Remove the following sparse warnings by declaring attr as static:
arch/arm/mach-omap2/serial.c:627:1: warning: symbol 'dev_attr_sleep_timeout'
was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Initialization of pointer should be done with NULL. Removes sparse
warnings:
arch/arm/mach-omap2/serial.c:566:17: warning: Using plain integer as NULL pointer
arch/arm/mach-omap2/serial.c:567:17: warning: Using plain integer as NULL pointer
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Adds context save/restore for mcr register as state of mcr register
is lost after core off.
Signed-off-by: Govindraj R <govindraj.raja@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add initial support for the OMAP4 based Panda Board.
Signed-off-by: David Anders <x0132446@ti.com>
[tony@atomide.com: selected board by default in Kconfig]
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds support for GPIO LEDs present on OMAP4
SDP and Blaze boards. This basically adds platform data
required by leds-gpio driver
Signed-off-by: Hemanth V <hemanthv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Adding board configuration for the tmp105
temperature sensor. The interface to the sensor
is I2C.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The MMC1 and MMC2 cards have seperate LDO supplies. Current code assumes
that they are powered by same LDO.

This patch fixes the same and has VAUX1 as supply to MMC2 card.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This commit will enable usage of tsl2563 ambient light sensor on Nokia N900.
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With these and upcoming change to tpa6130a2 driver it's possible to add
support for the TPA6130A2 headphone amplifier.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

There is REGULATOR_SUPPLY macro available for initializing the struct
regulator_consumer_supply so use it where applicable (all other supplies
than vdds_sdi) as it improves the readability.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Proper operation of the tlv320aic3x audio codec requires that reset
sequencing is done in pair with supply voltages when using the regulator
framework. Add the codec reset gpio used in Nokia RX51 to tlv320aic3x
data.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

It seems that the battery cover sensor in Nokia N900 is powered from the
V28 domain. Now if this regulator is disabled it causes that the gpio 160
reads only zero which effectively causes uSD removal detection.

Currently the bootloader enabled V28 is kept on but this may change in the
future according to comment in
drivers/regulator/core.c: regulator_has_full_constraints.

Also if there are any consumers on the V28 domain doing regulator_enable
regulator_disable cycle the V28 will be disabled after that.

Prepare for these by defining the V28 as always_on regulator.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add platform data for NAND and wifi, also setup all GPIOs
needed to use the wifi chip.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Update gpio-keys setup so it matches what is on default firmware.
Also make use of debounce feature in gpio-keys instead of setting it
explicitly, as gpio-keys is now capable of using hardware debounce on
OMAPs thanks to recent gpiolib changes.
Also fix a sparce warning along the way.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM3.
Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM2.
Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Devkit8000 uses the TPS65930 and not the TWL4030.
The TPS65930 uses only a subset of the power supplies
of the TWL4030.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap_board_config is no longer used and thats why empty.
This patch removes the empty omap_board_config.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Using the macro gpio_is_valid for check of valid gpio pins.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Replacing supplies with the REGULATOR_SUPPLY macro.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

devkit8000_panel_enable_tv and devkit8000_panel_disable_tv are already
done in DSS2 code. So they are no longer needed in board code.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The Devkit8000 uses the cost reduced variant tps65930 of the twl4030.
The TPS65930 only has vdd1, vdd2, vpll1, vio, vmmc1, vdac and vaux2.

vaux2 is not used on Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The VDVI power supply is no longer needed in
board code with the new DSS2 interface.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch corrects the LCD reset pin configuration.

Original code from early devkit8000 patch sets the TWL4030 GPIO_1
to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins
are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be
disabled when other display is turned on.
Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch corrects the DVI-D output setup of Devkit8000

Devkit8000 has different DVI reset pin with the BeagleBoard.
On Devkit8000 the TWL4030 GPIO_7 is assigned to do the job.
Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Choose the generic panel for lcd code of Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Corrected the wrong power supplies in devkit8000 code.

Add supply for ads7846 to support the new regulator framework for
touchscreen.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

MACH_OMAP2_H4_USB1 doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

MACH_OMAP_H4_OTG doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

APM doesn't exist in Kconfig, therefore removing all references for it
from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

LEDS_OMAP_DEBUG doesn't exist in Kconfig, therefore replacing all
references for it with OMAP_DEBUG_LEDS from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP_STI doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP_DSP doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated to apply on top of already queued patches]
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP_IR doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated for new mux code]
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP_MUX_ERRORS doesn't exist in Kconfig, therefore replacing all
references for it with OMAP_MUX_WARNINGS in the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This produces a sane config that's suitable for using as the
base for most omap2/3/4 boards.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Select all omaps and boards by default
Signed-off-by: Tony Lindgren <tony@atomide.com>

Move omap2/3/4 specific Kconfig options to mach-omap2/Kconfig
Signed-off-by: Tony Lindgren <tony@atomide.com>

This will make Kconfig look nicer for selecting omap processor type
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use 32KiHZ timer by default as this is available on all omaps
except 15xx based systems.
Signed-off-by: Tony Lindgren <tony@atomide.com>