- 18 Dec, 2018 25 commits
-
-
Chen-Yu Tsai authored
The BCM20702A1 is a Bluetooth 4.0 chip from Broadcom. It is found in the Ampak AP6210 WiFi+BT module, identified from the read verbose config info command response. However the Bluetooth firmware provided by vendors uses the name BCM20710. This patch elects to use the chip ID returned by the chip for the compatible string. Reviewed-by:
Rob Herring <robh@kernel.org> Tested-by:
Ondrej Jirman <megous@megous.com> Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org>
-
Chen-Yu Tsai authored
The Broadcom Bluetooth chips have two power inputs, VBAT and VDDIO. The former provides overall power for the chip, while the latter powers the I/O pins and buffers. This patch adds properties for the two so we can describe the power supply relationships. Reviewed-by:
-
Chen-Yu Tsai authored
The Broadcom Bluetooth controllers can take up to two external clocks: an external frequency reference, substituting the main crystal, and a LPO clock at 32.768 kHz substituting the internal LPO clock. In particular, the external LPO clock must be used when the controller does not have NVRAM connected, and the main reference frequency is not the default 20 MHz. This is described in detail in the datasheet. The original "extclk" clock name is ambiguous as to which of these it refers to, and some designs might even require both. This patch deprecates the existing name, and adds "txco" and "lpo". Tested-by:
-
Yangtao Li authored
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code. Signed-off-by:
Yangtao Li <tiny.windzz@gmail.com> Reviewed-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Yangtao Li authored
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code. Signed-off-by:
-
John Hurley authored
Previously the identifier used for indirect block callback registry and for block rule cb registry (when done via indirect blocks) was the pointer to the netdev we were interested in receiving updates on. This worked fine if a single app existed that registered one callback per netdev of interest. However, if multiple cards are in place and, in turn, multiple apps, then each app may register the same callback with the same identifier to both the netdev's indirect block cb list and to a block's cb list. This can lead to EEXIST errors and/or incorrect cb deletions. Prevent this conflict by using the app pointer as the identifier for netdev indirect block cb registry, allowing each app to register a unique callback per netdev. For block cb registry, the same app may register multiple cbs to the same block if using TC shared blocks. Instead of the app, use the pointer to the allocated cb_priv data as the identifier here. This means that there can be a unique block callback for each app/netdev combo. Fixes: 3166dd07 ("nfp: flower: offload tunnel decap rules via indirect TC blocks") Reported-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
John Hurley <john.hurley@netronome.com> Reviewed-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Shalom Toledo authored
This new firmware contains: * New packet traps for discarded packets * Secure firmware flash bug fix * Fence mechanism bug fix * TCAM RMA bug fix Signed-off-by:
Shalom Toledo <shalomt@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
David Ahern authored
mfc6_cache is not needed by ip6mr_forward2 so drop it from the input argument list. Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
David Ahern authored
mfc_cache is not needed by ipmr_queue_xmit so drop it from the input argument list. Signed-off-by:
-
Peter Oskolkov authored
Commit d9fbc7f6 "net: tcp: prefer listeners bound to an address" removes port-only listener lookups. This caused segfaults in DCCP lookups because DCCP did not initialize the (addr,port) hashtable. This patch adds said initialization. The only non-trivial issue here is the size of the new hashtable. It seemed reasonable to make it match the size of the port-only hashtable (= INET_LHTABLE_SIZE) that was used previously. Other parameters to inet_hashinfo2_init() match those used in TCP. V2 changes: marked inet_hashinfo2_init as an exported symbol so that DCCP compiles when configured as a module. Tested: syzcaller issues fixed; the second patch in the patchset tests that DCCP lookups work correctly. Fixes: d9fbc7f6 "net: tcp: prefer listeners bound to an address" Reported-by:
syzcaller <syzkaller@googlegroups.com> Signed-off-by:
Peter Oskolkov <posk@google.com> Signed-off-by:
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Updates for net-next. Two main changes in this seris plus some miscellaneous changes. 1. Improvements and fixes for resource accounting which are required for enabling SR-IOV and RDMA on the new 57500 chips. Only SR-IOV for 57500 chips is enabled in this series. 2. New statistics counters and improvements to keep the basic counters and port counters during IFDOWN. 3. Msic. small changes for ETS, returning proper error codes when flashing NVRAM, and a link speed related fix for ethtool loopback selftest. ==================== Signed-off-by: -
Vasundhara Volam authored
With autoneg enabled, PHY loopback test fails. To disable autoneg, driver needs to send a valid forced speed to FW. FW is not sending async event for invalid speeds. To fix this, query forced speeds and send the correct speed when disabling autoneg mode. Signed-off-by:
Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Michael Chan authored
