Due to the HW design, master IRQs are timing critical, so give them
precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.

In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

We want to reuse this function later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

After making sure to reinit the HW and clear interrupts in the timeout
case, we know that interrupts are always disabled in the sections
protected by the spinlock. Thus, we can simply remove it which is a
preparation for further refactoring. While here, rename the timeout
variable to time_left which is way more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

When calculating the bus speed, the clock should be on, of course. Most
bootloaders left them on, so this went unnoticed so far.

Move the ioremapping out of this clock-enabled-block and prepare for
adding hw initialization there, too.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull nouveau and radeon fixes from Dave Airlie:
 "Just some nouveau and radeon/amdgpu fixes.

  The nouveau fixes look large as the firmware context files are
  regenerated, but the actual change is quite small"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: make some dpm errors debug only
  drm/nouveau/volt/pwm/gk104: fix an off-by-one resulting in the voltage not being set
  drm/nouveau/nvif: allow userspace access to its own client object
  drm/nouveau/gr/gf100-: fix oops when calling zbc methods
  drm/nouveau/gr/gf117-: assume no PPC if NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK is zero
  drm/nouveau/gr/gf117-: read NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK from correct GPC
  drm/nouveau/gr/gf100-: split out per-gpc address calculation macro
  drm/nouveau/bios: return actual size of the buffer retrieved via _ROM
  drm/nouveau/instmem: protect instobj list with a spinlock
  drm/nouveau/pci: enable c800 magic for some unknown Samsung laptop
  drm/nouveau/pci: enable c800 magic for Clevo P157SM
  drm/radeon: make rv770_set_sw_state failures non-fatal
  drm/amdgpu: move dependency handling out of atomic section v2
  drm/amdgpu: optimize scheduler fence handling
  drm/amdgpu: remove vm->mutex
  drm/amdgpu: add mutex for ba_va->valids/invalids
  drm/amdgpu: adapt vce session create interface changes
  drm/amdgpu: vce use multiple cache surface starting from stoney
  drm/amdgpu: reset vce trap interrupt flag

Pull RTC fixes from Alexandre Belloni:
 "Two fixes for the ds1307 alarm and wakeup"

* tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  rtc: ds1307: fix alarm reading at probe time
  rtc: ds1307: fix kernel splat due to wakeup irq handling

Pull MIPS fix from Ralf Baechle:
 "Just a fix for empty loops that may be removed by non-antique GCC"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix delay loops which may be removed by GCC.

Pull m68k fixes from Geert Uytterhoeven:
 "Summary:

   - Add missing initialization of max_pfn, which is needed to make
     selftests/vm/mlock2-tests succeed,

   - Wire up new mlock2 syscall"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Wire up mlock2
  m68knommu: Add missing initialization of max_pfn and {min,max}_low_pfn
  m68k/mm: sun3 - Add missing initialization of max_pfn and {min,max}_low_pfn
  m68k/mm: m54xx - Add missing initialization of max_pfn
  m68k/mm: motorola - Add missing initialization of max_pfn

Pull ARM fixes from Russell King:
 "Just two changes this time around:

   - wire up the new mlock2 syscall added during the last merge window

   - fix a build problem with certain configurations provoked by making
     CONFIG_OF user selectable"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8454/1: OF implies OF_FLATTREE
  ARM: wire up mlock2 syscall

Pull SCSI target fixes from Nicholas Bellinger:
 - fix tcm-user backend driver expired cmd time processing (agrover)
 - eliminate kref_put_spinlock_irqsave() for I/O completion (bart)
 - fix iscsi login kthread failure case hung task regression (nab)
 - fix COMPARE_AND_WRITE completion use-after-free race (nab)
 - fix COMPARE_AND_WRITE with SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC non zero
   SGL offset data corruption.  (Jan + Doug)
 - fix >= v4.4-rc1 regression for tcm_qla2xxx enable configfs attribute
   (Himanshu + HCH)

