- 10 Feb, 2022 8 commits
-
-
Victor Erminpour authored
When building with automatic stack variable initialization, GCC 12 complains about variables defined outside of switch case statements. Move the variable outside the switch, which silences the warning: ./net/mpls/af_mpls.c:1624:21: error: statement will never be executed [-Werror=switch-unreachable] 1624 | int err; | ^~~ Signed-off-by:Victor Erminpour <victor.erminpour@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Robert-Ionut Alexa authored
The netdev should be unregistered before we are disconnecting from the MAC/PHY so that the dev_close callback is called and the PHY and the phylink workqueues are actually stopped before we are disconnecting and destroying the phylink instance. Fixes: 71947923 ("dpaa2-eth: add MAC/PHY support through phylink") Signed-off-by:
Robert-Ionut Alexa <robert-ionut.alexa@nxp.com> Signed-off-by:
Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by:
-
Tom Rix authored
Remove the second 'to'. Signed-off-by:
Tom Rix <trix@redhat.com> Signed-off-by:
-
Marc St-Amand authored
Single page and coherent memory blocks can use different DMA masks when the macb accesses physical memory directly. The kernel is clever enough to allocate pages that fit into the requested address width. When using the ARM SMMU, the DMA mask must be the same for single pages and big coherent memory blocks. Otherwise the translation tables turn into one big mess. [ 74.959909] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK [ 74.959989] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1 [ 75.173939] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK [ 75.173955] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1 Since using the same DMA mask does not hurt direct 1:1 physical memory mappings, this commit always aligns DMA and coherent masks. Signed-off-by:
Marc St-Amand <mstamand@ciena.com> Signed-off-by:
Harini Katakam <harini.katakam@xilinx.com> Acked-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Tested-by:
Conor Dooley <conor.dooley@microchip.com> Signed-off-by:
-
Jakub Kicinski authored
Mat Martineau says: ==================== mptcp: Fixes for 5.17 Patch 1 fixes a MPTCP selftest bug that combined the results of two separate tests in the test output. Patch 2 fixes a problem where advertised IPv6 addresses were not actually available for incoming MP_JOIN requests. ==================== Link: https://lore.kernel.org/r/20220210012508.226880-1-mathew.j.martineau@linux.intel.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Kishen Maloor authored
This change updates mptcp_pm_nl_create_listen_socket() to create listening sockets bound to IPv6 addresses (where IPv6 is supported). Fixes: 1729cf18 ("mptcp: create the listening socket for new port") Acked-by:
Geliang Tang <geliang.tang@suse.com> Signed-off-by:
Kishen Maloor <kishen.maloor@intel.com> Signed-off-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by:
-
Matthieu Baerts authored
This function also writes the name of the test with its ID, making clear a new test has been executed. Without that, the ADD_ADDR results from this test was appended at the end of the previous test causing confusions. Especially when the second test was failing, we had: 17 signal invalid addresses syn[ ok ] - synack[ ok ] - ack[ ok ] add[ ok ] - echo [ ok ] add[fail] got 2 ADD_ADDR[s] expected 3 In fact, this 17th test was OK but not the 18th one. Now we have: 17 signal invalid addresses syn[ ok ] - synack[ ok ] - ack[ ok ] add[ ok ] - echo [ ok ] 18 signal addresses race test syn[fail] got 2 JOIN[s] syn expected 3 - synack[fail] got 2 JOIN[s] synack expected - ack[fail] got 2 JOIN[s] ack expected 3 add[fail] got 2 ADD_ADDR[s] expected 3 Fixes: 33c563ad ("selftests: mptcp: add_addr and echo race test") Reported-by:Paolo Abeni <pabeni@redhat.com> Signed-off-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by:
-
Slark Xiao authored
Dell DW5829e same as DW5821e except the CAT level. DW5821e supports CAT16 but DW5829e supports CAT9. Also, DW5829e includes normal and eSIM type. Please see below test evidence: T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 5 Spd=5000 MxCh= 0 D: Ver= 3.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 1 P: Vendor=413c ProdID=81e6 Rev=03.18 S: Manufacturer=Dell Inc. S: Product=DW5829e Snapdragon X20 LTE S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 7 Spd=5000 MxCh= 0 D: Ver= 3.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 1 P: Vendor=413c ProdID=81e4 Rev=03.18 S: Manufacturer=Dell Inc. S: Product=DW5829e-eSIM Snapdragon X20 LTE S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option Signed-off-by:
Slark Xiao <slark_xiao@163.com> Acked-by:
Bjørn Mork <bjorn@mork.no> Link: https://lore.kernel.org/r/20220209024717.8564-1-slark_xiao@163.comSigned-off-by:
-
- 09 Feb, 2022 30 commits
-
-
David S. Miller authored
Xin Long says: ==================== vlan: fix a netdev refcnt leak for QinQ This issue can be simply reproduced by: # ip link add dummy0 type dummy # ip link add link dummy0 name dummy0.1 type vlan id 1 # ip link add link dummy0.1 name dummy0.1.2 type vlan id 2 # rmmod 8021q unregister_netdevice: waiting for dummy0.1 to become free. Usage count = 1 So as to fix it, adjust vlan_dev_uninit() in Patch 1/1 so that it won't be called twice for the same device, then do the fix in vlan_dev_uninit() in Patch 2/2. ==================== Signed-off-by: -