Port statistics which include RDMA counters are useful even when the netdevice is down. Do not free the port statistics DMA buffers when the netdevice is down. This is keep the snapshot of the port statistics and counters will just continue counting when the netdevice goes back up. Split the bnxt_free_stats() function into 2 functions. The port statistics buffers will only be freed when the netdevice is removed. Signed-off-by:
-
Michael Chan authored
With the current driver, the statistics reported by .ndo_get_stats64() are reset when the device goes down. Store a snapshot of the rtnl_link_stats64 before shutdown. This snapshot is added to the current counters in .ndo_get_stats64() so that the counters will not get reset when the device is down. Signed-off-by:
-
Vasundhara Volam authored
Currently firmware specific errors are returned directly in flash_device and reset ethtool hooks. Modify it to return linux standard errors to userspace when flashing operations fail. Signed-off-by:
-
Michael Chan authored
Currently, the code allows ETS bandwidth weight 0 to be set on unused TCs. We should not set any DCB parameters on unused TCs at all. Signed-off-by:
-
Michael Chan authored
Display the CoS counters as additional priority counters by looking up the priority to CoS queue mapping. If the TX extended port statistics block size returned by firmware is big enough to cover the CoS counters, then we will display the new priority counters. We call firmware to get the up-to-date pri2cos mapping to convert the CoS counters to priority counters. Signed-off-by:
-
Michael Chan authored
There are some minor differences when assigning VF resources on the new chips. The MSIX (NQ) resource has to be assigned and ring group is not needed on the new chips. Signed-off-by:
-
Michael Chan authored
When bringing up a device, the code checks to see if the number of MSIX has changed. pci_disable_msix() should be called first before changing the number of reserved NQs/CMPL rings. This ensures that the MSIX vectors associated with the NQs/CMPL rings are still properly mapped when pci_disable_msix() masks the vectors. This patch will prevent errors when RDMA support is added for the new 57500 chips. When the RDMA driver shuts down, the number of NQs is decreased and we must use the new sequence to prevent MSIX errors. Signed-off-by:
-
Vasundhara Volam authored
bnxt_en requires same number of stat_ctxs as CP rings but RDMA requires only 1 stat_ctx. Also add a new parameter resv_stat_ctxs to better keep track of stat_ctxs reserved including resources used by RDMA. Add a stat_ctxs parameter to all the relevant resource reservation functions so we can reserve the correct number of stat_ctxs. Prior to this patch, we were not reserving the extra stat_ctx for RDMA and RDMA would not work on the new 57500 chips. Signed-off-by:
-
Vasundhara Volam authored
Calling bnxt_set_max_func_stat_ctxs() to modify max stat_ctxs requested or freed by the RDMA driver is wrong. After introducing reservation of resources recently, the driver has to keep track of all stat_ctxs including the ones used by the RDMA driver. This will provide a better foundation for accurate accounting of the stat_ctxs. Signed-off-by:
-
Vasundhara Volam authored
For bnxt_en driver, stat_ctxs created will always be same as cp_nr_rings. Remove extra variable that duplicates the value. Also introduce bnxt_get_avail_stat_ctxs_for_en() helper to get available stat_ctxs and bnxt_get_ulp_stat_ctxs() helper to return number of stat_ctxs used by RDMA. Signed-off-by:
-
Michael Chan authored
The available CP rings are calculated differently on the new 57500 chips, so add this helper to do this calculation correctly. The VFs will be assigned these available CP rings. Signed-off-by:
-
Michael Chan authored
The PF has a pool of NQs and MSIX vectors assigned to it based on NVRAM configurations. The number of usable MSIX vectors on the PF is the minimum of the NQs and MSIX vectors. Any excess NQs without associated MSIX may be used for the VFs, so we need to store this max_nqs value. max_nqs minus the NQs used by the PF will be the available NQs for the VFs. Signed-off-by:
-
Stefano Brivio authored
Handling exceptions for direct UDP encapsulation in GUE (that is, UDP-in-UDP) leads to unbounded recursion in the GUE exception handler, syzbot reported. While draft-ietf-intarea-gue-06 doesn't explicitly forbid direct encapsulation of UDP in GUE, it probably doesn't make sense to set up GUE this way, and it's currently not even possible to configure this. Skip exception handling if the GUE proto/ctype field is set to the UDP protocol number. Should we need to handle exceptions for UDP-in-GUE one day, we might need to either explicitly set a bound for recursion, or implement a special iterative handling for these cases. Reported-and-tested-by: syzbot+43f6755d1c2e62743468@syzkaller.appspotmail.com Fixes: b8a51b38 ("fou, fou6: ICMP error handlers for FoU and GUE") Signed-off-by:
Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
-
- 17 Dec, 2018 6 commits
-
-
Joakim Tjernlund authored
This allows to control carrier from /sys/class/net/ethX/carrier for Fixed PHYs. Signed-off-by:
Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by:
-
Joakim Tjernlund authored
This allows to control carrier from /sys/class/net/ethX/carrier for Fixed PHYs. Signed-off-by:
-
Joakim Tjernlund authored
This allows to control carrier from /sys/class/net/ethX/carrier for Fixed PHYs. Signed-off-by:
-
Joakim Tjernlund authored
Drivers can use this as .ndo_change_carrier() to change carrier via /sys/class/net/ethX/carrier. Signed-off-by:
-
Eric Dumazet authored
kzalloc_node(..., GFP_KERNEL, node) will attempt to allocate memory as close as possible to the node. There is no need to fallback to kzalloc() if this has failed. Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Paolo Abeni authored
