- 04 Dec, 2017 3 commits
-
-
Geert Uytterhoeven authored
Commits 7d29f509 ("dt-bindings: i2c: i2c-gpio: Add support for named gpios") and 05c74778 ("i2c: gpio: Add support for named gpios in DT") introduced named i2c-gpio DT bindings, and deprecated the more error-prone unnamed variant. Switch to the new bindings, and add the missing GPIO_OPEN_DRAIN I/O flags, which were implicitly assumed before. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
Simon Horman <horms+renesas@verge.net.au>
-
Geert Uytterhoeven authored
Commits 7d29f509 ("dt-bindings: i2c: i2c-gpio: Add support for named gpios") and 05c74778 ("i2c: gpio: Add support for named gpios in DT") introduced named i2c-gpio DT bindings, and deprecated the more error-prone unnamed variant. Switch to the new bindings, and add the missing GPIO_OPEN_DRAIN I/O flags, which were implicitly assumed before. Signed-off-by:
-
Geert Uytterhoeven authored
Commits 7d29f509 ("dt-bindings: i2c: i2c-gpio: Add support for named gpios") and 05c74778 ("i2c: gpio: Add support for named gpios in DT") introduced named i2c-gpio DT bindings, and deprecated the more error-prone unnamed variant. Switch to the new bindings, and add the missing GPIO_OPEN_DRAIN I/O flags, which were implicitly assumed before. The latter gets rid of the message: gpio-208 (?): enforced open drain please flag it properly in DT/ACPI DSDT/board file gpio-91 (?): enforced open drain please flag it properly in DT/ACPI DSDT/board file Signed-off-by:
-
- 29 Nov, 2017 13 commits
-
-
Magnus Damm authored
Update the DTS to remove the now deprecated "renesas,channels-mask" property. The channel information is now kept in the device driver and can easily be determined based on the compat string. Signed-off-by:
Magnus Damm <damm+renesas@opensource.se> Signed-off-by:
-
Magnus Damm authored
Update the DTS to remove the now deprecated "renesas,channels-mask" property. The channel information is now kept in the device driver and can easily be determined based on the compat string. Signed-off-by:
-
Magnus Damm authored
Update the DTS to remove the now deprecated "renesas,channels-mask" property. The channel information is now kept in the device driver and can easily be determined based on the compat string. Signed-off-by:
-
Magnus Damm authored
Update the DTS to remove the now deprecated "renesas,channels-mask" property. The channel information is now kept in the device driver and can easily be determined based on the compat string. Signed-off-by:
-
Magnus Damm authored
Update the DTS to remove the now deprecated "renesas,channels-mask" property. The channel information is now kept in the device driver and can easily be determined based on the compat string. Signed-off-by:
-
Magnus Damm authored
Update the DTS to remove the now deprecated "renesas,channels-mask" property. The channel information is now kept in the device driver and can easily be determined based on the compat string. Signed-off-by:
-
Magnus Damm authored
Update the DTS to remove the now deprecated "renesas,channels-mask" property. The channel information is now kept in the device driver and can easily be determined based on the compat string. Signed-off-by:
-
Magnus Damm authored
Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings. With this change in place we can keep device-specific configuration in the driver and the driver can be able to support CMT1 specific features. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Magnus Damm authored
Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings. With this change in place we can keep device-specific configuration in the driver and the driver can be able to support CMT1 specific features. Signed-off-by:
-
Magnus Damm authored
Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings. With this change in place we can keep device-specific configuration in the driver and the driver can be able to support CMT1 specific features. Signed-off-by:
-
Magnus Damm authored
Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings. With this change in place we can keep device-specific configuration in the driver and the driver can be able to support CMT1 specific features. Signed-off-by:
-
Magnus Damm authored
Use the recently updated r8a73a4 CMT1 compat string. With this change in place we can keep device-specific configuration in the driver and the driver can be able to support CMT1 specific features. Signed-off-by:
-
Sergei Shtylyov authored