Xin Long authored
Shuang Li reported an QinQ issue by simply doing: # ip link add dummy0 type dummy # ip link add link dummy0 name dummy0.1 type vlan id 1 # ip link add link dummy0.1 name dummy0.1.2 type vlan id 2 # rmmod 8021q unregister_netdevice: waiting for dummy0.1 to become free. Usage count = 1 When rmmods 8021q, all vlan devs are deleted from their real_dev's vlan grp and added into list_kill by unregister_vlan_dev(). dummy0.1 is unregistered before dummy0.1.2, as it's using for_each_netdev() in __rtnl_kill_links(). When unregisters dummy0.1, dummy0.1.2 is not unregistered in the event of NETDEV_UNREGISTER, as it's been deleted from dummy0.1's vlan grp. However, due to dummy0.1.2 still holding dummy0.1, dummy0.1 will keep waiting in netdev_wait_allrefs(), while dummy0.1.2 will never get unregistered and release dummy0.1, as it delays dev_put until calling dev->priv_destructor, vlan_dev_free(). This issue was introduced by Commit 563bcbae ("net: vlan: fix a UAF in vlan_dev_real_dev()"), and this patch is to fix it by moving dev_put() into vlan_dev_uninit(), which is called after NETDEV_UNREGISTER event but before netdev_wait_allrefs(). Fixes: 563bcbae ("net: vlan: fix a UAF in vlan_dev_real_dev()") Reported-by:
Shuang Li <shuali@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Xin Long authored
This patch is to introduce vlan_dev_free_egress_priority() to free egress priority for vlan dev, and keep vlan_dev_uninit() static as .ndo_uninit. It makes the code more clear and safer when adding new code in vlan_dev_uninit() in the future. Signed-off-by:
-
Duoming Zhou authored
The ax25_kill_by_device() will set s->ax25_dev = NULL and call ax25_disconnect() to change states of ax25_cb and sock, if we call ax25_bind() before ax25_kill_by_device(). However, if we call ax25_bind() again between the window of ax25_kill_by_device() and ax25_dev_device_down(), the values and states changed by ax25_kill_by_device() will be reassigned. Finally, ax25_dev_device_down() will deallocate net_device. If we dereference net_device in syscall functions such as ax25_release(), ax25_sendmsg(), ax25_getsockopt(), ax25_getname() and ax25_info_show(), a UAF bug will occur. One of the possible race conditions is shown below: (USE) | (FREE) ax25_bind() | | ax25_kill_by_device() ax25_bind() | ax25_connect() | ... | ax25_dev_device_down() | ... | dev_put_track(dev, ...) //FREE ax25_release() | ... ax25_send_control() | alloc_skb() //USE | the corresponding fail log is shown below: =============================================================== BUG: KASAN: use-after-free in ax25_send_control+0x43/0x210 ... Call Trace: ... ax25_send_control+0x43/0x210 ax25_release+0x2db/0x3b0 __sock_release+0x6d/0x120 sock_close+0xf/0x20 __fput+0x11f/0x420 ... Allocated by task 1283: ... __kasan_kmalloc+0x81/0xa0 alloc_netdev_mqs+0x5a/0x680 mkiss_open+0x6c/0x380 tty_ldisc_open+0x55/0x90 ... Freed by task 1969: ... kfree+0xa3/0x2c0 device_release+0x54/0xe0 kobject_put+0xa5/0x120 tty_ldisc_kill+0x3e/0x80 ... In order to fix these UAF bugs caused by rebinding operation, this patch adds dev_hold_track() into ax25_bind() and corresponding dev_put_track() into ax25_kill_by_device(). Signed-off-by:Duoming Zhou <duoming@zju.edu.cn> Signed-off-by:
-
Vladimir Oltean authored
Rafael reports that on a system with LX2160A and Marvell DSA switches, if a reboot occurs while the DSA master (dpaa2-eth) is up, the following panic can be seen: systemd-shutdown[1]: Rebooting. Unable to handle kernel paging request at virtual address 00a0000800000041 [00a0000800000041] address between user and kernel address ranges Internal error: Oops: 96000004 [#1] PREEMPT SMP CPU: 6 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00042-g8f5585009b24 #32 pc : dsa_slave_netdevice_event+0x130/0x3e4 lr : raw_notifier_call_chain+0x50/0x6c Call trace: dsa_slave_netdevice_event+0x130/0x3e4 raw_notifier_call_chain+0x50/0x6c call_netdevice_notifiers_info+0x54/0xa0 __dev_close_many+0x50/0x130 dev_close_many+0x84/0x120 unregister_netdevice_many+0x130/0x710 unregister_netdevice_queue+0x8c/0xd0 unregister_netdev+0x20/0x30 dpaa2_eth_remove+0x68/0x190 fsl_mc_driver_remove+0x20/0x5c __device_release_driver+0x21c/0x220 device_release_driver_internal+0xac/0xb0 device_links_unbind_consumers+0xd4/0x100 __device_release_driver+0x94/0x220 device_release_driver+0x28/0x40 bus_remove_device+0x118/0x124 device_del+0x174/0x420 fsl_mc_device_remove+0x24/0x40 __fsl_mc_device_remove+0xc/0x20 device_for_each_child+0x58/0xa0 dprc_remove+0x90/0xb0 fsl_mc_driver_remove+0x20/0x5c __device_release_driver+0x21c/0x220 device_release_driver+0x28/0x40 bus_remove_device+0x118/0x124 device_del+0x174/0x420 fsl_mc_bus_remove+0x80/0x100 fsl_mc_bus_shutdown+0xc/0x1c platform_shutdown+0x20/0x30 device_shutdown+0x154/0x330 __do_sys_reboot+0x1cc/0x250 __arm64_sys_reboot+0x20/0x30 invoke_syscall.constprop.0+0x4c/0xe0 do_el0_svc+0x4c/0x150 el0_svc+0x24/0xb0 el0t_64_sync_handler+0xa8/0xb0 el0t_64_sync+0x178/0x17c It can be seen from the stack trace that the problem is that the deregistration of the master causes