Let's see if anybody even notices.  I doubt anybody uses this, and it
does expose addresses that should be randomized, so let's just remove
the code.  It's old and traditional, and it used to be cute, but we
should have removed this long ago.

If it turns out anybody notices and this breaks something, we'll have to
revert this, and maybe we'll end up using other approaches instead
(using %pK or similar).  But removing unnecessary code is always the
preferred option.
Noted-by: Emrah Demir <ed@abdsec.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull rdma fixes from Doug Ledford:
 "I'm back from PTO.  These issues cropped up while I was gone and are
  simple fixes.  I'll have more after I've caught up, but I wanted to
  get these in quick.

  Two minor fixes for 4.6-rc2:

   - Fix mlx5 build error when on demand paging is not enabled

   - Fix possible uninit variable in new i40iw driver"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  i40iw: avoid potential uninitialized variable use
  IB/mlx5: fix VFs callback function prototypes

gcc finds that the i40iw_make_cm_node() function in the recently added
i40iw driver uses an uninitilized variable as an index into an array
if CONFIG_IPV6 is disabled and the driver uses IPv6 mode:

drivers/infiniband/hw/i40iw/i40iw_cm.c: In function 'i40iw_make_cm_node':
drivers/infiniband/hw/i40iw/i40iw_cm.c:2206:52: error: 'arpindex' may be used uninitialized in this function [-Werror=maybe-uninitialized]
  ether_addr_copy(cm_node->rem_mac, iwdev->arp_table[arpindex].mac_addr);

As far as I can tell, this code path can not be used because the ipv4
variable is always set with CONFIG_IPV6 is disabled, but it's better
to be sure and prevent the undefined behavior, as well as shut up
that warning in a proper way.

This adds an 'else' clause for the case we get the warning about,
causing the function to return an error in a controlled way.
To avoid adding extra mess with combined io()/#ifdef clauses,
I'm also converting the existing #ifdef into a more readable
if(IS_ENABLED()) check.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f27b4746 ("i40iw: add connection management code")
Acked-by: Mustafa Ismail <Mustafa.ismail@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The previous patch that added a couple of callback functions put
the declarations inside of an #ifdef CONFIG_INFINIBAND_ON_DEMAND_PAGING,
which causes the build to fail if that option is disabled:

drivers/infiniband/hw/mlx5/main.c: In function 'mlx5_ib_add':
drivers/infiniband/hw/mlx5/main.c:2358:31: error: 'mlx5_ib_get_vf_config' undeclared (first use in this function)

This moves the four declarations below the #ifdef section so they
are always available.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: eff901d3 ("IB/mlx5: Implement callbacks for manipulating VFs")
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Pull KVM fixes from Paolo Bonzini:
 "Miscellaneous bugfixes.

  The ARM and s390 fixes are for new regressions from the merge window,
  others are usual stable material"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  compiler-gcc: disable -ftracer for __noclone functions
  kvm: x86: make lapic hrtimer pinned
  s390/mm/kvm: fix mis-merge in gmap handling
  kvm: set page dirty only if page has been writable
  KVM: x86: reduce default value of halt_poll_ns parameter
  KVM: Hyper-V: do not do hypercall userspace exits if SynIC is disabled
  KVM: x86: Inject pending interrupt even if pending nmi exist
  arm64: KVM: Register CPU notifiers when the kernel runs at HYP
  arm64: kvm: 4.6-rc1: Fix VTCR_EL2 VS setting

Pull spi fixes from Mark Brown:
 "A couple of driver specific fixes here that came in since the merge
  window plus one core fix for locking in cases where a client driver
  grabs a lock on the whole bus for an extended series of operations
  that was introduced by the changes to support accelerated flash
  operations"

* tag 'spi-fix-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: rockchip: fix probe deferral handling
  spi: omap2-mcspi: fix dma transfer for vmalloced buffer
  spi: fix possible deadlock between internal bus locks and bus_lock_flag
  spi: imx: Fix possible NULL pointer deref
  spi: imx: only do necessary changes to ECSPIx_CONFIGREG
  spi: rockchip: Spelling s/divsor/divisor/

Pull pin control fixes from Linus Walleij:
 "Here is a set of pin control fixes for the v4.6 series.

