If the device mac address is updated using ndo_set_mac_address(),
while the same mac address is already programmed, the driver does not
detect this condition if its netdev->dev_addr has been changed. The
driver tries to add the same mac address resulting in mac address
collision error. This has been observed in bonding mode-5 configuration.

To fix this, store the mac address configured in HW in the adapter
structure. Use this to compare against the new address being updated
to avoid collision.
Signed-off-by: Suresh Reddy <Suresh.Reddy@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a mac address is added to the uc_list and later the same mac address
is added via ndo_set_mac_address() or vice versa, the driver does not
detect this condition and tries to add it again. This results in a mac
address collision error when the FW rejects it.

Fix this by checking if the given mac address is present in uc_list while
setting the device mac address and vice versa. Similarly skip deletion if
the address is still in use in the other form.
Signed-off-by: Suresh Reddy <Suresh.Reddy@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver issues OPCODE_COMMON_GET_EXT_FAT_CAPABILITIES cmd during init which
when issued by VFs results in the logging of a cmd failure message since
they don't have the required privilege for this cmd. Fix by checking
privilege before issuing the cmd.

Also fixed typo in CAPABILITIES.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As per SLI guideline, drivers need to issue COMMON_RESET_FUNCTION SLI
cmd during driver unload to clean up any non-persistent state
information.
Issue this cmd only if VFs are not assigned to VMs as it is possible
for PF driver to unload while it\'s VF remains functional and assigned
to a VM.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch supports recovery from UEs caused due to Transient Parity
Errors (TPE), in BE2, BE3 and Skyhawk adapters. This change avoids
system reboot when such errors occur. The driver recovers from these
errors such that the adapter resumes full operational status as prior
to the UE.

Following is the list of changes in the driver to support this:

o The driver registers its UE recoverable capability with ARM FW at init
time. This also allows the driver to know if the feature is supported in
the FW.

o As the UE recovery requires precise time bound processing, the driver
creates its own error recovery work queue with a single worker thread (per
module, shared across functions).

o Each function runs an error detection task at an interval of 1 second as
required by the FW. The error detection logic already exists for BEx/SH,
but it now runs in the context of a separate worker thread.

o When an error is detected by the task, if it is recoverable, the PF0
driver instance initiates a soft reset, while other PF driver instances
wait for the reset to complete and the chip to become ready. Once
the chip is ready, all driver instances including PF0, resume to
reinitialize the respective functions.

o The PF0 driver checks for some recovery criteria, to determine if the
recovery can be initiated. If the criteria is not met, the PF0 driver does
not initiate a soft reset, it retains the existing behavior to stop
further processing and requires a reboot to get the chip to operational
state again.

o To allow each function to share the workq, while also making progress in
its recovery process, a per-function recovery state machine is used.
The per-function tasks avoid blocking operations like msleep() while in
this state machine (until reinit state) and instead reschedule for the
required delay.

o With these changes, the existing error recovery code for Lancer also
runs in the context of the new worker thread.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On some systems (such as the Qualcomm APQ8060 Dragonboard) the
RESET signal of the SMSC911x is not pulled up by a resistor (or
the internal pull-up that will pull it up if the pin is not
even connected) but instead connected to a GPIO line, so that
the operating system must explicitly deassert RESET before use.

Support this in the SMSC911x driver so this ethernet connector
can be used on such targets.

Notice that we request the line to go logical low (deassert)
whilst the line on the actual component is active low. This
is managed in the respective hardware description when
specifying the GPIO line with e.g. device tree or ACPI. With
device tree it looks like this in one case:

  reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;

Which means that logically requesting the RESET line to be
deasserted will result in the line being driven high, taking
the device out of reset.

Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds device tree bindings for:

- An optional GPIO line for releasing the RESET signal to the
  SMSC911x devices

- An optional PME (power management event) interrupt line that
  can be utilized to wake up the system on network activity.
  This signal exist on all the SMSC911x devices, it is just not
  very often routed.

Both these lines are routed to the SoC on the Qualcomm APQ8060
Dragonboard and thus needs to be bound in the device tree.

Cc: devicetree@vger.kernel.org
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tomer Tayar says:

====================
qed*: Debug data collection

This patch series adds the support of debug data collection in the qed driver,
and the means to extract it in the qede driver via the get_regs operation.

