This patch removes unnecessary out of memory message in hinic driver,
fixes the following checkpatch.pl warning:
"WARNING: Possible unnecessary 'out of memory' message"
Signed-off-by: Daode Huang <huangdaode@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using napi_alloc_skb in NAPI context avoids enable/disable IRQs, which
increases iperf3 result by a few Mbps. Since napi_alloc_skb() uses
NET_IP_ALIGN, convert other alloc methods to the same padding. Tested
on Intel Core2 and AMD K10 platforms.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changing to napi_gro_receive() improves efficiency significantly. Tested
on Intel Core2-based motherboards and iperf3.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Here is what Vladimir says about it:

  at803x_aneg_done() keeps the aneg reporting as "not done" even when
  the copper-side link was reported as up, but the in-band autoneg has
  not finished.

  That was the _intended_ behavior when that code was introduced, and
  Heiner have said about it [1]:

  | That's not nice from the PHY:
  | It signals "link up", and if the system asks the PHY for link details,
  | then it sheepishly says "well, link is *almost* up".

  If the specification of phy_aneg_done behavior does not include
  in-band autoneg (and it doesn't), then this piece of code does not
  belong here.

  The fact that we can no longer trigger this code from phylib is yet
  another reason why it fails at its intended (and wrong) purpose and
  should be removed.

Removing the SGMII link check, would just keep the call to
genphy_aneg_done(), which is also the fallback. Thus we can just remove
at803x_aneg_done() altogether.

[1] https://lore.kernel.org/netdev/fdf0074a-2572-5914-6f3e-77202cbf96de@gmail.com/Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using short intervals e.g. below one millisecond, large packets won't be
transmitted at all. The software implementations checks whether the packet can
be fit into the remaining interval. Therefore, it takes the packet length and
the transmission speed into account. That is correct.

However, for large packets it may be that the transmission time exceeds the
interval resulting in no packet transmission. The same situation works fine with
hardware offloading applied.

The problem has been observed with the following schedule and iperf3:

|tc qdisc replace dev lan1 parent root handle 100 taprio \
|   num_tc 8 \
|   map 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 \
|   queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
|   base-time $base \
|   sched-entry S 0x40 500000 \
|   sched-entry S 0xbf 500000 \
|   clockid CLOCK_TAI \
|   flags 0x00

[...]

|root@tsn:~# iperf3 -c 192.168.2.105
|Connecting to host 192.168.2.105, port 5201
|[  5] local 192.168.2.121 port 52610 connected to 192.168.2.105 port 5201
|[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
|[  5]   0.00-1.00   sec  45.2 KBytes   370 Kbits/sec    0   1.41 KBytes
|[  5]   1.00-2.00   sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes

After debugging, it seems that the packet length stored in the SKB is about
7000-8000 bytes. Using a 100 Mbit/s link the transmission time is about 600us
which larger than the interval of 500us.

Therefore, segment the SKB into smaller chunks if the packet is too big. This
yields similar results than the hardware offload:

|root@tsn:~# iperf3 -c 192.168.2.105
|Connecting to host 192.168.2.105, port 5201
|- - - - - - - - - - - - - - - - - - - - - - - - -
|[ ID] Interval           Transfer     Bitrate         Retr
|[  5]   0.00-10.00  sec  48.9 MBytes  41.0 Mbits/sec    0             sender
|[  5]   0.00-10.02  sec  48.7 MBytes  40.7 Mbits/sec                  receiver

Furthermore, the segmentation can be skipped for the full offload case, as the
driver or the hardware is expected to handle this.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

s/verfied/verified/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Lobakin says:

====================
net: avoid retpoline overhead on VLAN and TEB GRO

dev_gro_receive() uses indirect calls for IP GRO functions, but
it works only for the outermost headers and untagged frames.
Simple VLAN tag before an IP header restores the performance hit.
This simple series straightens the GRO calls for IP headers going
after VLAN tag or inner Ethernet header (GENEVE, NvGRE, VxLAN)
for retpolined kernels.
====================

The two most popular headers going after Ethernet are IPv4 and IPv6.
Retpoline overhead for them is addressed only in dev_gro_receive(),
when they lie right after the outermost Ethernet header.
Use the indirect call wrappers in TEB (Transparent Ethernet Bridging,
such as GENEVE, NvGRE, VxLAN etc.) GRO receive code to reduce the
penalty when processing the inner headers.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

