Some TI chips raise the DMA complete interrupt before the actual
transfer has been completed. The code tries to busy wait for a few
microseconds and if that fails it arms an hrtimer to recheck. So far
so good, but that has the following issue:

CPU 0					CPU1

start_next_transfer(RQ1);

DMA interrupt
  if (premature_irq(RQ1))
    if (!hrtimer_active(timer))
       hrtimer_start(timer);

hrtimer expires
  timer->state = CALLBACK_RUNNING;
  timer->fn()
    cppi41_recheck_tx_req()
      complete_request(RQ1);
      if (requests_pending())
        start_next_transfer(RQ2);

					DMA interrupt
					  if (premature_irq(RQ2))
					    if (!hrtimer_active(timer))
					       hrtimer_start(timer);
  timer->state = INACTIVE;

The premature interrupt of request2 on CPU1 does not arm the timer and
therefor the request completion never happens because it checks for
!hrtimer_active(). hrtimer_active() evaluates:

  timer->state != HRTIMER_STATE_INACTIVE

which of course evaluates to true in the above case as timer->state is
CALLBACK_RUNNING.

That's clearly documented:

 * A timer is active, when it is enqueued into the rbtree or the
 * callback function is running or it's in the state of being migrated
 * to another cpu.

But that's not what the code wants to check. The code wants to check
whether the timer is queued, i.e. whether its armed and waiting for
expiry.

We have a helper function for this: hrtimer_is_queued(). This
evaluates:

  timer->state & HRTIMER_STATE_QUEUED

So in the above case this evaluates to false and therefor forces the
DMA interrupt on CPU1 to call hrtimer_start().

Use hrtimer_is_queued() instead of hrtimer_active() and evrything is
good.
Reported-by: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>

The value 0x3 (not 0x11) in the field for additional transaction/microframe
is reserved and should not be let through. Be clear in the error message about
what value caused the error return.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

At probe time, the musb_am335x driver register its childs by
calling of_platform_populate(), which registers all childs in
the devicetree hierarchy recursively.

On the other side, the driver's remove() function uses of_device_unregister()
to remove each child of musb_am335x's.

However, when musb_dsps is loaded, its devices are attached to the musb_am335x
device as musb_am335x childs. Hence, musb_am335x remove() will attempt to
unregister the devices registered by musb_dsps, which produces a kernel panic.

In other words, the childs in the "struct device" hierarchy are not the same
as the childs in the "devicetree" hierarchy.

Ideally, we should enforce the removal of the devices registered by
musb_am335x *only*, instead of all its child devices. However, because of the
recursive nature of of_platform_populate, this doesn't seem possible.

Therefore, as the only solution at hand, this commit disables musb_am335x
driver removal capability, preventing it from being ever removed. This was
originally suggested by Sebastian Siewior:

https://www.mail-archive.com/linux-omap@vger.kernel.org/msg104946.html

And for reference, here's the panic upon module removal:

musb-hdrc musb-hdrc.0.auto: remove, state 4
usb usb1: USB disconnect, device number 1
musb-hdrc musb-hdrc.0.auto: USB bus 1 deregistered
Unable to handle kernel NULL pointer dereference at virtual address 0000008c
pgd = de11c000
[0000008c] *pgd=9e174831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] ARM
Modules linked in: musb_am335x(-) musb_dsps musb_hdrc usbcore usb_common
CPU: 0 PID: 623 Comm: modprobe Not tainted 3.15.0-rc4-00001-g24efd13 #69
task: de1b7500 ti: de122000 task.ti: de122000
PC is at am335x_shutdown+0x10/0x28
LR is at am335x_shutdown+0xc/0x28
pc : [<c0327798>]    lr : [<c0327794>]    psr: a0000013
sp : de123df8  ip : 00000004  fp : 00028f00
r10: 00000000  r9 : de122000  r8 : c000e6c4
r7 : de0e3c10  r6 : de0e3800  r5 : de624010  r4 : de1ec750
r3 : de0e3810  r2 : 00000000  r1 : 00000001  r0 : 00000000
Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c5387d  Table: 9e11c019  DAC: 00000015
Process modprobe (pid: 623, stack limit = 0xde122240)
Stack: (0xde123df8 to 0xde124000)
3de0:                                                       de0e3810 bf054488
3e00: bf05444c de624010 60000013 bf043650 000012fc de624010 de0e3810 bf043a20
3e20: de0e3810 bf04b240 c0635b88 c02ca37c c02ca364 c02c8db0 de1b7500 de0e3844
3e40: de0e3810 c02c8e28 c0635b88 de02824c de0e3810 c02c884c de0e3800 de0e3810
3e60: de0e3818 c02c5b20 bf05417c de0e3800 de0e3800 c0635b88 de0f2410 c02ca838
3e80: bf05417c de0e3800 bf055438 c02ca8cc de0e3c10 bf054194 de0e3c10 c02ca37c
3ea0: c02ca364 c02c8db0 de1b7500 de0e3c44 de0e3c10 c02c8e28 c0635b88 de02824c
3ec0: de0e3c10 c02c884c de0e3c10 de0e3c10 de0e3c18 c02c5b20 de0e3c10 de0e3c10
3ee0: 00000000 bf059000 a0000013 c02c5bc0 00000000 bf05900c de0e3c10 c02c5c48
3f00: de0dd0c0 de1ec970 de0f2410 bf05929c de0f2444 bf05902c de0f2410 c02ca37c
3f20: c02ca364 c02c8db0 bf05929c de0f2410 bf05929c c02c94c8 bf05929c 00000000
3f40: 00000800 c02c8ab4 bf0592e0 c007fc40 c00dd820 6273756d 336d615f 00783533
3f60: c064a0ac de1b7500 de122000 de1b7500 c000e590 00000001 c000e6c4 c0060160
3f80: 00028e70 00028e70 00028ea4 00000081 60000010 00028e70 00028e70 00028ea4
3fa0: 00000081 c000e500 00028e70 00028e70 00028ea4 00000800 becb59f8 00027608
3fc0: 00028e70 00028e70 00028ea4 00000081 00000001 00000001 00000000 00028f00
3fe0: b6e6b6f0 becb59d4 000160e8 b6e6b6fc 60000010 00028ea4 00000000 00000000
[<c0327798>] (am335x_shutdown) from [<bf054488>] (dsps_musb_exit+0x3c/0x4c [musb_dsps])
[<bf054488>] (dsps_musb_exit [musb_dsps]) from [<bf043650>] (musb_shutdown+0x80/0x90 [musb_hdrc])
[<bf043650>] (musb_shutdown [musb_hdrc]) from [<bf043a20>] (musb_remove+0x24/0x68 [musb_hdrc])
[<bf043a20>] (musb_remove [musb_hdrc]) from [<c02ca37c>] (platform_drv_remove+0x18/0x1c)
[<c02ca37c>] (platform_drv_remove) from [<c02c8db0>] (__device_release_driver+0x70/0xc8)
[<c02c8db0>] (__device_release_driver) from [<c02c8e28>] (device_release_driver+0x20/0x2c)
[<c02c8e28>] (device_release_driver) from [<c02c884c>] (bus_remove_device+0xdc/0x10c)
[<c02c884c>] (bus_remove_device) from [<c02c5b20>] (device_del+0x104/0x198)
[<c02c5b20>] (device_del) from [<c02ca838>] (platform_device_del+0x14/0x9c)
[<c02ca838>] (platform_device_del) from [<c02ca8cc>] (platform_device_unregister+0xc/0x20)
[<c02ca8cc>] (platform_device_unregister) from [<bf054194>] (dsps_remove+0x18/0x38 [musb_dsps])
[<bf054194>] (dsps_remove [musb_dsps]) from [<c02ca37c>] (platform_drv_remove+0x18/0x1c)
[<c02ca37c>] (platform_drv_remove) from [<c02c8db0>] (__device_release_driver+0x70/0xc8)
[<c02c8db0>] (__device_release_driver) from [<c02c8e28>] (device_release_driver+0x20/0x2c)
[<c02c8e28>] (device_release_driver) from [<c02c884c>] (bus_remove_device+0xdc/0x10c)
[<c02c884c>] (bus_remove_device) from [<c02c5b20>] (device_del+0x104/0x198)
[<c02c5b20>] (device_del) from [<c02c5bc0>] (device_unregister+0xc/0x20)
[<c02c5bc0>] (device_unregister) from [<bf05900c>] (of_remove_populated_child+0xc/0x14 [musb_am335x])
[<bf05900c>] (of_remove_populated_child [musb_am335x]) from [<c02c5c48>] (device_for_each_child+0x44/0x70)
[<c02c5c48>] (device_for_each_child) from [<bf05902c>] (am335x_child_remove+0x18/0x30 [musb_am335x])
[<bf05902c>] (am335x_child_remove [musb_am335x]) from [<c02ca37c>] (platform_drv_remove+0x18/0x1c)
[<c02ca37c>] (platform_drv_remove) from [<c02c8db0>] (__device_release_driver+0x70/0xc8)
[<c02c8db0>] (__device_release_driver) from [<c02c94c8>] (driver_detach+0xb4/0xb8)
[<c02c94c8>] (driver_detach) from [<c02c8ab4>] (bus_remove_driver+0x4c/0xa0)
[<c02c8ab4>] (bus_remove_driver) from [<c007fc40>] (SyS_delete_module+0x128/0x1cc)
[<c007fc40>] (SyS_delete_module) from [<c000e500>] (ret_fast_syscall+0x0/0x48)