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target/stat: print full t10_wwn.model buffer
  target: fix COMPARE_AND_WRITE non zero SGL offset data corruption
  qla2xxx: Fix regression introduced by target configFS changes
  kref: Remove kref_put_spinlock_irqsave()
  target: Invoke release_cmd() callback without holding a spinlock
  target: Fix race for SCF_COMPARE_AND_WRITE_POST checking
  iscsi-target: Fix rx_login_comp hang after login failure
  iscsi-target: return -ENOMEM instead of -1 in case of failed kmalloc()
  target/user: Do not set unused fields in tcmu_ops
  target/user: Fix time calc in expired cmd processing

Pull thermal management fixes from Zhang Rui:
 "Specifics:

 - several fixes and cleanups on Rockchip thermal drivers.

 - add the missing support of RK3368 SoCs in Rockchip driver.

 - small fixes on of-thermal, power_allocator, rcar driver, IMX, and
   QCOM drivers, and also compilation fixes, on thermal.h, when thermal
   is not selected"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  imx: thermal: use CPU temperature grade info for thresholds
  thermal: fix thermal_zone_bind_cooling_device prototype
  Revert "thermal: qcom_spmi: allow compile test"
  thermal: rcar_thermal: remove redundant operation
  thermal: of-thermal: Reduce log level for message when can't fine thermal zone
  thermal: power_allocator: Use temperature reading from tz
  thermal: rockchip: Support the RK3368 SoCs in thermal driver
  thermal: rockchip: consistently use int for temperatures
  thermal: rockchip: Add the sort mode for adc value increment or decrement
  thermal: rockchip: improve the conversion function
  thermal: rockchip: trivial: fix typo in commit
  thermal: rockchip: better to compatible the driver for different SoCs
  dt-bindings: rockchip-thermal: Support the RK3368 SoCs compatible

Cut 'n paste error saw it only process sizeof(t10_wwn.vendor) characters.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

target_core_sbc's compare_and_write functionality suffers from taking
data at the wrong memory location when writing a CAW request to disk
when a SGL offset is non-zero.

This can happen with loopback and vhost-scsi fabric drivers when
SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC is used to map existing user-space
SGL memory into COMPARE_AND_WRITE READ/WRITE payload buffers.

Given the following sample LIO subtopology,

% targetcli ls /loopback/
o- loopback ................................. [1 Target]
  o- naa.6001405ebb8df14a ....... [naa.60014059143ed2b3]
    o- luns ................................... [2 LUNs]
      o- lun0 ................ [iblock/ram0 (/dev/ram0)]
      o- lun1 ................ [iblock/ram1 (/dev/ram1)]
% lsscsi -g
[3:0:1:0]    disk    LIO-ORG  IBLOCK           4.0   /dev/sdc   /dev/sg3
[3:0:1:1]    disk    LIO-ORG  IBLOCK           4.0   /dev/sdd   /dev/sg4

the following bug can be observed in Linux 4.3 and 4.4~rc1:

% perl -e 'print chr$_ for 0..255,reverse 0..255' >rand
% perl -e 'print "\0" x 512' >zero
% cat rand >/dev/sdd
% sg_compare_and_write -i rand -D zero --lba 0 /dev/sdd
% sg_compare_and_write -i zero -D rand --lba 0 /dev/sdd
Miscompare reported
% hexdump -Cn 512 /dev/sdd
00000000  0f 0e 0d 0c 0b 0a 09 08  07 06 05 04 03 02 01 00
00000010  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00
*
00000200

Rather than writing all-zeroes as instructed with the -D file, it
corrupts the data in the sector by splicing some of the original
bytes in. The page of the first entry of cmd->t_data_sg includes the
CDB, and sg->offset is set to a position past the CDB. I presume that
sg->offset is also the right choice to use for subsequent sglist
members.
Signed-off-by: Jan Engelhardt <jengelh@netitwork.de>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

this patch fixes following regression

 # targetcli
 [Errno 13] Permission denied: '/sys/kernel/config/target/qla2xxx/21:00:00:0e:1e:08:c7:20/tpgt_1/enable'

Fixes: 2eafd729 ("target: use per-attribute show and store methods")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

