- 11 Dec, 2020 16 commits
-
-
Ilan Peer authored
When custom regulatory was set, only the channels setting was updated, but the regulatory domain was not saved. Fix it by saving it. Signed-off-by:
Ilan Peer <ilan.peer@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20201129172929.290fa5c5568a.Ic5732aa64de6ee97ae3578bd5779fc723ba489d1@changeidSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Avraham Stern authored
Accept a scan request with the duration set even if the driver does not support setting the scan dwell. The duration can be used as a hint to the driver, but the driver may use its internal logic for setting the scan dwell. Signed-off-by:
Avraham Stern <avraham.stern@intel.com> Signed-off-by:
-
Ilan Peer authored
When a new BSS entry is created based on multi BSS IE, the TSF and the TSF BSSID were not updated. Fix it. Signed-off-by:
-
Ayala Beker authored
In case of scan request with wildcard SSID, or in case of more than one SSID in scan request, need to scan PSC channels even though all the co-located APs found during the legacy bands scan indicated that all the APs in their ESS are co-located, as we might find different networks on the PSC channels. Signed-off-by:
Ayala Beker <ayala.beker@intel.com> Signed-off-by:
-
Ilan Peer authored
When parsing supported rates IE. Signed-off-by:
-
Ilan Peer authored
This extends the support for drivers that rebuild IEs in the FW (same as with HT/VHT/HE). Signed-off-by:
-
Johannes Berg authored
Support the driver incrementing MIC error and replay detected counters when having detected a bad frame, if it drops it directly instead of relying on mac80211 to do the checks. These are then exposed to userspace, though currently only in some cases and in debugfs. Signed-off-by:
-
Shaul Triebitz authored
ack_enabled and multi_sta_back_32bit are station capabilities and should not be in the bss_conf structure. Signed-off-by:
Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by:
-
Tom Rix authored
The macro uses should have (and already have) the semicolon. Signed-off-by:
Tom Rix <trix@redhat.com> Link: https://lore.kernel.org/r/20201127193842.2876355-1-trix@redhat.comSigned-off-by:
-
Gustavo A. R. Silva authored
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning by explicitly adding a break statement instead of letting the code fall through to the next case. Link: https://github.com/KSPP/linux/issues/115Signed-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Link: https://lore.kernel.org/r/fe5afd456a1244751177e53359d3dd149a63a873.1605896060.git.gustavoars@kernel.orgSigned-off-by:
-
Gustavo A. R. Silva authored
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple warnings by explicitly adding multiple break statements instead of letting the code fall through to the next case. Link: https://github.com/KSPP/linux/issues/115Signed-off-by:
-
Gustavo A. R. Silva authored
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning by explicitly adding a break statement instead of letting the code fall through to the next case. Link: https://github.com/KSPP/linux/issues/115Signed-off-by:
-
Sami Tolvanen authored
Instead of casting callback functions to type iw_handler, which trips indirect call checking with Clang's Control-Flow Integrity (CFI), add stub functions with the correct function type for the callbacks. Reported-by:
Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by:
Sami Tolvanen <samitolvanen@google.com> Reviewed-by:
Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20201117205902.405316-1-samitolvanen@google.comSigned-off-by:
-
Colin Ian King authored
Don't populate the const array bws on the stack but instead it static. Makes the object code smaller by 80 bytes: Before: text data bss dec hex filename 85694 16865 1216 103775 1955f ./net/wireless/reg.o After: text data bss dec hex filename 85518 16961 1216 103695 1950f ./net/wireless/reg.o (gcc version 10.2.0) Signed-off-by:
Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20201116181636.362729-1-colin.king@canonical.comSigned-off-by:
-
Lev Stipakov authored
Commits d3fd6548 ("net: core: add dev_sw_netstats_tx_add") 451b05f4 ("net: netdevice.h: sw_netstats_rx_add helper) have added API to update net device per-cpu TX/RX stats. Use core API instead of ieee80211_tx/rx_stats(). Signed-off-by:
Lev Stipakov <lev@openvpn.net> Reviewed-by:
Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/20201113214623.144663-1-lev@openvpn.netSigned-off-by:
-
Emmanuel Grumbach authored