Fixes: 97238b35 ("usb: musb: dsps: use proper child nodes")
Cc: <stable@vger.kernel.org> # v3.12+
Acked-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Even though usb_functionfs_descs_head structure is now deprecated,
it has been used by some user space tools.  Its removel in commit
[ac8dde11: “Add flags to descriptors block”] was an oversight
leading to build breakage for such tools.

Bring it back so that old user space tools can still be build
without problems on newer kernel versions.

Cc: <stable@vger.kernel.org>  # 3.14
Reported-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Reported-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This reverts commit f2af7412.

There is a better fix for this build error coming in a following
patch.
Signed-of-by: Felipe Balbi <balbi@ti.com>

BABBLE and RESET share the same interrupt. The interrupt
is considered to be RESET if MUSB is in peripheral mode and
as a BABBLE if MUSB is in HOST mode.

Handle babble condition iff MUSB is in HOST mode.

Fixes: ca88fc2e (usb: musb: add a work_struct to recover from babble errors)
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This reverts commit 1826e9b1 (usb: gadget: gadgetfs: use
after free in dev_release()) and places the call to
put_dev() after setting the state.

If this is not the final call to dev_release() and the
state is not reset to STATE_DEV_DISABLED and hence all
further open() calls to the gadgetfs ep0 device will
fail with EBUSY.
Signed-off-by: Marcus Nutzinger <marcus.nutzinger@theobroma-systems.com>
Reviewed-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Function's interface directories need to be created when the function
directory is created, but interface numbers are not known until
the gadget is ready and bound to udc, so we cannot use numbers
as part of interface directory names.
Let the client decide what names to use.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

A number of variables serve a generic purpose of handling
"compatible id" and "subcompatible id", but the names suggest they
are for rndis only. Rename to reflect variables' purpose.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

If the descriptors do not need any strings and user space sends empty
set of strings, the ffs->stringtabs field remains NULL.  Thus
*ffs->stringtabs in functionfs_bind leads to a NULL pointer
dereferenece.

The bug was introduced by commit [fd7c9a00: “use usb_string_ids_n()”].

While at it, remove double initialisation of lang local variable in
that function.

ffs->strings_count does not need to be checked in any way since in
the above scenario it will remain zero and usb_string_ids_n() is
a no-operation when colled with 0 argument.

Cc: <stable@vger.kernel.org>  # v2.6.36+
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

There is a regression in the upcoming v3.16-rc1, that is caused
by a problem that has been around for a while but now finally
hangs the system. The bootcrawl looks like this:

pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already
requested by a03e0000.usb_per5; cannot claim for musb-hdrc.0.auto
pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.0.auto) status -22
pinctrl-nomadik soc:pinctrl: could not request pin 256
(GPIO256_AF28) from group usb_a_1  on device pinctrl-nomadik
musb-hdrc musb-hdrc.0.auto: Error applying setting, reverse
things back
HS USB OTG: no transceiver configured
musb-hdrc musb-hdrc.0.auto: musb_init_controller failed
with status -517
platform musb-hdrc.0.auto: Driver musb-hdrc requests
probe deferral
(...)