The last user is gone. Hence remove this function.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

This patch fixes the following kernel warning because it avoids that
IRQs are disabled while ft_release_cmd() is invoked (fc_seq_set_resp()
invokes spin_unlock_bh()):

WARNING: CPU: 3 PID: 117 at kernel/softirq.c:150 __local_bh_enable_ip+0xaa/0x110()
Call Trace:
 [<ffffffff814f71eb>] dump_stack+0x4f/0x7b
 [<ffffffff8105e56a>] warn_slowpath_common+0x8a/0xc0
 [<ffffffff8105e65a>] warn_slowpath_null+0x1a/0x20
 [<ffffffff81062b2a>] __local_bh_enable_ip+0xaa/0x110
 [<ffffffff814ff229>] _raw_spin_unlock_bh+0x39/0x40
 [<ffffffffa03a7f94>] fc_seq_set_resp+0xe4/0x100 [libfc]
 [<ffffffffa02e604a>] ft_free_cmd+0x4a/0x90 [tcm_fc]
 [<ffffffffa02e6972>] ft_release_cmd+0x12/0x20 [tcm_fc]
 [<ffffffffa042bd66>] target_release_cmd_kref+0x56/0x90 [target_core_mod]
 [<ffffffffa042caf0>] target_put_sess_cmd+0xc0/0x110 [target_core_mod]
 [<ffffffffa042cb81>] transport_release_cmd+0x41/0x70 [target_core_mod]
 [<ffffffffa042d975>] transport_generic_free_cmd+0x35/0x420 [target_core_mod]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joern Engel <joern@logfs.org>
Reviewed-by: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

This patch addresses a race + use after free where the first
stage of COMPARE_AND_WRITE in compare_and_write_callback()
is rescheduled after the backend sends the secondary WRITE,
resulting in second stage compare_and_write_post() callback
completing in target_complete_ok_work() before the first
can return.

Because current code depends on checking se_cmd->se_cmd_flags
after return from se_cmd->transport_complete_callback(),
this results in first stage having SCF_COMPARE_AND_WRITE_POST
set, which incorrectly falls through into second stage CAW
processing code, eventually triggering a NULL pointer
dereference due to use after free.

To address this bug, pass in a new *post_ret parameter into
se_cmd->transport_complete_callback(), and depend upon this
value instead of ->se_cmd_flags to determine when to return
or fall through into ->queue_status() code for CAW.

Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

This patch addresses a case where iscsi_target_do_tx_login_io()
fails sending the last login response PDU, after the RX/TX
threads have already been started.

The case centers around iscsi_target_rx_thread() not invoking
allow_signal(SIGINT) before the send_sig(SIGINT, ...) occurs
from the failure path, resulting in RX thread hanging
indefinately on iscsi_conn->rx_login_comp.

Note this bug is a regression introduced by:

  commit e5419865
  Author: Nicholas Bellinger <nab@linux-iscsi.org>
  Date:   Wed Jul 22 23:14:19 2015 -0700

      iscsi-target: Fix iscsit_start_kthreads failure OOPs

To address this bug, complete ->rx_login_complete for good
measure in the failure path, and immediately return from
RX thread context if connection state did not actually reach
full feature phase (TARG_CONN_STATE_LOGGED_IN).

Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Smatch complains about returning hard coded error codes, silence this
warning.

drivers/target/iscsi/iscsi_target_parameters.c:211
   iscsi_create_default_params() warn: returning -1 instead of -ENOMEM is sloppy
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

TCMU sets TRANSPORT_FLAG_PASSTHROUGH, so INQUIRY commands will not be
emulated by LIO but passed up to userspace. Therefore TCMU should not
set these, just like pscsi doesn't.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Reversed arguments meant that we were doing nothing for cmds whose deadline
had passed.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

On the ARM architecture, individual platforms select CONFIG_USE_OF if they
need it, but all device tree code is keyed off CONFIG_OF. When building
a platform without DT support and manually enabling CONFIG_OF, we now
get a number of build errors, e.g.

arch/arm/kernel/devtree.c: In function 'setup_machine_fdt':
arch/arm/kernel/devtree.c:215:19: error: implicit declaration of function 'early_init_dt_verify' [-Werror=implicit-function-declaration]

We could now try to separate the use case of booting from DT vs. the
case of using the dynamic implementation, but that seems more complicated
than it can gain us.

This simply changes the ARM Kconfig file to always enable OF_RESERVED_MEM
and OF_EARLY_FLATTREE when CONFIG_OF is enabled. These options add a little
extra code when we just want the dynamic OF implementation, but that seems
like a rather obscure case, and this version solves all CONFIG_OF related
randconfig regressions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0166dc11 ("of: make CONFIG_OF user selectable")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull PCI fixes from Bjorn Helgaas:
 "Here are a few fixes I'd like to have in v4.4: a generic one for sysfs
  and three for HiSilicon and DesignWare host controllers.

  Summary:

  NUMA:
   - Prevent out of bounds access in numa_node override (Mathias Krause)

  HiSilicon host bridge driver:
   - Fix deferred probing (Arnd Bergmann)

  Synopsys DesignWare host bridge driver:
   - Remove incorrect io_base assignment (Stanimir Varbanov)
   - Move align_resource function pointer to pci_host_bridge structure
     (Gabriele Paoloni)"

* tag 'pci-v4.4-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  ARM/PCI: Move align_resource function pointer to pci_host_bridge structure
  PCI: hisi: Fix deferred probing
  PCI: designware: Remove incorrect io_base assignment
  PCI: Prevent out of bounds access in numa_node override

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Stable patches:
   - Fix a NFSv4 callback identifier leak that was also causing client
     crashes
   - Fix NFSv4 callback decoding issues when incoming requests are
     truncated
   - Don't declare the attribute cache valid when we call
     nfs_update_inode with an empty attribute structure.
   - Resend LAYOUTGET when there is a race that changes the seqid

  Bugfixes:
   - Fix a number of issues with the NFSv4.2 CLONE ioctl()
   - Properly set NFS v4.2 NFSDBG_FACILITY
   - NFSv4 referrals are broken; Cleanup FATTR4_WORD0_FS_LOCATIONS after
     decoding success
   - Use sliding delay when LAYOUTGET gets NFS4ERR_DELAY
   - Ensure that attrcache is revalidated after a SETATTR"

* tag 'nfs-for-4.4-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  nfs4: resend LAYOUTGET when there is a race that changes the seqid
  nfs: if we have no valid attrs, then don't declare the attribute cache valid
  nfs: ensure that attrcache is revalidated after a SETATTR
  nfs4: limit callback decoding to received bytes
  nfs4: start callback_ident at idr 1
  nfs: use sliding delay when LAYOUTGET gets NFS4ERR_DELAY
  NFS4: Cleanup FATTR4_WORD0_FS_LOCATIONS after decoding success
  NFS: Properly set NFS v4.2 NFSDBG_FACILITY
  nfs: reduce the amount of ifdefs for v4.2 in nfs4file.c
  nfs: use btrfs ioctl defintions for clone
  nfs: allow intra-file CLONE
  nfs: offer native ioctls even if CONFIG_COMPAT is set
  nfs: pass on count for CLONE operations

Pull watchdog fixes from Wim Van Sebroeck:
 - a null pointer dereference fix for omap_wdt
 - some clock related fixes for pnx4008
 - an underflow fix in wdt_set_timeout() for w83977f_wdt
 - restart fix for tegra wdt
 - Kconfig change to support Freescale Layerscape platforms
 - fix for stopping the mtk_wdt watchdog

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: mtk_wdt: Use MODE_KEY when stopping the watchdog
  watchdog: Add support for Freescale Layerscape platforms
  watchdog: tegra: Stop watchdog first if restarting
  watchdog: w83977f_wdt: underflow in wdt_set_timeout()
  watchdog: pnx4008: make global wdt_clk static
  watchdog: pnx4008: fix warnings caused by enabling unprepared clock
  watchdog: omap_wdt: fix null pointer dereference

Pull btrfs fixes from Chris Mason:
 "This has Mark Fasheh's patches to fix quota accounting during subvol
  deletion, which we've been working on for a while now.  The patch is
  pretty small but it's a key fix.

