Convert the advantechwdt watchdog into a platform_device
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Put the set_heartbeat/timeout code into a seperate function
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This cleanup consists of:
- make sure that the printk's use the module/driver-name
- do the exit of the module exactly the opposite of the init of the module
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Convert the reboot_notifier into the platform_device's shutdown
method
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Convert the acquirewdt watchdog into a platform_device
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Clean the current code before we convert the driver to a platform_device.
This clean consists of:
- document the includes
- make sure that the printk's use the module/driver-name
- do the exit of the module exactly the opposite of the init of the module
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The PCWD cards normally use the heartbeat that is set via
the dip-switches of the card. There are only 3 switches,
thus 8 combinations that each have a certain heartbeat.
The card can however be programmed with a heartbeat from
1 till 65535 seconds. This is what our driver does: it
programs the heartbeat on the card.

There are however a lot of people that don't know that
we set the heartbeat of the watchdog card to the value
provided by the heartbeat module parameter. Instead they
think that the heartbeat value is the same as set by the
dip-switches.

This patch changes the driver so that at startup you can
take the heartbeat from the dip-switches. You do this
by setting the heartbeat module parameter to 0. This
patch also makes this the default behaviour.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

update Simon Machell's e-mail adres
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The PCWD cards normally use the heartbeat that is set via
the dip-switches of the card. There are only 3 switches,
thus 8 combinations that each have a certain heartbeat.
The card can however be programmed with a heartbeat from
1 till 65535 seconds. This is what our driver does: it
programs the heartbeat on the card.

There are however a lot of people that don't know that
we set the heartbeat of the watchdog card to the value
provided by the heartbeat module parameter. Instead they
think that the heartbeat value is the same as set by the
dip-switches.

This patch changes the driver so that at startup you can
take the heartbeat from the dip-switches. You do this
by setting the heartbeat module parameter to 0. This
patch also makes this the default behaviour.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

document and review the include files.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

the keepalive and get_temperature functions should
use spinlocks also.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The PCWD cards normally use the heartbeat that is set via
the dip-switches of the card. There are only 3 switches,
thus 8 combinations that each have a certain heartbeat.
The card can however be programmed with a heartbeat from
1 till 65535 seconds. This is what our driver does: it
programs the heartbeat on the card.

There are however a lot of people that don't know that
we set the heartbeat of the watchdog card to the value
provided by the heartbeat module parameter. Instead they
think that the heartbeat value is the same as set by the
dip-switches.

This patch changes the driver so that at startup you can
take the heartbeat from the dip-switches. You do this
by setting the heartbeat module parameter to 0. This
patch also makes this the default behaviour.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The return value of clk_get() should be checked by IS_ERR().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Cleanup the s3c2410_wdt driver's exit point by
using labels instead of multiple returns. Also
remove the checks for the resources having been
allocate in the exit, as we will now either have
fully allocated or not allocated the resources
at-all.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] longhaul compile fix.
  [CPUFREQ] Advise not to use longhaul on VIA C7.
  [CPUFREQ] set policy->curfreq on initialization
  [CPUFREQ] Trivial cleanup for acpi read/write port in acpi-cpufreq.c
  [CPUFREQ] fixes typo in cpufreq.c

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Recent workqueue changes basically make this a formal requirement.

Also, move atomic32.o from lib-y to obj-y since it exports symbols
to modules.
Signed-off-by: David S. Miller <davem@davemloft.net>

Some gcc's are more anal than others about empty switch labels.
error: label at end of compound statement
Signed-off-by: Dave Jones <davej@redhat.com>

C7's are centrino speedstep-alike.
Signed-off-by: Dave Jones <davej@redhat.com>

Check the correct variable and set policy->cur upon acpi-cpufreq
initialization to allow the userspace governor to be used as default.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-by: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

"sunkbd_enable(sunkbd, 0);" has no effect. Adding "sunkbd->enabled =
enable" in sunkbd_enable (obvious)
Signed-off-by: Fabrice Knevez <nuxdoors@cegetel.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

desc-status --> desc->status
Signed-off-by: David S. Miller <davem@davemloft.net>

Use struct irq_chip instead of hw_interrupt_type.

Delete hw_resend_irq(), totally unused.
Signed-off-by: David S. Miller <davem@davemloft.net>

It branches around some necessary prom calls, which we would
need to do even if we are mapped at the correct location already.
So it doesn't work.

The idea was that this sort of thing could be used for the eventual
kexec implementation, but it is clear that this will need to be
done differently.
Signed-off-by: David S. Miller <davem@davemloft.net>

fix a typo, sys_mincore() needs min().
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus "I'm a moron" Torvalds <torvalds@osdl.org>

amikbd: missing declaration
sun3_NCR5380: more work_struct mess
sun3_NCR5380: cast is not an lvalue
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Hugh Dickins correctly points out that mincore() is actually _supposed_
to fail on an unmapped hole in the user address space, rather than
return valid ("empty") information about the hole.  This just simplifies
the problem further (I had been misled by our previous confusing and
complicated way of doing mincore()).

