Define some simple helper functions for adding and deleting entries on the
expiring dentry list.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Sage Weil <sage@newdream.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Yehuda Saheh <yehuda@newdream.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Define some simple helper functions for adding and deleting entries on the
active (and unhashed) dentry list.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Sage Weil <sage@newdream.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Yehuda Saheh <yehuda@newdream.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

For embedded systems, the blinking cursor at startup time can be annoying
and unintended.  Add a new kernel parameter to change the default cursor
shape.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: David Newall <davidn@davidnewall.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* de_get() is trivial -- make inline, save a few bits of code, drop
  "refcount is 0" check -- it should be done in some generic refcount
  code, don't recall it's was helpful

* rename GET and PUT functions to pde_get(), pde_put() for cool prefix!

* remove obvious and incorrent comments

* in remove_proc_entry() use pde_put(), when I fixed PDE refcounting to
  be normal one, remove_proc_entry() was supposed to do "-1" and code now
  reflects that.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ktime will overflow from 03:14:07 UTC on Tuesday, 19 January 2038,
ktime_add() in timecompare_update() will overflow a half earlier.  As a
result, wrong offset will be gotten, then cause some strange problems.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Patrick Ohly <patrick.ohly@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix node-oriented allocation handling in oom-kill.c I myself think of this
as a bugfix not as an ehnancement.

In these days, things are changed as
  - alloc_pages() eats nodemask as its arguments, __alloc_pages_nodemask().
  - mempolicy don't maintain its own private zonelists.
  (And cpuset doesn't use nodemask for __alloc_pages_nodemask())

So, current oom-killer's check function is wrong.

This patch does
  - check nodemask, if nodemask && nodemask doesn't cover all
    node_states[N_HIGH_MEMORY], this is CONSTRAINT_MEMORY_POLICY.
  - Scan all zonelist under nodemask, if it hits cpuset's wall
    this faiulre is from cpuset.
And
  - modifies the caller of out_of_memory not to call oom if __GFP_THISNODE.
    This doesn't change "current" behavior. If callers use __GFP_THISNODE
    it should handle "page allocation failure" by itself.

  - handle __GFP_NOFAIL+__GFP_THISNODE path.
    This is something like a FIXME but this gfpmask is not used now.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hioryu@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In a typical oom analysis scenario, we frequently want to know whether the
killed process has a memory leak or not at the first step.  This patch
adds vsz and rss information to the oom log to help this analysis.  To
save time for the debugging.

example:
===================================================================
rsyslogd invoked oom-killer: gfp_mask=0x201da, order=0, oom_adj=0
Pid: 1308, comm: rsyslogd Not tainted 2.6.32-rc6 #24
Call Trace:
[<ffffffff8132e35b>] ?_spin_unlock+0x2b/0x40
[<ffffffff810f186e>] oom_kill_process+0xbe/0x2b0

(snip)

492283 pages non-shared
Out of memory: kill process 2341 (memhog) score 527276 or a child
Killed process 2341 (memhog) vsz:1054552kB, anon-rss:970588kB, file-rss:4kB
===========================================================================
                             ^
                             |
                            here

[rientjes@google.com: fix race, add pid & comm to message]
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Caused by commit 0b83ddeb ("MFD:
twl4030: add twl4030_codec MFD as a new child to the core") interacting
with commit b07682b6 ("mfd: Rename
twl4030* driver files to enable re-use").

This file seems to have been missed in the renaming.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: event tracing support
  xfs: change the xfs_iext_insert / xfs_iext_remove
  xfs: cleanup bmap extent state macros

* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (80 commits)
  dm snapshot: use merge origin if snapshot invalid
  dm snapshot: report merge failure in status
  dm snapshot: merge consecutive chunks together
  dm snapshot: trigger exceptions in remaining snapshots during merge
  dm snapshot: delay merging a chunk until writes to it complete
  dm snapshot: queue writes to chunks being merged
  dm snapshot: add merging
  dm snapshot: permit only one merge at once
  dm snapshot: support barriers in snapshot merge target
  dm snapshot: avoid allocating exceptions in merge
  dm snapshot: rework writing to origin
  dm snapshot: add merge target
  dm exception store: add merge specific methods
  dm snapshot: create function for chunk_is_tracked wait
  dm snapshot: make bio optional in __origin_write
  dm mpath: reject messages when device is suspended
  dm: export suspended state to targets
  dm: rename dm_suspended to dm_suspended_md
  dm: swap target postsuspend call and setting suspended flag
  dm crypt: add plain64 iv
  ...

* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block:
  cfq: set workload as expired if it doesn't have any slice left
  Fix a CFQ crash in "for-2.6.33" branch of block tree
  cfq: Remove wait_request flag when idle time is being deleted
  cfq-iosched: commenting non-obvious initialization
  cfq-iosched: Take care of corner cases of group losing share due to deletion
  cfq-iosched: Get rid of cfqq wait_busy_done flag
  cfq: Optimization for close cooperating queue searching
  block,xd: Delay allocation of DMA buffers until device is known
  drbd: Following the hmac change to SHASH (see linux commit 8bd1209c)
  cfq-iosched: reduce write depth only if sync was delayed

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: ac97_codec - increase timeout for analog sections to 5 second
  ASoC: Correct code taking the size of a pointer
  ALSA: hda - Add PCI IDs for Nvidia G2xx-series
  ALSA: sound/isa/gus: Correct code taking the size of a pointer
  ALSA: hda: Fix max PCM level to 0 dB for AD1981_HP
  ALSA: hda: Use ALC260_WILL quirk for another Acer model (0x1025007f)

Merge branch 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (26 commits)
  clockevents: Convert to raw_spinlock
  clockevents: Make tick_device_lock static
  debugobjects: Convert to raw_spinlocks
  perf_event: Convert to raw_spinlock
  hrtimers: Convert to raw_spinlocks
  genirq: Convert irq_desc.lock to raw_spinlock
  smp: Convert smplocks to raw_spinlocks
  rtmutes: Convert rtmutex.lock to raw_spinlock
  sched: Convert pi_lock to raw_spinlock
  sched: Convert cpupri lock to raw_spinlock
  sched: Convert rt_runtime_lock to raw_spinlock
  sched: Convert rq->lock to raw_spinlock
  plist: Make plist debugging raw_spinlock aware
  bkl: Fixup core_lock fallout
  locking: Cleanup the name space completely
  locking: Further name space cleanups
  alpha: Fix fallout from locking changes
  locking: Implement new raw_spinlock
  locking: Convert raw_rwlock functions to arch_rwlock
  locking: Convert raw_rwlock to arch_rwlock
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  avr32: update default configurations for ATNGW100, ATSTK1002 and ATSTK1006
  avr32: add default configurations for ATNGW100 mkII and EVKLCD10X
  avr32: add support for ATNGW100 mkII board
  avr32: convert to asm-generic/hardirq.h
  avr32: add two new at91 to cpu.h definition
  avr32: clean up linker script using standard macros.
  avr32: MRMT: correct setup of SPI slaves
  avr32: function for independently setting up SPI slaves
  avr32: re-instate MCI WP/CD pin assignments for ATNGW100

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix clock event multiplier printf format.
  sparc64: Use clock{source,events}_calc_mult_shift().
  sparc64: Use free_bootmem_late() in mdesc_lmb_free().
  sparc: Add alignment and emulation fault perf events.
  sparc64: Add syscall tracepoint support.
  sparc: Stop trying to be so fancy and use __builtin_{memcpy,memset}()
  sparc: Use __builtin_object_size() to validate the buffer size for copy_from_user()
  sparc64: Add some missing __kprobes annotations to kernel fault paths.
  sparc64: Use kprobes_built_in() to avoid ifdefs in fault_64.c
  sparc: Validate that kprobe address is 4-byte aligned.
  sparc64: Don't specify IRQF_SHARED for LDC interrupts.
  sparc64: Fix stack debugging IRQ stack regression.
  sparc64: Fix overly strict range type matching for PCI devices.

* git://git.infradead.org/battery-2.6:
  power_supply_sysfs: Handle -ENODATA in a special way
  wm831x_backup: Remove unused variables
  gta02: Set pcf50633 charger_reference_current_ma
  pcf50633: Query charger status directly
  pcf50633: Properly reenable charging when the supply conditions change
  pcf50633: Get rid of charging restart software auto-triggering
  pcf50633: introduces battery charging current control
  pcf50633: Add ac power supply class to the charger
  wm831x: Factor out WM831x backup battery charger

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: Close usb_find_interface race v3
  Revert "USB: Close usb_find_interface race"

[akpm@linux-foundation.org: s/q/g/ (Randy)]
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Report output values as 1/1000 of earth gravity.

Output values from lis3 can be read from sysfs position entry and from
input device.  Input device can be accessed as event device and as
joystick device.  Joystick device can be in two modes.  Meaning of the
output values varies from case to case depending on the chip type and
configuration (scale).  Only joystick interface in JS_CORR_BROKEN mode
returned somehow similar output values in different configurations.
Joystick device is in that state by default in case of lis3.

Position sysfs entry, input event device and raw joystick device have been
little bit broken since meaning of the output values has been varied
between 12 and 8 bit devices.  Applications which relayed on those methods
failed if the chip is different than the expected one.

This patch converts output values to mean similar thing in different
configurations.  Both 8 and 12 bit devices reports now same acceleration
values.  If somebody implements full scale support to the driver, output
values will still mean the same.  Scaling factor and input device range
must be updated in that case.

Joystick interface in JS_CORR_BROKEN mode is not touched by this patch.
All other interfaces have different scale after this change.  For 12 bit
device scaling factor is 0.977 which keeps scaled and unscaled values are
quite close to each others.  For 8 bit device, scaled values are 18 times
bigger than unscaled values.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It is possible to read position information at the chip measurement rate
via sysfs.  This patch adds possibility to configure chip measurement
rate.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Chip is calibrated by the manufacturer.  There is no need to calibarate it
at driver level.  If the chip is used as a joystick, calibaration can be
done using joystick device calibration mechanism.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Implement selftest feature as specified by chip manufacturer.  Control:
read selftest sysfs entry

Response: "OK x y z" or "FAIL x y z"

where x, y, and z are difference between selftest mode and normal mode.
Test is passed when values are within acceptance limit values.