The ux500 MUSB driver propagates the OF node to the dynamically
created musb-hdrc device, which is incorrect as it makes the OF
core believe there are two devices spun from the very same
DT node, which confuses other parts of the device core, notably
the pin control subsystem, which will try to apply all the pin
control settings also to the HDRC device as it gets
instantiated. (The OMAP2430 for example, does not set the
of_node member.)

Cc: <stable@vger.kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Current usbhs gadget driver didn't complete STATUS stage after receiving.
It wasn't problem for us before, because some USB class doesn't use
DATA OUT stage in control transfer.
But, it is required on some device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When disconnecting, it's possible that another thread has already made it
into eth_start_xmit before we call netif_stop_queue. This can lead to a
crash as eth_start_xmit tries to use resources that gether_disconnect is
freeing. Use netif_tx_lock/unlock around netif_stop_queue to ensure no
threads are executing during the remainder of gether_disconnect.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Tested-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The dwc3 wrapper driver should not be fiddling with the core interrupts.
Disabling the core interrupts in prepare stops xhci from proper operation.
So remove disable/enable of core interrupts from prepare/complete.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Following crash is seen on dwc3_omap removal
Unable to handle kernel NULL pointer dereference at virtual address 00000018
pgd = ec098000
[00000018] *pgd=ad1f9831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in: usb_f_ss_lb g_zero usb_f_acm u_serial usb_f_ecm u_ether libcomposite configfs snd_usb_audio snd_usbmidi_lib snd_rawmidi snd_hwdep snd_soc_omap snd_pcm_dmaengine snd_soc_core snd_compress snd_pcm snd_tim]
CPU: 0 PID: 1296 Comm: rmmod Tainted: G        W     3.15.0-rc4-02716-g95c4e18-dirty #10
task: ed05a080 ti: ec368000 task.ti: ec368000
PC is at release_resource+0x14/0x7c
LR is at release_resource+0x10/0x7c
pc : [<c0044724>]    lr : [<c0044720>]    psr: 60000013
sp : ec369ec0  ip : 60000013  fp : 00021008
r10: 00000000  r9 : ec368000  r8 : c000e7a4
r7 : 00000081  r6 : bf0062c0  r5 : ed7cd000  r4 : ed7d85c0
r3 : 00000000  r2 : 00000000  r1 : 00000011  r0 : c086d08c
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c5387d  Table: ac098059  DAC: 00000015
Process rmmod (pid: 1296, stack limit = 0xec368248)
Stack: (0xec369ec0 to 0xec36a000)
9ec0: 00000000 00000001 ed7cd000 c034de94 ed7cd010 ed7cd000 00000000 c034e194
9ee0: 00000000 bf0062cc ed7cd010 c03490b0 ed154cc0 ed4c2570 ed2b8410 ed156810
ed156810 bf006d24 c034db9c c034db84 c034c518
9f20: bf006d24 ed156810 bf006d24 c034cd2c bf006d24 bf006d68 00000800 c034c340
9f40: 00000000 c00a9e5c 00000020 00000000 bf006d68 00000800 ec369f4c 33637764
9f60: 616d6f5f 00000070 00000001 ec368000 ed05a080 c000e670 00000001 c0084010
9f80: 00021088 00000800 00021088 00000081 80000010 0000e6f4 00021088 00000800
9fa0: 00021088 c000e5e0 00021088 00000800 000210b8 00000800 e04f6d00 e04f6d00
9fc0: 00021088 00000800 00021088 00000081 00000001 00000000 be91de08 00021008
9fe0: 4d768880 be91dbb4 b6fc5984 4d76888c 80000010 000210b8 00000000 00000000
[<c0044724>] (release_resource) from [<c034de94>] (platform_device_del+0x6c/0x9c)
[<c034de94>] (platform_device_del) from [<c034e194>] (platform_device_unregister+0xc/0x18)
[<c034e194>] (platform_device_unregister) from [<bf0062cc>] (dwc3_omap_remove_core+0xc/0x14 [dwc3_omap])
[<bf0062cc>] (dwc3_omap_remove_core [dwc3_omap]) from [<c03490b0>] (device_for_each_child+0x34/0x74)
[<c03490b0>] (device_for_each_child) from [<bf0062b4>] (dwc3_omap_remove+0x6c/0x78 [dwc3_omap])
[<bf0062b4>] (dwc3_omap_remove [dwc3_omap]) from [<c034db9c>] (platform_drv_remove+0x18/0x1c)
[<c034db9c>] (platform_drv_remove) from [<c034c518>] (__device_release_driver+0x70/0xc8)
[<c034c518>] (__device_release_driver) from [<c034cd2c>] (driver_detach+0xb4/0xb8)
[<c034cd2c>] (driver_detach) from [<c034c340>] (bus_remove_driver+0x4c/0x90)
[<c034c340>] (bus_remove_driver) from [<c00a9e5c>] (SyS_delete_module+0x10c/0x198)
[<c00a9e5c>] (SyS_delete_module) from [<c000e5e0>] (ret_fast_syscall+0x0/0x48)
Code: e1a04000 e59f0068 eb14505e e5943010 (e5932018)
---[ end trace 7e2a8746ff4fc811 ]---
Segmentation fault