The kbuild bot reported a build breakage with CONFIG_RETPOLINE=n due to commit aaa5d90b ("net: use indirect call wrappers at GRO network layer"). I screwed the wrapper implementation for such config. Fix the issue properly ignoring the builtin symbols arguments, when retpoline is not enabled. Reported-by:
kbuild test robot <lkp@intel.com> Fixes: aaa5d90b ("net: use indirect call wrappers at GRO network layer") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
- 16 Dec, 2018 9 commits
-
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw: spectrum_acl: Add Bloom filter support Nir says: Spectrum-2 uses Bloom filter to reduce the number of lookups in the algorithmic TCAM (A-TCAM). HW performs multiple exact match lookups in a given region using a key composed of { packet & mask, mask ID, region ID }. The masks which are used in a region are called rule patterns or RP. When such multiple masks are used, the A-TCAM region uses an eRP (extended RP) table that describes which rule patterns are in use and defines the order of the lookup. When eRP table is used in a region, one way to reduce the number of the lookups is to consult a Bloom filter before doing the lookup. A Bloom filter is a space-efficient probabilistic data structure, on which a query returns either "possibly in set" or "definitely not in set". HW can skip a lookup if a query on the Bloom filter results a "definitely not set" response. The mlxsw driver implements a "counting filter" and when either a new entry is marked or the last entry is removed it will update the HW. Update of this counting filter occurs when rule is configured or deleted from a region. Patch #1 adds PEABFE register which is used for setting Bloom filter entries. Patch #2 adds Bloom filter resources. Patch #3 and patch #4 provide Bloom filter handling within mlxsw, by adding initialization and logic for updating the Bloom bit vector in HW. Patch #5 and patch #6 add required calls for Bloom filter update as part of rule configuration flow. Patch #7 handles transitions to and from eRP table. It uses a list to keep A-TCAM rules in order to update rules in Bloom filter, in cases of transitions from master mask based A-TCAM region to an eRP table based region and vice versa. Patch #8 removes a trick done on master RP index to a remaining RP, since Bloom filter is updated on eRP transitions. Finally, patch #9 activates Bloom filter mechanism in HW, by cancelling the bypass that was configured before and the remaining three patches are selftests that exercise the new code. ==================== Signed-off-by: -
Nir Dotan authored
The eRP table is active when there is more than a single rule pattern. It may be that the patterns are close enough and use delta mechanism. Bloom filter index computation is based on the values of {rule & mask, mask ID, region ID} where the rule delta bits must be cleared. Add a test that exercises Bloom filter with delta mechanism. Configure rules within delta range and pass a packet which is supposed to hit the correct rule. Signed-off-by:Nir Dotan <nird@mellanox.com> Signed-off-by:
-
Nir Dotan authored
Bloom filter index computation is based on the values of {rule & mask, mask ID, region ID} and the computation also varies according to the region key size. Add a test that exercises the possible combinations by creating multiple chains using different key sizes and then pass a frame that is supposed to to produce a hit on all of the regions. Signed-off-by: -
Nir Dotan authored
Add a test that exercises Bloom filter code. Activate eRP table in the region by adding multiple rule patterns which with very high probability use different entries in the Bloom filter. Then send packets in order to check lookup hits on all relevant rules. Signed-off-by:
-
Nir Dotan authored
Now that mlxsw driver handles all aspects of updating the Bloom filter mechanism, set bf_bypass value to false and allow HW to use Bloom filter. Signed-off-by:
-
Nir Dotan authored
Bloom filter is updated on transitions from a single rule pattern, also called master RP, to eRP table and vice versa. Since rules are being written to or deleted from the Bloom filter on such transitions, it is not required to keep the same eRP bank ID for the master RP. Change master RP index assignment so it will be assigned with zero. This is consistent with the assignment of the first available spot that is used for allocating eRP's indices. Signed-off-by:
-
Nir Dotan authored
Bloom filter update is required only for rules which reside on an eRP. When the region has only a single rule pattern then eRP table is not used, however insertion of another pattern would trigger a move to an active eRP table so it is imperative to update the Bloom filter with all previously configured rules. Add a method that updates Bloom filter entries for all rules currently configured in the region, on the event of a transition from master mask to eRP, or vice versa. For that purpose, maintain a list of all A-TCAM rules within mlxsw_sp_acl_atcam_region. Signed-off-by:
-
Nir Dotan authored
Add calls to eRP module for updating Bloom filter when a rule is added or removed from the A-TCAM. eRP module will update the Bloom filter only for cases in which the region has an active eRP table. Signed-off-by:
-
Nir Dotan authored
Add Bloom filter update for rule insertion and rule removal scenarios. This is done within eRP module in order to assure that Bloom filter updates are done only for rules which are part of an eRP, as HW does not consult Bloom filter for entries when there is a single (master) mask in the region. Signed-off-by:
-