Changes from V1:
- Respin of the series after rebasing next-next.
- Remove the first patch as it seems that its V1 version was already applied
  (commit '4102426f').
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the support for dumping and formatting the HW/FW debug data.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SOme statements in the driver only served to inform
which functions were entered. Ftrace can do that just as good without
needing memory. Remove the statements.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We get 4 warnings when building kernel with W=1:
drivers/net/ethernet/qlogic/qed/qed_selftest.c:6:5: warning: no previous prototype for 'qed_selftest_memory' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:19:5: warning: no previous prototype for 'qed_selftest_interrupt' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:32:5: warning: no previous prototype for 'qed_selftest_register' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:55:5: warning: no previous prototype for 'qed_selftest_clock' [-Wmissing-prototypes]

In fact, these functions are declared in qed_selftest.h, so this patch
add missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

udp_diag_destroy does look up the IPv4 UDP hashtable for mapped
addresses, but it gets the IPv4 address to look up from the
beginning of the IPv6 address instead of the end.

Tested: https://android-review.googlesource.com/269874
Fixes: 5d77dca8 ("net: diag: support SOCK_DESTROY for UDP sockets")
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This bug was detected by kmemleak:
unreferenced object 0xffff8804269cc3c0 (size 64):
  comm "criu", pid 1042, jiffies 4294907360 (age 13.713s)
  hex dump (first 32 bytes):
    a0 32 cc 2c 04 88 ff ff 00 00 00 00 00 00 00 00  .2.,............
    00 01 00 00 00 00 ad de 00 02 00 00 00 00 ad de  ................
  backtrace:
    [<ffffffff8184dffa>] kmemleak_alloc+0x4a/0xa0
    [<ffffffff8124720f>] kmem_cache_alloc_trace+0x10f/0x280
    [<ffffffffa02864cc>] __netlink_diag_dump+0x26c/0x290 [netlink_diag]

v2: don't remove a reference on a rhashtable_iter structure to
    release it from netlink_diag_dump_done

Cc: Herbert Xu <herbert@gondor.apana.org.au>
Fixes: ad202074 ("netlink: Use rhashtable walk interface in diag dump")
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-rewrite-20160907-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Local abort tracepoint

Here are two patches.  They need to be applied on top of the just-posted
call refcount overhaul patch:

 (1) Fix the return value of some call completion helpers.

 (2) Add a tracepoint that allows local aborts to be debugged.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-rewrite-20160907-1' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Overhaul call refcounting

Here's a set of mostly small patches leading up to one big one.

The big patch at the end of the series overhauls how rxrpc_call refcounting
is handled, making it more sane so that calls bound to user IDs are _only_
released from socket operations or kernel API functions.  Further, the
patch stops calls from holding refs on their parent socket - which can
prevent the socket from being cleaned up.

The second largest patch improves the call tracking tracepoint by providing
extra information about the situation in which gets and puts occur.  This
allows distinctions to be drawn between refs held by the socket user ID
tree, refs held by the work queue (to be implemented by a future patch) and
other refs.

The other patches include a couple of cleanups and some simple alterations
to avoid NULL pointer dereferences in the big patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a tracepoint for working out where local aborts happen.  Each
tracepoint call is labelled with a 3-letter code so that they can be
distinguished - and the DATA sequence number is added too where available.

rxrpc_kernel_abort_call() also takes a 3-letter code so that AFS can
indicate the circumstances when it aborts a call.
Signed-off-by: David Howells <dhowells@redhat.com>

rxrpc_set_call_completion() returns bool, not int, so the ret variable
should match this.

rxrpc_call_completed() and __rxrpc_call_completed() should return the value
of rxrpc_set_call_completion().
Signed-off-by: David Howells <dhowells@redhat.com>

rxrpc calls shouldn't hold refs on the sock struct.  This was done so that
the socket wouldn't go away whilst the call was in progress, such that the
call could reach the socket's queues.

However, we can mark the socket as requiring an RCU release and rely on the
RCU read lock.

To make this work, we do:

 (1) rxrpc_release_call() removes the call's call user ID.  This is now
     only called from socket operations and not from the call processor:

	rxrpc_accept_call() / rxrpc_kernel_accept_call()
	rxrpc_reject_call() / rxrpc_kernel_reject_call()
	rxrpc_kernel_end_call()
	rxrpc_release_calls_on_socket()
	rxrpc_recvmsg()

     Though it is also called in the cleanup path of
     rxrpc_accept_incoming_call() before we assign a user ID.

 (2) Pass the socket pointer into rxrpc_release_call() rather than getting
     it from the call so that we can get rid of uninitialised calls.

 (3) Fix call processor queueing to pass a ref to the work queue and to
     release that ref at the end of the processor function (or to pass it
     back to the work queue if we have to requeue).

 (4) Skip out of the call processor function asap if the call is complete
     and don't requeue it if the call is complete.

 (5) Clean up the call immediately that the refcount reaches 0 rather than
     trying to defer it.  Actual deallocation is deferred to RCU, however.

 (6) Don't hold socket refs for allocated calls.

