In the case where frac_div larger than 96 the result of an unsigned
multiplication overflows an unsigned int.  For example, this can
happen when the sample_rate is 192000 and pll_input is 122.  Fix
this by casing the first term of the mutiply to a u64. Also remove
the extraneous parentheses around the expression.

Addresses-Coverity: ("Unintentional integer overflow")
Fixes: a497a436 ("ASoC: Add support for Conexant CX2072X CODEC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

The A83t and compatibles controllers don't have any reception capabilities
on some instances of the controllers, even though it was never documented
as such in the binding before.

Therefore, on those controllers, we don't have the option to set an RX DMA
channel.

This was already done in the DTSI, but the binding itself was never
updated. Let's add a special case in the schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Allwinner SoCs feature an I2S controller across multiple SoC
generations.

However, earlier generations were a bit simpler than the subsequent ones,
and for example would always have RX and TX capabilities, and no reset
lines.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Current trace implementation gets out of sync when sof device
is put to suspend. The debugfs file handle is kept open, but
firmware will reset its state. After resume, debugfs client's
read offset will not be synchronized to firmware and this may
result in traces read in incorrect order and/or stale data being
read after resume.

Add logic to signal end-of-file to read() when firmware tracing
has ended, and all trace data has been read. This allows debugfs
client to capture all trace data, and reopen the trace file to
ensure proper synchronization with firmware after reopening
the node.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Move duplicated code in sof_wait_trace_avail() to a helper function.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.

So, replace code of the following form:

sizeof(*w) + sizeof(struct sof_ipc_window_elem) * w->num_windows

with:

struct_size(w, window, w->num_windows)

Notice that variable size is unnecessary, hence it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The SEI510 board features a standalone MAX98357A codec.
Add a tristate prompt to allow selecting the codec.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Allwinner H6 has a SPDIF controller with an increase of the fifo
size and a sligher difference in memory mapping compare to H3/A64.

This make it not compatible with the previous generation.

Introduce a specific bindings for H6 SoC.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.

So, replace the following form:

sizeof(struct sof_ipc_ctrl_data) + sizeof(struct sof_ipc_ctrl_value_chan) *
	le32_to_cpu(mc->num_channels)

with:

struct_size(scontrol->control_data, chanv, le32_to_cpu(mc->num_channels))

and so on...

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Variable pulse_len is being initialized to 1 however this value is
never read and pulse_len is being re-assigned later in a switch
statement.  Clean up the code by removing the redundant initialization.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.

So, replace code of the following form:

sizeof(*fwk) + fwk->num_services * sizeof(fwk->svc_api_info[0]);

with:

struct_size(fwk, svc_api_info, fwk->num_services)

and so on...

Notice that variables bytes and len are unnecessary, hence they are
removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.

So, replace the following form:

uuid_params->num_modules * sizeof(struct skl_mod_inst_map) + sizeof(uuid_params->num_modules)

with:

struct_size(params, u.map, uuid_params->num_modules)

and so on...

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with
memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

instance = krealloc(instance, sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, use the new
struct_size() helper:

instance = krealloc(instance, struct_size(instance, entry, count), GFP_KERNEL);

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

We've used a standard interface for machine drivers for some time now,
there is no need for this dependency on a Skylake-specific header
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

mt8183_mt6358_ts3a227_max98357_dev_probe() does not return immediately
if devm_snd_soc_register_card() returns fail.  As a result, the rest of
code still get executed.

Two options to fix:
1. add an extra return statement if devm_snd_soc_register_card()
   returns fail
2. move devm_snd_soc_register_card() to the end of probe

Adopt option 2 which is more clear and common.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Kernel emits the following messages when booting.
ASoC: DAPM unknown pin Headset Mic
ASoC: DAPM unknown pin Headphone

Remove the unused DAPM pins.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

System suspend will power off audio, so we need regcache sync when
system resume.

Remove pm_runtime_get_sync in dev probe and pm_runtime_put_sync in
dev remove.So that audio dev can triggle runitme suspend and resume.
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This is an implementation of a machine driver needed for Conexant
CX2072X codec on Intel Baytrail and Cherrytrail platforms.  The
current patch is based on the initial work by Pierre-Louis Bossart and
the other Intel machine drivers.

The jack detection support (driven via the standard GPIO) was added on
top of the original work.

Tested with ASUS E200HA laptop.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=115531Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Initial commit of the Conexant CX2072X CODEC driver. Some features are
not present.

The CX2072X is a ultra low power stereo audio codec supports I2S/TDM
host interface with EQ, DRC features in playback mode.

Featues of CX2072X codec:

 * Two 24 bits DACs and DACs.
 * Stereo Headphone AMP.
 * 2.8W per channel class-D output.
 * Integrated seven bands per channel EQ and DRC.
 * Fully integrated headset support with detect/switch.
 * Stereo digital microphone for array applications.
 * S/PDIF output.
 * Bi-directional GPIOs.
 * Support analog and digital PC Beeep.
 * One headset button support.
 * Supports a wide variety of host interfaces.
   -wide variety of I2S and similar bit-stream formats
    with word lengths of up to 24 bits.
   -TDM stream supports up to 4 channels.
 * AEC loopback support.

