace: Don't skip first entry on noncurrent tasks
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs fix from Steve French: "Small fix for an smb3 reconnect bug (also marked for stable)" * tag '5.4-rc7-smb3-fix' of git://git.samba.org/sfrench/cifs-2.6: SMB3: Fix persistent handles reconnect
-
Corentin Labbe authored
config option GENERIC_IO was removed but still selected by lib/kconfig This patch finish the cleaning. Fixes: 9de8da47 ("kconfig: kill off GENERIC_IO option") Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlLinus Torvalds authored
Pull pin control fixes from Linus Walleij: - Fix glitch risks in the Intel GPIO - Fix the Intel Cherryview valid irq mask calculation. - Allocate the Intel Cherryview irqchip dynamically. - Fix the valid mask init sequency on the ST STMFX driver. * tag 'pinctrl-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: pinctrl: stmfx: fix valid_mask init sequence pinctrl: cherryview: Allocate IRQ chip dynamic pinctrl: cherryview: Fix irq_valid_mask calculation pinctrl: intel: Avoid potential glitches if pin is in GPIO mode
-
- 09 Nov, 2019 8 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linuxLinus Torvalds authored
Pull btrfs fixes from David Sterba: "A few regressions and fixes for stable. Regressions: - fix a race leading to metadata space leak after task received a signal - un-deprecate 2 ioctls, marked as deprecated by mistake Fixes: - fix limit check for number of devices during chunk allocation - fix a race due to double evaluation of i_size_read inside max() macro, can cause a crash - remove wrong device id check in tree-checker" * tag 'for-5.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: btrfs: un-deprecate ioctls START_SYNC and WAIT_SYNC btrfs: save i_size to avoid double evaluation of i_size_read in compress_file_range Btrfs: fix race leading to metadata space leak after task received signal btrfs: tree-checker: Fix wrong check on max devid btrfs: Consider system chunk array size for new SYSTEM chunks
-
git://www.linux-watchdog.org/linux-watchdogLinus Torvalds authored
Pull watchdog fixes from Wim Van Sebroeck: - cpwd: fix build regression - pm8916_wdt: fix pretimeout registration flow - meson: Fix the wrong value of left time - imx_sc_wdt: Pretimeout should follow SCU firmware format - bd70528: Add MODULE_ALIAS to allow module auto loading * tag 'linux-watchdog-5.4-rc7' of git://www.linux-watchdog.org/linux-watchdog: watchdog: bd70528: Add MODULE_ALIAS to allow module auto loading watchdog: imx_sc_wdt: Pretimeout should follow SCU firmware format watchdog: meson: Fix the wrong value of left time watchdog: pm8916_wdt: fix pretimeout registration flow watchdog: cpwd: fix build regression
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) BPF sample build fixes from Björn Töpel 2) Fix powerpc bpf tail call implementation, from Eric Dumazet. 3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet. 4) Fix crash in ebtables when using dnat target, from Florian Westphal. 5) Fix port disable handling whne removing bcm_sf2 driver, from Florian Fainelli. 6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski. 7) Various KCSAN fixes all over the networking, from Eric Dumazet. 8) Memory leaks in mlx5 driver, from Alex Vesker. 9) SMC interface refcounting fix, from Ursula Braun. 10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu. 11) Add a TX lock to synchonize the kTLS TX path properly with crypto operations. From Jakub Kicinski. 12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano Garzarella. 13) Infinite loop in Intel ice driver, from Colin Ian King. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits) ixgbe: need_wakeup flag might not be set for Tx i40e: need_wakeup flag might not be set for Tx igb/igc: use ktime accessors for skb->tstamp i40e: Fix for ethtool -m issue on X722 NIC iavf: initialize ITRN registers with correct values ice: fix potential infinite loop because loop counter being too small qede: fix NULL pointer deref in __qede_remove() net: fix data-race in neigh_event_send() vsock/virtio: fix sock refcnt holding during the shutdown net: ethernet: octeon_mgmt: Account for second possible VLAN header mac80211: fix station inactive_time shortly after boot net/fq_impl: Switch to kvmalloc() for memory allocation mac80211: fix ieee80211_txq_setup_flows() failure path ipv4: Fix table id reference in fib_sync_down_addr ipv6: fixes rt6_probe() and fib6_nh->last_probe init net: hns: Fix the stray netpoll locks causing deadlock in NAPI path net: usb: qmi_wwan: add support for DW5821e with eSIM support CDC-NCM: handle incomplete transfer of MTU nfc: netlink: fix double device reference drop NFC: st21nfca: fix double free ...