  Otherwise it's a random assortment"

* 'for-linus-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: fix balance range usage filters in 4.4-rc
  btrfs: qgroup: account shared subtree during snapshot delete
  Btrfs: use btrfs_get_fs_root in resolve_indirect_ref
  btrfs: qgroup: fix quota disable during rescan
  Btrfs: fix race between cleaner kthread and space cache writeout
  Btrfs: fix scrub preventing unused block groups from being deleted
  Btrfs: fix race between scrub and block group deletion
  btrfs: fix rcu warning during device replace
  btrfs: Continue replace when set_block_ro failed
  btrfs: fix clashing number of the enhanced balance usage filter
  Btrfs: fix the number of transaction units needed to remove a block group
  Btrfs: use global reserve when deleting unused block group after ENOSPC
  Btrfs: tests: checking for NULL instead of IS_ERR()
  btrfs: fix signed overflows in btrfs_sync_file

Pull security layer fixes from James Morris:
 "A fix for SELinux policy processing (regression introduced by
  commit fa1aa143: "selinux: extended permissions for ioctls"), as
  well as a fix for the user-triggerable oops in the Keys code"

* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  KEYS: Fix handling of stored error in a negatively instantiated user key
  selinux: fix bug in conditional rules handling

Pull ARM SoC fixes from Arnd Bergmann:
 "There is a small backlog of at91 patches here, the most significant is
  the addition of some sama5d2 Xplained nodes that were waiting on an
  MFD include file to get merged through another tree.

  We normally try to sort those out before the merge window opens, but
  the maintainer wasn't aware of that here and I decided to merge the
  changes this time as an exception.

  On OMAP a series of audio changes for dra7 missed the merge window but
  turned out to be necessary to fix a boot time imprecise external abort
  error and to get audio working.

  The other changes are the usual simple changes, here is a list sorted
  by platform:

  at91:
	removal of a useless defconfig option
	removal of some legacy DT pieces
	use of the proper watchdog compatible string
	update of the MAINTAINERS entries for some Atmel drivers

  drivers/scpi:
	hide get_scpi_ops in module from built-in code

  imx:
	add missing .irq_set_type for i.MX GPC irq_chip.
	fix the wrong spi-num-chipselects settings for Vybrid DSPI devices.
	fix a merge error in Vybrid dts regarding to ADC device property

  keystone:
        fix the optional PDSP firmware loading
        fix linking RAM setup for QMs
        fix crash with clk_ignore_unused

  mediatek:
	Enable SCPSYS power domain driver by default

  mvebu:
	fix QNAP TS219 power-off in dts
	fix legacy get_irqnr_and_base for dove and orion5x

  omap:
	fix l4 related boot time errors for dm81xx
	use lockless cldm/pwrdm api in omap4_boot_secondary
	remove t410 abort handler to avoid hiding other critical errors
	mark cpuidle tracepoints as _rcuidle
	fix module alias for omap-ocp2scp

  pxa:
	palm: Fix typos in PWM lookup table code

  renesas:
	missing __initconst annotation for r8a7793_boards_compat_dt

  rockchip:
	disable mmc-tuning on the veyron-minnie board
	adding the init state for the over-temperature-protection

