- 14 Mar, 2016 35 commits
-
-
Grygorii Strashko authored
tps65910 RTC IRQ is nested threaded and wired to the tps65910 inerrupt controller. So, this flag is not required for nested irqs anymore, since commit 3c646f2c ("genirq: Don't suspend nested_thread irqs over system suspend") was merged. Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Tony Lindgren <tony@atomide.com> Cc: Nishanth Menon <nm@ti.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com>
-
Grygorii Strashko authored
tps6586x RTC IRQ is nested threaded and wired to the tps6586x inerrupt controller. So, this flag is not required for nested irqs anymore, since commit 3c646f2c ("genirq: Don't suspend nested_thread irqs over system suspend") was merged. Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Nishanth Menon <nm@ti.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by:
-
Grygorii Strashko authored
Palams RTC IRQ is nested threaded and wired to the Palmas inerrupt controller. So, this flag is not required for nested irqs anymore, since commit 3c646f2c ("genirq: Don't suspend nested_thread irqs over system suspend") was merged. Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Nishanth Menon <nm@ti.com> Signed-off-by:
-
Soren Brinkmann authored
The RTC entries are mostly grouped by vendor. Move the few outliers in place. Also, change the one occurrence of 'nxp' to 'NXP' to make all NXP entries consistent. Signed-off-by:
Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by:
-
Joshua Henderson authored
This driver adds support for the PIC32 real time clock and calendar peripheral: - reading and setting time - alarms provided by dedicated IRQ Signed-off-by:
Joshua Henderson <joshua.henderson@microchip.com> Signed-off-by:
-
Joshua Henderson authored
Document the devicetree bindings for the real time clock found on Microchip PIC32 class devices. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Akinobu Mita authored
The alarm for rx8025 only has a minute accuracy, so unsupport UIE mode. pcf8563 and hym8563 also have a minute accuracy and unsupport it. Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
-
Akinobu Mita authored
The alarm for rx8025 only has a minute accuracy, so round up to nearest minute when setting alarm. Without doing this, rtctest blocks one day after setting alarm to 5 seconds later. pcf8563 and hym8563 also have similar handling. Signed-off-by:
-
Akinobu Mita authored
The ctrl1 register is accessed by alarm operations. But it is updated in threaded interrupt handler without acquiring rtc->ops_lock. Signed-off-by:
-
Akinobu Mita authored
When IRQ line for this chips is connected, devm_request_threaded_irq() refuses to register irq handler with the following message. genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq Signed-off-by:
-
Krzysztof Kozlowski authored
Few functions were marked inline even though they were relatively large and sometimes used in multiple places. De-inline them to let the compiler decide whether optimization makes sense. This fixes inline_hunt report: drivers/rtc/rtc-s5m.c: Deinline s5m8767_rtc_set_alarm_reg, save 704 bytes drivers/rtc/rtc-s5m.c: Deinline s5m8767_wait_for_udr_update, save 192 bytes Reported-by:
Denys Vlasenko <vda.linux@googlemail.com> Cc: Denys Vlasenko <vda.linux@googlemail.com> Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
-
Paul Gortmaker authored
The Makefile/Kconfig currently controlling compilation of this code is: obj-$(CONFIG_RTC_CLASS) += rtc-core.o rtc-core-y := class.o interface.o drivers/rtc/Kconfig:menuconfig RTC_CLASS drivers/rtc/Kconfig: bool "Real Time Clock" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the code there is no doubt it is builtin-only. We don't replace module.h with init.h since the file does need to know what a struct module is. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Signed-off-by:
Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by:
-
Juergen Borleis authored
When setting a new time/date the RTC's clock must be stopped first, in order to write the time/date registers in an atomic manner. So, this change stops the clock first and then writes the time/date registers and the clock control register (to re-enable the clock) in one turn. Signed-off-by:
Juergen Borleis <jbe@pengutronix.de> Signed-off-by:
-