a dev_close(), which gets notified as NETDEV_GOING_DOWN to dsa_slave_netdevice_event(). But dsa_switch_shutdown() has already run, and this has unregistered the DSA slave interfaces, and yet, the NETDEV_GOING_DOWN handler attempts to call dev_close_many() on those slave interfaces, leading to the problem. The previous attempt to avoid the NETDEV_GOING_DOWN on the master after dsa_switch_shutdown() was called seems improper. Unregistering the slave interfaces is unnecessary and unhelpful. Instead, after the slaves have stopped being uppers of the DSA master, we can now reset to NULL the master->dsa_ptr pointer, which will make DSA start ignoring all future notifier events on the master. Fixes: 0650bf52 ("net: dsa: be compatible with masters which unregister on shutdown") Reported-by:
Rafael Richter <rafael.richter@gin.de> Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
Raju Rangoju authored
Hardware interrupts are enabled during the pci probe, however, they are not disabled during pci removal. Disable all hardware interrupts during pci removal to avoid any issues. Fixes: e7537740 ("amd-xgbe: Update PCI support to use new IRQ functions") Suggested-by:
Selwin Sebastian <Selwin.Sebastian@amd.com> Signed-off-by:
Raju Rangoju <Raju.Rangoju@amd.com> Signed-off-by:
-
Jon Maloy authored
It would be easy to craft a message containing an illegal binding table update operation. This is handled correctly by the code, but the corresponding warning printout is not rate limited as is should be. We fix this now. Fixes: b97bf3fd ("[TIPC] Initial merge") Signed-off-by:
Jon Maloy <jmaloy@redhat.com> Signed-off-by:
-
Joel Stanley authored
Fix loading of the driver when built as a module. Fixes: f160e994 ("net: phy: Add mdio-aspeed") Signed-off-by:
Joel Stanley <joel@jms.id.au> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Acked-by:
Andrew Jeffery <andrew@aj.id.au> Signed-off-by:
-
Eric Dumazet authored
veth being NETIF_F_LLTX enabled, we need to be more careful whenever we read/write rq->rx_notify_masked. BUG: KCSAN: data-race in veth_xmit / veth_xmit write to 0xffff888133d9a9f8 of 1 bytes by task 23552 on cpu 0: __veth_xdp_flush drivers/net/veth.c:269 [inline] veth_xmit+0x307/0x470 drivers/net/veth.c:350 __netdev_start_xmit include/linux/netdevice.h:4683 [inline] netdev_start_xmit include/linux/netdevice.h:4697 [inline] xmit_one+0x105/0x2f0 net/core/dev.c:3473 dev_hard_start_xmit net/core/dev.c:3489 [inline] __dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116 dev_queue_xmit+0x13/0x20 net/core/dev.c:4149 br_dev_queue_push_xmit+0x3ce/0x430 net/bridge/br_forward.c:53 NF_HOOK include/linux/netfilter.h:307 [inline] br_forward_finish net/bridge/br_forward.c:66 [inline] NF_HOOK include/linux/netfilter.h:307 [inline] __br_forward+0x2e4/0x400 net/bridge/br_forward.c:115 br_flood+0x521/0x5c0 net/bridge/br_forward.c:242 br_dev_xmit+0x8b6/0x960 __netdev_start_xmit include/linux/netdevice.h:4683 [inline] netdev_start_xmit include/linux/netdevice.h:4697 [inline] xmit_one+0x105/0x2f0 net/core/dev.c:3473 dev_hard_start_xmit net/core/dev.c:3489 [inline] __dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116 dev_queue_xmit+0x13/0x20 net/core/dev.c:4149 neigh_hh_output include/net/neighbour.h:525 [inline] neigh_output include/net/neighbour.h:539 [inline] ip_finish_output2+0x6f8/0xb70 net/ipv4/ip_output.c:228 ip_finish_output+0xfb/0x240 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:296 [inline] ip_output+0xf3/0x1a0 net/ipv4/ip_output.c:430 dst_output include/net/dst.h:451 [inline] ip_local_out net/ipv4/ip_output.c:126 [inline] ip_send_skb+0x6e/0xe0 net/ipv4/ip_output.c:1570 udp_send_skb+0x641/0x880 net/ipv4/udp.c:967 udp_sendmsg+0x12ea/0x14c0 net/ipv4/udp.c:1254 inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819 sock_sendmsg_nosec net/socket.c:705 [inline] sock_sendmsg net/socket.c:725 [inline] ____sys_sendmsg+0x39a/0x510 net/socket.c:2413 ___sys_sendmsg net/socket.c:2467 [inline] __sys_sendmmsg+0x267/0x4c0 net/socket.c:2553 __do_sys_sendmmsg net/socket.c:2582 [inline] __se_sys_sendmmsg net/socket.c:2579 [inline] __x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae read to 0xffff888133d9a9f8 of 1 bytes by task 23563 on cpu 1: __veth_xdp_flush drivers/net/veth.c:268 [inline] veth_xmit+0x2d6/0x470 drivers/net/veth.c:350 __netdev_start_xmit include/linux/netdevice.h:4683 [inline] netdev_start_xmit include/linux/netdevice.h:4697 [inline] xmit_one+0x105/0x2f0 net/core/dev.c:3473 dev_hard_start_xmit net/core/dev.c:3489 [inline] __dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116 dev_queue_xmit+0x13/0x20 net/core/dev.c:4149 br_dev_queue_push_xmit+0x3ce/0x430 net/bridge/br_forward.c:53 NF_HOOK include/linux/netfilter.h:307 [inline] br_forward_finish net/bridge/br_forward.c:66 [inline] NF_HOOK include/linux/netfilter.h:307 [inline] __br_forward+0x2e4/0x400 net/bridge/br_forward.c:115 br_flood+0x521/0x5c0 net/bridge/br_forward.c:242 br_dev_xmit+0x8b6/0x960 __netdev_start_xmit include/linux/netdevice.h:4683 [inline] netdev_start_xmit include/linux/netdevice.h:4697 [inline] xmit_one+0x105/0x2f0 net/core/dev.c:3473 dev_hard_start_xmit net/core/dev.c:3489 [inline] __dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116 dev_queue_xmit+0x13/0x20 