[ balbi@ti.com : add CONFIG_OF dependency ]
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This should be return -ENOMEM.  The current code returns successs.

Fixes: de7a8d2d ('usb: gadget: f_rndis: OS descriptors support')
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Commit [ac8dde11: “usb: gadget: f_fs: Add flags to descriptors block”]
which introduced a new descriptor format for FunctionFS removed the
usb_functionfs_descs_head structure, which is still used by ffs-test.
tool.

Convert ffs-test by converting it to use the new header format.  For
testing kernels prior to 3.14 (when the new format was introduced) and
parsing of the legacy headers in the new kernels, provide a compilation
flag to make the tool use the old format.

Finally, include information as to when the legacy FunctionFS headers
format has been deprecated (which is also when the new one has been
introduced).
Reported-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In ISOC transfers, when free_slot points to the last TRB (i.e. Link
TRB), and all queued requests meet Missed Interval Isoc error, busy_slot
points to trb0.
	busy_slot->trb0
		   trb1
		   ...
	free_slot->trb31(Link TRB)

After end transfer and receiving the XferNotReady event, trb_left is
caculated as 1 which is wrong, and no TRB will be primed to the
endpoint.

The root cause is free_slot is not increased the same way as busy_slot.
When busy_slot is increased by one, it checks if points to a link TRB
after increasement, but free_slot checks it before increasement.
free_slot should behave the same as busy_slot to make the trb_left
caculation correct.
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Pull networking fixes from David Miller:

 1) Fix checksumming regressions, from Tom Herbert.

 2) Undo unintentional permissions changes for SCTP rto_alpha and
    rto_beta sysfs knobs, from Denial Borkmann.

 3) VXLAN, like other IP tunnels, should advertize it's encapsulation
    size using dev->needed_headroom instead of dev->hard_header_len.
    From Cong Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: sctp: fix permissions for rto_alpha and rto_beta knobs
  vxlan: Checksum fixes
  net: add skb_pop_rcv_encapsulation
  udp: call __skb_checksum_complete when doing full checksum
  net: Fix save software checksum complete
  net: Fix GSO constants to match NETIF flags
  udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
  vxlan: use dev->needed_headroom instead of dev->hard_header_len
  MAINTAINERS: update cxgb4 maintainer

Pull more clock framework updates from Mike Turquette:
 "This contains the second half the of the clk changes for 3.16.