 (7) Use the RCU read lock when queueing a message on a socket and treat
     the call's socket pointer according to RCU rules and check it for
     NULL.

     We also need to use the RCU read lock when viewing a call through
     procfs.

 (8) Transmit the final ACK/ABORT to a client call in rxrpc_release_call()
     if this hasn't been done yet so that we can then disconnect the call.
     Once the call is disconnected, it won't have any access to the
     connection struct and the UDP socket for the call work processor to be
     able to send the ACK.  Terminal retransmission will be handled by the
     connection processor.

 (9) Release all calls immediately on the closing of a socket rather than
     trying to defer this.  Incomplete calls will be aborted.

The call refcount model is much simplified.  Refs are held on the call by:

 (1) A socket's user ID tree.

 (2) A socket's incoming call secureq and acceptq.

 (3) A kernel service that has a call in progress.

 (4) A queued call work processor.  We have to take care to put any call
     that we failed to queue.

 (5) sk_buffs on a socket's receive queue.  A future patch will get rid of
     this.

Whilst we're at it, we can do:

 (1) Get rid of the RXRPC_CALL_EV_RELEASE event.  Release is now done
     entirely from the socket routines and never from the call's processor.

 (2) Get rid of the RXRPC_CALL_DEAD state.  Calls now end in the
     RXRPC_CALL_COMPLETE state.

 (3) Get rid of the rxrpc_call::destroyer work item.  Calls are now torn
     down when their refcount reaches 0 and then handed over to RCU for
     final cleanup.

 (4) Get rid of the rxrpc_call::deadspan timer.  Calls are cleaned up
     immediately they're finished with and don't hang around.
     Post-completion retransmission is handled by the connection processor
     once the call is disconnected.

 (5) Get rid of the dead call expiry setting as there's no longer a timer
     to set.

 (6) rxrpc_destroy_all_calls() can just check that the call list is empty.
Signed-off-by: David Howells <dhowells@redhat.com>

Use rxrpc_is_service_call() rather than rxrpc_conn_is_service() if the call
is available just in case call->conn is NULL.
Signed-off-by: David Howells <dhowells@redhat.com>

Pass the connection pointer to rxrpc_post_packet_to_call() as the call
might get disconnected whilst we're looking at it, but the connection
pointer determined by rxrpc_data_read() is guaranteed by RCU for the
duration of the call.
Signed-off-by: David Howells <dhowells@redhat.com>

Cache the security index in the rxrpc_call struct so that we can get at it
even when the call has been disconnected and the connection pointer
cleared.
Signed-off-by: David Howells <dhowells@redhat.com>

Use call->peer rather than call->conn->params.peer to avoid the possibility
of call->conn being NULL and, whilst we're at it, check it for NULL before we
access it.
Signed-off-by: David Howells <dhowells@redhat.com>

Improve the call tracking tracepoint by showing more differentiation
between some of the put and get events, including:

  (1) Getting and putting refs for the socket call user ID tree.

  (2) Getting and putting refs for queueing and failing to queue the call
      processor work item.

Note that these aren't necessarily used in this patch, but will be taken
advantage of in future patches.

An enum is added for the event subtype numbers rather than coding them
directly as decimal numbers and a table of 3-letter strings is provided
rather than a sequence of ?: operators.
Signed-off-by: David Howells <dhowells@redhat.com>

Delete rxrpc_kernel_free_skb() as it's unused.
Signed-off-by: David Howells <dhowells@redhat.com>

Remove some whitespace.
Signed-off-by: David Howells <dhowells@redhat.com>

gpio_to_irq does not return NO_IRQ but instead returns a negative
error code on failure. Returning NO_IRQ from the function has no
negative effects as we only compare the result to the expected
interrupt number, but it's better to return a proper failure
code for consistency, and we should remove NO_IRQ from the kernel
entirely.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Ma Yuying <yuma@redhat.com>
Suggested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The newly added bpf_overflow_handler function is only built of both
CONFIG_EVENT_TRACING and CONFIG_BPF_SYSCALL are enabled, but the caller
only checks the latter:

kernel/events/core.c: In function 'perf_event_alloc':
kernel/events/core.c:9106:27: error: 'bpf_overflow_handler' undeclared (first use in this function)

This changes the caller so we also skip this call if CONFIG_EVENT_TRACING
is disabled entirely.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: aa6a5f3c ("perf, bpf: add perf events core support for BPF_PROG_TYPE_PERF_EVENT programs")
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We get 1 warning when building kernel with W=1:
drivers/net/ethernet/arc/emac_mdio.c:107:5: warning: no previous prototype for 'arc_mdio_reset' [-Wmissing-prototypes]

In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We get a few warnings when building kernel with W=1:
drivers/net/usb/lan78xx.c:1182:6: warning: no previous prototype for 'lan78xx_defer_kevent' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:1409:5: warning: no previous prototype for 'lan78xx_nway_reset' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:2000:5: warning: no previous prototype for 'lan78xx_set_mac_addr' [-Wmissing-prototypes]
....