net/core/dev.c:4149 neigh_hh_output include/net/neighbour.h:525 [inline] neigh_output include/net/neighbour.h:539 [inline] ip_finish_output2+0x6f8/0xb70 net/ipv4/ip_output.c:228 ip_finish_output+0xfb/0x240 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:296 [inline] ip_output+0xf3/0x1a0 net/ipv4/ip_output.c:430 dst_output include/net/dst.h:451 [inline] ip_local_out net/ipv4/ip_output.c:126 [inline] ip_send_skb+0x6e/0xe0 net/ipv4/ip_output.c:1570 udp_send_skb+0x641/0x880 net/ipv4/udp.c:967 udp_sendmsg+0x12ea/0x14c0 net/ipv4/udp.c:1254 inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819 sock_sendmsg_nosec net/socket.c:705 [inline] sock_sendmsg net/socket.c:725 [inline] ____sys_sendmsg+0x39a/0x510 net/socket.c:2413 ___sys_sendmsg net/socket.c:2467 [inline] __sys_sendmmsg+0x267/0x4c0 net/socket.c:2553 __do_sys_sendmmsg net/socket.c:2582 [inline] __se_sys_sendmmsg net/socket.c:2579 [inline] __x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae value changed: 0x00 -> 0x01 Reported by Kernel Concurrency Sanitizer on: CPU: 1 PID: 23563 Comm: syz-executor.5 Not tainted 5.17.0-rc2-syzkaller-00064-gc36c04c2 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Fixes: 948d4f21 ("veth: Add driver XDP") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'linux-can-fixes-for-5.17-20220209' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2022-02-09 this is a pull request of 2 patches for net/master. Oliver Hartkopp contributes 2 fixes for the CAN ISOTP protocol. ==================== Signed-off-by:
-
Duoming Zhou authored
The ax25_disconnect() in ax25_kill_by_device() is not protected by any locks, thus there is a race condition between ax25_disconnect() and ax25_destroy_socket(). when ax25->sk is assigned as NULL by ax25_destroy_socket(), a NULL pointer dereference bug will occur if site (1) or (2) dereferences ax25->sk. ax25_kill_by_device() | ax25_release() ax25_disconnect() | ax25_destroy_socket() ... | if(ax25->sk != NULL) | ... ... | ax25->sk = NULL; bh_lock_sock(ax25->sk); //(1) | ... ... | bh_unlock_sock(ax25->sk); //(2)| This patch moves ax25_disconnect() into lock_sock(), which can synchronize with ax25_destroy_socket() in ax25_release(). Fail log: =============================================================== BUG: kernel NULL pointer dereference, address: 0000000000000088 ... RIP: 0010:_raw_spin_lock+0x7e/0xd0 ... Call Trace: ax25_disconnect+0xf6/0x220 ax25_device_event+0x187/0x250 raw_notifier_call_chain+0x5e/0x70 dev_close_many+0x17d/0x230 rollback_registered_many+0x1f1/0x950 unregister_netdevice_queue+0x133/0x200 unregister_netdev+0x13/0x20 ... Signed-off-by: -
David S. Miller authored
Antoine Tenart says: ==================== net: fix issues when uncloning an skb dst+metadata This fixes two issues when uncloning an skb dst+metadata in tun_dst_unclone; this was initially reported by Vlad Buslov[1]. Because of the memory leak fixed by patch 2, the issue in patch 1 never happened in practice. tun_dst_unclone is called from two different places, one in geneve/vxlan to handle PMTU and one in net/openvswitch/actions.c where it is used to retrieve tunnel information. While both Vlad and I tested the former, we could not for the latter. I did spend quite some time trying to, but that code path is not easy to trigger. Code inspection shows this should be fine, the tunnel information (dst+metadata) is uncloned and the skb it is referenced from is only consumed after all accesses to the tunnel information are done: do_execute_actions output_userspace dev_fill_metadata_dst <- dst+metadata is uncloned ovs_dp_upcall queue_userspace_packet ovs_nla_put_tunnel_info <- metadata (tunnel info) is accessed consume_skb <- dst+metadata is freed Thanks! Antoine [1] https://lore.kernel.org/all/ygnhh79yluw2.fsf@nvidia.com/T/#m2f814614a4f5424cea66bbff7297f692b59b69a0 ==================== Signed-off-by: -
Antoine Tenart authored
When uncloning an skb dst and its associated metadata, a new dst+metadata is allocated and later replaces the old one in the skb. This is helpful to have a non-shared dst+metadata attached to a specific skb. The issue is the uncloned dst+metadata is initialized with a refcount of 1, which is increased to 2 before attaching it to the skb. When tun_dst_unclone returns, the dst+metadata is only referenced from a single place (the skb) while its refcount is 2. Its refcount will never drop to 0 (when the skb is consumed), leading to a memory leak. Fix this by removing the call to dst_hold in tun_dst_unclone, as the dst+metadata refcount is already 1. Fixes: fc4099f1 ("openvswitch: Fix egress tunnel info.") Cc: Pravin B Shelar <pshelar@ovn.org> Reported-by:
Vlad Buslov <vladbu@nvidia.com> Tested-by:
Antoine Tenart <atenart@kernel.org> Signed-off-by:
-
Antoine Tenart authored
When uncloning an skb dst and its associated metadata a new dst+metadata is allocated and the tunnel information from the old metadata is copied over there. The issue is the tunnel metadata has references to cached dst, which are copied along the way. When a dst+metadata refcount drops to 0 the metadata is freed including the cached dst entries. As they are also referenced in the initial dst+metadata, this ends up in UaFs. In practice the above did not happen because of another issue, the dst+metadata was never freed because its refcount never dropped to 0 (this will be fixed in a subsequent patch). Fix this by initializing the dst cache after copying the tunnel information from the old metadata to also unshare the dst cache. Fixes: d71785ff ("net: add dst_cache to ovs vxlan lwtunnel") Cc: Paolo Abeni <pabeni@redhat.com> Reported-by:
-
Oliver Hartkopp authored
Commit 43a08c3b ("can: isotp: isotp_sendmsg(): fix TX buffer concurrent access in isotp_sendmsg()") introduced a new locking scheme that may render the userspace application in a locking state when an error is detected. This issue shows up under high load on simultaneously running isotp channels with identical configuration which is against the ISO specification and therefore breaks any reasonable PDU communication anyway. Fixes: 43a08c3b ("can: isotp: isotp_sendmsg(): fix TX buffer concurrent access in isotp_sendmsg()") Link: https://lore.kernel.org/all/20220209073601.25728-1-socketcan@hartkopp.net Cc: stable@vger.kernel.org Cc: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Oliver Hartkopp authored
When receiving a CAN frame the current code logic does not consider concurrently receiving processes which do not show up in real world usage. Ziyang Xuan writes: The following syz problem is one of the scenarios. so->rx.len is changed by isotp_rcv_ff() during isotp_rcv_cf(), so->rx.len equals 0 before alloc_skb() and equals 4096 after alloc_skb(). That will trigger skb_over_panic() in skb_put(). ======================================================= CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 5.16.0-rc8-syzkaller #0 RIP: 0010:skb_panic+0x16c/0x16e net/core/skbuff.c:113 Call Trace: <TASK> skb_over_panic net/core/skbuff.c:118 [inline] skb_put.cold+0x24/0x24 net/core/skbuff.c:1990 isotp_rcv_cf net/can/isotp.c:570 [inline] isotp_rcv+0xa38/0x1e30 net/can/isotp.c:668 deliver net/can/af_can.c:574 [inline] can_rcv_filter+0x445/0x8d0 net/can/af_can.c:635 can_receive+0x31d/0x580 net/can/af_can.c:665 can_rcv+0x120/0x1c0 net/can/af_can.c:696 __netif_receive_skb_one_core+0x114/0x180 net/core/dev.c:5465 __netif_receive_skb+0x24/0x1b0 net/core/dev.c:5579 Therefore we make sure the state changes and data structures stay consistent at CAN frame reception time by adding a spin_lock in isotp_rcv(). This fixes the issue reported by syzkaller but does not affect real world operation. Fixes: e057dd3f ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/linux-can/d7e69278-d741-c706-65e1-e87623d9a8e8@huawei.com/T/ Link: https://lore.kernel.org/all/20220208200026.13783-1-socketcan@hartkopp.net Cc: stable@vger.kernel.org Reported-by: syzbot+4c63f36709a642f801c5@syzkaller.appspotmail.com Reported-by:
Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by:
-
Louis Peens authored
When looking for a global mac index the extra NFP_TUN_PRE_TUN_IDX_BIT that gets set if nfp_flower_is_supported_bridge is true is not taken into account. Consequently the path that should release the ida_index in cleanup is never triggered, causing messages like: nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex. nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex. nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex. after NFP_MAX_MAC_INDEX number of reconfigs. Ultimately this lead to new tunnel flows not being offloaded. Fix this by unsetting the NFP_TUN_PRE_TUN_IDX_BIT before checking if the port is of type OTHER. Fixes: 2e0bc7f3 ("nfp: flower: encode mac indexes with pre-tunnel rule check") Signed-off-by:Louis Peens <louis.peens@corigine.com> Signed-off-by:
Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20220208101453.321949-1-simon.horman@corigine.comSigned-off-by:
-
Eric Dumazet authored
ip[6]mr_free_table() can only be called under RTNL lock. RTNL: assertion failed at net/core/dev.c (10367) WARNING: CPU: 1 PID: 5890 at net/core/dev.c:10367 unregister_netdevice_many+0x1246/0x1850 net/core/dev.c:10367 Modules linked in: CPU: 1 PID: 5890 Comm: syz-executor.2 Not tainted 5.16.0-syzkaller-11627-g422ee58dc0ef #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:unregister_netdevice_many+0x1246/0x1850 net/core/dev.c:10367 Code: 0f 85 9b ee ff ff e8 69 07 4b fa ba 7f 28 00 00 48 c7 c6 00 90 ae 8a 48 c7 c7 40 90 ae 8a c6 05 6d b1 51 06 01 e8 8c 90 d8 01 <0f> 0b e9 70 ee ff ff e8 3e 07 4b fa 4c 89 e7 e8 86 2a 59 fa e9 ee RSP: 0018:ffffc900046ff6e0 EFLAGS: 00010286 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: ffff888050f51d00 RSI: ffffffff815fa008 RDI: fffff520008dfece RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: ffffffff815f3d6e R11: 0000000000000000 R12: 00000000fffffff4 R13: dffffc0000000000 R14: ffffc900046ff750 R15: ffff88807b7dc000 FS: 00007f4ab736e700(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fee0b4f8990 CR3: 000000001e7d2000 CR4: 00000000003506e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> mroute_clean_tables+0x244/0xb40 net/ipv6/ip6mr.c:1509 ip6mr_free_table net/ipv6/ip6mr.c:389 [inline] ip6mr_rules_init net/ipv6/ip6mr.c:246 [inline] ip6mr_net_init net/ipv6/ip6mr.c:1306 [inline] ip6mr_net_init+0x3f0/0x4e0 net/ipv6/ip6mr.c:1298 ops_init+0xaf/0x470 net/core/net_namespace.c:140 setup_net+0x54f/0xbb0 net/core/net_namespace.c:331 copy_net_ns+0x318/0x760 