Enable the 2 ethernet ports as CPSW ports in dual-mac mode
Signed-off-by: Roger Quadros <rogerq@ti.com>
[nsekhar@ti.com: use AM33XX_IOPAD()]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM571x IDK and the AM572x IDK use CAN1 interface.
This patch enables it for both boards.

Tested on AM572x IDK using cansequence.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[nsekhar@ti.com: move to use DRA7XX_CORE_IOPAD())
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

All three devices provide GPIO based LEDs named power,
wlan and app.

Place LEDs definition into a separate dtsi file as not all
devices including am335x-baltos.dtsi have the same LED layout.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

There's a typo, it should be GPIO176 and not GPIO106.

And it seems I messed up the regulators at some point while trying
to figure out what devices the regulators are used. The correct
regulator for MMC1 is vwlan2.

Fixes: 0d4cb3cc ("ARM: dts: Configure regulators for droid 4")
Reported-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add cpu_thermal zone.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add pinmux for rx,tx,cts and rts lines of uart0. This will enable uart0
to use hardware flow control.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable support for W25Q64CVSSIG which is a Winbond 64 Mbit SPI NOR.

At boot you will see the following message:
m25p80 spi1.0: found s25fl064k, expected w25q64

This is because the JEDEC ID for this chip is the same as s25fl064k.
However, this should be harmless since both chips are essentially the
same.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

W25Q64 is found on TI's AM335x ICEv2 board. Add it to list
for supported SPI flash devices. This flash can be identified
using JEDEC READ ID opcode.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in dra7.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.

As we now need to define voltage ranges for each OPP, we define the
minimum and maximum voltage to match the ranges possible for AVS class0
voltage as defined by the DRA7/AM57 Data Manual, with the exception of
using a range for OPP_OD based on historical data to ensure that SoCs
from older lots still continue to boot, even though more optimal voltages
are now the standard. Once an AVS Class0 driver is in place it will be
possible for these OPP voltages to be adjusted to any voltage within the
provided range.

Information from SPRS953, Revised December 2015.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The operatings-points-v2 table for am4372 was merged before any user of
it was present in the kernel and before the binding had been finalized.
The new ti-cpufreq driver and binding expects the platform specific
properties to be part of the operating-points-v2 table rather than the
cpu node so let's move them there as the only user is the ti-cpufreq
driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Although all PG2.0 silicon may not support 1GHz OPP for the MPU, older
Beaglebone Blacks may have PG2.0 silicon populated and these particular
parts are guaranteed to support the OPP, so enable it for PG2.0 on
am335x-boneblack only.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in am33xx.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.

Information from AM335x Data Manual, SPRS717i, Revised December 2015,
Table 5-7.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the SATA controller node to the dm8168-evm device tree.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This board has an external oscillator supplying the reference clock
signal for SATA. Its rate is fixed at 100Mhz. Add a corresponding
device tree node.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The Nokia N950 and N9 have a wl1271 (with nokia bootloader) bluetooth
module connected to second UART.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add bcm2048 node and its system clock to the N900 device tree file.
Apart from that a reference to the new clock has been added to
wl1251 (which uses it, too).
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Droid 4 has two modems, mdm6600 and w3glte. Both are on the HCI USB
controller.

Let's add a configuration for the HCI so the modems can be enabled.

Note that the modems still need additional GPIO based configuration.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
[tony@atomide.com: left out url]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add LEDs.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The LCD panel on droid 4 is a command mode LCD. The binding follows
the standard omapdrm binding and the changes needed for omapdrm command
mode panels are posted separately.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can get HDMI working as long as the 5V regulator is on. There is
probably an encoder chip there too, but so far no idea what it might be.
Let's keep the 5V HDMI regulator always enabled for now as otherwise we
cannot detect the monitor properly.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add tmp105 sensor for droid 4. This can be used with modprobe
lm75.ko and running sensors from lm-sensors package. Note that
the lm75.c driver does not yet support alert interrupt but
droid 4 seems to be wired for it.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Droid 4 has a GPIO line that we can use with CONFIG_POWER_RESET_GPIO.
It is probably connected to the CPCAP PMIC, and seems to power down
the whole device taking power consumption to zero based on what
I measured.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The TI LMU driver has not yet been merged, but the device
tree binding for TI LMU drivers has been acked already
earlier by Rob Herring <robh+dt@kernel.org>. So it should
be safe to apply to cut down the number of pending patches.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add OneNAND node for IGEP and leave it disabled by default. It is up
to bootloader to enable proper node. Timing just works, but values are
copied over from N900 as I was unable to find chip datasheet.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

HECC node description for am35x SOCs
Signed-off-by: Anton Glukhov <anton.a.glukhov@gmail.com>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Droid4's touchscreen can be used with mainline's maxtouch driver. The
touchscreen's lower area is used for four soft buttons (KEY_MENU,
KEY_HOME, KEY_BACK, KEY_SEARCH), but that does not seem to be currently
supported by the mainline kernel.