Also, in the unlikely situation that we can't allocate a temporary
kernel buffer, we should actually return EAGAIN, not ENOMEM, to keep the
"unmapped hole" and "allocation failure" error cases separate.

Finally, add a comment about our stupid historical lack of support for
anonymous mappings.  I'll fix that if somebody reminds me after 2.6.20
is out.
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
  IB/mthca: Use DEFINE_MUTEX() instead of mutex_init()
  IB/mthca: Add HCA profile module parameters
  IB/srp: Fix FMR mapping for 32-bit kernels and addresses above 4G
  IB: Fix ib_dma_alloc_coherent() wrapper

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [PATCH] pata_via: Cable detect error
  [PATCH] Fix help text for CONFIG_ATA_PIIX
  [PATCH] initializer entry defined twice in pata_rz1000
  [PATCH] ata: fix platform_device_register_simple() error check
  [PATCH] ahci: do not mangle saved HOST_CAP while resetting controller
  [PATCH] libata: don't initialize sg in ata_exec_internal() if DMA_NONE (take #2)
  [libata] sata_svw: Disable ATAPI DMA on current boards (errata workaround)
  [libata] use kmap_atomic(KM_IRQ0) in SCSI simulator
  [PATCH] ata_piix: use piix_host_stop() in ich_pata_ops
  [PATCH] ata_piix: IDE mode SATA patch for Intel ICH9

On architectures where the atomicity of the bit operations is handled by
external means (ie a separate spinlock to protect concurrent accesses),
just doing a direct assignment on the workqueue data field (as done by
commit 4594bf15) can cause the
assignment to be lost due to lack of serialization with the bitops on
the same word.

So we need to serialize the assignment with the locks on those
architectures (notably older ARM chips, PA-RISC and sparc32).

So rather than using an "unsigned long", let's use "atomic_long_t",
which already has a safe assignment operation (atomic_long_set()) on
such architectures.

This requires that the atomic operations use the same atomicity locks as
the bit operations do, but that is largely the case anyway.  Sparc32
will probably need fixing.

Architectures (including modern ARM with LL/SC) that implement sane
atomic operations for SMP won't see any of this matter.

Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: David Miller <davem@davemloft.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Linux Arch Maintainers <linux-arch@vger.kernel.org>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Doug Chapman noticed that mincore() will doa "copy_to_user()" of the
result while holding the mmap semaphore for reading, which is a big
no-no.  While a recursive read-lock on a semaphore in the case of a page
fault happens to work, we don't actually allow them due to deadlock
schenarios with writers due to fairness issues.

Doug and Marcel sent in a patch to fix it, but I decided to just rewrite
the mess instead - not just fixing the locking problem, but making the
code smaller and (imho) much easier to understand.

Cc: Doug Chapman <dchapman@redhat.com>
Cc: Marcel Holtmann <holtmann@redhat.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The UDMA66 VIA hardware has no controller side cable detect bits we can
use. This patch minimally fixes the problem by reporting unknown in this
case and using drive side detection.

The old drivers/ide code does some additional tricks but those aren't
appropriate now we are in -rc.

Without this update UDMA66 via controllers run slowly. They don't fail so
it's a borderline call whether this is -rc material or not.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

> Thanks for clarifying Bill, and sorry Alan. ata_piix does indeed work
> correctly. The help text is a bit confusing:
>
> config ATA_PIIX
>         tristate "Intel PIIX/ICH SATA support"
>         depends on PCI
>         help
>           This option enables support for ICH5/6/7/8 Serial ATA.
>           If PATA support was enabled previously, this enables
>           support for select Intel PIIX/ICH PATA host controllers.

New help text
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This removes the extra definition of the .error_handler member
in the pata_rz1000 driver.
Signed-off-by: Ira W. Snyder <kernel@irasnyder.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The return value of platform_device_register_simple() should be checked
by IS_ERR().

Cc: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Do not mangle with HOST_CAP while resetting controller.  The code is
there for a historical reason.  The mangling breaks controller feature
detection and 0 PORTS_IMPL workaround code.

This problem was spotted by Manoj Kasichainula.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Manoj Kasichainula <manoj@io.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Calling sg_init_one() with NULL buf causes oops on certain
configurations.  Don't initialize sg in ata_exec_internal() if
DMA_NONE and make the function complain if @buf is NULL when dma_dir
isn't DMA_NONE.  While at it, fix comment.

The problem is discovered and initial patch was submitted by Arnd
Bergmann.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Current Broadcom/Serverworks SATA boards (including Apple K2 SATA)
have problems with ATAPI DMA, so it is disabled.  ATAPI PIO, ATA PIO,
and ATA DMA continue to work just fine.
Acked-by: Anantha Subramanyam <ananth@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>