  zx:
	only build power domain code when CONFIG_PM=y"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
  ARM: OMAP4+: SMP: use lockless clkdm/pwrdm api in omap4_boot_secondary
  arm: omap2+: add missing HWMOD_NO_IDLEST in 81xx hwmod data
  ARM: orion5x: Fix legacy get_irqnr_and_base
  ARM: dove: Fix legacy get_irqnr_and_base
  soc: Mediatek: Enable SCPSYS power domain driver by default
  ARM: dts: vfxxx: Fix dspi[01] spi-num-chipselects.
  ARM: dts: keystone: k2l: fix kernel crash when clk_ignore_unused is not in bootargs
  soc: ti: knav_qmss_queue: Fix linking RAM setup for queue managers
  soc: ti: use request_firmware_direct() as acc firmware is optional
  ARM: imx: add platform irq type setting in gpc
  ARM: dts: vfxxx: Fix erroneous property in esdhc0 node
  ARM: shmobile: r8a7793: proper constness with __initconst
  scpi: hide get_scpi_ops in module from built-in code
  ARM: zx: only build power domain code when CONFIG_PM=y
  ARM: pxa: palm: Fix typos in PWM lookup table code
  ARM: dts: Kirkwood: Fix QNAP TS219 power-off
  ARM: dts: rockchip: Add OTP gpio pinctrl to rk3288 tsadc node
  ARM: dts: rockchip: temporarily remove emmc hs200 speed from rk3288 minnie
  MAINTAINERS: Atmel drivers: change NAND and ISI entries
  ARM: at91/dt: sama5d2 Xplained: add several devices
  ...

Pull more power management and ACPI fixes from Rafael Wysocki:
 "These fix one recent regression (cpufreq core), fix up two features
  added recently (ACPI CPPC support, SCPI support in the arm_big_little
  cpufreq driver) and fix three older bugs in the intel_pstate driver.

  Specifics:

   - Fix a recent regression in the cpufreq core causing it to fail to
     clean up sysfs directories properly on cpufreq driver removal
     (Viresh Kumar).

   - Fix a build problem in the SCPI support code recently added to the
     arm_big_little cpufreq driver (Punit Agrawal).

   - Fix up the recently added CPPC cpufreq frontend to process the CPU
     coordination information provided by the platform firmware
     correctly (Ashwin Chaugule).

   - Fix the intel_pstate driver to behave as intended when switched
     over to the "performance" mode via sysfs if hardware-driven P-state
     selection (HWP) is enabled (Alexandra Yates).

   - Fix two rounding errors in the intel_pstate driver that sometimes
     cause it to use lower P-states than requested (Prarit Bhargava)"

* tag 'pm+acpi-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  intel_pstate: Fix "performance" mode behavior with HWP enabled
  cpufreq: SCPI: Depend on SCPI clk driver
  cpufreq: intel_pstate: Fix limits->max_perf rounding error
  cpufreq: intel_pstate: Fix limits->max_policy_pct rounding error
  cpufreq: Always remove sysfs cpuX/cpufreq link on ->remove_dev()
  cpufreq: CPPC: Initialize and check CPUFreq CPU co-ord type correctly

Ben Skeggs wrote:
A couple of regression fixes, some more boards whitelisted for a hw bug
workaround, gr/ucode fixes for hangs a user is seeing.

The changes look larger than they actually are due to the ucode binaries
(*.fucN.h) being regenerated.

* 'linux-4.4' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
  drm/nouveau/volt/pwm/gk104: fix an off-by-one resulting in the voltage not being set
  drm/nouveau/nvif: allow userspace access to its own client object
  drm/nouveau/gr/gf100-: fix oops when calling zbc methods
  drm/nouveau/gr/gf117-: assume no PPC if NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK is zero
  drm/nouveau/gr/gf117-: read NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK from correct GPC
  drm/nouveau/gr/gf100-: split out per-gpc address calculation macro
  drm/nouveau/bios: return actual size of the buffer retrieved via _ROM
  drm/nouveau/instmem: protect instobj list with a spinlock
  drm/nouveau/pci: enable c800 magic for some unknown Samsung laptop
  drm/nouveau/pci: enable c800 magic for Clevo P157SM