net/core/net_namespace.c:475 create_new_namespaces+0x3f6/0xb20 kernel/nsproxy.c:110 copy_namespaces+0x391/0x450 kernel/nsproxy.c:178 copy_process+0x2e0c/0x7300 kernel/fork.c:2167 kernel_clone+0xe7/0xab0 kernel/fork.c:2555 __do_sys_clone+0xc8/0x110 kernel/fork.c:2672 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f4ab89f9059 Code: Unable to access opcode bytes at RIP 0x7f4ab89f902f. RSP: 002b:00007f4ab736e118 EFLAGS: 00000206 ORIG_RAX: 0000000000000038 RAX: ffffffffffffffda RBX: 00007f4ab8b0bf60 RCX: 00007f4ab89f9059 RDX: 0000000020000280 RSI: 0000000020000270 RDI: 0000000040200000 RBP: 00007f4ab8a5308d R08: 0000000020000300 R09: 0000000020000300 R10: 00000000200002c0 R11: 0000000000000206 R12: 0000000000000000 R13: 00007ffc3977cc1f R14: 00007f4ab736e300 R15: 0000000000022000 </TASK> Fixes: f243e5a7 ("ipmr,ip6mr: call ip6mr_free_table() on failure path") Signed-off-by:
-
Cai Huoqing authored
The LiteX driver uses devm io function API which needs HAS_IOMEM enabled, so add the dependency on HAS_IOMEM. Fixes: ee7da21a ("net: Add driver for LiteX's LiteETH network interface") Signed-off-by:
Cai Huoqing <cai.huoqing@linux.dev> Link: https://lore.kernel.org/r/20220208013308.6563-1-cai.huoqing@linux.devSigned-off-by:
-
Sukadev Bhattiprolu authored
If __ibmvnic_open() encounters an error such as when setting link state, it calls release_resources() which frees the napi structures needlessly. Instead, have __ibmvnic_open() only clean up the work it did so far (i.e. disable napi and irqs) and leave the rest to the callers. If caller of __ibmvnic_open() is ibmvnic_open(), it should release the resources immediately. If the caller is do_reset() or do_hard_reset(), they will release the resources on the next reset. This fixes following crash that occurred when running the drmgr command several times to add/remove a vnic interface: [102056] ibmvnic 30000003 env3: Disabling rx_scrq[6] irq [102056] ibmvnic 30000003 env3: Disabling rx_scrq[7] irq [102056] ibmvnic 30000003 env3: Replenished 8 pools Kernel attempted to read user page (10) - exploit attempt? (uid: 0) BUG: Kernel NULL pointer dereference on read at 0x00000010 Faulting instruction address: 0xc000000000a3c840 Oops: Kernel access of bad area, sig: 11 [#1] LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries ... CPU: 9 PID: 102056 Comm: kworker/9:2 Kdump: loaded Not tainted 5.16.0-rc5-autotest-g6441998e #1 Workqueue: events_long __ibmvnic_reset [ibmvnic] NIP: c000000000a3c840 LR: c0080000029b5378 CTR: c000000000a3c820 REGS: c0000000548e37e0 TRAP: 0300 Not tainted (5.16.0-rc5-autotest-g6441998e) MSR: 8000000000009033 <SF,EE,ME,IR,DR,RI,LE> CR: 28248484 XER: 00000004 CFAR: c0080000029bdd24 DAR: 0000000000000010 DSISR: 40000000 IRQMASK: 0 GPR00: c0080000029b55d0 c0000000548e3a80 c0000000028f0200 0000000000000000 ... NIP [c000000000a3c840] napi_enable+0x20/0xc0 LR [c0080000029b5378] __ibmvnic_open+0xf0/0x430 [ibmvnic] Call Trace: [c0000000548e3a80] [0000000000000006] 0x6 (unreliable) [c0000000548e3ab0] [c0080000029b55d0] __ibmvnic_open+0x348/0x430 [ibmvnic] [c0000000548e3b40] [c0080000029bcc28] __ibmvnic_reset+0x500/0xdf0 [ibmvnic] [c0000000548e3c60] [c000000000176228] process_one_work+0x288/0x570 [c0000000548e3d00] [c000000000176588] worker_thread+0x78/0x660 [c0000000548e3da0] [c0000000001822f0] kthread+0x1c0/0x1d0 [c0000000548e3e10] [c00000000000cf64] ret_from_kernel_thread+0x5c/0x64 Instruction dump: 7d2948f8 792307e0 4e800020 60000000 3c4c01eb 384239e0 f821ffd1 39430010 38a0fff6 e92d1100 f9210028 39200000 <e9030010> f9010020 60420000 e9210020 ---[ end trace 5f8033b08fd27706 ]--- Fixes: ed651a10 ("ibmvnic: Updated reset handling") Reported-by:
Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by:
Sukadev Bhattiprolu <sukadev@linux.ibm.com> Reviewed-by:
Dany Madden <drt@linux.ibm.com> Link: https://lore.kernel.org/r/20220208001918.900602-1-sukadev@linux.ibm.comSigned-off-by:
-
Jakub Kicinski authored
Vladimir Oltean says: ==================== More DSA fixes for devres + mdiobus_{alloc,register} The initial patch series "[net,0/2] Fix mdiobus users with devres" https://patchwork.kernel.org/project/netdevbpf/cover/20210920214209.1733768-1-vladimir.oltean@nxp.com/ fixed some instances where DSA drivers on slow buses (SPI, I2C) trigger a panic (changed since then to a warn) in mdiobus_free. That was due to devres calling mdiobus_free() with no prior mdiobus_unregister(), which again was due to commit ac3a68d5 ("net: phy: don't abuse devres in devm_mdiobus_register()") by Bartosz Golaszewski. Rafael Richter and Daniel Klauer report yet another variation on that theme, but this time it applies to any DSA switch driver, not just those on buses which have a "->shutdown() calls ->remove() which unregisters children" sequence. Their setup is that of an LX2160A DPAA2 SoC driving a Marvell DSA switch (MDIO). DPAA2 Ethernet drivers probe on the "fsl-mc" bus (drivers/bus/fsl-mc/fsl-mc-bus.c). This bus is meant to be the kernel-side representation of the networking objects kept by the Management Complex (MC) firmware. The fsl-mc bus driver has this pattern: static void fsl_mc_bus_shutdown(struct platform_device *pdev) { fsl_mc_bus_remove(pdev); } which proceeds to remove the children on the bus. Among those