The WLAN device may exist yet not be usable. This can happen when the WLAN device is controllable by both the host and some platform internal component. We need some arbritration that is vendor specific, but when the device is not available for the host, we need to reflect this state towards the user space. Add a reason field to the rfkill object (and event) so that userspace can know why the device is in rfkill: because some other platform component currently owns the device, or because the actual hw rfkill signal is asserted. Capable userspace can now determine the reason for the rfkill and possibly do some negotiation on a side band channel using a proprietary protocol to gain ownership on the device in case the device is owned by some other component. When the host gains ownership on the device, the kernel can remove the RFKILL_HARD_BLOCK_NOT_OWNER reason and the hw rfkill state will be off. Then, the userspace can bring the device up and start normal operation. The rfkill_event structure is enlarged to include the additional byte, it is now 9 bytes long. Old user space will ask to read only 8 bytes so that the kernel can know not to feed them with more data. When the user space writes 8 bytes, new kernels will just read what is present in the file descriptor. This new byte is read only from the userspace standpoint anyway. If a new user space uses an old kernel, it'll ask to read 9 bytes but will get only 8, and it'll know that it didn't get the new state. When it'll write 9 bytes, the kernel will again ignore this new byte which is read only from the userspace standpoint. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Link: https://lore.kernel.org/r/20201104134641.28816-1-emmanuel.grumbach@intel.comSigned-off-by:
-
- 10 Dec, 2020 24 commits
-
-
David S. Miller authored
Tom Parkin says: ==================== add ppp_generic ioctl(s) to bridge channels Following on from my previous RFC[1], this series adds two ioctl calls to the ppp code to implement "channel bridging". When two ppp channels are bridged, frames presented to ppp_input() on one channel are passed to the other channel's ->start_xmit function for transmission. The primary use-case for this functionality is in an L2TP Access Concentrator where PPP frames are typically presented in a PPPoE session (e.g. from a home broadband user) and are forwarded to the ISP network in a PPPoL2TP session. The two new ioctls, PPPIOCBRIDGECHAN and PPPIOCUNBRIDGECHAN form a symmetric pair. Userspace code testing and illustrating use of the ioctl calls is available in the go-l2tp[2] and l2tp-ktest[3] repositories. [1]. Previous RFC series: https://lore.kernel.org/netdev/20201106181647.16358-1-tparkin@katalix.com/ [2]. go-l2tp: a Go library for building L2TP applications on Linux systems. Support for the PPPIOCBRIDGECHAN ioctl is on a branch: https://github.com/katalix/go-l2tp/tree/tp_002_pppoe_2 [3]. l2tp-ktest: a test suite for the Linux Kernel L2TP subsystem. Support for the PPPIOCBRIDGECHAN ioctl is on a branch: https://github.com/katalix/l2tp-ktest/tree/tp_ac_pppoe_tests_2 Changelog: v4: * Fix NULL-pointer access in PPPIOCBRIDGECHAN in the case that the ID of the channel to be bridged wasn't found. * Add comment in ppp_unbridge_channels to better document the unbridge process. v3: * Use rcu_dereference_protected for accessing struct channel 'bridge' field during updates with lock 'upl' held. * Avoid race in ppp_unbridge_channels by ensuring that each channel in the bridge points to it's peer before decrementing refcounts. v2: * Add missing __rcu annotation to struct channel 'bridge' field in order to squash a sparse warning from a C=1 build * Integrate review comments from gnault@redhat.com * Have ppp_unbridge_channels return -EINVAL if the channel isn't part of a bridge: this better aligns with the return code from ppp_disconnect_channel. * Improve docs update by including information on ioctl arguments and error return codes. ==================== Reviewed-by:
Guillaume Nault <gnault@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Tom Parkin authored
Add documentation of the newly-added PPPIOCBRIDGECHAN and PPPIOCUNBRIDGECHAN ioctls. Signed-off-by:
Tom Parkin <tparkin@katalix.com> Signed-off-by:
-
Tom Parkin authored
This new ioctl pair allows two ppp channels to be bridged together: frames arriving in one channel are transmitted in the other channel and vice versa. The practical use for this is primarily to support the L2TP Access Concentrator use-case. The end-user session is presented as a ppp channel (typically PPPoE, although it could be e.g. PPPoA, or even PPP over a serial link) and is switched into a PPPoL2TP session for transmission to the LNS. At the LNS the PPP session is terminated in the ISP's network. When a PPP channel is bridged to another it takes a reference on the other's struct ppp_file. This reference is dropped when the channels are unbridged, which can occur either explicitly on userspace calling the PPPIOCUNBRIDGECHAN ioctl, or implicitly when either channel in the bridge is unregistered. In order to implement the channel bridge, struct channel is extended with a new field, 'bridge', which points to the other struct channel making up the bridge. This pointer is RCU protected to avoid adding another lock to the data path. To guard against concurrent writes to the pointer, the existing struct channel lock 'upl' coverage is extended rather than adding a new lock. The 'upl' lock is used to protect the existing unit pointer. Since the bridge effectively replaces the unit (they're mutually exclusive for a channel) it makes coding easier to use the same lock to cover them both. Signed-off-by:
-
Jakub Kicinski authored
We use rcu_assign_pointer to assign both the table and the entries, but the entries are not marked as __rcu. This generates sparse warnings. Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