In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds support for several infrastructure operations that are done as part of
debug data collection.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These messages are unnecessary as OOM allocation failures already do
a dump_stack() giving more or less the same information.

$ size drivers/net/ethernet/qlogic/qed/built-in.o* (defconfig x86-64)
   text	   data	    bss	    dec	    hex	filename
 127817	  27969	  32800	 188586	  2e0aa	drivers/net/ethernet/qlogic/qed/built-in.o.new
 132474	  27969	  32800	 193243	  2f2db	drivers/net/ethernet/qlogic/qed/built-in.o.old

Miscellanea:

o Change allocs to the generally preferred forms where possible.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-rewrite-20160904-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Split output code from sendmsg code

Here's a set of small patches that split the packet transmission code from
the sendmsg code and simply rearrange the new file to make it more
logically laid out ready for being rewritten.  An enum is also moved out of
the header file to there as it's only used there.  This needs to be applied
on top of the just-posted fixes patch set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-rewrite-20160904-1' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Small fixes

Here's a set of small fix patches:

 (1) Fix some uninitialised variables.

 (2) Set the client call state before making it live by attaching it to the
     conn struct.

 (3) Randomise the epoch and starting client conn ID values, and don't
     change the epoch when the client conn ID rolls round.

 (4) Replace deprecated create_singlethread_workqueue() calls.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If vxlan_build_skb return err < 0, tx_errors should be also increased.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Depending on the preempt mode, the bpf_prog stored in xdp_prog may be
freed despite the use of call_rcu inside bpf_prog_put. The situation is
possible when running in PREEMPT_RCU=y mode, for instance, since the rcu
callback for destroying the bpf prog can run even during the bh handling
in the mlx4 rx path.

Several options were considered before this patch was settled on:

Add a napi_synchronize loop in mlx4_xdp_set, which would occur after all
of the rings are updated with the new program.
This approach has the disadvantage that as the number of rings
increases, the speed of update will slow down significantly due to
napi_synchronize's msleep(1).

Add a new rcu_head in bpf_prog_aux, to be used by a new bpf_prog_put_bh.
The action of the bpf_prog_put_bh would be to then call bpf_prog_put
later. Those drivers that consume a bpf prog in a bh context (like mlx4)
would then use the bpf_prog_put_bh instead when the ring is up. This has
the problem of complexity, in maintaining proper refcnts and rcu lists,
and would likely be harder to review. In addition, this approach to
freeing must be exclusive with other frees of the bpf prog, for instance
a _bh prog must not be referenced from a prog array that is consumed by
a non-_bh prog.

The placement of rcu_read_lock in this patch is functionally the same as
putting an rcu_read_lock in napi_poll. Actually doing so could be a
potentially controversial change, but would bring the implementation in
line with sk_busy_loop (though of course the nature of those two paths
is substantially different), and would also avoid future copy/paste
problems with future supporters of XDP. Still, this patch does not take
that opinionated option.

Testing was done with kernels in either PREEMPT_RCU=y or
CONFIG_PREEMPT_VOLUNTARY=y+PREEMPT_RCU=n modes, with neither exhibiting
any drawback. With PREEMPT_RCU=n, the extra call to rcu_read_lock did
not show up in the perf report whatsoever, and with PREEMPT_RCU=y the
overhead of rcu_read_lock (according to perf) was the same before/after.
In the rx path, rcu_read_lock is eventually called for every packet
from netif_receive_skb_internal, so the napi poll call's rcu_read_lock
is easily amortized.

v2:
Remove extra rcu_read_lock in mlx4_en_process_rx_cq body
Annotate xdp_prog with __rcu, and convert all usages to rcu_assign or
rcu_dereference[_protected] as appropriate.
Add explicit mutex lock around rcu_assign instead of xchg loop.

Fixes: d576acf0 ("net/mlx4_en: add page recycle to prepare rx ring for tx support")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sean Wang says:

====================
net: ethernet: mediatek: add enhancements to RX path

Changes since v1:
- fix message typos and add coverletter

Changes since v2:
- split from the previous series for submitting add enhancements as
a series targeting 'net-next' and add indents before comments.

Changes since v3:
- merge the patch using PDMA RX path
- fixed the input of mtk_poll_rx is with the remaining budget

Changes since v4:
- save one wmb and register update when no packet is being handled
inside mtk_poll_rx call
- fixed incorrect return packet count from mtk_napi_rx
====================
Signed-off-by: David S. Miller <davem@davemloft.net>