Microchip PDMC IP doesn't filter microphone noises on startup. By default,
it captures data received from digital microphones after
the MCHP_PDMC_MR.EN bits are set. Thus when enable is set on PDMC side the
digital microphones might not be ready yet and PDMC captures data from then
in this time. This data captured is poc noise. To avoid this the software
workaround is to the following:
1/ enable PDMC channel
2/ wait 150ms (on SAMA7G5-EK setup)
3/ execute 16 dummy reads from RHR
4/ clear interrupts
5/ enable interrupts
6/ enable DMA channel

Fixes: 50291652 ("ASoC: atmel: mchp-pdmc: add PDMC driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230228110145.3770525-4-claudiu.beznea@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

PDMC can work with different types of microphones, thus different boards
could have different microphones. Depending on microphone type the PDMC
would need to wait longer or shorter period (at startup) than the default
chosen one to filter unwanted noise. Thus add microchip,startup-delay-us
binding to let PDMC users to specify startup delay.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230228110145.3770525-3-claudiu.beznea@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add option to start DMA component after DAI trigger. This is done
by filling the new struct snd_soc_component_driver::start_dma_last.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230228110145.3770525-2-claudiu.beznea@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

When we fail to obtain a DMA channel, don't return a blanket -EINVAL,
instead return the original error code if there's one. This makes
deferring work as it should. Also don't print an error message for
-EPROBE_DEFER.

Fixes: 4ec8179c ("ASoC: apple: mca: Postpone requesting of DMA channels")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20230224153302.45365-3-povik+lin@cutebit.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fix the reset sequence of reads and writes that we invoke from within
the early trigger. It looks like there never was a SERDES_CONF_SOME_RST
bit that should be involved in the reset sequence, and its presence in
the driver code is a mistake from earlier.

Instead, the reset sequence should go as follows: We should switch the
the SERDES unit's SYNC_SEL mux to the value of 7 (so outside the range
of 1...6 representing cluster's SYNCGEN units), then raise the RST bit
in SERDES_STATUS and wait for it to clear.

Properly resetting the SERDES unit fixes frame desynchronization hazard
in case of long frames (longer than 4 used slots). The desynchronization
manifests itself by rotating the PCM channels.

Fixes: 3df5d0d9 ("ASoC: apple: mca: Start new platform driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20230224153302.45365-2-povik+lin@cutebit.orgSigned-off-by: Mark Brown <broonie@kernel.org>

From within the early trigger we are doing a reset of the SERDES unit,
but the final status read is on a bad address. Add the missing SERDES
unit offset in calculation of the address.

Fixes: 3df5d0d9 ("ASoC: apple: mca: Start new platform driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20230224153302.45365-1-povik+lin@cutebit.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The regulators are supposed to be controlled through the
set_bias_level() component callback. Moreover, the regulators are not
enabled during probe and so, this would lead to a regulator unbalanced
use count.

Fixes: ca514c0f ("ASOC: Add ADAU7118 8 Channel PDM-to-I2S/TDM Converter driver")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230224104551.1139981-1-nuno.sa@analog.comSigned-off-by: Mark Brown <broonie@kernel.org>

The block found on Apple's M2 SoC is compatible with the existing driver
so add its per-SoC compatible.
Signed-off-by: Janne Grunau <j@jannau.net>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20230202-asahi-t8112-dt-v1-14-cb5442d1c229@jannau.netSigned-off-by: Mark Brown <broonie@kernel.org>

Add mtl_mx98360a_rt5682 driver data for Chrome Rex board support.
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230220080652.23136-1-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

In mt8188_etdm_clk_src_sel_put() function, val retrieved by FIELD_PREP
is shifted to the corresponding bit filed, so it can compare with the
register value directly.

Originally, the redundant bit shift of the register value results in
the wrong comparison result, so we remove bit shift operation in the
patch.

Fixes: 2babb477 ("ASoC: mediatek: mt8188: support etdm in platform driver")
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Link: https://lore.kernel.org/r/20230215125017.16044-1-trevor.wu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

This device can output mono, left or right.
LR data should be swapped to output right data.
Signed-off-by: Kiseok Jo <kiseok.jo@irondevice.com>
Link: https://lore.kernel.org/r/20230217004403.10220-1-kiseok.jo@irondevice.comSigned-off-by: Mark Brown <broonie@kernel.org>

Enables display microphone on the HP OMEN 16z-n000 (8A42) laptop
Signed-off-by: Joseph Hunkeler <jhunkeler@gmail.com>
Link: https://lore.kernel.org/r/20230216155007.26143-1-jhunkeler@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

"BRG" stands for "Baud Rate Generator", but is frequently misspelled as
"RBG".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/ac6365c17861d71fbc89d823089db4aafdb763ed.1676470202.git.geert+renesas@glider.beSigned-off-by: Mark Brown <broonie@kernel.org>

Remove the sleep control in IRQ thread
and create an individual task to handel it for Jack plug in event.

