No functional changes

Add kernel doc for all ath5k_hw_* functions and strcucts. Also do some cleanup,
rename ath5k_hw_init_beacon to ath5k_hw_init_beacon_timers, remove an unused
variable from ath5k_hw_pcu_init and a few obsolete macros, mostly related to XR.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use usleep_range where possible to reduce busy waits
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Noise floor calibration does not interfere with traffic and should run more
often as part of our "short calibration". The full calibration is not the
noise floor calibration but the AGC + Gain_F (on RF5111 and RF5112) calibration
and should run less often because it does interfere with traffic.

So

Short calibration -> I/Q & NF Calibration
Long calibration -> Short + AGC + Gain_F

This patch was for some time on my pub/ dir on www.kernel.org and has been tested
by a few people and me. I think it's O.K. to go in.

I also changed ah_calibration to ah_iq_cal_needed to make more sense.

v2 Use a workqueue instead of a tasklet for calibration
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove unnecessary includes from base.h.  Add includes to other files as
necessary.  Don't include base.h unless needed.

Move declarations for functions in base.c from ath5k.h to base.h.

Use a better named define to protect base.h against double inclusion.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When checking for the band, use channel->band.

Change ath5k_hw_nic_wakeup() and ath5k_channel_ok() to take
ieee80211_channel.  Change ath5k_hw_radio_revision() to take
ieee80211_band.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

XR is a proprietary feature of the chipset.  It's not supported and
should not be supported.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Both ath5k_hw and ath5k_softc represent one instance of the hardware.
This duplication is historical and is not needed anymore.

Keep the name "ath5k_hw" for the merged structure and "ah" for the
variable pointing to it.  "ath5k_hw" is shorter than "ath5k_softc", more
descriptive and more widely used.

Put the combined structure to ath5k.h where the old ath5k_softc used to
be. Move some code from base.h to ath5k.h as needed.

Remove memory allocation for struct ath5k_hw and the corresponding error
handling.  Merge iobase and ah_iobase fields.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

AR2413 uses the same reference clock as AR5413
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Might fix some stability issues on newer chips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfgain probe is only necessary for OFDM operation on AR5111 and AR5112.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>

Fast channel change fixes:

a) Always set OFDM timings
b) Don't re-activate PHY
c) Enable only NF calibration, not AGC

https://bugzilla.kernel.org/show_bug.cgi?id=27382Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Correct channel setting function must be used for AR2317.
When I tested ahb patch on bullet2 all seemed to work fine,
but it couldn't connect another host (using ibss for example).
During an analysis I observed that it's transmitting on another
channel. I looked into madwifi code and understood that
the problem is in channel setting function. So atheros RF2317 not
fully handled in the current ath5k version and must be patched.
Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fast channel change fixes:

a) Always set OFDM timings
b) Don't re-activate PHY
c) Enable only NF calibration, not AGC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k_eeprom_mode_from_channel() returns -1 on error but we're storing
the result in "ee_mode" which is an unsigned char.  This breaks the
error handling.  This patch makes "ee_mode" an int.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Introduce a helper function to get the EEPROM mode from channel and remove
multiple similar switch statements. Also since it's now easy to get the EEPROM
mode from the channel, use them inside the functions which need it, instead of
passing a redundant ee_mode parameter.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove redundant defines.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a new variable to keep track of the currently configured tx power. Before
max_pwr was re-used for keeping the maximum allowed power as well as the
current configuration. Doing a min() on it allows you to lower the txpower, but
how would you be able to make it higher again?

This patch fixes that by adding a new variable ah_cur_pwr which is used instead
of txp_max_pwr to keep the current configuration. txp_max_pwr is used to check
if we are within the limits.

Another problem fixed by this patch is that it avoids setting a zero txpower
when things are initialized first and the current power is not yet set.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

And rename functions which write the powertable to make it clearer.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Let ath5k_hw_txpower() decide if it can re-use the powertable or if it has to
be recalculated instead of passing a 'fast' flag from the outside.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * By skipping tx power table calibration we also skip setting
 tx power table on hw. Make sure we always write tx power table
 on hw since it gets cleared on reset.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * A diff between rfbuffer settings of turbo and non-turbo
 modes indicates there is a bit on bank 2 related to turbo operation
 (it's set on turbo modes). This bit is present on all radios except
 RF5413 that seems to have a completely different bank 2. Also
 since 2317 has the same rf-registers locations with 2425 and
 since the bit exists on 2317 I assume it also exists on 2425/2417).
 So in case we use turbo mode (40MHz) enable it on bank modification.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Clean up CHANNEL_T(URBO), use AR5K_BWMODE_40MHZ instead
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Use correct clock value when setting OFDM timings on
 non-default bwmodes.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Don't return -EINVAL when trying to set tx power
 on RF5110 because AR5210 reset will fail. We need to
 add support for RF5110 and AR5210 eeprom in the future
 but for now just skip it.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Tweak phy activation -> rx delay for different bwmodes
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Add synth-only channel change for AR2413/5413. When we call
 ath5k_reset with a channel ath5k_hw_reset will first try to
 set channel on PHY while PHY is running instead of doing a normal
 full reset. To do this phy_init has to change to implement this
 functionality.

 * Clean up change_channel flag, what it really did was skip PCU
 registers when setting initvals. This is done because on reset
 PCU registers are not affected (except the registers we set
 in pcu init and -due to hw problems- TSF). Use a new skip_pcu
 flag that's not misleading instead. In the future we might use
 that to also skip PCU reset and save us the TSF etc problems
 (needs testing because standard practice is to reset everything).

 * Use fast channel change only when setting channel, and set skip_pcu
 to false only on init. When we reset the card due to DMA or PHY
 problems skip pcu but never do a fast channel change.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Only set power table if we are changing channel/mode
 there is no need to recalculate and reset the power table
 all the time.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Add spur mitigation filter support for half/quarter and turbo.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Tweak power detector delays on AR5111/AR5112 when
 using half/quarter modes.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Handle all usec parameters in one function. It's much cleaner
 this way.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Prepare for half/quarter/turbo support, introduce a new
 ah_bwmode parameter and get rid of ah_turbo. Bwmode stands
 for "bandwidth mode" and can have 4 values, default (20MHz),
 turbo (40MHz), half rate (10MHz), and quarter rate (5MHz).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * No functional changes

 * Clean up reset:
 Introduce init functions for each unit and call them instead
 of having everything inside ath5k_hw_reset (it's just c/p for
 now so nothing changes except calling order -I tested it with
 various cards and it's ok-)

 * Further cleanups:
 ofdm_timings belongs to phy.c
 rate_duration belongs to pcu.c
 clock functions are general and belong to reset.c (more to follow)

 * Reorder functions for better organization:
 We start with helpers and other functions follow in categories,
 init functions are last
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch moves code out from wireless drivers where two different
functions are defined in three code locations for the same purpose and
provides a common function to sign extend a 32-bit value.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As reported by Ryan Niemi, some bitmasks in the register definition for the PCU
Diagnostic register (DIAG_SW) were missing a zero at the end. While at it fix
some typos and add more comments.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>