Add lpspi0 lpspi1 lpspi2 lpspi3 node at common dma subsystem.
Change irq number for 8dxl.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable flexspi0 at imx8dxl_evk boards dts.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add flexspi0 node at common lsio subsystem.
Change flexspi0 irq number for imx8dxl.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable adc0 at imx8dxl_evk boards dts.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add adc0 and adc1 node at imx8 common dma subsystem.
imx8dxl have only adc0. Change irq number for adc0.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add gpio pins present on new board revision:
 * LTE modem support (imx8mm-gw7902 only)
  - lte_pwr#
  - lte_rst
  - lte_int
 * M2 power enable
  - m2_pwr_en
 * off-board 4.0V supply
  - vdd_4p0_en
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There is no such always-enabled property supported by gpio-watchdog
driver or described in its bindings, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix the following dtbs_check warning on all of i.MX8M variants:
"
opp-table: Unevaluated properties are not allowed ('opp-25M', 'opp-100M', 'opp-750M' were unexpected)
"
Using the following command:
"
$ sed -i '/opp-[0-9]\+M/ s@M {@000000 {@' arch/arm64/boot/dts/freescale/imx8m*
"

The Documentation/devicetree/bindings/opp/opp-v2-base.yaml expects the OPP
subnode names to be full frequency listings in Hz without unit suffixes.
Only the i.MX8M DTs are affected per "git grep 'opp-[0-9]\+M'", so fix them.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The DT bindings checker is confused by the -gpio node suffix,
drop it to fix the following warning:
"
imx8mm-data-modul-edm-sbc.dtb: /: watchdog-gpio: {'pinctrl-names': ['default'], 'pinctrl-0': [[104]], 'compatible': ['linux,wdt-gpio'], 'always-enabled': True, 'gpios': [[45, 8, 0]], 'hw_algo': ['level'], 'hw_margin_ms': [[1500]], 'status': ['disabled']} is not of type 'array'
"
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As both Dahlia and the Verdin Development Board have on-carrier
permanently attached USB hubs mark Verdin USB_2 as such.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add GPIO USB-B connector (gpio-usb-b-connector) functionality using
Verdin USB_1_ID.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Disable port power control on Verdin USB_1/2 as we use regular
fixed-regulators with Verdin USB_1/2_EN as enable GPIOs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Verdin USB_1 over-current detection functionality via Verdin
USB_1_OC# (SODIMM 157) being active-low and removing its previous
gpio_hog3 mapping.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The disable-over-current property is only applicable for the
ci-hdrc-usb2 and dwc2 drivers while the i.MX 8M Plus integrates dwc3
IP. Therefore remove this property which does not really serve any
purpose here.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As we are using two fixed regulators for Verdin USB_1_EN (SODIMM 155)
and Verdin USB_2_EN (SODIMM 185), those should be muxed as GPIOs rather
than OTG_PWR.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds the support for optional PWM fan 422J/2HP.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add PCIe support on TQMa8MPxL module on MBa8MPxL mainboard.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX8MP DHCOM SoM does contain muRata 2AE WiFi+BT chip, bind the
bluetooth to UART2 using btbcm and hci_bcm drivers. Use PLL3 to drive
UART2 clock divided down to 64 MHz to obtain suitable block clock for
exact 4 Mbdps, which is the maximum supported baud rate by the muRata
2AE BT UART.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable usb phy to be wakeup source to support system wakeup
from usb.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX8MP ECSPI is derived from i.MX6UL, so update compatible
Add assigned-clocks settings
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add tpm[2,4-6] node
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add more lpspi nodes which exist in i.MX93
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

gpio driver need these gpio alises to config the gpio base.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add MU clock for mailbox usage
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There is no internal '/3' divider in i.MX93 sysctr, so need this
property.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The mii_select node is used to determine the fec1's interface
type. Using "enable-active-high" property to configure the
interface type as "RMII". Deleting the property as "RGMII".
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

add scu_gpio node in system-controller.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use predefined colors and function rather than making up a random label.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

We can use PWM instead of just GPIO allowing us to control brightness.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There are two chipidea usb controller in 8dxl.
Add usb node at common connect subsystem.
Enable two usb at imx8dxl_evk boards dts.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PHY clock output is not connected to anything, drop the clock output
configuration. This way, the PHY does not generate output clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PMIC is the 32 kHz clock source for the RTC_XTALI input of the SoC
on this system. The RTC_XTALI input is used to supply 32 kHz clock to
the SVNS RTC per "i.MX 8M Mini Applications Processor Reference Manual,
Rev. 3, 11/2020" page 759 "The 32KHz XTAL module uses a different IP and
it is used as the clock source for the RTC, located in the SNVS." The
PMIC has its own dedicated 32 kHz XTAL on input.

Model the connection in DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The CCM ANALOG module is used for generate PLLs, align the node
with DT bindings
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Slight improvement of pcie node to be more in-line with what we add on
the Verdin iMX8M Plus.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Rename sn65dsi83 to sn65dsi84 as that is the exact chip used on the
Verdin DSI to LVDS Adapter.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Improve include notation. Usually only dtsi files from the same location
are included with an absolute path in quotes. Others should use a
relative path enclosed in angle brackets.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Improve include notation. Usually only dtsi files from the same location
are included with an absolute path in quotes. Others should use a
relative path enclosed in angle brackets.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the InnoComm i.MX8MM based WB15 SoM and its EVK. The WB15 is a
half credit card sized board featuring:

- i.MX8MM CPU
- LPDDR4, 1GiB
- eMMC, 8GiB
- 1Gb Ethernet RGMII interface
- WiFi 802.11 a/b/g/n/ac, Bluetooth 4.2
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add I2C GPIO bus recovery support by adding scl-gpios and sda-gpios for the
various I2C busses on Gateworks Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fixes the warnings:
at24 0-0053: supply vcc not found, using dummy regulator
at24 0-0057: supply vcc not found, using dummy regulator
at24 1-0057: supply vcc not found, using dummy regulator
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>