  A bit bigger than what I hoped for, but all fixes are confined to
  drivers, a few of them also targeted to stable.

  Summary:

   - On Super-H PFC (Renesas) controllers: only use dummies on legacy
     systems.  This fixes a serious ethernet regression on a Renesas
     board.
   - Pistachio: Fix errors in the pin table.
   - Allwinner SunXi: fix the external interrupts to work.
   - Intel: fix so the high level interrupts start working, and fix a
     spurious interrupt issue.
   - Qualcomm ipq4019: fix the number of GPIOs provided (bump to 100),
     correct register offsets and handle GPIO mode properly.
   - Revert the revert on the revert so that Xway has a .to_irq()
     callback again.
   - Minor fixes to errorpaths and debug info.
   - A MAINTAINERS update"

* tag 'pinctrl-v4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  Revert "Revert "pinctrl: lantiq: Implement gpio_chip.to_irq""
  pinctrl: qcom: ipq4019: fix register offsets
  pinctrl: qcom: ipq4019: fix the function enum for gpio mode
  pinctrl: qcom: ipq4019: set ngpios to correct value
  pinctrl: nomadik: fix pull debug print inversion
  MAINTAINERS: pinctrl: samsung: Add two new maintainers
  pinctrl: intel: implement gpio_irq_enable
  pinctrl: intel: make the high level interrupt working
  pinctrl: freescale: imx: fix bogus check of of_iomap() return value
  pinctrl: sunxi: Fix A33 external interrupts not working
  pinctrl: pistachio: fix mfio84-89 function description and pinmux.
  pinctrl: sh-pfc: only use dummy states for non-DT platforms

Pull media fixes from Mauro Carvalho Chehab:
 "Some bug fixes on au0828 and snd-usb-audio:

   - the au0828+snd-usb-audio MC patch broke several things and produced
     some race conditions.  Better to revert the patches, and re-work on
     them for a next version

   - fix a regression at tuner disable links logic

   - properly handle dev_state as a bitmask"

* tag 'media/v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] Revert "[media] media: au0828 change to use Managed Media Controller API"
  [media] Revert "[media] sound/usb: Use Media Controller API to share media resources"
  [media] au0828: Fix dev_state handling
  [media] au0828: fix au0828_v4l2_close() dev_state race condition
  [media] media: au0828 fix to clear enable/disable/change source handlers
  [media] v4l2-mc: cleanup a warning
  [media] au0828: disable tuner links and cache tuner/decoder

-ftracer can duplicate asm blocks causing compilation to fail in
noclone functions.  For example, KVM declares a global variable
in an asm like

    asm("2: ... \n
         .pushsection data \n
         .global vmx_return \n
         vmx_return: .long 2b");

and -ftracer causes a double declaration.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: stable@vger.kernel.org
Cc: kvm@vger.kernel.org
Reported-by: Linda Walsh <lkml@tlinx.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

When a vCPU runs on a nohz_full core, the hrtimer used by
the lapic emulation code can be migrated to another core.
When this happens, it's possible to observe milisecond
latency when delivering timer IRQs to KVM guests.

The huge latency is mainly due to the fact that
apic_timer_fn() expects to run during a kvm exit. It
sets KVM_REQ_PENDING_TIMER and let it be handled on kvm
entry. However, if the timer fires on a different core,
we have to wait until the next kvm exit for the guest
to see KVM_REQ_PENDING_TIMER set.