  They are simply fixes and code refactoring for the OMAP clock drivers.
  The sunxi clock driver changes include splitting out the one
  mega-driver into several smaller pieces and adding support for the A31
  SoC clocks"

* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
  clk: sunxi: document PRCM clock compatible strings
  clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
  clk: sun6i: Protect SDRAM gating bit
  clk: sun6i: Protect CPU clock
  clk: sunxi: Rework clock protection code
  clk: sunxi: Move the GMAC clock to a file of its own
  clk: sunxi: Move the 24M oscillator to a file of its own
  clk: sunxi: Remove calls to clk_put
  clk: sunxi: document new A31 USB clock compatible
  clk: sunxi: Implement A31 USB clock
  ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
  CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
  ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
  CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
  CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
  dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
  ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
  CLK: TI: gate: add composite interface clock to OMAP2 only build
  ARM: OMAP2: clock: add DT boot support for cpufreq_ck
  CLK: TI: OMAP2: add clock init support
  ...

Pull NVMe update from Matthew Wilcox:
 "Mostly bugfixes again for the NVMe driver.  I'd like to call out the
  exported tracepoint in the block layer; I believe Keith has cleared
  this with Jens.

  We've had a few reports from people who're really pounding on NVMe
  devices at scale, hence the timeout changes (and new module
  parameters), hotplug cpu deadlock, tracepoints, and minor performance
  tweaks"

[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
  end up going away when mq conversion happens ]

* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
  NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
  NVMe: Use Log Page constants in SCSI emulation
  NVMe: Define Log Page constants
  NVMe: Fix hot cpu notification dead lock
  NVMe: Rename io_timeout to nvme_io_timeout
  NVMe: Use last bytes of f/w rev SCSI Inquiry
  NVMe: Adhere to request queue block accounting enable/disable
  NVMe: Fix nvme get/put queue semantics
  NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
  NVMe: Make admin timeout a module parameter
  NVMe: Make iod bio timeout a parameter
  NVMe: Prevent possible NULL pointer dereference
  NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
  NVMe: Update data structures for NVMe 1.2
  NVMe: Enable BUILD_BUG_ON checks
  NVMe: Update namespace and controller identify structures to the 1.1a spec
  NVMe: Flush with data support
  NVMe: Configure support for block flush
  NVMe: Add tracepoints
  NVMe: Protect against badly formatted CQEs
  ...

Commit 3fd091e7 ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.

RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:

  [...]
  C3)  When a new RTT measurement R' is made, set

       RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|

       and

       SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'

       Note: The value of SRTT used in the update to RTTVAR
       is its value before updating SRTT itself using the
       second assignment. After the computation, update
       RTO <- SRTT + 4 * RTTVAR.

  C4)  When data is in flight and when allowed by rule C5
       below, a new RTT measurement MUST be made each round
       trip. Furthermore, new RTT measurements SHOULD be
       made no more than once per round trip for a given
       destination transport address. There are two reasons
       for this recommendation: First, it appears that
       measuring more frequently often does not in practice
       yield any significant benefit [ALLMAN99]; second,
       if measurements are made more often, then the values
       of RTO.Alpha and RTO.Beta in rule C3 above should be
       adjusted so that SRTT and RTTVAR still adjust to
       changes at roughly the same rate (in terms of how many
       round trips it takes them to reflect new values) as
       they would if making only one measurement per
       round-trip and using RTO.Alpha and RTO.Beta as given
       in rule C3. However, the exact nature of these
       adjustments remains a research issue.
  [...]

While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.

Fixes: 3fd091e7 ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
Fixes related to some recent checksum modifications.

- Fix GSO constants to match NETIF flags
- Fix logic in saving checksum complete in __skb_checksum_complete
- Call __skb_checksum_complete from UDP if we are checksumming over
  whole packet in order to save checksum.
- Fixes to VXLAN to work correctly with checksum complete
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet
header to work properly with checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is used by UDP encapsulation protocols in RX when
crossing encapsulation boundary. If ip_summed is set to
CHECKSUM_UNNECESSARY and encapsulation is not set, change to
CHECKSUM_NONE since the checksum has not been validated within the
encapsulation. Clears csum_valid by the same rationale.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In __udp_lib_checksum_complete check if checksum is being done over all
the data (len is equal to skb->len) and if it is call
__skb_checksum_complete instead of __skb_checksum_complete_head. This
allows checksum to be saved in checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead5
("net: Save software checksum complete") is not correct.