Acceptance limits are provided via platform data.  See chip spesifications
for acceptance limits.  If limits are not properly set, OK / FAIL decision
is meaningless.  However, userspace application can still make decision
based on the numeric x, y, z values.

Selftest is meant for HW diagnostic purposes.  It is not meant to be
called during normal use of the chip.  It may cause false interrupt
events.  Selftest mode delays polling of the normal results but it doesn't
cause wrong values.  Chip must be in static state during selftest.  Any
acceration during the test causes most probably failure.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Lis3 accelerometer sensors have quite long power on delay (up to 125
ms). This patch adds necessary delay to power on sequence for currently
supported lis3 chips.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Originally the driver was only targeted to 12bits sensors.  When support
for 8bits sensors was added, some slight difference in the registers were
overlooked.  This should fix it, both for initialization, and for
displaying the rate.
Reported-by: Kalhan Trisal <kalhan.trisal@intel.com>
Reported-by: Christoph Plattner <christoph.plattner@gmx.at>
Tested-by: Christoph Plattner <christoph.plattner@gmx.at>
Tested-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Most of the documentation and comments were written when the driver was
only supporting one type of chip, only via ACPI/HP. Update the info to
the much clearer understanding that we have now.
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

polled input device itself was not free'd.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Send input_sync after each measurement round. This helps userspace to
detect which reported values belongs to the same measurement.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add control of fan minimum turn-on output levels, decoupling it from the
fan turn-off output level.  Add control of rate of change of fan output
level.  These in turn allow lower turn-off rotor speed and smoother
transitions for better thermal and acoustic control authority.  Add
support for constant fan speed and proportional-response operations modes.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Hubbard <david.c.hubbard@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add the possibility to remap axes via platform data.  Function pointers
for resource setup and release purposes
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Jean Delvare <khali@linux-fr.org>
Cc:  "Trisal, Kalhan" <kalhan.trisal@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Move common crc body to new function crc32_body() cleaup and micro
optimize crc32_body for speed and less size.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Improve the /proc/interrupts output so the irq number can be mapped to
platform device on boards with multiple tmio_mmc instances.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: <linux-mmc@vger.kernel.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add SD host driver for Blackfin BF54x and BF51x.

[akpm@linux-foundation.org: fix layout, c99 warning]
Signed-off-by: Cliff Cai <cliffcai.sh@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This new revision of the IP adds some improvements to the MCI already
present in several Atmel SOC.

Some new registers are added and a particular way of handling DMA
interaction lead to a new sequence in function call which is backward
compatible: On MCI2, we must set the DMAEN bit to enable the DMA
handshaking interface.  This must happen before the data transfer command
is sent.

A new function is able to differentiate MCI2 code and is based on
knowledge of processor id (cpu_is_xxx()).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Allow the use of another DMA controller driver in atmel-mci sd/mmc driver.
 This adds a generic dma_slave pointer to the mci platform structure where
we can store DMA controller information.  In atmel-mci we use information
provided by this structure to initialize the driver (with new helper
functions that are architecture dependant).

This also adds at32/avr32 chip modifications to cope with this new access
method.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Some people run general-purpose distribution kernels on netbooks with
a card that is physically non-removable or logically non-removable
(e.g. used for /home) and cannot be cleanly unmounted during suspend.
Add a module parameter to set whether cards are assumed removable or
non-removable, with the default set by CONFIG_MMC_UNSAFE_RESUME.

In general, it is not possible to tell whether a card present in an MMC
slot after resume is the same that was there before suspend.  So there are
two possible behaviours, each of which will cause data loss in some cases:

CONFIG_MMC_UNSAFE_RESUME=n (default): Cards are assumed to be removed
during suspend.  Any filesystem on them must be unmounted before suspend;
otherwise, buffered writes will be lost.

CONFIG_MMC_UNSAFE_RESUME=y: Cards are assumed to remain present during
suspend.  They must not be swapped during suspend; otherwise, buffered
writes will be flushed to the wrong card.

Currently the choice is made at compile time and this allows that to be
overridden at module load time.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Wouter van Heyst <larstiq@larstiq.dyndns.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Convert two missed s3c2410 specific gpio calls to gpiolib calls.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is still in use especially to develop SDIO device drivers on laptop
machines which are lacking SDIO slots.  This adapter supports SDIO cards
only due to lack of 136-bit response capability.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove check for host->iclk being NULL from error path since we already
know it is non-null and use return value from clk_get.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add cpufreq support to MMC driver. The clock divider value has to be
modified according to the controller input frequency.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Cc: Linus Walleij <linus.ml.walleij@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently DaVinci EDMA driver supports multiple EDMA channel controller
instances.  edma_alloc_channel() api returns a 32 bit value which has the
channel controller number in MSB and the EDMA channel number in LSB.  The
variables which store the value returned by edma_alloc_channel() have to
be 32 bit wide now.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Vipin Bhandari <vipin.bhandari@ti.com>
Cc: Purshotam Kumar <purushotam@ti.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>