This problem became visible after commit 9642d18e. This
commit changed the timer migration code to always attempt
to migrate timers away from nohz_full cores. While it's
discussable if this is correct/desirable (I don't think
it is), it's clear that the lapic emulation code has
a requirement on firing the hrtimer in the same core
where it was started. This is achieved by making the
hrtimer pinned.

Lastly, note that KVM has code to migrate timers when a
vCPU is scheduled to run in different core. However, this
forced migration may fail. When this happens, we can have
the same problem. If we want 100% correctness, we'll have
to modify apic_timer_fn() to cause a kvm exit when it runs
on a different core than the vCPU. Not sure if this is
possible.

Here's a reproducer for the issue being fixed:

 1. Set all cores but core0 to be nohz_full cores
 2. Start a guest with a single vCPU
 3. Trace apic_timer_fn() and kvm_inject_apic_timer_irqs()

You'll see that apic_timer_fn() will run in core0 while
kvm_inject_apic_timer_irqs() runs in a different core. If
you get both on core0, try running a program that takes 100%
of the CPU and pin it to core0 to force the vCPU out.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

commit 1e133ab2 ("s390/mm: split arch/s390/mm/pgtable.c") dropped
some changes from commit a3a92c31 ("KVM: s390: fix mismatch
between user and in-kernel guest limit") - this breaks KVM for some
memory sizes (kvm-s390: failed to commit memory region) like
exactly 2GB.

Cc: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Merge tag 'linux-kselftest-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest fixes from Shuah Khan:
 "This update for Kselftest contains seccomp fixes"

* tag 'linux-kselftest-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftest/seccomp: Fix the seccomp(2) signature
  selftest/seccomp: Fix the flag name SECCOMP_FILTER_FLAG_TSYNC

Pull MIPS fixes from Ralf Baechle:
 "This is the first round of MIPS fixes for 4.6:

   - Fix spelling mistakes all over arch/mips
   - Provide __bswapsi2 so XZ kernel compression will build with older GCC
   - ATH79 clock fixes.
   - Fix clock-rated copy-paste erros in ATH79 DTS.
   - Fix gisb-arb compatible string for 7435 BMIPS
   - Enable NAND and UBIFS support in CI20.
   - Fix BUG() assertion caused by inapropriate smp_processor_id() use.
   - Fix exception handling issues for the sake of debuggers
   - Fix the last remaining instance of irq_to_gpio in the db1xxx_ss PCMCIA code
   - Fix MSA unaligned load failures
   - Panic if kernel is configured for a not TLB-supported page size
   - Bail out on unsupported relocs in modules.
   - Partial fix for Qemu breakage after recent IPI rewrite
   - Wire up the preadv2 and pwrite2 syscalls
   - Fix the ar724x clock calculation"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: traps.c: Verify the ISA for microMIPS RDHWR emulation
  MIPS: BMIPS: Fix gisb-arb compatible string for 7435
  MIPS: Bail on unsupported module relocs
  MIPS: dts: qca: ar9132_tl_wr1043nd_v1.dts: use "ref" for reference clock name
  MIPS: ath79: Fix the ar913x reference clock rate
  MIPS: ath79: Fix the ar724x clock calculation
  dt-bindings: clock: qca,ath79-pll: fix copy-paste typos
  MIPS: traps: Correct the SIGTRAP debug ABI in `do_watch' and `do_trap_or_bp'
  FIRMWARE: Broadcom: Fix grammar of warning messages in bcm47xx_sprom.c.
  MIPS: ci20: Enable NAND and UBIFS support in defconfig.
  MIPS: Fix misspellings in comments.
  MIPS: tlb-r4k: panic if the MMU doesn't support PAGE_SIZE
  MIPS: zboot: Remove copied source files on clean
  MIPS: zboot: Fix the build with XZ compression on older GCC versions
  MIPS: Wire up preadv2 and pwrite2 syscalls.
  MIPS: cpu_name_string: Use raw_smp_processor_id().
  pcmcia: db1xxx_ss: fix last irq_to_gpio user
  MIPS: Fix MSA ld unaligned failure cases
  MIPS: Fix broken malta qemu