Juergen Borleis authored
Check if the RTC signals an invalid time/date (due to a battery power loss for example). In this case ignore the time/date until it is really set again. Signed-off-by:
-
Juergen Borleis authored
By using i2c_smbus_read_i2c_block_data() the code is now much simpler. While at it: when reading the RTC's seconds register, all time/date registers are frozen until the RTC's year register is read. So it is important to read all time/date registers in one turn to not lose a second event. Make it more clear why the read must happen in this way. Signed-off-by:
-
Joshua Clayton authored
pcf2123 has an offset register, which can be used to make minor adjustments to the clock rate to compensate for temperature or a crystal that is not exactly right. Signed-off-by:
Joshua Clayton <stillcompiling@gmail.com> Signed-off-by:
-
Joshua Clayton authored
clock offset may be set and read in decimal parts per billion attribute is /sys/class/rtc/rtcN/offset The attribute is only visible for rtcs that have set_offset implemented. Signed-off-by:
-
Joshua Clayton authored
A number of rtc devices, such as the NXP pcf2123 include a facility to adjust the clock in order to compensate for temperature or a crystal, capacitor, etc, that results in the rtc clock not running at exactly 32.768 kHz. Data sheets I have seen refer to this as a clock offset, and measure it in parts per million, however they often reference ppm to 2 digits of precision, which makes integer ppm less than ideal. We use parts per billion, which more than covers the precision needed and works nicely within 32 bits Signed-off-by:
-
Oleksij Rempel authored
Fix a scheduling while atomic issue caused by rv8803_set_time() holding a spinlock during the call to i2c_smbus_read_byte_data(). Signed-off-by:
Oleksij Rempel <fixed-term.Oleksij.Rempel@de.bosch.com> Signed-off-by:
-
Oleksij Rempel authored
Document Alphascale asm9260 RTC bindings Signed-off-by:
Oleksij Rempel <linux@rempel-privat.de> Acked-by:
-
Oleksij Rempel authored
Add support for RTC controller found on Alphascale asm9260 SoC. Signed-off-by:
-
Akinobu Mita authored
DS3231 has programmable square-wave output signal. This enables to use this feature as a clock provider of common clock framework. Signed-off-by:
Michael Turquette <mturquette@baylibre.com> Signed-off-by:
-
Laxman Dewangan authored
To make RTC block of MAX77686/MAX77802 as independent driver, move the registration of i2c device, regmap for register access and irq_chip for interrupt support inside the RTC driver. Removed the same initialisation from MFD driver. Having this change will allow to reuse this driver for different PMIC/devices from Maxim Semiconductor if they kept same RTC IP on different PMIC. Some of examples as PMIC MAX77620, MAX20024 where same RTC IP used and hence driver for these chips will use this driver only for RTC support. Suggested-by:
Laxman Dewangan <ldewangan@nvidia.com> Tested-by:
Lee Jones <lee.jones@linaro.org> Tested-by:
-
Laxman Dewangan authored
There is different RTC I2C address for RTC block in MAX77686. Driver is creating dummy i2c client for this address to access the register of this IP block. As there is no call to i2c_get_clientdata() for rtc_i2c client, there is no need to store pointer and hence removing the call to set client data for rtc i2c client. Suggested-by:
-
Laxman Dewangan authored
Get rid of referring parent device info for register access all the places by making regmap as part of max77686 rtc device info. This will also remove the need of storing parent device info in max77686 rtc device info as this is no more required. Signed-off-by:
-
Laxman Dewangan authored
rtc_regmap should be used to access all RTC registers instead of parent regmap regardless of what chip or property have it. This makes the register access uniform and extendible for other chips. Signed-off-by:
-
Laxman Dewangan authored
Fix following check patch error in rtc-max77686 driver: - Alignment should match open parenthesis. - braces {} should be used on all arms of this statement. - Prefer using the BIT macro Signed-off-by: -
Andre Przywara authored
At the moment the "sun6i" RTC drivers depends on having two specific SoC families selected. The Allwinner A64 SoC has the same RTC, so extend the Kconfig option to allow inclusion of the driver for all Allwinner SoCs. Signed-off-by:
Andre Przywara <andre.przywara@arm.com> Acked-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
-
Steffen Trumtrar authored
The RX6110 comes in two different variants: SPI and I2C. This driver only supports the SPI variant. If the need ever arises to also support the I2C variant, this driver could easily be refactored to support both cases. Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by:
-
Steffen Trumtrar authored
Add the binding documentation for the Epson RX6110 RTC. Acked-by:
-
Joshua Clayton authored
pcf2123 data sheet recommends a software reset when the chip is first powered on. This change avoids resetting the chip every time the driver is loaded, which has some negative effects. There are several registers including a clock rate adjustment that really should survive a reload of the driver (or reboot). In addition, stopping and restarting the clock to verify the chip is there is not a good thing once the time is set. According to the data sheet, the seconds register has a 1 in the high bit when the voltage has gotten low. We check for this condition, as well as whether the time retrieved from the chip is valid. We reset the rtc only if the time is not reliable and valid. This is sufficient for checking for the presence of the chip, as either all zeros or all 0xff will result in an invalid time/date Signed-off-by:
-
Joshua Clayton authored
Refactor chip reset items into its own function, isolating it from the rest of the device probe. Subsequent commits will avoid calling this code. Signed-off-by:
-
Joshua Clayton authored
Add new functions pcf2123_write(), and pcf2123_write_reg(). Use named defines for the values being written. This improves modularity and readability, and reduces lines of code. Signed-off-by:
-
Joshua Clayton authored
Put read operations into a function. This improves modularity and readability. Signed-off-by:
-
Joshua Clayton authored
Add defines for all 16 registers in the pcf2123. Add defines for useful bits from several registers I've tried to document all the registers, and as best as possible, all the special bits they employ Use BIT() wherever possible in the bit definitions Signed-off-by:
-
- 04 Feb, 2016 5 commits
-
-
Akinobu Mita authored
DS3231 has the temperature registers with a resolution of 0.25 degree celsius. This enables to get the value through hwmon. # cat /sys/class/i2c-adapter/i2c-2/2-0068/hwmon/hwmon0/temp1_input 21000 Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Michael Lange authored
For RTC chips with no IRQ directly connected to the SoC, the RTC chip can be forced as a wakeup source by stating that explicitly in the device's .dts file using the "wakeup-source" boolean property. This will guarantee the 'wakealarm' sysfs entry is available on the device, if supported by the RTC. With these changes to the driver rtc-ds1307 and the necessary entries in the .dts file, I get an working ds1337 RTC on the Witty Pi extension board by UUGear for the Raspberry Pi. An example for the entry in the .dts file: rtc: ds1337@68 { compatible = "dallas,ds1337"; reg = <0x68>; wakeup-source; If the "wakeup-source" property is set, do not request an IRQ. Set also UIE mode to unsupported, to get a working 'hwclock' binary. Signed-off-by:Michael Lange <linuxstuff@milaw.biz> Signed-off-by:
-
Arnd Bergmann authored
The mt6397 RTC driver can be built either when the MFD_MT6397 driver is enabled (which selects IRQ_DOMAIN), or when compile testing. The latter however fails without IRQ domains: drivers/rtc/rtc-mt6397.c: In function 'mtk_rtc_probe': drivers/rtc/rtc-mt6397.c:326:13: error: implicit declaration of function 'irq_create_mapping' [-Werror=implicit-function-declaration] rtc->irq = irq_create_mapping(mt6397_chip->irq_domain, res->start); This adds an explicit dependency for the COMPILE_TEST case. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Eddie Huang <eddie.huang@mediatek.com> Signed-off-by:
-
Alexandre Belloni authored
The rv8803 has its own driver that should be used. Remove its id from the rx8025 driver. Fixes: b1f9d790Signed-off-by:
-
Geliang Tang authored
For better readability, use to_spi_device() and kobj_to_dev() instead of container_of(). Signed-off-by:
Geliang Tang <geliangtang@163.com> Signed-off-by:
-