-
Willy Tarreau authored
This reverts commit 0a4e9ce1. The code was developed and tested on an MSC313E SoC, which seems to be half-way between the AT91RM9200 and the AT91SAM9260 in that it supports both the 2-descriptors mode and a Tx ring. It turns out that after the code was merged I could notice that the controller would sometimes lock up, and only when dealing with sustained bidirectional transfers, in which case it would report a Tx overrun condition right after having reported being ready, and will stop sending even after the status is cleared (a down/up cycle fixes it though). After adding lots of traces I couldn't spot a sequence pattern allowing to predict that this situation would happen. The chip comes with no documentation and other bits are often reported with no conclusive pattern either. It is possible that my change is wrong just like it is possible that the controller on the chip is bogus or at least unpredictable based on existing docs from other chips. I do not have an RM9200 at hand to test at the moment and a few tests run on a more recent 9G20 indicate that this code path cannot be used there to test the code on a 3rd platform. Since the MSC313E works fine in the single-descriptor mode, and that people using the old RM9200 very likely favor stability over performance, better revert this patch until we can test it on the original platform this part of the driver was written for. Note that the reverted patch was actually tested on MSC313E. Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Daniel Palmer <daniel@0x0f.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/netdev/20201206092041.GA10646@1wt.eu/Signed-off-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
-
Subash Abhinov Kasiviswanathan authored
Packets sent by rmnet to the real device have variable MAP header lengths based on the data format configured. This patch adds checks to ensure that the real device MTU is sufficient to transmit the MAP packet comprising of the MAP header and the IP packet. This check is enforced when rmnet devices are created and updated and during MTU updates of both the rmnet and real device. Additionally, rmnet devices now have a default MTU configured which accounts for the real device MTU and the headroom based on the data format. Signed-off-by:
Sean Tranchetti <stranche@codeaurora.org> Signed-off-by:
Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Tested-by:
Loic Poulain <loic.poulain@linaro.org> Signed-off-by:
-
Xie He authored
When the upper layer instruct us to connect (or disconnect), but we have already connected (or disconnected), consider this operation successful rather than failed. This can help the upper layer to correct its record about whether we are connected or not here in layer 2. The upper layer may not have the correct information about whether we are connected or not. This can happen if this driver has already been running for some time when the "x25" module gets loaded. Another X.25 driver (hdlc_x25) is already doing this, so we make this driver do this, too. Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by:
Xie He <xie.he.0141@gmail.com> Acked-by:
Martin Schiller <ms@dev.tdt.de> Signed-off-by:
-
Sasha Neftin authored
Add new device ID for the next step of the silicon and reflect the I226_K part. Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by:
-
Arjun Roy authored
A prior patch increased the size of struct tcp_zerocopy_receive but did not update do_tcp_getsockopt() handling to properly account for this. This patch simply reintroduces content erroneously cut from the referenced prior patch that handles the new struct size. Fixes: 18fb76ed ("net-zerocopy: Copy straggler unaligned data for TCP Rx. zerocopy.") Signed-off-by:
Arjun Roy <arjunroy@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
Zheng Yongjun authored
Simplify the return expression. Signed-off-by:
Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by:
-
Zheng Yongjun authored
Simplify the return expression. Signed-off-by:
-
Zheng Yongjun authored
Simplify the return expression. Signed-off-by:
-
David S. Miller authored
Merge tag 'linux-can-next-for-5.11-20201210' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2020-12-10 here's a pull request of 7 patches for net-next/master. The first patch is by Oliver Hartkopp for the CAN ISOTP, which adds support for functional addressing. A patch by Antonio Quartulli removes an unneeded unlikely() annotation from the rx-offload helper. The next three patches target the m_can driver. Sean Nyekjaers's patch removes a double clearing of clock stop request bit, Patrik Flykt's patch moves the runtime PM enable/disable to m_can_platform and Jarkko Nikula's patch adds a PCI glue code driver. Fabio Estevam's patch converts the flexcan driver to DT only. And Manivannan Sadhasivam's patchd for the mcp251xfd driver adds internal loopback mode support. ==================== Signed-off-by:
-
Antonio Quartulli authored