Pull xen fixes from David Vrabel:
 "Regression and bug fixes for 4.6-rc2:

   - safely migrate event channels between CPUs
   - fix CPU hotplug
   - maintainer changes"

* tag 'for-linus-4.6-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  MAINTAINERS: xen: Konrad to step down and Juergen to pick up
  xen/events: Mask a moving irq
  Xen on ARM and ARM64: update MAINTAINERS info
  xen/x86: Call cpu_startup_entry(CPUHP_AP_ONLINE_IDLE) from xen_play_dead()
  xen/apic: Provide Xen-specific version of cpu_present_to_apicid APIC op

Pull quota fixes from Jan Kara:
 "Fixes for oopses when the new quotactl gets used with quotas disabled"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  ocfs2: Fix Q_GETNEXTQUOTA for filesystem without quotas
  quota: Handle Q_GETNEXTQUOTA when quota is disabled

Pull f2fs fixes from Jaegeuk Kim.

* tag 'f2fs-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs:
  f2fs: retrieve IO write stat from the right place
  f2fs crypto: fix corrupted symlink in encrypted case
  f2fs: cover large section in sanity check of super

In commit e4570897 ("drm/dp-helper: Move the legacy helpers to
gma500") the legacy i2c helpers were moved to the only remaining user of
them, the gma500 driver.  Together with that move, i2c_dp_aux_add_bus()
was marked deprecated and started warning about its remaining use.

It's now been a year and a half of annoying warning, and apparently
nobody cares enough about gma500 to try to move it along to the more
modern models.

Get rid of the warning - if even the gma500 people don't care enough,
then they should certainly not spam other innocent developers with a
warning that might hide other, much more real issues.

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge PAGE_CACHE_SIZE removal patches from Kirill Shutemov:
 "PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
  ago with promise that one day it will be possible to implement page
  cache with bigger chunks than PAGE_SIZE.

  This promise never materialized.  And unlikely will.

  Let's stop pretending that pages in page cache are special.  They are
  not.

  The first patch with most changes has been done with coccinelle.  The
  second is manual fixups on top.

  The third patch removes macros definition"

[ I was planning to apply this just before rc2, but then I spaced out,
  so here it is right _after_ rc2 instead.

  As Kirill suggested as a possibility, I could have decided to only
  merge the first two patches, and leave the old interfaces for
  compatibility, but I'd rather get it all done and any out-of-tree
  modules and patches can trivially do the converstion while still also
  working with older kernels, so there is little reason to try to
  maintain the redundant legacy model.    - Linus ]

* PAGE_CACHE_SIZE-removal:
  mm: drop PAGE_CACHE_* and page_cache_{get,release} definition
  mm, fs: remove remaining PAGE_CACHE_* and page_cache_{get,release} usage
  mm, fs: get rid of PAGE_CACHE_* and page_cache_{get,release} macros

All users gone.  We can remove these macros.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Mostly direct substitution with occasional adjustment or removing
outdated comments.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.

This promise never materialized.  And unlikely will.

We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE.  And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.

Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.

Let's stop pretending that pages in page cache are special.  They are
not.

The changes are pretty straight-forward:

 - <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;

 - <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;

 - PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};

 - page_cache_get() -> get_page();

 - page_cache_release() -> put_page();

This patch contains automated changes generated with coccinelle using
script below.  For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.

The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.

There are few places in the code where coccinelle didn't reach.  I'll
fix them manually in a separate patch.  Comments and documentation also
will be addressed with the separate patch.

virtual patch

@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E

@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E

@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT

@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE

@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK

@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)

@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)

@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Make sure it's the microMIPS rather than MIPS16 ISA before emulating
microMIPS RDHWR.  Mostly needed as an optimisation for configurations
where `cpu_has_mmips' is hardcoded to 0 and also a good measure in case
we add further microMIPS instructions to emulate in the future, as the
corresponding MIPS16 encoding is ADDIUSP, not supposed to trap.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12282/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The SUN GISB arbiter was added with the wrong compatible string, leading to
using the wrong register layout, use the correct compatible string for this
chip: brcm,bcm7435-gisb-arb.