children, the dpaa2-eth network driver. When dpaa2-eth is a DSA master, this removal of the master on shutdown trips up the device link created by dsa_master_setup(), and as such, the Marvell switch is also removed. From this point on, readers can revisit the description of commits 74b6d7d1 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a ("net: dsa: don't allocate the slave_mii_bus using devres") since the prerequisites for the BUG_ON in mdiobus_free() have been accomplished if there is a devres mismatch between mdiobus_alloc() and mdiobus_register(). Most DSA drivers have this kind of mismatch, and upon my initial assessment I had not realized the possibility described above, so I didn't fix it. This patch series walks through all drivers and makes them use either fully devres, or no devres. I am aware that there are DSA drivers that are only known to be tested with a single DSA master, so some patches are probably overkill for them. But code is copy-pasted from so many sources without fully understanding the differences, that I think it's better to not leave an in-tree source of inspiration that may lead to subtle breakage if not adapted properly. ==================== Link: https://lore.kernel.org/r/20220207161553.579933-1-vladimir.oltean@nxp.comSigned-off-by: -
Vladimir Oltean authored
As explained in commits: 74b6d7d1 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The GSWIP switch is a platform device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the GSWIP switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The gswip driver has the code structure in place for orderly mdiobus removal, so just replace devm_mdiobus_alloc() with the non-devres variant, and add manual free where necessary, to ensure that we don't let devres free a still-registered bus. Fixes: ac3a68d5 ("net: phy: don't abuse devres in devm_mdiobus_register()") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Vladimir Oltean authored
Nobody in this driver calls mdiobus_unregister(), which is necessary if mdiobus_register() completes successfully. So if the devres callbacks that free the mdiobus get invoked (this is the case when unbinding the driver), mdiobus_free() will BUG if the mdiobus is still registered, which it is. My speculation is that this is due to the fact that prior to commit ac3a68d5 ("net: phy: don't abuse devres in devm_mdiobus_register()") from June 2020, _devm_mdiobus_free() used to call mdiobus_unregister(). But at the time that the mt7530 support was introduced in May 2021, the API was already changed. It's therefore likely that the blamed patch was developed on an older tree, and incorrectly adapted to net-next. This makes the Fixes: tag correct. Fix the problem by using the devres variant of mdiobus_register. Fixes: ba751e28 ("net: dsa: mt7530: add interrupt support") Signed-off-by:
-
Vladimir Oltean authored
As explained in commits: 74b6d7d1 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The Seville VSC9959 switch is a platform device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the seville switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The seville driver has a code structure that could accommodate both the mdiobus_unregister and mdiobus_free calls, but it has an external dependency upon mscc_miim_setup() from mdio-mscc-miim.c, which calls devm_mdiobus_alloc_size() on its behalf. So rather than restructuring that, and exporting yet one more symbol mscc_miim_teardown(), let's work with devres and replace of_mdiobus_register with the devres variant. When we use all-devres, we can ensure that devres doesn't free a still-registered bus (it either runs both callbacks, or none). Fixes: ac3a68d5 ("net: phy: don't abuse devres in devm_mdiobus_register()") Signed-off-by:
-
Vladimir Oltean authored
As explained in commits: 74b6d7d1 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The Felix VSC9959 switch is a PCI device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the felix switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The felix driver has the code structure in place for orderly mdiobus removal, so just replace devm_mdiobus_alloc_size() with the non-devres variant, and add manual free where necessary, to ensure that we don't let devres free a still-registered bus. Fixes: ac3a68d5 ("net: phy: don't abuse devres in devm_mdiobus_register()") Signed-off-by:
-
Vladimir Oltean authored
As explained in commits: 74b6d7d1 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The Starfighter 2 is a platform device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the bcm_sf2 switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The bcm_sf2 driver has the code structure in place for orderly mdiobus removal, so just replace devm_mdiobus_alloc() with the non-devres variant, and add manual free where necessary, to ensure that we don't let devres free a still-registered bus. Fixes: ac3a68d5 ("net: phy: don't abuse devres in devm_mdiobus_register()") Signed-off-by:
-
Vladimir Oltean authored