This commit improves the control of ground switches in the AAD IRQ.
Signed-off-by: David Rau <David.Rau.opensource@dm.renesas.com>
Link: https://lore.kernel.org/r/20230215101045.21456-1-David.Rau.opensource@dm.renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

With the switching to dev_err_probe(), during the conversion
of GPIO calls, the return code is passed is a paratemer to it.
At the same time a copy'n'paste mistake was made, so the wrong
variable has been taken for the error reporting. Fix this.

Fixes: 3ee0d39c ("ASoC: soc-ac97: Convert to agnostic GPIO API")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230215132343.35547-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add struct snd_pcm_substream forward declaration

Fixes: 078a85f2 ("ASoC: dapm: Only power up active channels from a DAI")
Signed-off-by: Lucas Tanure <lucas.tanure@collabora.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230215132851.1626881-1-lucas.tanure@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

Now tables isn't a separate module, definitely no need to have a
separate namespace for it.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230215105818.3315925-2-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

There is no reason to have a separate module for the tables file it just
holds regmap callbacks and register patches used by the main part of the
driver. Remove the separate module and merge it into the main driver
module.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230215105818.3315925-1-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The of_gpio.h is going to be removed. In preparation of that convert
the driver to the agnostic API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230213161713.1450-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

SSI is supporting both "PIO mode" and "DMA mode", thus "dmas/dma-names"
are not mandatory property. Drop these from rcar_sound,ssi's required:.
This is prepare for Gen4 support. See more details on Link

Link: https://lore.kernel.org/all/87zg9vk0ex.wl-kuninori.morimoto.gx@renesas.com/#r
Link: https://lore.kernel.org/all/87r0v2uvm7.wl-kuninori.morimoto.gx@renesas.com/#r
Link: https://lore.kernel.org/all/87r0v1t02h.wl-kuninori.morimoto.gx@renesas.com/#r
Link: https://lore.kernel.org/all/87y1p7bpma.wl-kuninori.morimoto.gx@renesas.com/#rSigned-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87r0uu8g8x.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:

The following series will enable the the Low Power Audio (LPA)
playback on Intel platforms when using IPC4.

The support is closely follows how IPC3 supports similar use case.

All depending patches are upstream and our CI have been testing
this feature for some time without issues.

Simplify code by using min helper macro for logical evaluation and value
assignment. The change also facilitates code realignment for improved
readability.
Proposed change is identified using minmax.cocci Coccinelle script.
Signed-off-by: Deepak R Varma <drv@mailo.com>
Link: https://lore.kernel.org/r/Y+p2Hn0nrtHiKwPR@ubun2204.myguest.virtualbox.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The kernel is globally removing the ambiguous 0-length and 1-element
arrays in favor of flexible arrays, so that we can gain both compile-time
and run-time array bounds checking[1]. In this instance, struct
skl_cpr_cfg contains struct skl_cpr_gtw_cfg, which defined "config_data"
as a 1-element array.

However, case present in sound/soc/intel/skylake/skl-topology.h is not a
simple one as the structure takes part in IPC communication. Apparently
original definition missed one field, which while not used by AudioDSP
firmware when there is no additional data, is still expected to be part
of an IPC message. Currently this works because of how 'config_data' is
declared: 'config_data[1]'. Now when one replaces it with a flexible
array there would be one field missing. Update struct declaration to fix
this.
Reported-by: Sasa Ostrouska <casaxa@gmail.com>
Link: https://lore.kernel.org/all/CALFERdwvq5day_sbDfiUsMSZCQu9HG8-SBpOZDNPeMdZGog6XA@mail.gmail.com/
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Cc: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: alsa-devel@alsa-project.org
CC: Kees Cook <keescook@chromium.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230213205223.2679357-1-amadeuszx.slawinski@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The 'tlv320adcx140' driver currently supports 3 devices: TLV320ADC3140,
TLV320ADC5140 and TLV320ADC6140.

All 3 devices, support higher samplerates, up to 768-kHz according to their
datasheets.

In our applications, we only tested (and worked) with 96 kHz and 192 kHz.

This change extends the list of supported sample-rates for these devices
with 96 & 192 kHz.

References:
  https://www.ti.com/product/TLV320ADC3140
  https://www.ti.com/product/TLV320ADC5140
  https://www.ti.com/product/TLV320ADC6140Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230214091051.16323-1-alex@shruggie.roSigned-off-by: Mark Brown <broonie@kernel.org>

Variable ret is initialed but is never modified or used except for
returning the initial value 0. The value can be directly returned
instead and the variable definition can be dropped.
Issue identified using returnvar.cocci Coccinelle semantic patch.
Signed-off-by: Deepak R Varma <drv@mailo.com>
Link: https://lore.kernel.org/r/Y+p9r5y9DPSJkPVf@ubun2204.myguest.virtualbox.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The rt5682s driver switches its regmap to cache-only when the
device suspends and back to regular mode on resume. When the
jack detect interrupt fires rt5682s_irq() schedules the jack
detect work. This can result in invalid reads from the regmap
in cache-only mode if the work runs before the device has
resumed:

[   19.672162] rt5682s 2-001a: ASoC: error at soc_component_read_no_lock on rt5682s.2-001a for register: [0x000000f0] -16