The mxt224 configuration can be saved with "mxt-app" for the kernel
to load. It can be saved after the first boot with:

# mxt-app -d i2c-dev:1-004a --save /lib/firmware/maxtouch.cfg

Where the mxt-app can be found at:

https://github.com/atmel-maxtouch/mxt-app

The firmware for the droid 4 mxt224 comes with GPLv2 license in the
Motorola Linux kernel sources. This firmware can be dumped out with
"droid4-touchscreen-firmware" program at:

https://github.com/tmlind/droid4-touchscreen-firmware

The related LCD patches are still pending, but when merged,
the touchscreen can be rotated in X with something like:

# xrandr --output DSI-1 --rotate right
# xinput set-prop 6 'Coordinate Transformation Matrix' \
	0 1 0 -1 0 1 0 0 1

For now, we rely on a gpio-hog but later on we can add the reset
gpio handling to the driver and have it load the maxtouch.cfg and
maxtouch.fw on boot.

This patch is based on combined similar patches done by me and
Sebastian.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add accelerometer.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add compass.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add power button.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add rtc.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On Droid 4 "Volume Down" and "Keypad Slide" keys are
connected via SoC GPIOs, "Power Key" via CPCAP and
all other keys via SoC keypad Matrix. This adds the
GPIO keys.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
[tony@atomide.com: updated to apply on omap4-keypad patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>

With drivers/mfd/motorola-cpcap.c and drivers/regulator/cpcap-regulator.c
we can now configure proper regulators for droid 4.

Let's add regulator voltages and switch over MMC, eMMC and WLAN to use
the CPCAP regulators.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Let's configure the keypad in a way where it's usable out of the
box for Linux console use. We want to have the keyboard usable with
Linux console for example when stuck into an initramfs during boot,
for when installing a distro.

As we need to need to have keys mapped in the user space anyways
for some of the keys to match the labels, this non-standard mapping
or usability should be OK.

Some keys don't match the labels either as they don't follow the PC
keyboard style. For example we have "shift + ," produce "<", and
"shift + ." produce ">" instead of ";" and ":".

So let's follow the standard PC keyboard layout for ctrl, shift and
alt keys:

Ctrl = what is labeled as shift
Alt = what is labeled as SYM
Shift = what is lableled as caps lock

This way we have Ctrl key for console use. Who knows where they got
the caps lock idea.. Probably from some focus group popularity vote
or something.

For the OK key, let's keep it as the useless KEY_OK unless we can
come up with some standard mapping for it we can stick with.

We have at least Esc, Delete, Meta, and Page Down keys missing, but
none of them seem to be better than others. PC keyboard often has
Page Down in that location. Esc would be probably the most usable
one when installing a Linux distro but is the opposite of OK.

Note that the LCD keys are just touchscreen hot spots, so I'm not
sure if the driver or hardware allows setting them up as keys for
the console.

Anyways, the rest can be mapped in the user space.

Cc: Marcel Partap <mpartap@gmx.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull networking fixes from David Miller:

 1) Fix double-free in batman-adv, from Sven Eckelmann.

 2) Fix packet stats for fast-RX path, from Joannes Berg.

 3) Netfilter's ip_route_me_harder() doesn't handle request sockets
    properly, fix from Florian Westphal.

 4) Fix sendmsg deadlock in rxrpc, from David Howells.

 5) Add missing RCU locking to transport hashtable scan, from Xin Long.

 6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.

 7) Fix race in NAPI handling between poll handlers and busy polling,
    from Eric Dumazet.

 8) TX path in vxlan and geneve need proper RCU locking, from Jakub
    Kicinski.

 9) SYN processing in DCCP and TCP need to disable BH, from Eric
    Dumazet.

10) Properly handle net_enable_timestamp() being invoked from IRQ
    context, also from Eric Dumazet.

11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.

12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
    Melo.

13) Fix use-after-free in netvsc driver, from Dexuan Cui.

14) Fix max MTU setting in bonding driver, from WANG Cong.

15) xen-netback hash table can be allocated from softirq context, so use
    GFP_ATOMIC. From Anoob Soman.

16) Fix MAC address change bug in bgmac driver, from Hari Vyas.

17) strparser needs to destroy strp_wq on module exit, from WANG Cong.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
  strparser: destroy workqueue on module exit
  sfc: fix IPID endianness in TSOv2
  sfc: avoid max() in array size
  rds: remove unnecessary returned value check
  rxrpc: Fix potential NULL-pointer exception
  nfp: correct DMA direction in XDP DMA sync
  nfp: don't tell FW about the reserved buffer space
  net: ethernet: bgmac: mac address change bug
  net: ethernet: bgmac: init sequence bug
  xen-netback: don't vfree() queues under spinlock
  xen-netback: keep a local pointer for vif in backend_disconnect()
  netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
  netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
  netfilter: nf_conntrack_sip: fix wrong memory initialisation
  can: flexcan: fix typo in comment
  can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
  can: gs_usb: fix coding style
  can: gs_usb: Don't use stack memory for USB transfers
  ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
  ixgbe: update the rss key on h/w, when ethtool ask for it
  ...