No functional changes.

Adjust to comply with dt-schema requirements
and make possible to validate values.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Toradex Verdin IMX8MP Mallow carrier board support. Mallow is a
low-cost carrier board in the Verdin family with a small form factor and
build for volume production making it ideal for industrial and embedded
applications.

https://www.toradex.com/products/carrier-board/mallow-carrier-boardSigned-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Toradex Verdin IMX8MM Mallow carrier board support. Mallow is a
low-cost carrier board in the Verdin family with a small form factor and
build for volume production making it ideal for industrial and embedded
applications.

https://www.toradex.com/products/carrier-board/mallow-carrier-boardSigned-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As per Rob Herring's feedback:

"The ethernet device should have a node name of
'ethernet'. The 'pcie' node name and 'device_type = "pci"' is for PCI
buses/bridges only."

Do it as suggested.

Fixes: d61c5068729a ("arm64: dts: imx8mm-venice-gw7: Fix pci sub-nodes")
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since commit 8208181f ("clk: imx: composite-8m:
Add imx8m_divider_determine_rate") the lcdif controller has
had the ability to set the lcdif_pixel rate which propagates
up the tree and sets the video_pll1 rate automatically.

By setting this value low, it will force the recalculation of
video_pll1 to the lowest rate needed by lcdif instead of
dividing a larger clock down to the desired clock speed. This
has the  advantage of being able to lower the video_pll1 rate
from 594MHz to 148.5MHz when operating at 1080p. It can go even
lower when operating at lower resolutions and refresh rates.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> # Kontron BL i.MX8MM
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There are two clock-rate assignments for video_pll1, and the
only one it should really have belongs inside the lcdif node,
since it's the only consumer of this clock.  Remove it from
the clk node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> # Kontron BL i.MX8MM
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The device tree clock structure for the mipi_dsi is
unnecessarily redundant.

The default clock parent of IMX8MM_CLK_DSI_PHY_REF is
already IMX8MM_CLK_24M, so there is no need to set the
parent-child relationship between them.  The default clock
rates for IMX8MM_SYS_PLL1_266M and IMX8MM_CLK_24M are
already defined to be 266MHz and 24MHz respectively,
so there is no need to define those clock rates.

On i.MX8M[MNP] the  samsung,pll-clock-frequency is not
necessary, because the driver will read it from sclk_mipi
which is also already set to 24MHz making it also
redundant.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> # Kontron BL i.MX8MM
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The DTS code coding style expects exactly one space before and after '='
sign.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX8DXL's ddr pmu has port/channel filter capabilities, but it still is
compatible with "fsl,imx8-ddr-pmu". This will change the compatible.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

'dr_mode' is part of the USB DWC3 core, not the glue layer. Remove the
property from glue layer. Fixes the dtbs_check warning:
arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dtb: usb@32f10108:
  'dr_mode' does not match any of the regexes: '^usb@[0-9a-f]+$',
  'pinctrl-[0-9]+'
 from schema $id: http://devicetree.org/schemas/usb/fsl,imx8mp-dwc3.yaml#Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 'shared-interrupt' property is not documented nor used anywhere.

Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 'shared-interrupt' property is not documented nor used anywhere.

Remove it.

This fixes the following schema warning:

imx93-11x11-evk.dtb: dma-controller@42000000: Unevaluated properties are not allowed ('shared-interrupt' was unexpected)
	from schema $id: http://devicetree.org/schemas/dma/fsl,edma.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per gpio-sbu-mux.yaml, the compatible entry is incomplete.

The imx8qxp-mek board uses a CBDTU02043, so complete the gpio-sbu-mux
compatible accordingly.

This fixes the following schema warning:

imx8qxp-mek.dtb: gpio-sbu-mux: compatible:0: 'gpio-sbu-mux' is not one of ['onnn,fsusb43l10x', 'pericom,pi3usb102']
	from schema $id: http://devicetree.org/schemas/usb/gpio-sbu-mux.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The property 'phy-connection-type' can be used to describe the interface
type between the Ethernet device and the Ethernet PHY device.

However, snps,dwmac.yaml gives the following warning:

imx8mp-debix-model-a.dtb: ethernet@30bf0000: 'phy-mode' is a required property
	from schema $id: http://devicetree.org/schemas/net/snps,dwmac.yaml#

To avoid the warning, switch to the more commonly used, 'phy-mode'
property instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per i2c-mux-pca954x.yaml, the I2C subnodes should follow the
'i2c@' format.

Change it to fix the following schema warning:

imx8mm-nitrogen-r2.dtb: i2c-mux@70: Unevaluated properties are not allowed ('i2c3@0' was unexpected)
	from schema $id: http://devicetree.org/schemas/i2c/i2c-mux-pca954x.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per snps,dwmac.yaml, the interrupt-names entries should be in the
following order: "macirq", "eth_wake_irq";

Change it to fix the following schema warnings.

imx8dxl-evk.dtb: ethernet@5b050000: interrupt-names:0: 'macirq' was expected
	from schema $id: http://devicetree.org/schemas/net/snps,dwmac.yaml#
imx8dxl-evk.dtb: ethernet@5b050000: interrupt-names:1: 'macirq' is not one of ['eth_wake_irq', 'eth_lpi']
	from schema $id: http://devicetree.org/schemas/net/snps,dwmac.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per nxp,pcf8575.yaml, #gpio-cells should be 2.