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull block fixes from Jens Axboe: - Two NVMe device removal crash fixes, and a compat fixup for for an ioctl that was introduced in this release (Anton, Charles, Max - via Keith) - Missing error path mutex unlock for drbd (Dan) - cgroup writeback fixup on dead memcg (Tejun) - blkcg online stats print fix (Tejun) * tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block: cgroup,writeback: don't switch wbs immediately on dead wbs if the memcg is dead block: drbd: remove a stray unlock in __drbd_send_protocol() blkcg: make blkcg_print_stat() print stats only for online blkgs nvme: change nvme_passthru_cmd64 to explicitly mark rsvd nvme-multipath: fix crash in nvme_mpath_clear_ctrl_paths nvme-rdma: fix a segmentation fault during module unload
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queueDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Fixes 2019-11-08 This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice drivers. Colin Ian King fixes a potentially wrap-around counter in a for-loop. Nick fixes the default ITR values for the iavf driver to 50 usecs interval. Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value cannot be obtained from the firmware, so add X722 to the check to ensure the wrong value is not returned. Jake fixes igb and igc drivers in their implementation of launch time support by declaring skb->tstamp value as ktime_t instead of s64. Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may not be set for AF_XDP sockets that are only used to send packets. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Magnus Karlsson authored
The need_wakeup flag for Tx might not be set for AF_XDP sockets that are only used to send packets. This happens if there is at least one outstanding packet that has not been completed by the hardware and we get that corresponding completion (which will not generate an interrupt since interrupts are disabled in the napi poll loop) between the time we stopped processing the Tx completions and interrupts are enabled again. In this case, the need_wakeup flag will have been cleared at the end of the Tx completion processing as we believe we will get an interrupt from the outstanding completion at a later point in time. But if this completion interrupt occurs before interrupts are enable, we lose it and should at that point really have set the need_wakeup flag since there are no more outstanding completions that can generate an interrupt to continue the processing. When this happens, user space will see a Tx queue need_wakeup of 0 and skip issuing a syscall, which means will never get into the Tx processing again and we have a deadlock. This patch introduces a quick fix for this issue by just setting the need_wakeup flag for Tx to 1 all the time. I am working on a proper fix for this that will toggle the flag appropriately, but it is more challenging than I anticipated and I am afraid that this patch will not be completed before the merge window closes, therefore this easier fix for now. This fix has a negative performance impact in the range of 0% to 4%. Towards the higher end of the scale if you have driver and application on the same core and issue a lot of packets, and towards no negative impact if you use two cores, lower transmission speeds and/or a workload that also receives packets. Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Magnus Karlsson authored
The need_wakeup flag for Tx might not be set for AF_XDP sockets that are only used to send packets. This happens if there is at least one outstanding packet that has not been completed by the hardware and we get that corresponding completion (which will not generate an interrupt since interrupts are disabled in the napi poll loop) between the time we stopped processing the Tx completions and interrupts are enabled again. In this case, the need_wakeup flag will have been cleared at the end of the Tx completion processing as we believe we will get an interrupt from the outstanding completion at a later point in time. But if this completion interrupt occurs before interrupts are enable, we lose it and should at that point really have set the need_wakeup flag since there are no more outstanding completions that can generate an interrupt to continue the processing. When this happens, user space will see a Tx queue need_wakeup of 0 and skip issuing a syscall, which means will never get into the Tx processing again and we have a deadlock. This patch introduces a quick fix for this issue by just setting the need_wakeup flag for Tx to 1 all the time. I am working on a proper fix for this that will toggle the flag appropriately, but it is more challenging than I anticipated and I am afraid that this patch will not be completed before the merge window closes, therefore this easier fix for now. This fix has a negative performance impact in the range of 0% to 4%. Towards the higher end of the scale if you have driver and application on the same core and issue a lot of packets, and towards no negative impact if you use two cores, lower transmission speeds and/or a workload that also receives packets. Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
When implementing launch time support in the igb and igc drivers, the skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t value. Although ktime_t is typedef'd to s64 it wasn't always, and the kernel provides accessors for ktime_t values. Use the ktime_to_timespec64 and ktime_set accessors instead of directly assuming that the variable is always an s64. This improves portability if the code is ever moved to another kernel version, or if the definition of ktime_t ever changes again in the future. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-