Further fixes by tiwai:
 * Rebase to 5.2+
 * Missing DAPM entry definitions
 * Missing power hooks
 * Fix uninitialized variable warning
 * Rewrite jack detection stuff to use set_jack callback
 * Plumbing jack detection code for Intel ASoC
 * Move clk management into runtime PM
 * Drop incorrect regcache usages
 * Drop untested stuff: OF table, EQ/DRC handling
 * Lots of code cleanups and minor refactoring

The OF code was dropped due to the lack of testability.
It should be easy to re-add once if someone can test it.

v1->v2: No change
v2->v3: Move register tables to appropriate place
	Remove some confusing codes
	Set snd_ctl_boolean_* helpers directly
	Fix EQ put callback
	Rename to "DAC1 Switch" from "DAC1 Mute Switch"
	Drop superfluous regmap calls at shutdown
	Avoid regmap_register_patch()
	Add missing register definitions
	Fix register access on big-endian machine
	Remove regcache messes
v3->v4: Fix the wrong endianess conversion in reg write
	Minor code cleanups
v4->v5: Move clk management to runtime PM
	Sparse warning fixes
	Some more code simplification
	Drop tricky regcache fiddling
	Apply mutex locks around possible racy sequences
	Move exported jack detection stuff into set_jack callback
v5->v6: Drop buggy&untested EQ and DRC codes
	Lots of code reduction/cleanup
	Add more comments about platform-specific stuff

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=115531Signed-off-by: Simon Ho <simon.ho@conexant.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Unify the supported input and output rate, add the
12kHz/24kHz/128kHz to the support list
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-5.3

soc_pcm_components_open/close() try to call
try_module_get()/module_put() based on
component->driver->module_get_upon_open.

Here, the purpose why we need to call these functions are to
checking module reference.
Thus, we need to call try_module_open() even though it doesn't
have .open callback.

The same reason, we need to call module_put() even though it
doesn't have .close

This patch calls try_module_get()/module_put() regardless of
.open/.close
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Make sure quirk handling is cleary split from number of links.
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

mtk_regmap_update_bits() has been changed to take a shift and warn
when reg >= 0 but shift < 0.So the hd_align_mshift must not have shift.
Change it from XXX_HD_ALIGN_MASK_SFT to XXX_HD_ALIGN_MASK.

Fixes: cf61f5b0 ("ASoC: Mediatek: MT8183: set data align")
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

mtk_regmap_update_bits() has been changed from four
parameters to five parameters.

Fixes: 1628fc3f ("ASoC: Mediatek: MT8183: add memory interface data align")
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The use of BIT/GENMASK was incorrect, fix.
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The RT5682 codec button mapping, initially copied from the DA7219 one,
needs to be corrected.
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When configuring a codec to be both bit-clock and frame-master, it was
found that the codec was always configured as bit-clock and frame-slave.
Looking at the simple_dai_link_of() function there appears to be two
problems with the configuration of the DAI format, which are ...

1. The function asoc_simple_parse_daifmt() is called before the function
   asoc_simple_parse_codec() and this means that the device-tree node
   for the codec has not been parsed yet, which is needed by the
   function asoc_simple_parse_daifmt() to determine who is the codec.
2. The phandle passed to asoc_simple_parse_daifmt() is the phandle to
   the 'codec' node and not the phandle of the actual codec defined by
   the 'sound-dai' property under the 'codec' node.

Fix the above by moving the call to asoc_simple_parse_daifmt() after the
the call to asoc_simple_parse_codec() and pass the phandle for the codec
to asoc_simple_parse_daifmt().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add reset-gpios property, which is optional.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

soc_probe_component() has WARN() under if (component->driver->probe),
but, this WARN() check is not related to .probe callback.
So, it should be called at (B) instead of (A).
This patch moves it out of if().

	if (component->driver->probe) {
		ret = component->driver->probe(component);
		...
(A)		WARN(...)
	}
(B)	WARN(...)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

snd_soc_dai_driver :: pcm_new has snd_soc_dai as parameter, but
snd_soc_component_driver :: pcm_new doesn't have it.

rsnd driver needs snd_soc_dai at pcm_new.
This patch moves .pcm_new from snd_soc_component_driver to
snd_soc_dai_driver, and don't use rtd->cpu_dai anymore.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Assign button functions based on Android wired headset specs(v1.1).
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

IIR fileter can remove DC offset. It must be enabled when
dmic or amic connected to pmic is used.
Signed-off-by: Shunli Wang <shunli.wang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

include/linux/fs.h defines a bunch of simple fs helpers, (e.g.
simple_rename) and we intend to add an fs helper named simple_remove.

Rename the ASoC driver static functions, so they will not collide with
the upcoming fs helper function name.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The selection order of m/c in match table is corrected
to use common codec as last in the list.
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

There is a case when a we want to read a large number of bytes that
require a burst but is not a multiple of the word size (8). When this
happens rt5677_spi_reverse will run off the end of the buffer. The
solution is to tell spi_reverse the actual size of the destination and
stop if we reach it even if we have data left that we read.

Cc: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

snd_soc_dai_link_event() is updating snd_soc_dai :: active,
but it is unbalance.
It counts up if it has startup callback.

	case SND_SOC_DAPM_PRE_PMU:
		...
		snd_soc_dapm_widget_for_each_source_path(w, path) {
			...
			if (source->driver->ops->startup) {
				...
=>				source->active++;
			}
			...
		}
		...

But, always counts down

	case SND_SOC_DAPM_PRE_PMD:
		...
		snd_soc_dapm_widget_for_each_source_path(w, path) {
			...
=>			source->active--;
			...
		}

This patch always counts up when SND_SOC_DAPM_PRE_PMD.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Linux 5.2-rc1

Pull UBIFS fixes from Richard Weinberger:

 - build errors wrt xattrs

 - mismerge which lead to a wrong Kconfig ifdef

 - missing endianness conversion

* tag 'upstream-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
  ubifs: Convert xattr inum to host order
  ubifs: Use correct config name for encryption
  ubifs: Fix build error without CONFIG_UBIFS_FS_XATTR