This patch:
1) Restores code in __skb_checksum_complete_header except for setting
   CHECKSUM_UNNECESSARY. This function may be calculating checksum on
   something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
   checksum 0..skb->len is calculated without adding in pseudo header.
   This value is saved in skb->csum and then the pseudo header is added
   to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
   set skb->csum_valid to whether checksum of zero was computed. This
   allows skb_csum_unnecessary to return true without changing to
   CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Joseph Gasparakis reported that VXLAN GSO offload stopped working with
i40e device after recent UDP changes. The problem is that the
SKB_GSO_* bits are out of sync with the corresponding NETIF flags. This
patch fixes that. Also, we add BUILD_BUG_ONs in net_gso_ok for several
GSO constants that were missing to avoid the problem in the future.
Reported-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull more SCSI updates from James Bottomley:
 "This is just a couple of drivers (hpsa and lpfc) that got left out for
  further testing in linux-next.  We also have one fix to a prior
  submission (qla2xxx sparse)"

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
  qla2xxx: fix sparse warnings introduced by previous target mode t10-dif patch
  lpfc: Update lpfc version to driver version 10.2.8001.0
  lpfc: Fix ExpressLane priority setup
  lpfc: mark old devices as obsolete
  lpfc: Fix for initializing RRQ bitmap
  lpfc: Fix for cleaning up stale ring flag and sp_queue_event entries
  lpfc: Update lpfc version to driver version 10.2.8000.0
  lpfc: Update Copyright on changed files from 8.3.45 patches
  lpfc: Update Copyright on changed files
  lpfc: Fixed locking for scsi task management commands
  lpfc: Convert runtime references to old xlane cfg param to fof cfg param
  lpfc: Fix FW dump using sysfs
  lpfc: Fix SLI4 s abort loop to process all FCP rings and under ring_lock
  lpfc: Fixed kernel panic in lpfc_abort_handler
  lpfc: Fix locking for postbufq when freeing
  lpfc: Fix locking for lpfc_hba_down_post
  lpfc: Fix dynamic transitions of FirstBurst from on to off
  hpsa: fix handling of hpsa_volume_offline return value
  hpsa: return -ENOMEM not -1 on kzalloc failure in hpsa_get_device_id
  hpsa: remove messages about volume status VPD inquiry page not supported
  ...

Pull more btrfs updates from Chris Mason:
 "This has a few fixes since our last pull and a new ioctl for doing
  btree searches from userland.  It's very similar to the existing
  ioctl, but lets us return larger items back down to the app"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: fix error handling in create_pending_snapshot
  btrfs: fix use of uninit "ret" in end_extent_writepage()
  btrfs: free ulist in qgroup_shared_accounting() error path
  Btrfs: fix qgroups sanity test crash or hang
  btrfs: prevent RCU warning when dereferencing radix tree slot
  Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
  btrfs: new ioctl TREE_SEARCH_V2
  btrfs: tree_search, search_ioctl: direct copy to userspace
  btrfs: new function read_extent_buffer_to_user
  btrfs: tree_search, copy_to_sk: return needed size on EOVERFLOW
  btrfs: tree_search, copy_to_sk: return EOVERFLOW for too small buffer
  btrfs: tree_search, search_ioctl: accept varying buffer
  btrfs: tree_search: eliminate redundant nr_items check

Pull aio fix and cleanups from Ben LaHaise:
 "This consists of a couple of code cleanups plus a minor bug fix"

* git://git.kvack.org/~bcrl/aio-next:
  aio: cleanup: flatten kill_ioctx()
  aio: report error from io_destroy() when threads race in io_destroy()
  fs/aio.c: Remove ctx parameter in kiocb_cancel

Tetsuo Handa wrote:
 "Commit 62a8067a ("bio_vec-backed iov_iter") introduced an unnamed
  union inside a struct which gcc-4.4.7 cannot handle.  Name the unnamed
   union as u in order to fix build failure"

Let's do this instead: there is only one place in the entire tree that
steps into this breakage.  Anon structs and unions work in older gcc
versions; as the matter of fact, we have those in the tree - see e.g.
struct ieee80211_tx_info in include/net/mac80211.h

What doesn't work is handling their initializers:

struct {
	int a;
	union {
		int b;
		char c;
	};
} x[2] = {{.a = 1, .c = 'a'}, {.a = 0, .b = 1}};

is the obvious syntax for initializer, perfectly fine for C11 and
handled correctly by gcc-4.7 or later.