Add the device tree node for the Advanced Power Management Unit (APMU). Use the "enable-method" prop to point out that the APMU should be used for the SMP support. Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
- 27 Nov, 2017 24 commits
-
-
Geert Uytterhoeven authored
The Renesas part number of the two-wire serial interface EEPROM is not 24C128, but R1EX24128ASA00A. Hence change its primary compatible value to "renesas,r1ex24128". Signed-off-by:
-
Geert Uytterhoeven authored
The Renesas part number of the two-wire serial interface EEPROM is not 24C02, but R1EX24002ATAS0G. Hence change its primary compatible value to "renesas,r1ex24002", like on Gose. Signed-off-by:
-
Fabrizio Castro authored
Add VIN[01] support to SoC dt. Also, add aliases. Signed-off-by:
Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by:
Biju Das <biju.das@bp.renesas.com> Signed-off-by:
-
Fabrizio Castro authored
Add VIN[012] support to SoC dt. Also, add aliases. Signed-off-by:
-
Biju Das authored
Enable PCIe Controller & set PCIe bus clock frequency. Signed-off-by:
-
Biju Das authored
Signed-off-by:
-
Biju Das authored
This patch adds a default PCIe bus clock node. Signed-off-by:
-
Fabrizio Castro authored
CAN1 interface is exposed via connector J3 found on the camera daughter board. This patch enables can1 DT node from within the daughter board specific dtsi. Signed-off-by:
-
Fabrizio Castro authored
This patch enables CAN0 interface exposed through connector J20 on the carrier board. Signed-off-by:
-
Fabrizio Castro authored
Add the definitions for can0 and can1 to the SoC .dtsi. Signed-off-by:
-
Fabrizio Castro authored
CAN1 interface is exposed via connector J1 found on the HDMI daughter board. This patch enables can1 DT node from within the daughter board specific device tree. Signed-off-by:
-
Fabrizio Castro authored
This patch enables CAN0 interface exposed through connector J15 on the carrier board. Signed-off-by:
-
Fabrizio Castro authored
Add the definitions for can0 and can1 to the SoC .dtsi. Signed-off-by:
-
Fabrizio Castro authored
This patch enables the HDMI interface found on the expansion board. Signed-off-by:
-
Fabrizio Castro authored
Add du node to r8a7745 SoC DT. Boards that want to enable the DU need to specify the output topology. Signed-off-by:
-
Simon Horman authored
cec-clock is a fixed clock generator that is not controlled by i2c5 and thus should not be a child of the i2c5 bus node. Rather, it should be a child of the root node of the DT. Fixes: 02a5ab18 ("ARM: dts: koelsch: Add CEC clock for HDMI transmitter") Reported-by:
-
Fabrizio Castro authored
Signed-off-by:
Chris Paterson <chris.paterson2@renesas.com> Reviewed-by:
-
Simon Horman authored
Use newly added R-Car SDHI Gen2 fallback compat string in the DT of the r8a7794 SoC. This should have no run-time effect as the driver matches against the per-SoC compat string before considering the fallback compat string. Signed-off-by: -
Simon Horman authored
Use newly added R-Car SDHI Gen2 fallback compat string in the DT of the r8a7793 SoC. This should have no run-time effect as the driver matches against the per-SoC compat string before considering the fallback compat string. Signed-off-by: -
Simon Horman authored
Use newly added R-Car SDHI Gen2 fallback compat string in the DT of the r8a7792 SoC. This should have no run-time effect as the driver matches against the per-SoC compat string before considering the fallback compat string. Signed-off-by: -
Simon Horman authored
Use newly added R-Car SDHI Gen2 fallback compat string in the DT of the r8a7791 SoC. This should have no run-time effect as the driver matches against the per-SoC compat string before considering the fallback compat string. Signed-off-by: -
Simon Horman authored
Use newly added R-Car SDHI Gen2 fallback compat string in the DT of the r8a7790 SoC. This should have no run-time effect as the driver matches against the per-SoC compat string before considering the fallback compat string. Signed-off-by: -
Simon Horman authored
Use newly added R-Car SDHI Gen1 fallback compat string in the DT of the r8a7779 SoC. This should have no run-time effect as the driver matches against the per-SoC compat string before considering the fallback compat string. Signed-off-by: -
Simon Horman authored
Use newly added R-Car SDHI Gen1 fallback compat string in the DT of the r8a7778 SoC. This should have no run-time effect as the driver matches against the per-SoC compat string before considering the fallback compat string. Signed-off-by:
-