The two most popular headers going after VLAN are IPv4 and IPv6.
Retpoline overhead for them is addressed only in dev_gro_receive(),
when they lie right after the outermost Ethernet header.
Use the indirect call wrappers in VLAN GRO receive code to reduce
the penalty on receiving tagged frames (when hardware stripping is
off or not available).
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

call_gro_receive() is used to limit GRO recursion, but it works only
with callback pointers.
There's a combined version of call_gro_receive() + INDIRECT_CALL_2()
in <net/inet_common.h>, but it doesn't check for IPv6 modularity.
Add a similar new helper to cover both of these. It can and will be
used to avoid retpoline overhead when IP header lies behind another
offloaded proto.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

If some source file includes <net/gro.h>, but doesn't include
<linux/indirect_call_wrapper.h>:

In file included from net/8021q/vlan_core.c:7:
./include/net/gro.h:6:1: warning: data definition has no type or storage class
    6 | INDIRECT_CALLABLE_DECLARE(struct sk_buff *ipv6_gro_receive(struct list_head *,
      | ^~~~~~~~~~~~~~~~~~~~~~~~~
./include/net/gro.h:6:1: error: type defaults to ‘int’ in declaration of ‘INDIRECT_CALLABLE_DECLARE’ [-Werror=implicit-int]

[...]

Include <linux/indirect_call_wrapper.h> directly. It's small and
won't pull lots of dependencies.
Also add some incomplete struct declarations to be fully stacked.

Fixes: 04f00ab2 ("net/core: move gro function declarations to separate header ")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

s/serisouly/seriously/

...and the sentence construction.
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic fixes

These are a few little fixes and cleanups found while working
on other features and more testing.
====================

Don't destroy the adminq while there is an outstanding request.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Up to now we've been ignoring any error return from the
queue starting in the link status check, so we fix that here.
If the driver had to reset and couldn't get things running
properly again, for example after a Tx Timeout and the FW is
not responding to commands, don't let the link watchdog try
to restart the queues.  At this point the user can try to DOWN
and UP the device to clear the errors.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Block some actions while the FW is in a reset activity
and the queues are not configured.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support in get_link_ksettings for a couple of
new BASET connections.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can get to the counter without going through the pointer
that the robot complained about.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The qcq->intr.index was set when the queue was allocated,
there is no need to reach around to find it.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Catch a couple of missing macro name uses, fix a couple
of misspellings, etc.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ocelot switches are a bit odd in that they do not have an STP state
to put the ports into. Instead, the forwarding configuration is delayed
from the typical port_bridge_join into stp_state_set, when the port enters
the BR_STATE_FORWARDING state.

I can only guess that the implementation of this quirk is the reason that
led to the simplification of the driver such that only one bridge could
be offloaded at a time.

We can simplify the data structures somewhat, and introduce a per-port
bridge device pointer and STP state, similar to how the LAG offload
works now (there we have a per-port bonding device pointer and TX
enabled state). This allows offloading multiple bridges with relative
ease, while still keeping in place the quirk to delay the programming of
the PGIDs.

We actually need this change now because we need to remove the bogus
restriction from ocelot_bridge_stp_state_set that ocelot->bridge_mask
needs to contain BIT(port), otherwise that function is a no-op.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a MRP ring was deleted or disabled, the driver was iterating over
the ports to detect if any other MPR rings exists and in case it didn't
exist it would delete the MAC table entry. But the problem was that it
used the last iterated port to delete the MAC table entry and this could
be a NULL port.

The fix consists of using the port on which the function was called.

Fixes: 7c588c3e ("net: ocelot: Extend MRP")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a virtual LAPB device's underlying Ethernet device closes, the LAPB
device is also closed.

However, currently the LAPB device is closed after the Ethernet device
closes. It would be better to close it before the Ethernet device closes.
This would allow the LAPB device to transmit a last frame to notify the
other side that it is disconnecting.
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pointer pfvf is being initialized with a value that is
never read and it is being updated later with a new value.  The
initialization is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Fixes: 56bcef52 ("octeontx2-af: Use npc_install_flow API for promisc and broadcast entries")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver data for the data interface has already been set by
usb_driver_claim_interface() so drop the subsequent redundant
assignment.

Note that this also avoids setting the driver data three times in case
of a combined interface.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: zuoqilin <zuoqilin@yulong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A typo is found out by codespell tool in 1734th line of drop_monitor.c:

$ codespell ./net/core/
./net/core/drop_monitor.c:1734: guarnateed  ==> guaranteed

Fix a typo found by codespell.
Signed-off-by: Xiong Zhenwu <xiong.zhenwu@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

A typo is found out by codespell tool in 111th line of hsr_debugfs.c:

$ codespell ./net/hsr/

net/hsr/hsr_debugfs.c:111: Debufs  ==> Debugfs

Fix typos found by codespell.
Signed-off-by: Xiong Zhenwu <xiong.zhenwu@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following W=1 kernel build warning(s):

 drivers/of/of_net.c:104: warning: Function parameter or member 'np' not described in 'of_get_mac_address'
 drivers/of/of_net.c:104: warning: expecting prototype for mac(). Prototype was for of_get_mac_address() instead

Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Intel mGbE variant implemented in EHL and TGL can be set to select
different clock frequency based on GPO bits in MAC_GPIO_STATUS register.