Pull sound fixes from Takashi Iwai:
 "Here are no big surprises but just all small fixes, mostly
  device-specific quirks for HD-audio and USB-audio:

   - Fix for detection of FireWire DICE Loud devices
   - Intel Broxton HDMI/DP PCI IDs and relevant quirks
   - Noise fixes: Dell XPS13 2015 model, Dell Latitude E6440, Gigabyte
     Z170X mobo
   - Fix the headphone mixer assignment on HP laptops for PulseAudio
   - USB-MIDI fixes for Medeli DD305 and CH345
   - Apply fixup for Acer Aspire One Cloudbook 14"

* tag 'sound-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix noise on Gigabyte Z170X mobo
  ALSA: hda - Fix headphone noise after Dell XPS 13 resume back from S3
  ALSA: hda - Apply HP headphone fixups more generically
  ALSA: hda - Add fixup for Acer Aspire One Cloudbook 14
  ALSA: hda - apply SKL display power request/release patch to BXT
  ALSA: hda - add PCI IDs for Intel Broxton
  ALSA: usb-audio: work around CH345 input SysEx corruption
  ALSA: usb-audio: prevent CH345 multiport output SysEx corruption
  ALSA: usb-audio: add packet size quirk for the Medeli DD305
  ALSA: dice: fix detection of Loud devices
  ALSA: hda - Fix noise on Dell Latitude E6440

Pull arm64 fixes from Catalin Marinas:

 - Build fix when !CONFIG_UID16 (the patch is touching generic files but
   it only affects arm64 builds; submitted by Arnd Bergmann)

 - EFI fixes to deal with early_memremap() returning NULL and correctly
   mapping run-time regions

 - Fix CPUID register extraction of unsigned fields (not to be
   sign-extended)

 - ASID allocator fix to deal with long-running tasks over multiple
   generation roll-overs

 - Revert support for marking page ranges as contiguous PTEs (it leads
   to TLB conflicts and requires additional non-trivial kernel changes)

 - Proper early_alloc() failure check

 - Disable KASan for 48-bit VA and 16KB page configuration (the pgd is
   larger than the KASan shadow memory)

 - Update the fault_info table (original descriptions based on early
   engineering spec)

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: efi: fix initcall return values
  arm64: efi: deal with NULL return value of early_memremap()
  arm64: debug: Treat the BRPs/WRPs as unsigned
  arm64: cpufeature: Track unsigned fields
  arm64: cpufeature: Add helpers for extracting unsigned values
  Revert "arm64: Mark kernel page ranges contiguous"
  arm64: mm: keep reserved ASIDs in sync with mm after multiple rollovers
  arm64: KASAN depends on !(ARM64_16K_PAGES && ARM64_VA_BITS_48)
  arm64: efi: correctly map runtime regions
  arm64: mm: fix fault_info table xFSC decoding
  arm64: fix building without CONFIG_UID16
  arm64: early_alloc: Fix check for allocation failure

Pull nios2 fix from Ley Foon Tan:
 "nios2: fix cache coherency"

* tag 'nios2-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
  nios2: fix cache coherency

GCC 4.1 and newer remove empty loops.  This becomes a problem when delay
loops get removed.  Fixed by rewriting to user the proper Linux interface
for such delays.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: John Crispin <blogic@openwrt.org>

Pull ARC fixes from Vineet Gupta:
 - Fix for perf callgraph unwinding causing RCU stalls
 - Fix to enable Linux to run on non-default Interrupt priority 0
 - Removal of pointless SYNC from __switch_to()

* tag 'arc-4.4-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: dw2 unwind: Remove falllback linear search thru FDE entries
  ARC: remove SYNC from __switch_to()
  ARCv2: Use the default irq priority for idle sleep
  ARC: Abstract out ISA specific SLEEP args
  ARC: comments update
  ARC: switch to arc-linux- CROSS_COMPILE prefix across all configs