As explained in commits: 74b6d7d1 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The ar9331 is an MDIO device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the ar9331 switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The ar9331 driver doesn't have a complex code structure for mdiobus removal, so just replace of_mdiobus_register with the devres variant in order to be all-devres and ensure that we don't free a still-registered bus. Fixes: ac3a68d5 ("net: phy: don't abuse devres in devm_mdiobus_register()") Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
-
Vladimir Oltean authored
As explained in commits: 74b6d7d1 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The mv88e6xxx is an MDIO device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the Marvell switch driver on shutdown. systemd-shutdown[1]: Powering off. mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down fsl-mc dpbp.9: Removing from iommu group 7 fsl-mc dpbp.8: Removing from iommu group 7 ------------[ cut here ]------------ kernel BUG at drivers/net/phy/mdio_bus.c:677! Internal error: Oops - BUG: 0 [#1] PREEMPT SMP Modules linked in: CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15 pc : mdiobus_free+0x44/0x50 lr : devm_mdiobus_free+0x10/0x20 Call trace: mdiobus_free+0x44/0x50 devm_mdiobus_free+0x10/0x20 devres_release_all+0xa0/0x100 __device_release_driver+0x190/0x220 device_release_driver_internal+0xac/0xb0 device_links_unbind_consumers+0xd4/0x100 __device_release_driver+0x4c/0x220 device_release_driver_internal+0xac/0xb0 device_links_unbind_consumers+0xd4/0x100 __device_release_driver+0x94/0x220 device_release_driver+0x28/0x40 bus_remove_device+0x118/0x124 device_del+0x174/0x420 fsl_mc_device_remove+0x24/0x40 __fsl_mc_device_remove+0xc/0x20 device_for_each_child+0x58/0xa0 dprc_remove+0x90/0xb0 fsl_mc_driver_remove+0x20/0x5c __device_release_driver+0x21c/0x220 device_release_driver+0x28/0x40 bus_remove_device+0x118/0x124 device_del+0x174/0x420 fsl_mc_bus_remove+0x80/0x100 fsl_mc_bus_shutdown+0xc/0x1c platform_shutdown+0x20/0x30 device_shutdown+0x154/0x330 kernel_power_off+0x34/0x6c __do_sys_reboot+0x15c/0x250 __arm64_sys_reboot+0x20/0x30 invoke_syscall.constprop.0+0x4c/0xe0 do_el0_svc+0x4c/0x150 el0_svc+0x24/0xb0 el0t_64_sync_handler+0xa8/0xb0 el0t_64_sync+0x178/0x17c So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The Marvell driver already has a good structure for mdiobus removal, so just plug in mdiobus_free and get rid of devres. Fixes: ac3a68d5 ("net: phy: don't abuse devres in devm_mdiobus_register()") Reported-by:
Daniel Klauer <daniel.klauer@gin.de> Reviewed-by:
-
Mahesh Bandewar authored
When 803.2ad mode enables a participating port, it should update the slave-array. I have observed that the member links are participating and are part of the active aggregator while the traffic is egressing via only one member link (in a case where two links are participating). Via kprobes I discovered that slave-arr has only one link added while the other participating link wasn't part of the slave-arr. I couldn't see what caused that situation but the simple code-walk through provided me hints that the enable_port wasn't always associated with the slave-array update. Fixes: ee637714 ("bonding: Simplify the xmit function for modes that use xmit_hash") Signed-off-by:
Mahesh Bandewar <maheshb@google.com> Acked-by:
Jay Vosburgh <jay.vosburgh@canonical.com> Link: https://lore.kernel.org/r/20220207222901.1795287-1-maheshb@google.comSigned-off-by:
-
Tao Liu authored
This caused a significant performance degredation when using generic XDP with multiple queues. Fixes: f5cedc84 ("gve: Add transmit and receive support") Signed-off-by:
Tao Liu <xliutaox@google.com> Link: https://lore.kernel.org/r/20220207175901.2486596-1-jeroendb@google.comSigned-off-by:
-
- 08 Feb, 2022 1 commit
-
-
Pavel Parkhomenko authored
It is mandatory for a software to issue a reset upon modifying RGMII Receive Timing Control and RGMII Transmit Timing Control bit fields of MAC Specific Control register 2 (page 2, register 21) otherwise the changes won't be perceived by the PHY (the same is applicable for a lot of other registers). Not setting the RGMII delays on the platforms that imply it' being done on the PHY side will consequently cause the traffic loss. We discovered that the denoted soft-reset is missing in the m88e1121_config_aneg() method for the case if the RGMII delays are modified but the MDIx polarity isn't changed or the auto-negotiation is left enabled, thus causing the traffic loss on our platform with Marvell Alaska 88E1510 installed. Let's fix that by issuing the soft-reset if the delays have been actually set in the m88e1121_config_aneg_rgmii_delays() method. Cc: stable@vger.kernel.org Fixes: d6ab9336 ("net: phy: marvell: Avoid unnecessary soft reset") Signed-off-by:
Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru> Reviewed-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by:
Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20220205203932.26899-1-Pavel.Parkhomenko@baikalelectronics.ruSigned-off-by:
-
- 07 Feb, 2022 1 commit
-
-
Eric Dumazet authored
My last patch moved the netdev_tracker_alloc() call to a section protected by a write_lock(). I should have replaced GFP_KERNEL with GFP_ATOMIC to avoid the infamous: BUG: sleeping function called from invalid context at include/linux/sched/mm.h:256 Fixes: 28f92221 ("net/smc: fix ref_tracker issue in smc_pnet_add()") Signed-off-by:
-
