Currently, on a new link creation or when 'remote' address parameter
is updated, an MTU is not changed and always equals 1500. When a lower
device has a larger MTU, it might not be efficient, e.g. for UDP, and
requires the manual MTU adjustments to match the MTU of the lower
device.

This patch tries to automate this process, finds a lower device using
the 'remote' address parameter, then uses its MTU to tune GENEVE's MTU:
  * on a new link creation
  * when 'remote' parameter is changed

Also with this patch, the MTU from a user, on a new link creation, is
passed to geneve_change_mtu() where it is verified, and MTU adjustments
with a lower device is skipped in that case. Prior that change, it was
possible to set the invalid MTU values on a new link creation.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

geneve_change_mtu() will be used not only as ndo_change_mtu() callback,
but also to verify a user specified MTU on a new link creation in the
next patch.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use ETH_HLEN instead and introduce two new macros: GENEVE_IPV4_HLEN
and GENEVE_IPV6_HLEN that include Ethernet header length, corresponded
IP header length and GENEVE_BASE_HLEN.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Account for operational state when determining port linkup state,
as per Documentation/networking/operstates.txt.
Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

GhantaKrishnamurthy MohanKrishna says:

====================
tipc: Confgiuration of MTU for media UDP

Systematic measurements have shown that an emulated MTU of 14k for
UDP bearers is the optimal value for maximal throughput. Accordingly,
the default MTU of UDP bearers is changed to 14k.

We also provide users with a fallback option from this value,
by providing support to configure MTU for UDP bearers. The following
options are introduced which are symmetrical to the design of
confguring link tolerance.

- Configure media with new MTU value, which will take effect on
links going up after the moment it was configured. Alternatively,
the bearer has to be disabled and re-enabled, for existing links to
reflect the configured value.

- Configure bearer with new MTU value, which take effect on
running links dynamically.

Please note:
- User has to change MTU at both endpoints, otherwise the link
will fall back to smallest MTU after a reset.
- Failover from a link with higher MTU to a link with lower MTU
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, we have option to configure MTU of UDP media. The configured
MTU takes effect on the links going up after that moment. I.e, a user
has to reset bearer to have new value applied across its links. This is
confusing and disturbing on a running cluster.

We now introduce the functionality to change the default UDP bearer MTU
in struct tipc_bearer. Additionally, the links are updated dynamically,
without any need for a reset, when bearer value is changed. We leverage
the existing per-link functionality and the design being symetrical to
the confguration of link tolerance.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In previous commit, we changed the default emulated MTU for UDP bearers
to 14k.

This commit adds the functionality to set/change the default value
by configuring new MTU for UDP media. UDP bearer(s) have to be disabled
and enabled back for the new MTU to take effect.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, all bearers are configured with MTU value same as the
underlying L2 device. However, in case of bearers with media type
UDP, higher throughput is possible with a fixed and higher emulated
MTU value than adapting to the underlying L2 MTU.

In this commit, we introduce a parameter mtu in struct tipc_media
and a default value is set for UDP. A default value of 14k
was determined by experimentation and found to have a higher throughput
than 16k. MTU for UDP bearers are assigned the above set value of
media MTU.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added the ndo to gather VF statistics through the PF.

Collect VF statistics via mailbox from VF.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kunihiko Hayashi says:

====================
ave: fix the activation issues for some UniPhier SoCs

This add the following stuffs to fix the activation issues and satisfy
requirements for AVE ethernet driver implemented on some UniPhier SoCs.

- Add support for additional necessary clocks and resets, because the kernel
  is stalled on Pro4 due to lack of them.

- Check whether the SoC supports the specified phy-mode

- Add DT property support indicating system controller that has the feature
  for configurating phy-mode including built-in phy on LD11.

v1: https://www.spinics.net/lists/netdev/msg494904.html

Changes since v1:
- Add 'Reviewed-by' lines
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for specifying system controller that configures
phy-mode setting.

According to the DT property "phy-mode", it's necessary to configure the
controller, which is used to choose the settings of the MAC suitable,
for example, mdio pin connections, internal clocks, and so on.

Supported phy-modes are SoC-dependent. The driver allows phy-mode to set
"internal" if the SoC has a built-in PHY, and {"mii", "rmii", "rgmii"}
if the SoC supports each mode. So we have to check whether the phy-mode
is valid or not.