The definition of IS_ERR() already applies the unlikely() notation when checking the error status of the passed pointer. For this reason there is no need to have the same notation outside of IS_ERR() itself. Clean up code by removing redundant notation. Signed-off-by:
Antonio Quartulli <a@unstable.cc> Signed-off-by:
-
Manivannan Sadhasivam authored
MCP251xFD supports internal loopback mode which can be used to verify CAN functionality in the absence of a real CAN device. Link: https://lore.kernel.org/r/20201201054019.11012-1-manivannan.sadhasivam@linaro.orgSigned-off-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> [mkl: mcp251xfd_get_normal_mode(): move CAN_CTRLMODE_LOOPBACK check to front] Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Fabio Estevam authored
The flexcan driver runs only on DT platforms, so simplify the code by using of_device_get_match_data() to retrieve the driver data and also by removing the unused id_table. Signed-off-by:
Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20201128132855.7724-1-festevam@gmail.comSigned-off-by:
-
Jarkko Nikula authored
Add support for M_CAN controller on Intel Elkhart Lake attached to the PCI bus. It integrates the Bosch M_CAN controller with Message RAM and the wrapper IP block with additional registers which all of them are within the same MMIO range. Currently only interrupt control register from wrapper IP is used and the MRAM configuration is expected to come from the firmware via "bosch,mram-cfg" device property and parsed by m_can.c core. Initial implementation is done by Felipe Balbi while he was working at Intel with later changes from Raymond Tan and me. Co-developed-by:
Felipe Balbi (Intel) <balbi@kernel.org> Co-developed-by:
Raymond Tan <raymond.tan@intel.com> Signed-off-by:
Jarkko Nikula <jarkko.nikula@linux.intel.com> Link: https://lore.kernel.org/r/20201117160827.3636264-1-jarkko.nikula@linux.intel.comSigned-off-by:
-
Patrik Flykt authored
This is a preparatory patch for upcoming PCI based M_CAN devices. The current PM implementation would cause PCI based drivers to enable PM twice, once when the PCI device is added and a second time in m_can_class_register(). This will cause 'Unbalanced pm_runtime_enable!' to be logged, and is a situation that should be avoided. Therefore, in anticipation of PCI devices, move PM enabling out from M_CAN class registration to its only user, the m_can_platform driver. Signed-off-by:
Patrik Flykt <patrik.flykt@linux.intel.com> Link: https://lore.kernel.org/r/20201023115800.46538-2-patrik.flykt@linux.intel.com [mkl: m_can_plat_probe(): fix error handling m_can_class_register(): simplify error handling] Signed-off-by:
-
Sean Nyekjaer authored
The CSR bit is already cleared when arriving here so remove this section of duplicate code. The registers set in m_can_config_endisable() is set to same exact values as before this patch. Signed-off-by:
Sean Nyekjaer <sean@geanix.com> Acked-by:
Sriram Dash <sriram.dash@samsung.com> Acked-by:
Dan Murphy <dmurphy@ti.com> Link: https://lore.kernel.org/r/20191211063227.84259-1-sean@geanix.com Fixes: f524f829 ("can: m_can: Create a m_can platform framework") Signed-off-by:
-
Antonio Quartulli authored
The definition of IS_ERR() already applies the unlikely() notation when checking the error status of the passed pointer. For this reason there is no need to have the same notation outside of IS_ERR() itself. Clean up code by removing redundant notation. Signed-off-by:
-
Oliver Hartkopp authored
When CAN_ISOTP_SF_BROADCAST is set in the CAN_ISOTP_OPTS flags the CAN_ISOTP socket is switched into functional addressing mode, where only single frame (SF) protocol data units can be send on the specified CAN interface and the given tp.tx_id after bind(). In opposite to normal and extended addressing this socket does not register a CAN-ID for reception which would be needed for a 1-to-1 ISOTP connection with a segmented bi-directional data transfer. Sending SFs on this socket is therefore a TX-only 'broadcast' operation. Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Thomas Wagner <thwa1@web.de> Link: https://lore.kernel.org/r/20201206144731.4609-1-socketcan@hartkopp.netSigned-off-by:
-
David S. Miller authored
Huazhong Tan says: ==================== net: hns3: updates for -next This patchset adds support for tc mqprio offload, hw tc offload of tc flower, and adpation for max rss size changes. ==================== Signed-off-by: -
Guojia Liao authored
For the max rss size of PF may be up to 512, the max queue number of single tc may be up to 512 too. For the total queue numbers may be up to 1280, so the queue offset of each tc may be more than 1024. So adjust the rss tc mode configuration command, including extend tc size field from 10 bits to 11 bits, and extend tc size field from 3 bits to 4 bits. Signed-off-by:
Guojia Liao <liaoguojia@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
Guojia Liao authored
For the max rss size of PF may be up to 512, so adjust the command of configuring rss indirection table to support queue id larger than 255. The width of queue id is extended from 8 bits to 10 bits. The high 2 bits are stored in filed rss_qid_h when the queue id is larger than 255. Signed-off-by:
-