Disable the jack detection interrupt during suspend and
re-enable it on resume. The driver already schedules the
jack detection work on resume, so any state change during
suspend is still handled.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20230209012002.1.Ib4d6481f1d38a6e7b8c9e04913c02ca88c216cf6@changeidSigned-off-by: Mark Brown <broonie@kernel.org>

Enable d0i3 streaming if all the active streams can
work in d0i3 state and playback is enabled.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-6-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Schedule a delayed work for d0i3 entry after every non-pm ipc msg.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-5-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The driver shall update the power state to D0i0 before sending
a generic IPC. Power-related IPCs are the exception to the rule,
they may be sent even when the power-state is D0i3
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-4-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Use set_pm_gate to unify pm gate setting for different
ipc version.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-3-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Set_pm_gate depends on ipc version. This patch defines
the ops for both IPC3 and IPC4.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-2-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

./sound/soc/codecs/peb2466.c:1851:2-3: Unneeded semicolon
./sound/soc/codecs/peb2466.c:1887:2-3: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4045Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230213010547.105312-1-yang.lee@linux.alibaba.comSigned-off-by: Mark Brown <broonie@kernel.org>

When the 'ti,gpio-config' property is not defined, the
device_property_count_u32() will return an error, rather than zero.

The current check, only handles a return value of zero, which assumes that
the property is defined and has nothing defined.

This change extends the check to also check for an error case (most likely
to be hit by the case that the 'ti,gpio-config' is not defined).

In case that the 'ti,gpio-config' and the returned 'gpio_count' is not
correct, there is a 'if (gpio_count != ADCX140_NUM_GPIO_CFGS)' check, a few
lines lower that will return -EINVAL.
This means that someone tried to define 'ti,gpio-config', but with the
wrong number of GPIOs.

Fixes: d5214321 ("ASoC: tlv320adcx140: Add support for configuring GPIO pin")
Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230213073805.14640-1-alex@shruggie.roSigned-off-by: Mark Brown <broonie@kernel.org>

Add select GPIOLIB to the sound/soc/codecs/Kconfig file
Signed-off-by: Ben Yi <yijiangtao@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230213093649.22928-4-wangweidong.a@awinic.comSigned-off-by: Mark Brown <broonie@kernel.org>

Change hdrlen to hdr_len
Signed-off-by: Ben Yi <yijiangtao@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230213093649.22928-3-wangweidong.a@awinic.comSigned-off-by: Mark Brown <broonie@kernel.org>

Change the function name aw88395_plack_event to aw88395_playback_event
Signed-off-by: Ben Yi <yijiangtao@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230213093649.22928-2-wangweidong.a@awinic.comSigned-off-by: Mark Brown <broonie@kernel.org>

Convert the Maxim Integrated MAX98095 audio codec bindings to DT schema.
Add missing sound-dai-cells during conversion.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230211134755.86061-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Commit 2458adb8
("SoC: simple-card-utils: set 0Hz to sysclk when shutdown")
added a call to snd_soc_dai_set_sysclk() with 0 Hz frequency. Being
propagated further it causes a division by zero in clk-ep93xx driver:

Division by zero in kernel.
CPU: 0 PID: 52 Comm: aplay Tainted: G        W          6.2.0-rc4-... #1
Hardware name: Generic DT based system
 unwind_backtrace from show_stack+0x10/0x18
 show_stack from dump_stack_lvl+0x28/0x34
 dump_stack_lvl from __div0+0x10/0x1c
 __div0 from Ldiv0+0x8/0x1c
 Ldiv0 from ep93xx_mux_determine_rate+0x78/0x1d0
 ep93xx_mux_determine_rate from clk_core_round_rate_nolock+0x48/0xc8
 clk_core_round_rate_nolock from clk_core_set_rate_nolock+0x48/0x160
 clk_core_set_rate_nolock from clk_set_rate+0x30/0x8c
 clk_set_rate from ep93xx_i2s_set_sysclk+0x30/0x6c
 ep93xx_i2s_set_sysclk from snd_soc_dai_set_sysclk+0x3c/0xa4
 snd_soc_dai_set_sysclk from asoc_simple_shutdown+0xb8/0x164
 asoc_simple_shutdown from snd_soc_link_shutdown+0x44/0x54
 snd_soc_link_shutdown from soc_pcm_clean+0x78/0x180
 soc_pcm_clean from soc_pcm_close+0x28/0x40
 soc_pcm_close from snd_pcm_release_substream.part.0+0x3c/0x84
 snd_pcm_release_substream.part.0 from snd_pcm_release+0x40/0x88
 snd_pcm_release from __fput+0x74/0x278

There has been commit f1879d7b ("ASoC: rockchip: ignore 0Hz sysclk"),
but it prepared by far not all drivers.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230212220923.258414-1-alexander.sverdlin@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch fixes
1. coding style issues
2. check if the setting was set already in rt712_sdca_mux_put callback
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20230210082141.24077-1-shumingf@realtek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Current rsnd silently uses default TDM width if it was strange
settings. It is difficult to notice about it.
This patch indicates warning for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lel6ksqn.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>