This adds the following features for each SoC:
- check whether the SoC supports the specified phy-mode
- configure the controller accroding to phy-mode

The DT property accepts one argument to distinguish them for multiple MAC
instances.

ethernet@65000000 {
	...
	socionext,syscon-phy-mode = <&soc_glue 0>;
};

ethernet@65200000 {
	...
	socionext,syscon-phy-mode = <&soc_glue 1>;
};
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add "socionext,syscon-phy-mode" property to specify system controller that
configures the settings about phy-mode.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the link is becoming up for Pro4 SoC, the kernel is stalled
due to some missing clocks and resets.

The AVE block for Pro4 is connected to the GIO bus in the SoC.
Without its clock/reset, the access to the AVE register makes the
system stall.

In the same way, another MAC clock for Giga-bit Connection and
the PHY clock are also required for Pro4 to activate the Giga-bit feature
and to recognize the PHY.

To satisfy these requirements, this patch adds support for multiple clocks
and resets, and adds the clock-names and reset-names to the binding because
we need to distinguish clock/reset for the AVE main block and the others.

Also, make the resets a required property. Currently, "reset is
optional" relies on that the bootloader or firmware has deasserted
the reset before booting the kernel.  Drivers should work without
such expectation.

Fixes: 4c270b55 ("net: ethernet: socionext: add AVE ethernet driver")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

mdiobus_register will search for any mdiobus board info registered for
the bus being registered. If found, it will probe devices on the bus.
That device, if for example it is an ethernet switch, may then try to
register an mdio bus. Thus we need to allow recursive calls to
mdiobus_register.

Holding the mdio_board_lock will cause a deadlock during this
recursion. Release the lock and use list_for_each_entry_safe.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Schmitz says:

====================
New network driver for Amiga X-Surf 100 (m68k)

[This is a resend of my v3 series which was based on the wrong version and
tree. Only substantial change is to Asix AX99796B PHY driver.]

This patch series adds support for the Individual Computers X-Surf 100
network card for m68k Amiga, a network adapter based on the AX88796 chip set.

The driver was originally written for kernel version 3.19 by Michael Karcher
(see CC:), and adapted to 4.16+ for submission to netdev by me. Questions
regarding motivation for some of the changes are probably best directed at
Michael Karcher.

The driver has been tested by Adrian <glaubitz@physik.fu-berlin.de> who will
send his Tested-by tag separately.

A few changes to the ax88796 driver were required:
- to read the MAC address, some setup of the ax99796 chip must be done,
- attach to the MII bus only on device open to allow module unloading,
- allow to supersede ax_block_input/ax_block_output by card-specific
  optimized code,
- use an optional interrupt status callback to allow easier sharing of the
  card interrupt,
- set IRQF_SHARED if platform IRQ resource is marked shareable

The Asix Electronix PHY used on the X-Surf 100 is buggy, and causes the
software reset to hang if the previous command sent to the PHY was also
a soft reset. This bug requires addition of a PHY driver for Asix PHYs
to provide a fixed .soft_reset function, included in this series.

Some additional cleanup:
- do not attempt to free IRQ in ax_remove (complements 82533ad9),
- clear platform drvdata on probe fail and module remove.

Changes since v1:

Raised in review by Andrew Lunn:
- move MII code around to avoid need for forward declaration,
- combine patches 2 and 7 to add cleanup in error path

Changes since v2:

- corrected authorship attribution to Michael Karcher

Suggested by Geert Uytterhoeven:
- use ei_local->reset_8390() instead of duplicating ax_reset_8390(),
- use %pR to format struct resource pointers,
- assign pdev and xs100 pointers in declaration,
- don't split error messages,
- change Kconfig logic to only require XSURF100 set on Amiga

Suggested by Andrew Lunn:
- add COMPILE_TEST to ax88796 Kconfig options,
- use new Asix PHY driver for X-Surf 100

Suggested by Andrew Lunn/Finn Thain:
- declare struct sk_buff in ax88796.h,
- correct whitespace error in ax88796.h

Changes since v3:

- various checkpatch cleanup

Andrew Lunn:
- don't duplicate genphy_soft_reset in Asix PHY driver, just call
  genphy_soft_reset after writing zero to control register
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add platform device driver to populate the ax88796 platform data from
information provided by the XSurf100 zorro device driver. The ax88796
module will be loaded through this module's probe function.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The net device struct pointer is stored as platform device drvdata on
module probe - clear the drvdata entry on probe fail there, as well as
when unloading the module.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On the Amiga X-Surf100, the network card interrupt is shared with many
other interrupt sources, so requires the IRQF_SHARED flag to register.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To be able to tell the ax88796 driver whether it is sensible to enter
the 8390 interrupt handler, an "is this interrupt caused by the 88796"
callback has been added to the ax_plat_data structure (with NULL being
compatible to the previous behaviour).
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add platform specific hooks for block transfer reads/writes of packet
buffer data, superseding the default provided ax_block_input/output.
Currently used for m68k Amiga XSurf100.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This complements the fix in 82533ad9 ("net: ethernet: ax88796:
don't call free_irq without request_irq first") that removed the
free_irq call in the error path of probe, to also not call free_irq
when remove is called to revert the effects of probe.

Fixes: 82533ad9 (net: ethernet: ax88796: don't call free_irq without request_irq first)
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call ax_mii_init in ax_open(), and unregister/remove mdiobus resources
in ax_close().

This is needed to be able to unload the module, as the module is busy
while the MII bus is attached.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

To read the MAC address from the (virtual) SAprom, the remote DMA
unit needs to be set up like for every other process access to card-local
memory.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Asix Electronics PHY found on the X-Surf 100 Amiga Zorro network
card by Individual Computers is buggy, and needs the reset bit toggled
as workaround to make a PHY soft reset succeed.

Add workaround driver just for this special case.

Suggested in xsurf100 patch series review by Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Modernize mdio-gpio

This patchset is inspired by a previous version by Linus Walleij

It reworks the mdio-gpio code to make use of gpio descriptors instead
of gpio numbers. However compared to the previous version, it retains
support for platform devices. It does however remove the platform_data
header file. The needed GPIOs are now passed by making use of a gpiod
lookup table. e.g:

static struct gpiod_lookup_table zii_scu_mdio_gpiod_table = {
	.dev_id = "mdio-gpio.0",
	.table = {
		GPIO_LOOKUP_IDX("gpio_ich", 17, NULL, MDIO_GPIO_MDC,
				GPIO_ACTIVE_HIGH),
		GPIO_LOOKUP_IDX("gpio_ich", 2, NULL, MDIO_GPIO_MDIO,
				GPIO_ACTIVE_HIGH),
		GPIO_LOOKUP_IDX("gpio_ich", 21, NULL, MDIO_GPIO_MDO,
				GPIO_ACTIVE_LOW),
	},
};
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The platform data header file is now unused. Remove it, but add
an extra include which it brought in.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The GPIOs are described in device tree using a list, without names.
Add defines to indicate what each index in the list means. These
defines should also be used by platform devices passing GPIOs via a
GPIO lookup table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same parsing code can be used for both OF and platform devices, if
the platform device uses a gpiod_lookup_table. Parse these properties
directly into the bitbang structure, rather than use an intermediate
platform data structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moving the allocation of this structure to the probe function is a
step towards making it the core data structure of the driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This simplifies the code, removing the need to handle active low
flags, etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

No current devices use IRQs in platform data, so remove support for
it. The MDIO core will also initialise the new bus such that all
addresses are polled, so remove the unneeded re-initialisation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mdio-gpio driver was the only user of the interface reset option.
Since it no longer uses it, remove it from the bit banging code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The platform data can contain a function to call to reset
the bit banging interface. It is not used, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Seems like an old typ0.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
net/ipv6: followup to fib6_info change

Followup to fib change for IPv6.

First 2 patches rename fib6_info struct elements to match its name,
and rename addrconf_dst_alloc to match what it returns.

Patches 3-7 refactor the code to remove the need for fib6_idev reducing
fib6_info by another 8 bytes to 200 bytes.

Patch 8 fixes the gfp flags argument to addrconf_prefix_route in a
couple of places.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric noticed that __ipv6_ifa_notify is called under rcu_read_lock, so
the gfp argument to addrconf_prefix_route can not be GFP_KERNEL.

While scrubbing other calls I noticed addrconf_addr_gen has one
place with GFP_ATOMIC that can be GFP_KERNEL.

Fixes: acb54e3c ("net/ipv6: Add gfp_flags to route add functions")
Reported-by: syzbot+2add39b05179b31f912f@syzkaller.appspotmail.com
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib6_idev can be obtained from __in6_dev_get on the nexthop device
rather than caching it in the fib6_info. Remove it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>