We introduce a new "void (*ptp_clk_freq_config)(void *priv)" in platform
data so that if a platform is required to configure the frequency of clock
source, in this case Intel mGBE does, the platform-specific configuration
of the PTP clock setting is done when stmmac_ptp_register() is called.
Signed-off-by: Wong, Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Co-developed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tobias Waldekranz says:

====================
net: dsa: mv88e6xxx: Offload bridge port flags

Add support for offloading learning and broadcast flooding flags. With
this in place, mv88e6xx supports offloading of all bridge port flags
that are currently supported by the bridge.

Broadcast flooding is somewhat awkward to control as there is no
per-port bit for this like there is for unknown unicast and unknown
multicast. Instead we have to update the ATU entry for the broadcast
address for all currently used FIDs.

v2 -> v3:
  - Only return a netdev from dsa_port_to_bridge_port if the port is
    currently bridged (Vladimir & Florian)

v1 -> v2:
  - Ensure that mv88e6xxx_vtu_get handles VID 0 (Vladimir)
  - Fixed off-by-one in mv88e6xxx_port_set_assoc_vector (Vladimir)
  - Fast age all entries on port when disabling learning (Vladimir)
  - Correctly detect bridge flags on LAG ports (Vladimir)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

These switches have two modes of classifying broadcast:

1. Broadcast is multicast.
2. Broadcast is its own unique thing that is always flooded
   everywhere.

This driver uses the first option, making sure to load the broadcast
address into all active databases. Because of this, we can support
per-port broadcast flooding by (1) making sure to only set the subset
of ports that have it enabled whenever joining a new bridge or VLAN,
and (2) by updating all active databases whenever the setting is
changed on a port.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow a user to control automatic learning per port.

Many chips have an explicit "LearningDisable"-bit that can be used for
this, but we opt for setting/clearing the PAV instead, as it works on
all devices at least as far back as 6083.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In accordance with the comment in dsa_port_bridge_leave, standalone
ports shall be configured to flood all types of traffic. This change
aligns the mv88e6xxx driver with that policy.

Previously a standalone port would initially not egress any unknown
traffic, but after joining and then leaving a bridge, it would.

This does not matter that much since we only ever send FROM_CPUs on
standalone ports, but it seems prudent to make sure that the initial
values match those that are applied after a bridging/unbridging cycle.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the conventional declaration style of a MAC address in the
kernel (u8 addr[ETH_ALEN]) for the broadcast address, then set it
using the existing helper.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hardware has a somewhat quirky protocol for reading out the VTU
entry for a particular VID. But there is no reason why we cannot
create a better API for ourselves in the driver.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the intricacies of correctly iterating over the VTU to a common
implementation.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a port is a part of a LAG, the ATU will create dynamic entries
belonging to the LAG ID when learning is enabled. So trying to
fast-age those out using the constituent port will have no
effect. Unfortunately the hardware does not support move operations on
LAGs so there is no obvious way to transform the request to target the
LAG instead.

Instead we document this known limitation and at least avoid wasting
any time on it.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order for a driver to be able to query a bridge for information
about itself, e.g. reading out port flags, it has to use a netdev that
is known to the bridge. In the simple case, that is just the netdev
representing the port, e.g. swp0 or swp1 in this example:

   br0
   / \
swp0 swp1

But in the case of an offloaded lag, this will be the bond or team
interface, e.g. bond0 in this example:

     br0
     /
  bond0
   / \
swp0 swp1

Add a helper that hides some of this complexity from the
drivers. Then, redefine dsa_port_offloads_bridge_port using the helper
to avoid double accounting of the set of possible offloaded uppers.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alex Elder says:

====================
net: ipa: support 32-bit targets

There is currently a configuration dependency that restricts IPA to
be supported only on 64-bit machines.  There are only a few things
that really require that, and those are fixed in this series.  The
last patch in the series removes the CONFIG_64BIT build dependency
for IPA.

Version 2 of this series uses upper_32_bits() rather than creating
a new function to extract bits out of a DMA address.  Version 3 of
uses lower_32_bits() as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>