Earlier versions, though, break on it - declaration is fine and so's
access to fields (i.e.  x[0].c = 'a'; would produce the right code), but
members of the anon structs and unions are not inserted into the right
namespace.  Tellingly, those older versions will not barf on struct {int
a; struct {int a;};}; - looks like they just have it hacked up somewhere
around the handling of .  and -> instead of doing the right thing.

The easiest way to deal with that crap is to turn initialization of
those fields (in the only place where we have such initializer of
iov_iter) into plain assignment.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull HSI build fixes from Sebastian Reichel:
 - tighten dependency between ssi-protocol and omap-ssi to fix build
   failures with randconfig.
 - use normal module refcounting in omap driver to fix build with
   disabled module support

* tag 'hsi-for-3.16-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
  hsi: omap_ssi_port: use normal module refcounting
  HSI: fix omap ssi driver dependency

Pull GPIO fix from Linus Walleij:
 "A first GPIO fix for the v3.16 series, this was serious since it
  blocks the OMAP boot.

  Sending you this vital fix before leaving for a short vacation so it
  does not sit collecting dust in my tree for no good reason.

  Apart from this, our v3.16 cycle looks like a good start"

* tag 'gpio-v3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: of: Fix handling for deferred probe for -gpio suffix

Pull x86 vdso fixes from Peter Anvin:
 "Fixes for x86/vdso.

  One is a simple build fix for bigendian hosts, one is to make "make
  vdso_install" work again, and the rest is about working around a bug
  in Google's Go language -- two are documentation patches that improves
  the sample code that the Go coders took, modified, and broke; the
  other two implements a workaround that keeps existing Go binaries from
  segfaulting at least"

* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/vdso: Fix vdso_install
  x86/vdso: Hack to keep 64-bit Go programs working
  x86/vdso: Add PUT_LE to store little-endian values
  x86/vdso/doc: Make vDSO examples more portable
  x86/vdso/doc: Rename vdso_test.c to vdso_standalone_test_x86.c
  x86, vdso: Remove one final use of htole16()

Pull hwmon updates from Guenter Roeck:
 - new driver for Sensirion SHTC1 humidity / temperature sensor
 - convert ltc4151 and vexpress drivers to use devm functions
 - drop generic chip detection from lm85 driver
 - avoid forward declarations in atxp1 driver
 - fix sign extensions in ina2xx driver

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: vexpress: Use devm helper for hwmon device registration
  hwmon: (atxp1) Avoid forward declaration
  hwmon: add support for Sensirion SHTC1 sensor
  hwmon: (ltc4151) Convert to devm_hwmon_device_register_with_groups
  hwmon: (lm85) Drop generic detection
  hwmon: (ina2xx) Cast to s16 on shunt and current regs

Its too easy to add thousand of UDP sockets on a particular bucket,
and slow down an innocent multicast receiver.

Early demux is supposed to be an optimization, we should avoid spending
too much time in it.

It is interesting to note __udp4_lib_demux_lookup() only tries to
match first socket in the chain.

10 is the threshold we already have in __udp4_lib_lookup() to switch
to secondary hash.

Fixes: 421b3885 ("udp: ipv4: Add udp early demux")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Held <drheld@google.com>
Cc: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we mirror packets from a vxlan tunnel to other device,
the mirror device should see the same packets (that is, without
outer header). Because vxlan tunnel sets dev->hard_header_len,
tcf_mirred() resets mac header back to outer mac, the mirror device
actually sees packets with outer headers

Vxlan tunnel should set dev->needed_headroom instead of
dev->hard_header_len, like what other ip tunnels do. This fixes
the above problem.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: stephen hemminger <stephen@networkplumber.org>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hari's been doing the patch submissions for a while now and he'll be
taking over as maintainer.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>