Fixes: 8394968be4c7 ("MIPS: BMIPS: Add BCM7435 dtsi")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: blogic@openwrt.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Cc: jaedon.shin@gmail.com
Cc: pgynther@google.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12285/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

I've lately been concentrating on other projects and haven't been
doing much of Xen core maintainership for the last year.

I am quite thrilled that Juergen is willing to help out!

P.S.
I am still the maintainer of Xen-SWIOTLB, Xen PCI-[front|backend],
and co-maintainer of Xen block-[front|backend]; amongst others.
Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Moving an unmasked irq may result in irq handler being invoked on both
source and target CPUs.

With 2-level this can happen as follows:

On source CPU:
        evtchn_2l_handle_events() ->
            generic_handle_irq() ->
                handle_edge_irq() ->
                   eoi_pirq():
                       irq_move_irq(data);

                       /***** WE ARE HERE *****/

                       if (VALID_EVTCHN(evtchn))
                           clear_evtchn(evtchn);

If at this moment target processor is handling an unrelated event in
evtchn_2l_handle_events()'s loop it may pick up our event since target's
cpu_evtchn_mask claims that this event belongs to it *and* the event is
unmasked and still pending. At the same time, source CPU will continue
executing its own handle_edge_irq().

With FIFO interrupt the scenario is similar: irq_move_irq() may result
in a EVTCHNOP_unmask hypercall which, in turn, may make the event
pending on the target CPU.

We can avoid this situation by moving and clearing the event while
keeping event masked.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Pull perf fixes from Ingo Molnar:
 "Misc kernel side fixes:

   - fix event leak
   - fix AMD PMU driver bug
   - fix core event handling bug
   - fix build bug on certain randconfigs

  Plus misc tooling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/amd/ibs: Fix pmu::stop() nesting
  perf/core: Don't leak event in the syscall error path
  perf/core: Fix time tracking bug with multiplexing
  perf jit: genelf makes assumptions about endian
  perf hists: Fix determination of a callchain node's childlessness
  perf tools: Add missing initialization of perf_sample.cpumode in synthesized samples
  perf tools: Fix build break on powerpc
  perf/x86: Move events_sysfs_show() outside CPU_SUP_INTEL
  perf bench: Fix detached tarball building due to missing 'perf bench memcpy' headers
  perf tests: Fix tarpkg build test error output redirection

Pull core kernel fixes from Ingo Molnar:
 "This contains the nohz/atomic cleanup/fix for the fetch_or() ugliness
  you noted during the original nohz pull request, plus there's also
  misc fixes:

   - fix liblockdep build bug
   - fix uapi header build bug
   - print more lockdep hash collision info to help debug recent reports
     of hash collisions
   - update MAINTAINERS email address"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  MAINTAINERS: Update my email address
  locking/lockdep: Print chain_key collision information
  uapi/linux/stddef.h: Provide __always_inline to userspace headers
  tools/lib/lockdep: Fix unsupported 'basename -s' in run_tests.sh
  locking/atomic, sched: Unexport fetch_or()
  timers/nohz: Convert tick dependency mask to atomic_t
  locking/atomic: Introduce atomic_fetch_or()

Commit 840f5b05 ("media: au0828 disable tuner to demod link in
au0828_media_device_register()") removed all uses of the 'dtv_demod',
but left the variable itself around.