Change it to fix the following schema warning:

imx8mm-emcon-avari.dtb: gpio@3a: #gpio-cells:0:0: 2 was expected
	from schema $id: http://devicetree.org/schemas/gpio/nxp,pcf8575.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per fsl-lpuart.yaml, when the 'dmas' property is used 'dma-names' should
also be present.

Pass the lpuart 'dma-names' property to fix the following schema
warnings:

imx8dxl-evk.dtb: serial@5a060000: dma-names:0: 'rx' was expected
	from schema $id: http://devicetree.org/schemas/serial/fsl-lpuart.yaml#
imx8dxl-evk.dtb: serial@5a060000: dma-names:1: 'tx' was expected
	from schema $id: http://devicetree.org/schemas/serial/fsl-lpuart.yaml#
imx8dxl-evk.dtb: serial@5a060000: Unevaluated properties are not allowed ('dma-names' was unexpected)
	from schema $id: http://devicetree.org/schemas/serial/fsl-lpuart.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Skov i.MX8MP based climate controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following warning is shown when probing device:

    pca953x 1-0020: supply vcc not found, using dummy regulator

Define a new fixed 3.3v regulator for carrier board peripherals,
enabled by mosfet switch Q2 after the SOM_3V3 supply rises (no software
control).

Add this new regulator as vcc supply to the PCA9534 to silence the warning.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The RVE gateway board is based on a Variscite VAR-SOM-NANO,
with a NXP MX8MN nano CPU.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Provide the 1.8 and 3.3 volt regulators that are utilised on the Debix
SOM BMB-08 base board.

Facilitate this by also supplying the pin control used to enable the
regulators on the second MIPI CSI port.
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Newer variants of Ixora boards require a power-up delay when powering up
the CAN transceiver of up to 1ms.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

When the EEPROM is probed, we have this warning:

    at24 0-0052: supply vcc not found, using dummy regulator

Add fixed 3.3v regulator to silence the warning.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Several schema warnings are seen when running:

make dtbs_check DT_SCHEMA_FILES=pci-bus.yaml

Fix them.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Even if the 'dsp' node is disabled the memory intended to be used by the
DSP is reserved. This limits the memory range suitable for CMA allocation.
Thus disable the dsp_reserved node. DSP users need to enable it in parallel
to the 'dsp' node.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The NPU is based on the Vivante GC8000 and its power-domain
is controlled my pgc_mlmix.  Since the power-domain uses
some of these clocks, setup the clock parent and rates
inside the power-domain, and add the NPU node.

The data sheet states the CLK_ML_AHB should be 300MHz for
nominal, but 800MHz clock will divide down to 266 instead.
Boards which operate in over-drive mode should update the
clocks on their boards accordingly.  When the driver loads,
the NPU numerates as:

 etnaviv-gpu 38500000.npu: model: GC8000, revision: 8002
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Map the 'RUN' LED present on the Debix-SOM as a heartbeat.
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds an overlay for the supported LVDS display AUO G133HAN01.
Configure the video PLL frequency to exactly match typical pixel clock of
141.200 MHz.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove unnecessary #address-cells and #size-cells from tpm node.

Fixes: 531936b2 ("arm64: dts: imx8mp-venice-gw74xx: update to revB PCB")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the TPM device found on the GW72xx revision F PCB.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the TPM device found on the GW72xx revision F PCB.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The anatop module produces PLL and OSC for Clock Controller Module. Since
the binding doc has been updated to clock-controller for this module,
Let's also update the device tree node.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

To support SD3.0 mode, according to the SD spec, a clean power off
for the VDD_SD is keep the VDD_SD lower than 0.5V for at least 1ms.
On imx93 board, gate off the VDD_SD, it will cost about 10ms to see
the voltage change from 3.3v to 0.5v. So at least need to dealy 11ms
to make sure a clean power off and power on. Here add 12ms dealy.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

For original setting, the start point is 20, after the SION setting,
ERR052021 can be workaround, but start point from 20 is too large,
especially for the LD 133MHz case.

Set the tuning start point as 1, tuning step as 2, so that, for the
40 times tuning logic, it can cover 1~81, its large and safe enough
for all different devices like eMMC/SD/SDIO.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx93 pad integrate has one issue, refer to ERR052021:

ERR052021 uSDHC: Sometimes uSDHC does not work under VDD_SOC low
		 drive mode and nominal mode
Description:
uSDHC PADs have one integration issue.
When CMD/DATA lines direction change from output to input, uSDHC
controller begin sampling, the integration issue will make input
enable signal from uSDHC propagated to the PAD with a long delay,
thus the new input value on the pad comes to uSDHC lately. The
uSDHC sampled the old input value and the sampling result is wrong.

Workaround:
Set uSDHC CMD/DATA PADs iomux register SION bit to 1, then PADs will
propagate input to uSDHC with no delay, so correct value is sampled.

This issue will wrongly trigger the start bit when sample the USDHC
command response, cause the USDHC trigger command CRC/index/endbit
error, which will finally impact the tuning pass window, espically
will impact the standard tuning logic, and can't find a correct delay
cell to get the best timing.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX8MP DHCOM SoM production rev.200 is populated with M24C32-D
EEPROMs which have Additional Write lockable page at separate I2C
address. Describe the page in DT to make it available.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The baseboard of the Beacon i.MX8M Plus development kit has
an ADV7535 DSI to HDMI bridge capable of stereo sound.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add both CCM interrupts as mentioned in RM.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add both CCM interrupts as mentioned in RM.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>