Remove it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull x86 fixes from Thomas Gleixner:
 "This lot contains:

   - Some fixups for the fallout of the topology consolidation which
     unearthed AMD/Intel inconsistencies
   - Documentation for the x86 topology management
   - Support for AMD advanced power management bits
   - Two simple cleanups removing duplicated code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Add advanced power management bits
  x86/thread_info: Merge two !__ASSEMBLY__ sections
  x86/cpufreq: Remove duplicated TDP MSR macro definitions
  x86/Documentation: Start documenting x86 topology
  x86/cpu: Get rid of compute_unit_id
  perf/x86/amd: Cleanup Fam10h NB event constraints
  x86/topology: Fix AMD core count

When an unsupported reloc is encountered in a module, we currently
blindly branch to whatever would be at its entry in the reloc handler
function pointer arrays. This may be NULL, or if the unsupported reloc
has a type greater than that of the supported reloc with the highest
type then we'll dereference some value after the function pointer array
& branch to that. The result is at best a kernel oops.

Fix this by checking that the reloc type has an entry in the function
pointer array (ie. is less than the number of items in the array) and
that the handler is non-NULL, returning an error code to fail the module
load if no handler is found.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12432/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Current ath79 clock.c code does not read reference clock and
pll setup from devicetree. The ar724x_clocks_init() function
recreates the clocks from scratch so devicetree clock
information is dropped. After adding the code which picked up
reference clock from devicetree I have found
that kernel does not boot anymore. The SPI and UART drivers
can't get clk; here are the bootlog error messages:

    of_serial: probe of 18020000.uart failed with error -22
    ath79-spi: probe of 1f000000.spi failed with error -22

The problem is that clock code assumes that reference clock
name is "ref" but current dts-file uses another name: "oscillator".

This patch fixes the problem by changing external oscillator
dt node name to "ref".

Please note that there is an alternative solution for the problem:

    > --- a/arch/mips/boot/dts/qca/ar9132_tl_wr1043nd_v1.dts
    > +++ b/arch/mips/boot/dts/qca/ar9132_tl_wr1043nd_v1.dts
    > @@ -16,6 +16,7 @@
    >
    >         extosc: oscillator {
    >                 compatible = "fixed-clock";
    > +               clock-output-names = "ref";
    >                 #clock-cells = <0>;
    >                 clock-frequency = <40000000>;
    >         };
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Alban Bedel <albeu@free.fr>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12874/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The reference clock on ar913x is at 40MHz and not 5MHz. The current
implementation use the wrong reference rate because it doesn't take
the PLL divider in account. But if we fix the code to use the divider
it becomes identical with the implementation for ar724x, so just drop
the broken ar913x implementation.
Signed-off-by: Alban Bedel <albeu@free.fr>
Tested-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12871/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

According to the AR7242 datasheet section 2.8, AR724X CPUs use a 40MHz
input clock as the REF_CLK instead of 5MHz.

The correct CPU PLL calculation procedure is as follows:
CPU_PLL = (FB * REF_CLK) / REF_DIV / 2.

This patch is compatible with the current calculation procedure with
default FB and REF_DIV values.

Tested on AR7240, AR7241 and AR7242.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Alban Bedel <albeu@free.fr> (Fixed the commit log message)
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12870/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12869/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Follow our own rules set in <asm/siginfo.h> for SIGTRAP signals issued
from `do_watch' and `do_trap_or_bp' by setting the signal code to
TRAP_HWBKPT and TRAP_BRKPT respectively, for Watch exceptions and for
those Breakpoint exceptions whose originating BREAK instruction's code
does not have a special meaning.  Keep Trap exceptions unaffected as
these are not debug events.

No existing user software is expected to examine signal codes for these
signals as SI_KERNEL has been always used here.  This change makes the
MIPS port more like other Linux ports, which reduces the complexity and
provides for performance improvement in GDB.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Luis Machado <lgustavo@codesourcery.com>
Cc: linux-mips@linux-mips.org
Cc: gdb@sourceware.org
Patchwork: https://patchwork.linux-mips.org/patch/12758/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>